Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,441 records · Page 80

Reduction of Fermi level pinning and recombination at polycrystalline CdTe surfaces by laser irradiation

Laser processing of polycrystalline CdTe is a promising approach that could potentially increase module manufacturing throughput while reducing capital expenditure costs. For these benefits to be realized, the basic effects of laser irradiation on CdTe must be ascertained. In this study, we utilize surface photovoltage spectroscopy (SPS) to investigate the changes to the electronic properties of the surface of polycrystalline CdTe solar cell stacks induced by continuous-wave laser annealing. The experimental data explained within a model consisting of two space charge regions, one at the CdTe/air interface and one at the CdTe/CdS junction, are used to interpret our SPS results. The frequency dependence and phase spectra of the SPS signal are also discussed. To support the SPS findings, low-temperature spectrally-resolved photoluminescence and time-resolved photoluminescence were also measured. The data show that a modest laser treatment of 250 W/cm{sup 2} with a dwell time of 20 s is sufficient to reduce the effects of Fermi level pinning at the surface due to surface defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Heteroepitaxy of single-crystal LaLuO{sub 3} on GaAs(111)A by atomic layer deposition

We demonstrate that LaLuO{sub 3} films can be grown epitaxially on sulfur-passivated GaAs(111)A substrates by atomic layer deposition (ALD). Transmission electron microscopy and x-ray diffraction analyses reveal that the oxide film exhibits a cubic structure with a lattice mismatch of -3.8% relative to GaAs. The epitaxial layer has a high degree of crystalline perfection and is relaxed. Electrical characterizations performed on this structure show interfaces with a low interface state density of {approx}7x10{sup 11} cm{sup -2} eV{sup -1}. The measured dielectric constant is around 30, which is close to its bulk crystalline value. In contrast, ALD LaLuO{sub 3} is polycrystalline on GaAs(100) and amorphous on Si(111).

36 MATERIALS SCIENCE↗

Defect structure of epitaxial CrxV1-x thin films on MgO(001)

Epitaxial thin films of CrxV1-x over the entire composition range were deposited on MgO(001) by molecular beam epitaxy. The films exhibited the expected 45° in-plane rotation with no evidence of phase segregation or spinodal decomposition. Pure Cr, with the largest lattice mismatch to MgO, exhibited full relaxation and cubic lattice parameters. As the lattice mismatch decreased with alloy composition, residual epitaxial strain was observed. For 0.2 ≤ x ≤ 0.4 the films were coherently strained to the substrate with associated tetragonal distortion; near the lattice-matched composition of x = 0.33, the films exhibited strain-free pseudomorphic matching to MgO. Unusually, films on the Cr-rich side of the lattice-matched composition exhibited more in-plane compression than expected from the bulk lattice parameters; this result was confirmed with both x-ray diffraction and Rutherford backscattering spectrometry channeling measurements. Although thermal expansion mismatch in the heterostructure may play a role, the dominant mechanism for this phenomenon is still unknown. High resolution transmission electron microscopy was utilized to characterize the misfit dislocation network present at the film/MgO interface. Dislocations were found to be present with a non-uniform distribution, which is attributed to the Volmer-Weber growth mode of the films. The CrxV1-x / MgO(001) system can serve as a model system to study both the fundamentals of defect formation in bcc films and the interplay between nanoscale defects such as dislocations and radiation damage.

36 MATERIALS SCIENCE↗

Probing Conformational Evolution and Associated Dynamics of Mg(N(SO 2 CF 3 ) 2 ) 2 ·Dimethoxyethane Adduct Using Solid-State 19 F and 1 H NMR

Bis(trifluoromethanesulfonimide) or TFSI is widely used as a counter anion in electrolyte design due to its structural flexibility and chemical stability. Here we studied the conformational variations and associated dynamics of TFSI in adduct of Mg(TFSI) 2 with dimethoxyethane (DME), a solvate crystalline material using solid-state 1 H and 19 F NMR. TFSI molecular motion in this solvate structure falls within the timescale of the 19 F NMR experiment, yielding spectroscopic signatures for unique TFSI conformers under the coordination environment of Mg 2+ cation. Within the temperature range of -5 to 82 °C, we observe nine distinct TFSI sites in both crystalline and disordered regions using 19 F NMR, reflecting complexity of structural and dynamics of TFS1 anions within solvate structure. The four distinguishable sites in the disordered region for the two CF 3 groups of the same TFSI molecule are identified using chemical shift analysis. The exchange rate constants from site to site are calculated through variable temperature 19 F NMR and two-dimensional (2D) exchange spectroscopy (EXSY) experiments, along with respective activation enthalpies using Eyring's formulation. The flip rate of CF 3 around the S-C bond is estimated as ~ 15 s -1 at 8 °C with ΔH ≠ ~ 22 kJ/mol, but the rotation of the entire TFSI is 4.8 s -1 at 8 °C with a significantly greater ΔH ≠ = 98 ± 10 kJ/mol. Furthermore, the slow conversion of trans to cis conformers at a lower temperature (T ≤ 1 °C) in the crystalline region is monitored, with a conversion rate of ~ 2 x 10 -5 s -1 at -5 °C. Density functional theory (DFT)-based calculations were performed to support further the assignment of experimental chemical shifts, and the activation energy E a = 21.1 kJ/mol obtained for the cis to trans transition is consistent with experimental values. The combined set of 19 F and 1 H under both one-dimensional (1D) and 2D NMR methods demonstrated here can be further used for examining electrode-electrolyte interfaces to probe the motions of various constituents that can enable detailed studies of interfacial processes and dynamics. Ultimately, such studies will aid in the design and discovery of interfacial constructs in which directed defect chemistry, chemical moiety distribution, and nanostructure are employed to drive efficient charge transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoscale Confinement of Photo-Injected Electrons at Hybrid Interfaces

A prerequisite for advancing hybrid solar light harvesting systems is a comprehensive understanding of the spatiotemporal dynamics of photoinduced interfacial charge separation. Here, we demonstrate access to this transient charge redistribution for a model hybrid system of nanoporous zinc oxide (ZnO) and ruthenium bipyridyl chromophores. The site-selective probing of the molecular electron donor and semiconductor acceptor by time-resolved X-ray photoemission provides direct insight into the depth distribution of the photoinjected electrons and their interaction with the local band structure on a nanometer length scale. Our results show that these electrons remain localized within less than 6 nm from the interface, due to enhanced downward band bending by the photoinjected charge carriers. This spatial confinement suggests that light-induced charge generation and transport in nanoscale ZnO photocatalytic devices proceeds predominantly within the defect-rich surface region, which may lead to enhanced surface recombination and explain their lower performance compared to titanium dioxide (TiO 2 )-based systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Size- and Phase-Controlled Nanometer-Thick ß-Ga2O3 Films with Green Photoluminescence for Optoelectronic Applications

Realization and optimization of the tunable/enhanced optical properties is critical to further advance the field of optoelectronics, photonics, and nano-electronics. In this context, here, we demonstrate green-emission characteristics with a ~30 fold enhancement in selectively engineered nanocrystalline Ga2O3 with a control over size, phase and interface nanostructure. Pulsed-laser-deposited ß-phase Ga2O3 films with an average crystallite size of ~9 nm along with a highly dense, close-compact nano-columnar structure with lowest possible defect density facilitates the thirty-fold enhancement in the photoluminescence (PL) intensity in green-region. Enhanced PL-emission in the optimized, engineered nano-architecture sheds light in designing Ga2O3-materials for promising future optoelectronic/photocatalytic applications.

Ga2O3, Nanocrystalline Films, Pulsed-Laser Deposit↗

Radiation damage in tungsten under high-energy He-ion irradiation

Tungsten (W) is a primary candidate for plasma-facing components (PFCs) in fusion reactors and hybrid fission-fusion reactors. However, W suffers from severe microstructural damage under Helium (He) ion irradiation in operation conditions. Key irradiation parameters, including incident ion energy, fluence, and irradiation temperature, are known to determine the formation of He bubbles and dislocation loops, which ultimately lead to the degradation of mechanical properties, such as radiation hardening and ductile-to-brittle transition temperature (DBTT) shifts. Various strategies, for instance, interface engineering and alloying, have been developed to enhance He irradiation tolerance in W to address these challenges. Studies in the recent two decades have enhanced the understanding of the underlying mechanisms that drive defect evolution and mechanical performance degradation, thereby offering more insights into the design of more resilient W-based materials for extreme environments.

Liu, Yinghang [Purdue University]↗

Consistency and reproducibility in atomic layer deposition

Atomic layer deposition (ALD) is a thin film synthesis technique that can provide exquisite accuracy and precision in film thickness and composition even on complex, large area substrates. Based on self-limiting surface chemistry, ALD can be insensitive to process conditions and reactor designs, allowing an ALD process developed in one lab to be easily reproduced in other labs. In practice, however, ALD is sometimes difficult to reproduce or replicate, and the results can vary substantially between ALD reactors and between labs. This is exemplified by large deviations in reports on the growth of, e.g., Al2O3, FeOx, and TiO2 given the same precursors under similar conditions. Furthermore, the problem of irreproducibility seems to be growing as ALD is adopted by more researchers and integrated into new applications. In this article, the authors highlight some of the major sources of variations and errors and common misconceptions related to ALD. In particular, the authors focus on issues related to precursors, substrates, and deposition tools. The authors illustrate these problems through examples from the literature, and they present results from numerical simulations that describe how nonidealities would manifest in thickness profiles in a typical cross-flow reactor. They also describe how reproducibility in ALD is linked to consistent experimental practice and reporting between labs. The authors’ hope is that by educating newcomers to ALD and advocating for consistent reporting of deposition conditions, they can minimize irreproducibility and enable ALD practitioners to realize the full potential afforded by self-limiting surface chemistry.

36 MATERIALS SCIENCE↗

Heterostructures for Increased Quantum Efficiency in Nitride LEDs

Task 1. Development of an advanced LED simulator useful for the design of efficient nitride-based devices. Simulator will contain graphical interface software that can be used to specify the device structure, the material parameters, the operating conditions and the desired output results. Task 2. Theoretical and experimental investigations regarding the influence on the microstructure, defect concentration, mechanical stress and strain and IQE of controlled changes in the chemistry and process route of deposition of the buffer layer underlying the active region of nitride-based blue- and greenemitting LEDs. Task 3. Theoretical and experimental investigations regarding the influence on the physical properties including polarization and IQE of controlled changes in the geometry, chemistry, defect density, and microstructure of components in the active region of nitride-based blue- and green-emitting LEDs. Task 4. Theoretical and experimental investigations regarding the influence on IQE of novel heterostructure designs to funnel carriers into the active region for enhanced recombination efficiency and elimination of diffusion beyond this region. Task 5. Theoretical and experimental investigations regarding the influence of enhanced p-type doping on the chemical, electrical, and microstructural characteristics of the acceptor-doped layers, the hole injection levels at Ohmic contacts, the specific contact resistivity and the IQE of nitride-based blue- and green-emitting LEDs. Development and optical and electrical characterization of reflective Ohmic contacts to n- and p-type GaN films.

14 SOLAR ENERGY↗

Raptor

Raptor is an efficient Python-based tool for predicting the formation and morphology of stochastic lack of fusion defects in metal AM processes. A major obstacle for the qualification and certification of additively manufactured parts in critical applications continues to be performance variability caused in part by porosity-related defects. High-fidelity process models that could predict these defect features are currently too computationally expensive for component-level analysis. To address this, Raptor employs a high-performance geometric method to model the dynamic melt pool rather than relying on computationally intensive thermal fluid dynamics. This allows Raptor to rapidly identify regions of unmelted material that correspond to lack of fusion pores. The efficiency of this approach significantly reduces the time and resources needed for generating 3D defect predictions, which enables users to conduct large-scale parameter studies and evaluate how process variations affect part quality. The framework offers operational flexibility; users can execute simulations through a simple command line interface or integrate core functions as a library within larger computational workflows. Simulation outputs include 3D porosity maps for visualization and tools for quantitative morphological analysis. These results are suitable for direct comparison with experimental characterization data from methods such as X-ray computed tomography and can be used for statistical process optimization.

Subraveti, Vamsi [Vanderbilt Univ., Nashville, TN ↗

Autonomic Materials for Smarter, Safer, Longer-Lasting Batteries (A "Life at the Frontiers of Energy Research" contest entry from the 2011 Energy Frontier Research Centers (EFRCs) Summit and Forum)

"Autonomic Materials for Smarter, Safer, Longer-Lasting Batteries" was submitted by the Center for Electrochemical Energy Science (CEES) to the "Life at the Frontiers of Energy Research" video contest at the 2011 Science for Our Nation's Energy Future: Energy Frontier Research Centers (EFRCs) Summit and Forum. Twenty-six EFRCs created short videos to highlight their mission and their work. CEES, an EFRC directed by Michael Thackery at Argonne National Laboratory is a partnership of scientists from four institutions: ANL (lead), Northwestern University, Purdue University, and the University of Illinois at Urbana-Champaign. The Office of Basic Energy Sciences in the U.S. Department of Energy's Office of Science established the 46 Energy Frontier Research Centers (EFRCs) in 2009. These collaboratively-organized centers conduct fundamental research focused on 'grand challenges' and use-inspired 'basic research needs' recently identified in major strategic planning efforts by the scientific community. The overall purpose is to accelerate scientific progress toward meeting the nation's critical energy challenges. The mission of the Center for Electrochemical Energy Science (CEES) is "to create a robust fundamental understanding of the phenomena that control the reactivity of electrified oxide interfaces, films and materials relevant to lithium-ion battery chemistries". Research topics are: electrical energy storage, batteries, battery electrodes, electrolytes, adaptive materials, interfacial characterization, matter by design; novel materials synthesis, charge transport, and defect tolerant materials.

25 ENERGY STORAGE↗

Li 2 OHCl crystalline electrolyte for stable metallic lithium anodes

In a classic example of stability from instability, we show that Li 2 OHCl solid electrolyte forms a stable solid electrolyte interface (SEI) with metallic lithium anode. The Li 2 OHCl solid electrolyte can be readily achieved through simple mixing of air-stable LiOH and LiCl precursors with a mild processing temperature under 400 °C. Additionally, we show that continuous, dense Li 2 OHCl membranes can be fabricated at temperatures less than 400 °C, standing in great contrast to current processing temperatures of over 1600 °C for most oxide-based solid electrolytes. The ionic conductivity and Arrhenius activation energy were explored for the LiOH-LiCl system of crystalline solid electrolytes where Li 2 OHCl with increased crystal defects was found to have the highest ionic conductivity and reasonable Arrhenius activation energy. The Li 2 OHCl solid electrolyte displays stability against metallic lithium, even in extreme conditions past the melting point of lithium metal. Furthermore, to understand this excellent stability, we show that SEI formation is critical in stabilizing the interface between metallic lithium and the Li 2 OHCl solid electrolyte.

36 MATERIALS SCIENCE↗

Electrochemically Induced High Capacity Displacement Reaction of PEO/MoS2/Graphene Nanocomposites with Lithium

MoS2/PEO/graphene composite is successfully prepared and the discharge mechanism of MoS2 as an anode material for Li-ion batteries has been investigated systematically in this work. The simultaneous formation of Li2S and Mo at deep discharge depth has been shown for the first time. The deposition of Mo metal with Li residing on the defects after the first discharge increases the intrinsic electronic conductivity of the electrode leading to a superior cycling stability for over 185 cycles. After the first discharge the amorphous Mo matrix allows a large amount of Li+ ions to repeatedly deposit and being oxidized during cycling while the transition between Li2S and S contribute to the capacity above 2.0 V. The interactions between as-formed Mo and S prevents the dissolution of the intermediate polysulfide thus providing clues to immobilize the soluble species in a Li-S battery. Excellent rate performances are achieved in this MoS2/PEO/graphene composite indicating a fast diffusion path of Li+ ions existing not only in the bulk material but also in the interface between the electrode and the electrolyte.

36 MATERIALS SCIENCE↗

Lattice distortion in single crystal rare-earth arsenide/GaAs nanocomposites

Epitaxial single crystal nanocomposites comprised of rare-earth arsenide nanoparticles embedded in GaAs (001) layers produce a larger change in lattice parameter than expected from the lattice parameters of relaxed films. Despite similar cubic structures and lattice parameters, elongation of the interfacial bond length between the two materials induces additional strain causing an expansion in the nanocomposite lattice. The interface bond length is material dependent with an average atomic layer spacing at the ErAs:GaAs interface of 1.9 Å while the spacing at the ScAs:GaAs interface is only 1.4 Å. Implications for lattice matching various single crystal epitaxial nanostructures in semiconductors are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of geometric, thermal and tunneling effects on nano-transistors

Electronic transistors are fundamental building blocks of large scale integrated circuits in modern advanced electronic equipments, and their sizes have been down-scaled to nanometers. Modeling and simulations in the framework of quantum dynamics have emerged as important tools to study functional characteristics of these nano-devices. This work explores the effects of geometric shapes of semiconductor–insulator interfaces, phonon–electron interactions, and quantum tunneling of three-dimensional (3D) nano-transistors. First, we propose a two-scale energy functional to describe the electron dynamics in a dielectric continuum of device material. Coupled governing equations, i.e., Poisson–Kohn–Sham (PKS) equations, are derived by the variational principle. Additionally, it is found that at a given channel cross section area and gate voltage, the geometry that has the smallest perimeter of the channel cross section offers the largest channel current, which indicates that ultra-thin nanotransistors may not be very efficient in practical applications. Moreover, we introduce a new method to evaluate quantum tunneling effects in nanotransistors without invoking the comparison of classical and quantum predictions. It is found that at a given channel cross section area and gate voltage, the geometry that has the smallest perimeter of the channel cross section has the smallest quantum tunneling ratio, which indicates that geometric defects can lead to higher geometric confinement and larger quantum tunneling effect. Furthermore, although an increase in the phonon–electron interaction strength reduces channel current, it does not have much impact to the quantum tunneling ratio. Finally, advanced numerical techniques, including second order elliptic interface methods, have been applied to ensure computational accuracy and reliability of the present PKS simulation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

1.5 MeV proton irradiation effects on electrical and structural properties of TiO{sub 2}/n-Si interface

In this paper, we report the effect of 1.5 MeV proton beam irradiation dose on the structural and electrical properties of TiO{sub 2} thin films deposited on n–Si substrates. The formation and transformation of different TiO{sub 2} phases in the irradiated thin films were characterized by X-ray diffraction and X-ray photoelectron spectroscopy (XPS). X-ray diffraction measurements revealed that the as grown film was rich in Ti{sub 5}O{sub 9} phase and then converted to mixed phases of TiO{sub 2} (rutile and anatase) after exposure with radiation doses up to 5 × 10{sup 14} cm{sup −2}. The XPS results revealed the formation of oxygen vacancy (negative) traps in the exposed TiO{sub 2} films, which showed strong dependence on the dose. The C-V measurements showed that proton radiations also damaged the Si substrate and created deep level defects in the substrate, which caused a shift of 0.26 ± 0.01 V in the flat band voltage (V{sub FB}). I–V measurements showed that the ideality factor increased and the rectification ratio dropped with the increase in the radiation dose. The present study showed the stability of TiO{sub 2}/Si interface and TiO{sub 2} film as an oxide layer against proton radiations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗