Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “rod”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Full Rod Length Gamma Spectroscopy Measurements of LWR Used Fuel Rods

Twenty-five high-burnup pressurized water reactor used fuel rods were scanned in the Irradiated Fuels Examination Laboratory at Oak Ridge National Laboratory with a high-resolution gamma spectrometer. A planar high-purity germanium detector was used across an energy range from 60 keV to 3 MeV. Gamma spectra of individual fuel rods were collected in 4.5 mm steps along the entire length of each rod. Additional spectra were collected on select rods in rotational increments of 30 degrees to provide data on the distribution of fission products along the rod perimeter.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Gold Quantum Rods: Modulation of Singlet and Triplet Exciton Populations by the Rod Length

Abstract Gold quantum rods (QRs) of Au60, Au78, Au96, and Au114 (protected by thiolate ligands) exhibit exclusive fluorescence, which is different from the shorter Au42 QR with dual emission (fluorescence + phosphorescence). Herein, we report the excitation wavelength-dependent near-infrared-II photoluminescence (PL) and exciton dynamics of this series of QRs. Interestingly, the fluorescence quantum yield (QY) of the QRs is much higher (2–10×) when the lowest singlet excited state (S1) is excited compared to the excitation of high-lying states (Sn). A metastable intermediate singlet state (denoted S′) is identified by transient absorption spectroscopy when Sn is excited, and this S′ state leads to fast “skybridge” intersystem crossing (ISC), which contributes primarily (>60%) to the total triplet population. With increasing aspect ratio (AR) of QRs (from 6.3 to 18.7), nonradiative processes accelerate, leading to fast decay of the S1 state (hence, less QY) and of the T1 state (barely phosphorescent). A detailed energy flow mechanism is determined for the QRs after photoexcitation, which offers a design principle for manipulation of exciton dynamics toward potential utilization of higher excited states in applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Tantalum Experiments in Fully-Reflected Water-Moderated Triangular-Pitched U(6.90)O 2 Fuel Rod Lattices (1.02 cm Pitch)

The United States (US) Department of Energy (DOE) Nuclear Energy Research Initiative funded the design and construction of the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratories (SNL). The start-up of the experiment facility and the execution of the experiments described here were funded by the DOE Nuclear Criticality Safety Program. The 7uPCX is designed to investigate critical systems with fuel for light water reactors in the enrichment range above 5 % 235 U. The 7uPCX assembly is a water moderated and — reflected array of aluminum-clad U(6.90 %)O 2 fuel rods. Other critical experiments performed in the 7uPCX assembly are documented in LEU-COMP-THERM-078, LEU-COMP-THERM-080, LEU-COMP-THERM 096, LEU- COMP-THERM-097, LEU-COMP-THERM-101, LEU-COMP-THERM-102, and LEU-COMP-THERM-111. Applied interests in neutron-absorbing elements at epithermal and intermediate neutron energy ranges at DOE’s Hanford Site and Savannah River Site were identified through DOE Office of Environmental Management (EM) workshops and needs surveys performed in conjunction with the National Nuclear Security Administration/Nuclear Criticality Safety Program. In response, a team lead by Oak Ridge National Laboratory (ORNL) performed a study evaluating the use of 7uPCX for testing the epithermal cross sections of materials at SNL. This marked the inception of the set of experiments described here. The purpose of these experiments was to measure the effects of tantalum in nearly-critical systems. The tantalum was introduced into the fuel arrays as experiment rods within a central test region. The central test region was designed to target the epithermal neutron energy range by providing a dry cylindrical cavity constructed of aluminum and lined with 0.04 in (0.1016 cm) thick cadmium sheet. The central test region has an outer diameter of 3.75 in (9.525 cm) length of 31 in (78.74 cm) and can hold 85 tantalum rods nominally 0.25 in (0.635 cm) outside diameter and 31.25 in (79.375 cm) long. The critical experiments were done using a set of triangular-pitched grid plates fabricated for these experiments. The grid plate set accommodated a fuel array of a total of 2016 fuel rod positions on a pitch of 0.4 in (1.016 cm) in a series of 21 hexagonal rings positioned around the central test region. The fuel used in these experiments was fabricated using unirradiated 6.90 % enriched UO 2 fuel pellets from fuel elements designed to be used in the internal nuclear superheater section of the Pathfinder boiling water reactor operated in South Dakota by the Northern States Power Company in the 1960s. The fuel elements were obtained from The Pennsylvania State University where they had been stored for many years. The fuel pellets in those fuel elements were removed from the original Incoloy cladding and reclad in 3003 aluminum tubes and end caps for use in the experiments reported here. The eight cases in this experiment series were performed in 2024 in the Sandia Critical Experiments (SCX) at the Sandia Pulsed Reactor Facility by varying the number of fuel rods in the critical assembly. The personnel involved in conducting these experiments included David Ames, Elijah Lutz, Beth Hanson, Patrick Ward, Jason Soares, and Augie Chapa from SNL, as well as Mathieu Dupont and B.J. Marshall from ORNL. Case 1 had no tantalum experiment rods. Case 2 had seven tantalum rods in the center of the central test region. Case 3 had 18 tantalum rods in the third hexagonal ring of the central test region. Case 4 had 19 tantalum rods in the center of the central test region. Case 5 had 30 tantalum rods in the outer most positions of the central test region. Case 6 had 37 tantalum rods in the center of the central test region. Case 7 had 61 tantalum rods in the center of the central test region. Case 8 had 85 tantalum rods filling all positions in the central test region. All eight critical experiments are judged to be acceptable as benchmark experiments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

NON-DESTRUCTIVE POST IRRADIATION EXAMINATION OF FIRST CYCLE ACCIDENT TOLERANT AND ADVANCED ZIRCONIUM ALLOY HIGH BURNUP FUEL RODS

Post irradiation examination (PIE) of accident tolerant fuel concepts and high burnup uranium dioxide advanced zirconium alloy clad fuel contribute to near term nuclear industry goals of enhancing light water reactor safety and economics. Westinghouse is developing chromium coated zirconium alloy cladding as an accident tolerant fuel option for current pressurized water reactors. Examination of high burnup fuel further augments the technical foundation for extending the peak rod average burnup limits beyond the current regulatory limit of 62 MWd/kgU. Seven fuel rods were received at the Oak Ridge National Laboratory Irradiated Fuel Examination Facility. This includes three chromium coated zirconium alloy fuel rods and four high burnup advanced zirconium alloy fuel rods. Six of the seven rods were fueled with standard uranium dioxide while one of the chromium coated rods contained Westinghouse’s ADOPT fuel. The overall hot-cell PIE plan and some PIE results have been presented previously. This paper focuses on the additional non-destructive examination and fission gas release. Highlights from visual examination of these rods are presented. The chromium coating showed little to no visual change following irradiation. Observations of the axial burnup trends in the fuel rods are derived from full rod axial gamma-ray scans with additional observations related to local fission product migration. The axial dimensional changes of the seven rods are evaluated. As expected, creep down had not yet occurred in the chromium coated rods, and the maximum diameter strain in the high burnup advanced zirconium alloy cladding was less than 0.5%. Finally, the steady state fission gas release for these rods was measured ranging from 4.1% to 17.6% which matched expectation from literature. These fuel rods now await further destructive examination.

Harp, Jason↗
DOE OSTI2026

Design and fabrication of a four-rod radio frequency quadrupole with a variable aperture

Radiofrequency quadrupole (RFQ) linear accelerators with variable aperture cell parameters offer an effective means of accelerating high-intensity ion beams exceeding 100 mA and have been implemented in various RFQ designs. However, in a four-rod RFQ, the use of dielectric perturbation methods to measure the voltage distribution behind the rod electrodes is not applicable when implementing variable aperture geometries, because changes in the rod shape influence the electric field at the location of the perturbation element. Therefore, it was necessary to design the rod profile for each cell such that the electric field distribution behind the rods remains unaffected by changes in the aperture. In this study, we present a method to adjust the voltage distribution by modifying the geometry of the rod electrodes according to each cell's aperture parameters. This design approach enables the integration of variable aperture cells into a four-rod RFQ linac, significantly enhancing the achievable beam current. To ensure uniform capacitance and maintain a constant rod-electrode voltage despite variations in the average aperture radius, we developed a systematic method for shaping the rod electrodes. This method was refined using two-dimensional (2D) and three-dimensional (3D) electromagnetic field simulations to optimize the electrode cross-sectional profiles. The fabricated rod electrodes were then installed in a four-rod RFQ, and the electric field distribution was measured using the perturbation method and tuned by adjusting the base plates. As a result, the measured variation of ±1.1 % confirms that this design methodology can produce a sufficiently uniform voltage distribution for high-current beam acceleration. These results demonstrate the practical feasibility of a variable-aperture four-rod RFQ linac.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Sister Rod Destructive Examinations (FY23) Appendix B: Segmentation, Defueling, Metallographic Data and Total Cladding Hydrogen

As a part of the DOE-NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWd/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called sister rods or sibling rods are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO ® , and M5 ® . The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Both composite fuel and defueled cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the post-irradiation examination data and associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and subsequent disposition of the SNF. This report documents the status of the ORNL Phase 1 DE activities related to: Rough segmentation (RS), Defueling (DEF), DE.02 optical microscopy (MET), and DE.03, cladding total hydrogen measurements. It is a cumulative update to the FY22 status report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Effect of feed-rod tilting on friction surfacing of steel

During the friction surfacing process, the forge-axial force, rotation rate, and traverse speed of the consumable feed-rod play crucial roles in determining the deposition rate and layer morphology. Although some researchers have studied the enhancement of deposition by introducing a backward tilt relative to the traverse direction, there has been limited investigation into the effects of other tilt orientations. Therefore, this study aims to provide a more comprehensive understanding of feed-rod tilting in friction surfacing. In this investigation, the consumable feed-rod undergoes tilting in four distinct directions: forward, backward, advancing side, and retreating side, each tested at two different tilt angles (1.5° and 3.0°). The results reveal that the feed-rod tilting can influence the deposition dynamics by altering the location and area of the rubbing interface situated between the feed-rod and the substrate. Moreover, the feed-rod tilting can significantly enhance the bond width, deposition rate, and deposition efficiency. The enhancement in deposition efficiency signifies a successful reduction in flash formation. Furthermore, a distinct layered microstructure is evident within each deposition layer, regardless of tilt conditions, indicating the unique deposition process inherent to friction surfacing. Finally, the innovative approach proposed in this study not only offers a straightforward and feasible means to improve deposition rate and efficiency but also expands the potential for constructing more intricate geometries or authentic surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multidimensional modeling of fuel-cladding friction in an LWR fuel rod

Solving finite element problems with friction often increases the level of difficulty to obtain properly converged solutions. This type of challenge becomes more salient when advanced, possibly multiscale, material models are employed to capture the thermomechanical behavior of fuel and cladding materials. Here the present work details our recent developments in a nuclear fuel performance finite element code for the systematic consideration of friction in nuclear reactor finite element simulations. We show the application of friction and its effects on the mechanics of light-water reactor rods accounting for various fuel constitutive modeling techniques, model dimensionalities, pellet assumed geometries, and power conditions. In particular, we focus on the fuel rod mechanical behavior as it relates to fuel constitutive models, sensitivity to the coefficient of friction, pellet states of stress, and rod elongation. We discuss the trade-offs between the various multidimensional modeling options and highlight the relevance of frictional effects in the prediction of the fuel rod deformation and interfacial stresses. To relate our modeling results with actual reactor operation, simulations including frictional effects are compared with fuel rod elongation experimental data and some challenges for carrying out a full validation of the axial mechanics are discussed.

42 ENGINEERING↗
DOE OSTI2025

Hydride Reprecipitation in Prototypical 17x17 PWR Fuel Rods after Simulated Vacuum Drying Conditions

Light water reactor (LWR) fuel rod cladding picks up hydrogen as it oxidizes in reactor. Once the hydrogen concentration exceeds the solubility limit, zirconium hydride platelets precipitate, generally in the circumferential direction. In preparation for dry storage, elevated temperatures can dissolve some of the circumferential hydrides, which during cooling can then reprecipitate in a direction perpendicular to the hoop stress (radially). From 2019 to 2024, ORNL published a series of reports that included metallographic observations of cladding after a thermal transient to 400°C followed by slow cooling. The simulated dry storage process was performed on three full-length 17x17 PWR fuel rods at their as-discharged rod internal pressure. There were two important observations from the metallographic examinations of these heat-treated rods: (1) the propensity for hydride reorientation is strongly influenced by nearby as-discharged precipitated hydrides, (2) the radial hydrides observed near the cladding inner diameter were often associated with cracks in the pellet. Subsequent modeling using the BISON fuel performance code that considered the effects of pellet cracks and pellet-cladding bonding observed in high-burnup fuel support the conclusion that pellet cracks enhance the local hoop stress in the cladding creating preferential sites for hydride reorientation, and that the influence of the pellet cannot be ignored in accurate fuel rod performance predictions.

Montgomery, Rose [ORNL] (ORCID:0000000286038936)↗
DOE OSTI2025

Enabling BWR fuel rod analysis in the BISON fuel performance code

Nuclear fuel vendors around the world are pursuing approaches to sustain the existing nuclear reactor fleet consisting primarily of pressurized-water reactors (PWRs) and boiling-water reactors (BWRs). To support the industry's efforts, advanced modeling and simulation tools need to be capable of analyzing both legacy reactor concepts. BWR fuel rods are significantly different than those used in PWRs, which can affect fuel performance analysis. BWR fuel rods include: (1) an extensive use of gadolinia dopant as a burnable absorber, (2) an axial variation in fuel enrichment and gadolinia content, (3) the inclusion of a liner on the inner cladding surface to mitigate the impact of pellet-clad mechanical interaction (which impacts hydrogen and hydride distribution), (4) a lower initial fill gas pressure, (5) bottom-entry control rods, and (6) a lower coolant pressure that results in the two-phase flow boiling phenomenon. Although the primary focus of BISON has been in the area of PWR and advanced reactor fuel analyses, this paper presents the developments in BISON to support BWR fuel performance analysis. An overview of the models that account for the effects of gadolinia is highlighted. Internal mesh generation capabilities to include a liner is presented. Normal operating and transient (reactivity insertion accident) demonstration problems are presented to illustrate the impact of gadolinia, the hydrogen and hydride evolution due to the presence of the liner, and BISON's ability to simulate axially varying enrichments and dopant concentration. Bottom-entry control effects are captured by the axial power peaking factors present in the demonstration cases. Comparisons to integral experiments from the Halden IFA-681 experiments are discussed as initial validation. Reasonable comparisons are obtained for fuel centerline temperature and rod internal pressure as a function of time. In conclusion, simulations of additional experiments containing Gd 2 O 3 -bearing fuel are necessary to completely validate the code for BWR applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Evaluation of RANS vs. LES simulation of fluid flow through 3 × 3 rod bundle with a simple spacer grid as a precursor to coupled fluid–structure interaction simulations

The research literature on Computational Fluid Dynamics (CFD) of coolant flow through rod bundles with spacer-grids and mixing vanes is replete, ranging from high fidelity Large Eddy Simulation (LES)/Direct Numerical Simulation (DNS) simulations to Reynolds-Averaged Navier–Stokes (RANS) modeled studies. The mixing of flow between subchannels and the pressure drop through the bundle are fundamental quantities useful for comparing and evaluating CFD methods. Less commonly observed and compared are the forces exerted onto the structure by the fluid. The present study seeks to evaluate the use of RANS simulations for predicting the structural response to fluid flow. Wall resolved RANS simulations are benchmarked against LES simulations of fluid flow at a Reynolds number of 15,000 through a 3 × 3 fuel rod bundle with a simple spacer grid. Velocity line-plots are compared showing good agreement between RANS and LES results, ascertaining that the former is capable of capturing the essential time-averaged velocity profile. Additionally, the distribution of forces on the spacer grid and fuel rods are collected as a function of time and space. The RANS methods are evaluated using the frequency and magnitude of the fluctuating forces on various portions of the structure as compared to LES. In conclusion, the power spectral density evaluation of the models reveal underprediction of force amplitude on the rod walls by RANS and also discrepancy in the prediction of high frequency spectra, especially in the immediate vicinity of spacer-grid structure, which may be attributed to the lack of random turbulence fluctuation or insufficient modeling of small-scale eddies in RANS simulation.

FIV↗
DOE OSTI2024

Dependence of Heat Removal Rate of Pebble-Based Rods on Inter-Pebble Matrix Fill Fraction

Carbon pebble rods are a promising candidate for use in high heat flux regions of magnetic fusion energy reactor walls. Under high (10 – 50 MW/m 2 ) heat loads, carbon pebble rods release hot pebbles from the exposed surface, carrying away heat as the pebble rod surface recedes. In this work, we show that the surface recession rate during heating can be adjusted by changing the mechanical strength of the extruded rods, modifying the heat removal rate; this is accomplished here by varying the fill fraction of the inter-pebble matrix. A three-dimensional finite element model is presented that captures many experimental observations, including the sphere temperature and the surface recession rate. The model predicts that pebble release is caused by thermally driven crack propagation through the matrix and that the matrix strength against breaking is the single most important material parameter setting the pebble release rate; this prediction is supported by experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fuel Bonding and its Impact on Axial Gas Communication Behavior in Light-Water Reactor Fuel Rods

Axial gas communication concerns the flow along the axial axis of nuclear fuel rods during ramp and loss of coolant accident (LOCA) conditions. During power ramps, the higher linear heat generation rate may cause fuel-to-clad gap closure that may prevent transport of released fission gases to the plenum. Upon reduction in power the gas then can communicate to the plenum. This phenomenon has been experimentally observed by short power dips during ramp experiments completed at the Risø reactor. At higher burnups it is observed that the UO2 fuel and Zircaloy cladding forms a chemical bond. This bond results in complete closure of the gap. When these high burnup rods are subjected to a LOCA, the bond has implications on both the mechanical response (i.e., ballooning) of the cladding and subsequent fuel relocation and axial gas communication. In the LOCA scenario, gas communication is of interest in two different regimes: 1) pre-rupture communication from the plenum towards the lower pressure ballooning area and 2) the post-rupture depressurization of the plenum to the external system pressure. In both regimes the presence of a fuel-to-cladding bond will impact the rate of depressurization. In this work we present a fuel-to-clad bonding model that is coupled to an existing axial gas communication model framework in the BISON fuel performance code. The effect of considering the bond on fuel performance modeling predictions is presented through comparisons to existing experimental data. Experiments considered include several rods from the Halden IFA-650 test series. An evaluation on a full-length rod that explores the combined effect of plenum size and bonding status on axial gas communication behavior is also presented.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Assessment of multi-stage telescopic control rods in a pebble bed reactor. Part II: corrosion and wear performance

To support High-Temperature Gas-Cooled Reactor designs, the effects of corrosion and wear on a SS316L telescopic control rod prototype were investigated in helium at 775 °C with up to 5 ppm oxygen for durations up to 500 h. Three deployment conditions were tested to assess their impact on wear and oxide formation: severe cycles, daily cycles, and gravity-driven deployments. Here, a chromium-rich oxide layer developed on regions exposed to the helium flow, reaching up to 2 µm in the most affected areas. No carburization or decarburization was observed. Oxide breakthrough occurred mainly at grooves and contact points during severe cycling of the telescopic rod, while in the other tests it was limited to contact points. Friction forces increased due to oxide growth and thermal expansion, the latter being the dominant factor, but never enough to hinder rod deployment significantly. Coaxial misalignment of stages was identified as the main potential risk to reliable operation under normal conditions.

Control rod↗
DOE OSTI2024

Complex Phase Transitions of Fully Rigid Sphere–Rod Amphiphiles Induced by Solvent Polarity in Dilute Solutions

Here we report complex macrophase and microphase transitions of rigid amphiphiles with spherical Keggin molecular clusters as the solvophilic block and rod-like rigid oligofluorene (OF) as the solvophobic block in mixed solvents of water and polar organic solvent. By properly adjusting the solvent polarity, the amphiphiles are found to respond accordingly by self-assembling into multilayered incomplete onion-like structures (10–25 vol % THF), single-layered vesicular structures (60 vol % THF), and an unexpected macrophase separation in the middle (40–50 vol % THF), which is due to the anomalous trends in Keggin solubility as a result of the nature of TBA + counterions. The rigidity of the OF block prevents the amphiphile from assembling by following the rule of packing parameters; instead, interdigitation among different rods leads to the formation of the solvophobic domain to achieve self-assembly. The incomplete onion structures are controlled by the interdigitation of rigid rods for the number of layers and the electrostatic interaction among Keggin head groups for the interlayer distance. When the degree of interdigitation becomes lower, the self-assembly process shows a trend that can be explained by the traditional rule of packing parameter. This study demonstrates the formation of different self-assembled structures by rigid amphiphiles and their transitions induced by solvent composition. The self-assembly (microphase separation) of rigid amphiphiles in a dilute solution could indeed represent a broad area containing complicated, uncharted rules.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Structural uniformity and compositional homogeneity of solid-phase alloyed rod

Solid-phase processes have emerged as an alternative to fusion-based alloying to avoid coarse microstructures, undesirable phase formation, and high energy consumption. However, achieving uniform distribution of alloying elements during friction-based processing remains challenging due to highly heterogeneous thermomechanical conditions. This work evaluates the structural uniformity and compositional homogeneity of Al–Cu–Zn alloyed rods produced by friction extrusion (FE) and establishes the role of the rotational speed to feed rate ratio (N/V) on alloying effectiveness. A systematic matrix of FE experiments was conducted at constant extrusion ratio with N/V values ranging from 3.7 to 300. Compositional uniformity was assessed along the rod length (ICP-OES), in three dimensions (X-ray computed tomography), and at the microscale (SEM–EDS), supported by a gray-level co-occurrence matrix (GLCM)–based homogeneity metric. Smoothed particle hydrodynamics (SPH) simulations were used to reveal material flow and thermomechanical fields. Results show that N/V = 100 produces a high-shear mixing zone that eliminates the unmixed core and enables near-full dissolution and dispersion of Cu and Zn. At lower N/V, a laminar flow region persists at the rod center, causing segregation and large composition gradients. The combined experimental–computational analysis provides mechanistic insight into the transition from fragmented particle dispersion to thermomechanically assisted metallurgical mixing. This study establishes processing–structure relationships for solid-phase alloying and provides guidance for achieving homogenized compositions comparable to wrought alloys via rapid, scalable FE processing.

Aluminum↗
DOE OSTI2025

Porous Flow Modeling of Axial Gas Redistribution in Fragmented LWR Fuel Rods using MOOSE

Understanding how gas axially redistributes within fragmented fuel pellets is crucial for predicting the behavior of Light Water Reactor (LWR) fuel rods, particularly during transient and accidental scenarios. The time scale of this phenomenon plays a fundamental role in determining the progression and hazard of a Loss Of Coolant Accident (LOCA), especially when high burn-up fuel in a severe state of fragmentation is involved. Here, this study presents a Computational Fluid Dynamics (CFD) model developed within the Multiphysics Object-Oriented Simulation Environment (MOOSE) to predict the time-scale of plenum depressurization in Light-Water Reactor (LWR) fuel rods driven by axial gas transport through fragmented pellets. The model examines the effects of incorporating non-linearities in the friction term by comparing the results with experimental data. The experiment employed surrogate fuel rods containing pellets subjected to mechanical and/or thermal loadings to simulate various severity of cracking, and aimed at studying the influence of fuel conditions on axial gas redistribution. The results of this analysis indicate that under certain flow regime conditions - determined by the value of an equivalent Reynolds number - accounting for the non-linear friction term in Navier-Stokes equations guarantees better predictions for the time-scale of plenum depressurization. Also, the model enabled the simulation of the pressure decay by assigning distinct permeability values to each pellet instead of a single uniform value. Multiple simulations were run across all possible pellet position combinations, having each pellet assigned with values of permeability extracted from the experimental data. This allows to quantify the impact of the considering various non-uniform distributions of permeability on the dynamics of axial gas redistribution. The present work findings enhance the understanding of axial gas transport, and provide valuable insights for the integration of a model for predicting the axial gas redistribution during a LOCA scenario into the BISON fuel performance code.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Rotation of electrothermal-instability-driven overheating structure due to helically oriented surface magnetic field on a high-current-density aluminum rod

Experiments on the 1-MA, 100-ns-rise-time Mykonos Facility demonstrate rotation of electrothermal instability (ETI)-driven overheating structure on 1.00-mm-diameter, 10-nm-surface roughness, 99.999%-pure aluminum rods, which are pulsed with helically polarized surface magnetic field. Rods are machined to include pairs of 10-micron-scale quasi-hemispherical voids or “engineered defects (ED)” which provide the dominant current density perturbation from which ETI grows most rapidly. Experiments include an axial magnetic field component through the addition of a helically wound return-current electrode or “helical return can (HRC).” For a given HRC design, azimuthal field (B ɵ ) and axial field (B z ) components rise at a prescribed and fixed ratio, driving an increasing magnetic field of constant polarization at the rod's surface; most experiments generated surface magnetic field at a 15-degree field polarization angle (from horizontal) defined as ɸ B = arctan(B z /B ɵ ). ETI-driven emission patterns from individual ED are observed to rotate along ɸ B , while emission patterns from dielectric-coated ED pairs are shown to elongate and preferentially merge along ɸ B , in qualitative agreement with 3D-magnetohydrodynamic simulations. These data strongly support that for a randomized distribution of current density perturbations on a high-current density conductor, nearby perturbations will favorably merge about ɸ B , with the degree of merging increasing with current. Such observations offer fundamental new understanding of the seeding mechanisms of the helical magneto-Rayleigh Taylor (MRT) instabilities observed from axially magnetized magnetically driven imploding liners.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗