Fuel Bonding and its Impact on Axial Gas Communication Behavior in Light-Water Reactor Fuel Rods

Vanwasshenova, Daniel J [Idaho National Laboratory] (ORCID:000000027224777X); Liu, Wenfeng [Structural Integrity Associates]; Gamble, Kyle A [Idaho National Laboratory] (ORCID:0000000284878077); Rashid, Joe [Structural Integrity Associates]; Sweet, Ryan Terrence [Idaho National Laboratory] (ORCID:0000000279194623); Novascone, Stephen R [Idaho National Laboratory] (ORCID:0000000239384326)

DOE OSTI · 3024446

Fuel Bonding and its Impact on Axial Gas Communication Behavior in Light-Water Reactor Fuel Rods

Vanwasshenova, Daniel J [Idaho National Laboratory] (ORCID:000000027224777X)·Liu, Wenfeng [Structural Integrity Associates]·Gamble, Kyle A [Idaho National Laboratory] (ORCID:0000000284878077)·Rashid, Joe [Structural Integrity Associates]·Sweet, Ryan Terrence [Idaho National Laboratory] (ORCID:0000000279194623)·Novascone, Stephen R [Idaho National Laboratory] (ORCID:0000000239384326)

View original source ↗Read source document ↗Export metadata ↓

Abstract

Axial gas communication concerns the flow along the axial axis of nuclear fuel rods during ramp and loss of coolant accident (LOCA) conditions. During power ramps, the higher linear heat generation rate may cause fuel-to-clad gap closure that may prevent transport of released fission gases to the plenum. Upon reduction in power the gas then can communicate to the plenum. This phenomenon has been experimentally observed by short power dips during ramp experiments completed at the Risø reactor. At higher burnups it is observed that the UO2 fuel and Zircaloy cladding forms a chemical bond. This bond results in complete closure of the gap. When these high burnup rods are subjected to a LOCA, the bond has implications on both the mechanical response (i.e., ballooning) of the cladding and subsequent fuel relocation and axial gas communication. In the LOCA scenario, gas communication is of interest in two different regimes: 1) pre-rupture communication from the plenum towards the lower pressure ballooning area and 2) the post-rupture depressurization of the plenum to the external system pressure. In both regimes the presence of a fuel-to-cladding bond will impact the rate of depressurization. In this work we present a fuel-to-clad bonding model that is coupled to an existing axial gas communication model framework in the BISON fuel performance code. The effect of considering the bond on fuel performance modeling predictions is presented through comparisons to existing experimental data. Experiments considered include several rods from the Halden IFA-650 test series. An evaluation on a full-length rod that explores the combined effect of plenum size and bonding status on axial gas communication behavior is also presented.

Explore related subjects

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS Axial Gas Communication BISON Fuel-to-clad Bonding High Burnup

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Vanwasshenova, Daniel J [Idaho National Laboratory] (ORCID:000000027224777X), Liu, Wenfeng [Structural Integrity Associates], Gamble, Kyle A [Idaho National Laboratory] (ORCID:0000000284878077), Rashid, Joe [Structural Integrity Associates], Sweet, Ryan Terrence [Idaho National Laboratory] (ORCID:0000000279194623), Novascone, Stephen R [Idaho National Laboratory] (ORCID:0000000239384326). 2025-10-08. Fuel Bonding and its Impact on Axial Gas Communication Behavior in Light-Water Reactor Fuel Rods. https://www.osti.gov/biblio/3024446

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

DOE OSTI2026

Advanced Test Reactor Safety Basis Update for Gas-Cooled Experiments

The Advanced Test Reactor (ATR) supports neutron irradiation of several types of experiments. One such experiment type is referred to as a gas leadout. Gas leadout experiments actively flow gas through the experiment which allows for active temperature control. It also allows for in-situ data of the experiment. For example, fission gas migration through a fuel sample can be monitored via activity of the sweep gas. Historically, ex-pile equipment and fission product monitors were housed in shielded ATR cubicles. Due to other facility updates, cubicle space is no longer available for gas leadout experiment equipment. To support continued operation of gas leadout experiments, ATR completed a safety basis update that supports a new housing for leadout equipment that may process potentially contaminated gas. In addition to the structure and associated equipment, technical safety requirements regarding handling and storage of experiments needed to be revised to support fueled gas leadout experiments and associated outage configurations. The safety basis update addressed the full lifecycle of these experiments, including experiment movement and interim storage, and credible abnormal events such as failures or leaks in contaminated gas tubing in occupied areas. This paper discusses the completed analyses performed to support the safety basis update associated with gas leadout experiments, including thermal-hydraulic evaluation, probabilistic analysis, and dose consequence analyses.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Synthesis, Characterization, and Testing of High-Lithium-Density Composite Breeders

Solid tritium breeder materials must first and foremost have sufficiently high concentrations of lithium to enable a plant-scale tritium breeding ratio greater than 1:1. However, in addition to lithium content, such breeder materials must also meet other performance metrics including high tritium release rates, thermal conductivities, and irradiation damage tolerance. Perhaps most importantly, tritium breeders must maintain their mechanical integrity during reactor operation so as to avoid degradation which can jeopardize the functionality of the tritium breeder blanket module, which in most designs takes the form of a pebble bed geometry. Unfortunately, the mechanical robustness of most lithium-bearing ceramics under investigation for fusion applications is often inversely related to the lithium atom density. For example, a material such as lithium oxide (Li2O), which has one of the highest lithium atom densities, has a much lower mechanical splitting strength than lithium metatitanate (Li2TiO3), though Li2TiO3 has less than half the lithium atom density of Li2O. This work seeks to provide an alternative to monolithic ceramic tritium breeders, in the form of metal-reinforced composite tritium breeders. Specifically, composite tritium breeders have been synthesized combining Li2O with various ferrous metal reinforcements via electric field assisted sintering (EFAS), also known as spark plasma sintering (SPS). As the metal reinforcement content is increased, metallic networks are observed, via electron microscopy and X-ray computed tomography, to form throughout the composite material. Through destructive mechanical testing, even dilute metal reinforcement loading enables drastic mechanical strength improvements over pure Li2O while higher loadings give rise to quasi-ductile behavior and higher ultimate strengths than Li2TiO3 – while still maintaining a higher density of lithium atoms than Li2TiO3 and many other breeder candidates. In addition to microstructural characterization and mechanical testing, thermal property measurements and hydrogen permeability testing are underway to further assess the suitability of such composites for fusion reactor applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Results of the AGR-5/6/7 UCO TRISO fuel irradiation test in the Advanced Test Reactor

AGR-5/6/7 was the last in a series of irradiation experiments sponsored by the U.S. Department of Energy in support of the development and qualification of TRISO coated particle fuel for use in a high-temperature gas-cooled reactor. This experiment was conducted to verify the performance of the reference-design TRISO-coated low-enriched UCO fuel for modular high-temperature gas-cooled reactor normal operating conditions and to explore fuel performance at temperatures substantially beyond those typical of normal operation. A total of 194 UCO fuel compacts in five capsules were irradiated in the Advanced Test Reactor for 360.9 effective full-power days, achieving final burnup ranging from 5.66% to 15.26% fissions per initial heavy metal atom and fast neutron fluence ranging from 1.62 × 10 25 to 5.55 × 10 25 n/m 2 (E > 0.18 MeV). Calculated time-averaged fuel temperatures ranged from 467 °C to 1432 °C, with a peak fuel temperature of 1536 °C. During the first five irradiation cycles (∼180 effective full-power days), 85m Kr fission gas release-rate-to-birth-rate ratios were 10 −7 –10 −6 , indicating no particle failures. Near the end of the sixth cycle, a substantial number of in-pile particle failures occurred in Capsule 1. The fission gas release from this capsule impacted the readings from the other four capsules and led to unreliable fission gas release measurements for all capsules during the last four cycles. A preliminary post-irradiation examination of Capsule 1 fuel and internal components revealed the in-pile particle failures resulted from operational issues with the capsule, not subpar performance of the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗