Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Thermal and mechanical properties of CeO 2

In this study, the thermal and mechanical properties of cerium dioxide (CeO 2 ) were assessed using a range of experimental techniques. The oxygen potential of CeO 2 was measured by the thermogravimetric technique, and a numerical fit for the oxygen potential of CeO 2 is derived based on defect chemistry. Mechanical properties of CeO 2 were obtained using sound velocity measurement, resonant ultrasound spectroscopy and nanoindentation. The obtained mechanical properties of CeO 2 are then used to evaluate the Debye temperature and Grüneisen constant. The heat capacity and thermal conductivity of CeO 2 were also calculated using the Debye temperature and the Grüneisen constant. Lastly, the thermal conductivity was calculated based upon laser flash analysis measurements performed on pellets fabricated using a range of feedstock purities to resolve discrepancies in the existing literature.

36 MATERIALS SCIENCE↗

Prediction of natural frequency variability due to uncertainty in material properties

Composite materials are widely used in various types of modern engineering structures. Traditional studies on composite structures have been based on the assumption that the material properties of the composites are characterized by a priori known elastic moduli, and no uncertainties of these moduli have been considered. However, the composite materials are invariably subject to a certain amount of scatter in their measured elastic moduli. To a large extent, the properties of composite materials are dependent on the fabrication process. But even the composite materials manufactured by the same process demonstrate differences in their elastic properties. This paper proposes a new, non-probabilistic method to predict the variability in the natural frequencies of the composite cylindrical shell, resulting from the unavoidable scatter in elastic moduli. The available measurements of elastic moduli are fitted by the four-dimensional uncertainty ellipsoid. The upper and lower bounds of the natural frequency are derived. With these bounds, designers will have a better understanding of the real dynamic behavior of the structure.

Li, Y. W.↗

Tailoring Nitinol for elastocaloric application

This study focuses on tailoring commercial Nitinol, the most commonly used elastocaloric material, for near-room-temperature cooling applications. Short heat treatments near 500 °C were used to fine-tune the material’s transition temperature, resulting in austenite finish temperatures ranging from 6.0 to 25.5°C and altered superelastic and elastocaloric properties. Plateau stresses decreased while temperature changes rose from 21.5°C up to 27.9°C at 6% strain. Significant variability in the Nitinol response when testing below its austenite finish temperature was observed. In conclusion, the effect of mechanical cycling on transition temperatures was also evaluated, demonstrating an increase for all the samples.

Efficiency↗

Aqueous Geochemistry at High Pressures and High Temperatures

This project is aimed at experimental characterization of the sound velocities, equations of state (EOS), and derived physical and chemical properties of aqueous solutions and carbon dioxide at extreme pressure and temperature conditions relevant to processes occurring in the interior of the Earth. Chemical transport, phase changes (including melting), fluid-solid reactions, and formation of magmatic liquids at convergent plat boundaries are a key motivation for this project. Research in this area has long been limited by the extreme experimental challenges and lack of data under the appropriate pressure-temperature (P-T) conditions. The vast majority of studies of aqueous geochemistry relevant to terrestrial problems of fluid-rock interactions have been conducted at 0.3 GPa or less, and the widely used Helgeson-Kirkham-Flowers equation of state for aqueous species is applicable only at ~ < 0.5 GPa. These limits are unfortunate because fluid flow and reactions plays a central role in many deeper environments. Recent efforts including our own, have resulted in new experimental techniques that now make it possible to investigate properties of homogeneous and heterogeneous equilibria involving aqueous species and minerals over a much broader range of pressure and temperature appropriate for deep crustal and upper mantle processes involving water-rich fluids. We carried out 1) Brillouin scattering measurements of the equations of state and molar volume of water and carbon dioxide to over 10 GPa and 870K using precise resistance heating of samples under pressure in the diamond anvil cell, and 2) the phase diagrams of the water and CO2, and 3) Exploring new experimental approaches, including CO2 laser heating of samples in a diamond cell, to measurements of sound velocities, EOS, and phase relations by Brillouin scattering to far greater pressures and temperatures.

58 GEOSCIENCES↗

Nanomechanical mapping and strain rate sensitivity of microcrystalline cellulose

Nanoindentation provides a convenient and high-throughput means for mapping mechanical properties and for measuring the strain rate sensitivity of a material. Here, nanoindentation was applied to the study of microcrystalline cellulose. Here, constant strain rate nanoindentation revealed a depth dependence of nanohardness and modulus, mostly attributed to material densification. Nanomechanical maps of storage modulus and hardness resolved the shape and size of voids present in larger particles. In smaller, denser particles, however, where storage modulus varied little spatially, there was still some spatial dependence of hardness, which can be explained by cellulose’s structural anisotropy. Additionally, hardness changed with the indentation strain rate in strain rate jump tests. The resulting strain rate sensitivity values were found to be in agreement with those obtained by other techniques in the literature.

36 MATERIALS SCIENCE↗

A Density Functional Theory Investigations of Half-Heusler Compounds RhVZ (Z = P, As, Sb)

We have studied the half-Heusler compounds RhVZ (Z = P, As, Sb) using Density Functional Theory (DFT). The method of the Full Potential Linearly Augmented Plane Wave (FP-LAPW) is employed in the Wien2k package for calculation of structural, elastic, mechanical, electronic, magnetic, and optical properties. Lattice constants are found in the range 5.67 − 5.80 Å. Analysis of elastic properties shows that two of the compounds namely RhVP and RhVAs are ductile while RhVSb is brittle in nature. All three compounds are half-metals as revealed from the band structures and Density of States (DoS) calculations. In all of them, spin-down channels have the small band gaps, while spin-up channels are conducting. These compounds follow the Slater-Pauling 18 (M{sub Tot} = Z{sub Tot} − 18) electron rule with the total magnetic moments in the range 1 − 2 μ{sub B}. Optical properties like dielectric function, refractive index, reflectivity, conductivity, and absorption coefficient are calculated and discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanical response and microprocesses of reconsolidating crushed salt at elevated temperature

Design, analysis and performance assessment of potential salt repositories for heat-generating nuclear waste require knowledge of thermal, mechanical, and fluid transport properties of reconsolidating granular salt. So, to inform salt repository evaluations, we have undertaken an experimental program to determine Bulk and Young’s moduli and Poisson’s ratio of reconsolidated granular salt as a function of porosity and temperature and to establish the deformational processes by which the salt reconsolidates. Our tests were conducted at 100, 175, and 250 °C. In hydrostatic tests, confining pressure is increased to 20 MPa with periodic unload/reload loops to determine K. Volume strain increases with increasing temperature. In shear tests at 2.5 and 5 MPa confining pressure, after confining pressure is applied, the crushed salt is subjected to a differential stress, with periodic unload/reload loops to determine E and ν. At predetermined differential stress levels the stress is held constant and the salt consolidates. Displacement gages mounted on the samples show little lateral deformation until the samples reach a porosity of ~10 %. Interestingly, vapor is vented only for 250 °C tests and condenses at the vent port. It is hypothesized that the brine originates from fluid inclusions, which were made accessible by heating and intragranular deformational processes including decrepitation. Furthermore, identification and documentation of consolidation processes are inferred from optical and scanning electron microstructural observations. As a result, densification at low porosity is enhanced by water film on grain boundaries that enables solution-precipitation phenomena.

58 GEOSCIENCES↗

Abelian anomaly and neutral pion production

We show that in fully self-consistent treatments of the pion, namely, its static properties and elastic and transition form factors, the asymptotic limit of the product Q{sup 2}G{sub {gamma}}{sup *}{sub {gamma}{pi}}{sup 0}(Q{sup 2}), determined a priori by the interaction employed, is not exceeded at any finite value of spacelike momentum transfer. Furthermore, in such a treatment of a vector-vector contact-interaction one obtains a {gamma}{sup *{gamma}{yields}{pi}0} transition form factor that disagrees markedly with all available data. We explain that the contact interaction produces a pion distribution amplitude that is flat and nonvanishing at the endpoints. This amplitude characterizes a pointlike pion bound state. Such a state has the hardest possible form factors (i.e., form factors that become constant at large momentum transfers and hence are in striking disagreement with completed experiments). However, interactions with QCD-like behavior produce soft pions, a valence-quark distribution amplitude that vanishes as {approx}(1-x){sup 2} for x{approx}1, and results that agree with the bulk of existing data. Our analysis supports a view that the large-Q{sup 2} data obtained by the BaBar Collaboration is not an accurate measure of the {gamma}*{gamma}{yields}{pi}{sup 0} form factor.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Extending the capillary wave model to include the effect of bending rigidity: X-ray reflectivity and diffuse scattering

The surface roughness of a thin film at a liquid interface exhibits contributions of thermally excited fluctuations. This thermal roughness depends on temperature (𝑇), surface tension (𝛾), and elastic material properties, specifically the bending modulus (𝜅) of the film. A nonzero 𝜅 suppresses the thermal roughness at small length scales compared to an interface with zero 𝜅, as expressed by the power spectral density of the thermal roughness. The description of the x-ray scattering of the standard capillary wave model (CWM), which is valid for zero 𝜅, is extended to include the effect of 𝜅. The extended CWM (eCWM) provides a single analytical form for both the specular x-ray reflectivity (XRR) and the diffuse scattering around the specular reflection, and recovers the expression of the CWM at its zero 𝜅 limit. This theoretical approach enables the use of single-shot grazing incidence x-ray off-specular scattering (GIXOS) measurements for characterizing the structure of thin films on a liquid surface. The eCWM analysis approach decouples the thermal roughness factor from the surface scattering signal, providing direct access to the intrinsic surface-normal structure of the film and its bending modulus. Moreover, the eCWM facilitates the calculation of reflectivity at any desired resolution (pseudo-XRR approach). The transformation into pseudo-XRR provides the benefit of using widely available XRR software to perform GIXOS analysis. The extended range of the vertical scattering vector (𝑄 𝑧 ) available with the GIXOS pseudo-XRR approach allows for a higher spatial resolution than with conventional XRR. Experimental results are presented for various lipid systems, showing strong agreement between conventional specular XRR and pseudo-XRR methods. This agreement validates the proposed approach and highlights its utility for analyzing soft, thin films.

36 MATERIALS SCIENCE↗

Resonant Ultrasound Spectroscopy studies of Berea sandstone at high temperature

Resonant Ultrasound Spectroscopy was used in this paper to determine the elastic moduli of Berea sandstone from room temperature to 478 K. Sandstone is a common component of oil reservoirs, and the temperature range was chosen to be representative of typical downhole conditions, down to about 8 km. In agreement with previous works, Berea sandstone was found to be relatively soft with a bulk modulus of approximately 6 GPa as compared to 37.5 GPa for α-quartz at room temperature and pressure. Finally, it was found that Berea sandstone undergoes a ~17% softening in bulk modulus between room temperature and 385 K, followed by an abnormal behavior of similar stiffening between 385 K and 478 K.

58 GEOSCIENCES↗

Elastic wave velocity evolution of shales deformed under uppermost crustal conditions

In this paper, conventional triaxial tests were performed on a series of samples of Tournemire shale along different orientations relative to bedding (0°, 90°). Experiments were carried out up to failure at increasing confining pressures ranging from 2.5 to 80 MPa, and at strain rates ranging between 3 × 10 -7 s -1 and 3 × 10 -5 s -1 . During each experiment, P and S wave elastic velocities were continuously measured along many raypaths with different orientations with respect to bedding and maximum compressive stress. This extensive velocity measurement setup allowed us to highlight the presence of plastic mechanisms such as mineral reorientation during deformation. The evolution of elastic anisotropy was quantified using Thomsen's parameters which were directly inverted from measurement of elastic wave velocity. Brittle failure was preceded by a change in P wave anisotropy, due to both crack growth and mineral reorientation. Anisotropy variations were largest for samples deformed perpendicular to bedding, at the onset of rupture. Anisotropy reversal was observed at the highest confining pressures. For samples deformed parallel to bedding, the P wave anisotropy change is weaker.

58 GEOSCIENCES↗

Dissimilar Material Joining via Interlocking Metasurfaces

Background The integration of dissimilar materials poses a significant challenge in engineering, necessitating innovative solutions for robust and reliable joining. Interlocking metasurfaces (ILMs) are a new joining technology comprising arrays of autogenous features patterned across two surfaces that interlock to form robust structural joints. Objective Here, this study elucidates the factors influencing the tensile performance of ILM joints formed between dissimilar materials. Methods We employed parametric optimization to identify optimal unit cell geometries for maximal yield strength based on the hypothesis that the elastic tensile properties of the materials are the primary determinants of tensile performance. Experimental validation was performed by mechanically testing the theorized optimal ILM geometry and a range of ILM geometries to capture the overall behavior trends of joints between two additively manufactured polymers, VeroPureWhite (VW) and RGDA8430-DM (8430). Results Experimental validation of optimized designs revealed that additional factors, e.g. flexural strength and localized plasticity, also strongly influenced the tensile performance of T-slot ILMs joining dissimilar materials. The proposed optimal design remained the best performer. Conclusions This study demonstrates the viability of ILMs as a joining method for dissimilar materials. ILMs can join dissimilar materials with no loss in joint yield strength compared to joints composed solely of the weaker of the two constitutive materials. ILMs demonstrated their potential as a versatile and effective joining technology in diverse engineering applications.

Elbrecht, Benjamin James [Sandia National Laborato↗

Effect of Topology on Transient Dynamic and Shock Response of Polymeric Lattice Structures

Architected cellular materials, such as lattice structures, offer potential for tunable mechanical properties for dynamic applications of energy absorption and impact mitigation. In this work, the static and dynamic behavior of polymeric lattice structures was investigated through experiments on octet-truss, Kelvin, and cubic topologies with relative densities around 8%. Here, dynamic testing was conducted via direct impact experiments (25–70 m/s) with high-speed imaging coupled with digital image correlation and a polycarbonate Hopkinson pressure bar. Mechanical properties such as elastic wave speed, deformation modes, failure properties, particle velocities, and stress histories were extracted from experimental results. At low impact velocities, a transient dynamic response was observed which was composed of a compaction front initiating at the impact surface and additional deformation bands whose characteristics matched low strain-rate behavior. For higher impact velocities, shock analysis was carried out using compaction wave velocity and Eulerian Rankine–Hugoniot jump conditions with parameters determined from full-field measurements.

36 MATERIALS SCIENCE↗

Optimization of a hybrid exchange-correlation functional for silicon carbides

A hybrid exchange-correlation functional is optimized in order to accurately describe the nature of silicon carbides (SiC) in the framework of ab-initio calculations based on density functional theory (DFT), especially with an aim toward future applications in defect studies. It is shown that the Heyd-Scuseria-Ernzerhof (HSE) hybrid functional with the screening parameter of 0.15 -1 outperforms conventional exchange-correlation functionals and other popular hybrid functionals regarding description of band structures in SiC. High transferability is proven through assessment over various SiC polytypes, silicon and diamond. Excellent performance is also confirmed for other fundamental material properties including elastic constants and phonon frequency.

Defects↗

A rock physics and seismic reservoir characterization study of the Rock Springs Uplift, a carbon dioxide sequestration site in Southwestern Wyoming

We present a reservoir geophysics study, including rock physics modeling and seismic inversion, of a carbon dioxide sequestration site in Southwestern Wyoming, namely the Rock Springs Uplift, and build a petrophysical model for the potential injection reservoirs for carbon dioxide sequestration. Our objectives include the facies classification and the estimation of the spatial model of porosity and permeability for two sequestration targets of interest, the Madison Limestone and the Weber Sandstone. The available dataset includes a complete set of well logs at the location of the borehole available in the area, a set of 110 core samples, and a seismic survey acquired in the area around the well. The proposed study includes a formation evaluation analysis and facies classification at the well location, the calibration of a rock physics model to link petrophysical properties and elastic attributes using well log data and core samples, the elastic inversion of the pre-stack seismic data, and the estimation of the reservoir model of facies, porosity and permeability conditioned by seismic inverted elastic attributes and well log data. In particular, the rock physics relations are facies-dependent and include granular media equations for clean and shaley sandstone, and inclusion models for the dolomitized limestone. The permeability model has been computed by applying a facies-dependent porosity-permeability relation calibrated using core sample measurements. Finally, the study shows that both formations show good storage capabilities. The Madison Limestone includes a homogeneous layer of high-porosity high-permeability dolomite; the Weber Sandstone is characterized by a lower average porosity but the layer is thicker than the Madison Limestone.

58 GEOSCIENCES↗

Anomalous elastic behavior of tantalum at high pressures: Experimental and theoretical studies

Elastic wave velocities of polycrystalline tantalum have been measured up to 13.6 GPa at room temperature using ultrasonic interferometry technique in a multi-anvil apparatus. The bulk and shear moduli, as well as their pressure derivatives are obtained using Eulerian 3rd order finite strain equations, yielding K S0 = 193.9(29) GPa, G 0 = 69.3(10) GPa, K S0' = 3.18(5) and G 0' = 0.88(1). Here the Steinberg-Guinan yield stress model is examined using the current shear modulus and its pressure derivative, where a slightly lower A 0 = 0.0127 GPa –1 compared to previous studies is obtained. First-principles calculations on the elasticity of tantalum have also been performed up to 200 GPa. Anomalous softening of the elastic shear constant C 44 and shear wave velocity V S is observed between 80– 180 GPa, whereas the anisotropy shows a softening-stiffening behavior with increasing pressure and reaches a minimum at around 150 GPa. Such anomalies might commonly originate from the nesting of Fermi surface for Group VB metals.

36 MATERIALS SCIENCE↗

Polycrystalline elastic moduli of a high-entropy alloy at cryogenic temperatures

A FCC high-entropy alloy (HEA) that exhibits strong temperature dependence of strength at low homologous temperatures in sharp contrast to pure FCC metals like Ni that show weak temperature dependence is CrMnCoFeNi. In order to understand this behavior, elastic constants were determined as a function of temperature. From 300 K down to 55 K, the shear modulus (G) of the HEA changes by only 8%, increasing from 80 to 86 GPa. Moreover, this temperature dependence is weaker than that of FCC Ni, whose G increases by 12% (81–91 GPa). Therefore, the uncharacteristic temperature-dependence of the strength of the HEA is not due to the temperature dependence of its shear modulus.

36 MATERIALS SCIENCE↗