Results for “layup” — Page 6

NASA NTRS2019

Design and Analysis of a Tool for Automated Fiber Placement of Composite Wind Tunnel Blades

For decades, composite wind tunnel blades have been constructed using labor-intensive hand layup processes. Automated Fiber Placement (AFP) is a relatively new technology that has not seen widespread use in manufacturing composite wind tunnel blades. AFP offers the potential for reduced manufacturing time, reduced cost, and improved consistency compared to traditional hand layup procedures. These manufacturing qualities are becoming increasingly important as existing wind tunnel blades are replaced due to impact damage or wear and tear from decades of use. Researchers at the NASA Langley Research Center are currently using the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to investigate the feasibility of AFP for manufacturing composite wind tunnel blades. ISAAC uses manufacturing tools as surfaces on which to place fiber tows. A manufacturing tool was developed for using AFP to build a wind tunnel blade shape. This paper presents the structural design and analysis of this tool, for use with AFP, constructed from high temperature thermoplastics. The tool fabricated by this design process was successfully used for AFP and oven cure of two representative airfoil shaped composite structures.

Brian Mason↗

NASA NTRS2020

Mechanics-Based Modeling Approach for Rapid Prediction of Low Velocity Impact Damage in Composite Laminates

A mechanics-based modeling approach is developed to rapidly predict damage in polymer matrix composites resulting from a low velocity impact event. The approach is incorporated into a computer code that provides an efficient means to assess the damage resistance for a range of material systems, layup configurations, and impact scenarios. It is envisioned that the developed approach will aid in early design and analysis of composite structures where sizing and layup decisions must be made, and evaluating the feasibility of a large number of laminate configurations using numerical approaches such as finite element analysis (FEA) is prohibitively expensive. Therefore, the goal of the modeling approach is to predict the impact damage size given the laminate configuration and impact scenario. This information can then be used to determine the residual strength of the material. To be useful in such a context, the tool is designed to run quickly (<2 minutes) to allow a large number of design cases to be investigated. The results presented demonstrate that the model is capable of efficiently predicting low velocity impact damage size, shape, and location within an acceptable accuracy suitable for preliminary design and analysis of composite structures.

Borkowski, Luke↗

NASA NTRS2012

TPSAS-NF1676L-13555-DND

A sub-scale advanced composite shell design is evaluated to determine its potential for use on a future aircraft fuselage. Two composite shells with the same nominal 8-ply [?45/?]s layup are evaluated, where ? indicates a tow-steered ply. To build this shell, a fiber placement machine is used to steer unidirectional prepreg tows as they are placed around the circumference of a 17-inch diameter right circular cylinder. The fiber orientation angle varies continuously from 10 degrees (with respect to the shell axis of revolution) at the crown, to 45 degrees on the side, and back to 10 degrees on the keel. All 24 tows are placed at each point on every fiber path in one structure designated as the shell with overlaps. The resulting pattern of tow overlaps causes the laminate thickness to vary between 8 and 16 plies. The second shell without tow overlaps uses the capability of the fiber placement machine to cut and add tows at any point along the fiber paths to fabricate a shell with a nearly uniform 8-ply laminate thickness. Static stiffness and buckling loads of shells with tow-steered layups are compared with the performance of a baseline quasi-isotropic shell using both finite element analyses and classical strength of materials theory. These tailored, tow-steered shells were then were designed and built at the National Center for Advanced Manufacturing - Louisiana Partnership under a joint NASA-industry collaborative effort. The shells were fabricated from unidirectional IM7/8552 graphite-epoxy pre-preg slit tape material placed on a constant-diameter mandrel. An overview of the detailed design and manufacturing processes for these shells is presented, and issues encountered during their design, analysis, fabrication and post-cure evaluation are presented and discussed. Future plans for structural testing and analyses of the shells are also discussed.

K Chauncey Wu↗

NASA NTRSDate not supplied

RESIDUAL DEFORMATION ANALYSIS IN COMPOSITE SHELL STRUCTURES MANUFACTURED USING AUTOMATED FIBER PLACEMENT

The manufacturing of composites typically produces residual stresses that can significantly affect the final shape of the structure. The process of automated fiber placement (AFP) has become a prominent manufacturing technique in developing layups with tailored, variable stiffness morphology. The steered patterns of fiber tows with and without overlaps produce residual deformations that are distinctive from traditional layups. Digital image correlation was used to measure the AFP lamina coefficients of thermal expansion, which were incorporated into finite element analyses (FEA) to model the cooling phase of the cure cycle. The effects of nonlinear analysis and temperature-dependent lamina properties calculated using self-consistent field micromechanics, on the resulting residual deformation of shells, were also modeled. The predicted residual deformation was analyzed by considering out-of-roundness in cylindrical shells and compared to the experimental results. The shell FEA results were well-correlated with the overall deformed shape of the AFP cylinder with overlaps, while the shell FEA model of the AFP cylinder without overlaps did not show as good of qualitative match of the deformation pattern. Analytical correlation with measured results were insensitive to material softening at elevated temperatures, geometric nonlinearities, and variations in measured lamina thermal properties. To improve the accuracy of the residual deformation analysis, these results suggest that the thermo-chemical shrinkages preceding the cooldown should be considered, as well as possible variations in ply level microstructure due to the presence of the embedded fiber tow gaps and overlaps.

Composites↗

NASA NTRS1995

Test-Derived Effective Emittance for Cassini MLI Blankets and Heat Loss Characteristics in the Vicinity of Seams

Multilayer insulation (MLI) blankets on the Cassini spacecraft will experience temperatures in the wide range of -200 to 360°C. Besides reducing heat loss, the MLI blankets will also serve, with standoffs, the purpose of micrometeoroid protection. Four major blanket layup configurations ??will be utilized on Cassini. Since definitive thermal properties for these layups were not available, thermal vacuum tests were conducted for their determination.

multilayer↗

NASA NTRSDate not supplied

Bistable Deployable Composite Booms With Parabolic Cross-Sections

This paper investigates how stable equilibrium states in the extended and coiled configurations can be predicted in thin-shelled composite booms with parabolic cross-sections. These conic shapes potentially offer greater stiffness properties when compared to circular cross-sections, which is critical for improving the load bearing performance of deployed booms. Inducing bistability through the choice of composite shell layups in parabolic booms would allow for controllable self-deployment due to a less energetic coiled state when compared to monostable booms. An inextensional analytical model is used to predict the stable coiled diameters of tape spring and Collapsible Tubular Mast (CTM) booms with parabolic cross-sections. The parabolic section is discretized into circular segments using biarc spline interpolation, which allows them to be integrated into the strain energy minimization procedure used to obtain the equilibrium states. When the parabolic booms are parametrically compared against circular booms with identical layups, flattened height, and mass, the former are found to generally have better stiffness performance while being less efficient in stowed volume as evidenced by larger coiled diameters. Analytical coiled diameters and their strain energy are verified with finite element simulations for optimal parabolic tape spring and CTM booms.

Andrew J. Lee↗

NASA NTRS2023

Exploration Extra-Vehicular Mobility Unit (xEMU) Composite Hard Upper Torso (CHUT) Development

The xEMU is the Exploration Mobility Unity or space suit designed for microgravity (cislunar and low earth orbit (LEO)) and lunar surface operations. This suit design allows crewmembers to perform extravehicular exploration, science, construction, maintenance, and contingency operations while unattached to a vehicle for life support in pressure and thermal environments that exceed human capability. The xEMU provides life support, environmental protection, and communications capabilities to the EVA crewmember while allowing sufficient mobility and visibility to perform dexterous EVA tasks. The effort documented in this paper, addressed the design, analysis, manufacturing, full-scale test article testing and validation for a Composite Hard Upper Torso(CHUT)unit. Design and analysis of the CHUT was based on measured B-basis properties of the selected S-glass/epoxy composite, and established final geometry, composite layup and interface details that met requirements. A complete manufacturing and assembly protocol was established for the CHUT starting from composite layup in the tool, to final assembly of all interface metal hardware prior to delivery to NASA for suit integration. Full-scale CHUT test articles underwent static and fatigue pressure testing (2 lifetimes), impact testing at critical stress locations for tool drop/microgravity scenarios, followed by post-impact fatigue testing. Effect of manufacturing defects was evaluated by manufacturing a full-scale CHUT with 0.375”/0.5” defects at critical stress locations, followed by static and life-cycle fatigue testing. In all cases, the CHUT design met or exceeded mass, structural, interface and functional requirements. Two (2) complete CHUT articles were delivered to NASA for full-scale suit integration and testing.

spacesuit↗

NASA NTRSDate not supplied

Implementation of Combinatorial Optimization Techniques for Automated Fiber Placement Through Thickness Defect Stack-Up Minimization

The Computer Aided Process Planning (CAPP) module was developed to facilitate and accelerate the process planning workflow for Automated Fiber Placement (AFP). CAPP assists process planners in identifying optimal starting point locations and layup strategies for each ply of a laminate. Ply optimization operates on measurement and scoring of geometry-based defects such as gaps, overlaps, angle deviation, and steering. This paper expands on the established framework for analyzing defect stack-up through thickness of a laminate. Four different combinatorial optimization algorithms are implemented and evaluated: (1) genetic algorithm, (2) differential evolution, (3) particle swarm, and (4) greedy search. The algorithms identify the optimal combination of ply-level layup strategies, by scoring potential laminates on defect stacking, using two different objective functions. A final optimization approach is also presented which trades some performance for a large gain in efficiency. These approaches are compared to a randomized combination using a complex tool surface in a virtual case study. The result is a streamlined methodology for comparing different laminate-level manufacturing strategies and minimizing the through thickness defect stack up.

CAPP↗

NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗

NASA NTRSDate not supplied

Process Development and Testing for Lunar Habitats

Non-metallic solutions for Lunar bases are appealing due to their light weight and ability to block many forms of radiation. Composite materials made from different combinations of these non-metallic materials enable effective mating of dissimilar materials for strong structures such as pressurized habitats. Inserting and manufacturing composite structural materials on the Moon presents several challenges, however: the oxygen levels inside pressurized habitats will be relatively high, radiation that is blocked causes damage and the lack of atmosphere results in a high-magnitude negative pressure environment. In the past two years, the Materials and Processes Lab (EM01) invested in two internal research and development (IRAD) proposals for testing and procurement of composite materials. One proposal endeavors to determine flammability and radiation damage of various composite materials with a focus on carbon fiber and ultra-high molecular weight polyethylene (UHWMPE). The other proposal enables procurement of chopped fiber spray equipment materials which will be used to develop a novel technique for chopped UHMWPE fiber layup, similar to the chopped fiberglass layups used for making large structures such a boat hulls and hot tubs.

Composite↗

NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗

NASA NTRS2023

Composite Hard Upper Torso (CHUT) for xEMU Space Suit

The xEMU is the Exploration Mobility Unity or space suit designed for microgravity (cislunar and low earth orbit (LEO)) and lunar surface operations. This suit design allows crewmembers to perform extravehicular exploration, science, construction, maintenance, and contingency operations while unattached to a vehicle for life support in pressure and thermal environments that exceed human capability. The xEMU provides life support, environmental protection, and communications capabilities to the EVA crewmember while allowing sufficient mobility and visibility to perform dexterous EVA tasks. The effort documented in this paper, addressed the design, analysis, manufacturing, full-scale test article testing and validation for a Composite Hard Upper Torso(CHUT)unit. Design and analysis of the CHUT was based on measured B-basis properties of the selected S-glass/epoxy composite, and established final geometry, composite layup and interface details that met requirements. A complete manufacturing and assembly protocol was established for the CHUT starting from composite layup in the tool, to final assembly of all interface metal hardware prior to delivery to NASA for suit integration. Full-scale CHUT test articles underwent static and fatigue pressure testing (2 lifetimes), impact testing at critical stress locations for tool drop/microgravity scenarios, followed by post-impact fatigue testing. Effect of manufacturing defects was evaluated by manufacturing a full-scale CHUT with 0.375”/0.5” defects at critical stress locations, followed by static and life-cycle fatigue testing. In all cases, the CHUT design met or exceeded mass, structural, interface and functional requirements. Two (2) complete CHUT articles were delivered to NASA for full-scale suit integration and testing.

spacesuit↗

NASA NTRS2023

Automated Fiber Placement Through Thickness Defect Stacking Optimization

In its 2022 commercial market outlook, Boeing forecasted an 80% increase in the global fleet through 2041 compared to 2019 pre-pandemic levels. This sharp rise in demand will drive pressure onto airframe manufacturers to ramp up production and find more efficient ways to design and manufacture airplanes. Complicating this challenge is the industry’s recent transformation from traditional metal-based airframes towards hybrid composite-metal aircraft. While composites have been used in aviation for decades, aircraft manufacturers are still struggling to design and manufacture quality parts at a high rate. Automated Fiber Placement (AFP) is one of the main manufacturing techniques used to produce large-scale composite parts. After a design has been created, a manufacturing strategy has to be developed based on the working material, part geometry, and machine capabilities. This process planning stage is essential to the AFP workflow and currently requires a high level of manual input from an experienced process planner. In an effort to automate and optimize this stage, the Computer Aided Process Planning (CAPP) module was developed. CAPP assists process planners in identifying optimal starting point location and layup strategy for each ply of a laminate. This Ply-Level Optimization (PLO) phase operates on the quantification of ply quality through predictable geometry-based defects such as gaps, overlaps, angle deviation, and steering. As you move from PLO to Laminate-Level Optimization (LLO) the design space grows exponentially, emphasizing the need for automated optimization. The work presented in this thesis expands CAPP’s functionality by comparing the planned fiber paths through the thickness of the laminate to mitigate stacked area defects and achieve an optimal laminate-level manufacturing strategy. Within CAPP, predicted gap and overlap defects are imported from Vericut Composites Programming (VCP) and then discretized to streamline the through-thickness comparison. Two objective functions are used to score different combinations of ply layup strategies based on defect stacking both globally and locally. Four combinatorial optimization algorithms were coupled with these objective functions to investigate the laminate-level manufacturing strategy design space and converge on the optimal plan. These algorithms were evaluated based on accuracy and efficiency through virtual testing on a complex tool surface. A separate LLO approach was developed to achieve near-optimal laminates in significantly less time. The end result is a software package which greatly reduces the required input from process planners, shortening the design-build cycle time and improving part quality.

AFP↗

NASA NTRSDate not supplied

Detection and Localization of a Fold, Twist, and Overlaps within Tow-Steered Composite Panels During Autoclave Cure

Because of the anisotropic properties of carbon fiber reinforced polymer (CRFP) composites, novel layup architectures, such as tow-steering, can be used to tailor mechanical properties of the composite structure to the loading condition during use. In this work, a tow-steered composite panel was de-signed, laid up using the Integrated Structural Assembly of Advanced Com-posites (ISAAC) automated fiber placement (AFP) machine located at the NASA Langley Research Center (LaRC), and cured while simultaneously be-ing inspected using an ultrasonic inspection system operating inside the auto-clave. The composite panel contained overlaps that are intrinsic to the tow-steered design and had intentionally introduced layup defects including folds, wrinkles, splices, tow twists, foreign object debris (FOD), gaps, and additional overlaps. The inspections during the cure cycle focused on the ar-ea within the laminate containing a fold, a twist, and intrinsic overlaps. The ultrasonic inspections performed during the cure cycle were analyzed and compared to post-cure ultrasonic inspections of the entire laminate.

Composites↗

NASA NTRSDate not supplied

Detection and Localization of a Fold, Twist, and Overlaps within Tow-Steered Composite Panels During Autoclave Cure

Because of the anisotropic properties of carbon fiber reinforced polymer (CRFP) composites, novel layup architectures, such as tow-steering, can be used to tailor mechanical properties of the composite structure to the loading condition during use. In this work, a tow-steered composite panel was de-signed, laid up using the Integrated Structural Assembly of Advanced Com-posites (ISAAC) automated fiber placement (AFP) machine located at the NASA Langley Research Center (LaRC), and cured while simultaneously be-ing inspected using an ultrasonic inspection system operating inside the auto-clave. The composite panel contained overlaps that are intrinsic to the tow-steered design and had intentionally introduced layup defects including folds, wrinkles, splices, tow twists, foreign object debris (FOD), gaps, and additional overlaps. The inspections during the cure cycle focused on the ar-ea within the laminate containing a fold, a twist, and intrinsic overlaps. The ultrasonic inspections performed during the cure cycle were analyzed and compared to post-cure ultrasonic inspections of the entire laminate.

Composites↗

NASA NTRSDate not supplied

Process Development and Testing for Lunar Habitats

Non-metallic composites are appealing for Lunar habitats due to their low specific weight and contribution to passive radiation shielding. This application of composite materials presents notable challenges, however: flammability risks are higher due to elevated oxygen levels expected in habitat structures and absorbed radiation can cause damage long-term. The Materials and Processes Laboratory at Marshall Space Flight Center awarded funding for an internal research and development study which included fabrication and testing of composite materials for Lunar habitats. Composite layups used carbon fiber or ultra-high molecular weight polyethylene reinforcement and a variety of polymer matrices. Pre-impregnated fabric was autoclave cured; however, novel coatings were incorporated during select layups. Samples from each panel were used for screening-level flammability testing (ASTM D 2863) and combined vacuum ultraviolet and electron irradiation followed by tension testing (ASTM D5766). Two of the tested composite materials exceeded a 37% limiting oxygen index. Material property degradation for a 10 year simulated radiation dose was minimal in most cases.

manufacturing↗

NASA NTRSDate not supplied

Flammability Test Method for Materials Intended for Use as Fire Barriers in Crewed Habitats

In some crewed-spacecraft applications, onboard materials are intentionally selected to function as hazard control barriers to prevent powered hardware and/or ignited flammable items from igniting nearby flammable materials by acting as non-breaching, non-flammable containment (e.g., cargo transfer bags, zero gravity stowage racks, and jettison stowage bags on the International Space Station). Historically, flammability self-extinguishment testing of broad acreage or outermost layer materials alone was believed to be sufficient to verify overall flammability compliance. Though required, testing on design features such as threaded seams and zippers was not performed due to the incorrect assumption that flammability performance would not be impacted. However, recent coupon level testing of layups and configurations consisting of multiple materials have revealed that these features may be more susceptible to ignition and fire propagation than the bulk material. Additionally, configurational coupon ignition and propagation testing does not explicitly determine a material’s ability to provide protection to vulnerable flammable hardware. The need to evaluate this gap in assessing material or layup effectiveness as fire barriers between ignition sources and flammable materials led to the development of a new configuration-based fire barrier test. Test setup, relevant configurations, and test validation are discussed. The new barrier test method establishes a configuration for the test apparatus, identifies a conservative ignitor configuration, and defines pass/fail criteria. Test setup, relevant configurations, and test validation are discussed.

Susana Harper↗

DOE OSTI2020

Challenges and Solutions in Operation and Lay-Up of the Modular Caustic- Side Solvent Extraction Unit - 20078

The Modular Caustic-Side Solvent Extraction (CSSX) Unit (MCU) was designed and constructed to provide interim salt waste processing so that the Liquid Waste Disposition Program (LWDP) could continue waste removal and tank closure until start-up of the Salt Waste Processing Facility (SWPF). MCU processes Clarified Salt Solution (CSS), or salt solution (SS) that has undergone actinide removal/filtration, to produce two waste streams: the cesium laden Strip Effluent (SE), which is incorporated into glass at the Defense Waste Processing Facility (DWPF), and the cesium depleted Decontaminated SS (DSS), which is incorporated into grout at the Saltstone Production Facility (SPF). MCU completed start-up in 2008 with an initial operating life of 3 years and design life of 5 years. Prior to reaching the end of the design life, multiple critical components were upgraded and/or replaced to mitigate risks associated with any delays in SWPF start-up. During the remainder of operation (until June 2019), MCU was challenged to maximize processing with minimal additional modifications to repair/improve aging infrastructure, while maintaining low levels of risk to workers and the environment. Notable challenges during the extended operating life of the facility involved both mechanical and operational issues. Two of the most significant issues were the increased frequency of Process Vessel Ventilation (PVV) High Efficiency Particulate Air (HEPA) filter change-outs and the biofouling of the SE coalescer (SEC). The major impacts of both issues were that replacement of these components 1) resulted in high exposure to workers, and 2) required substantial downtime, thus hindering achievement of processing goals. PVV HEPA filter replacements are required based on dose rate and differential pressure (dP) limits. After introducing a higher-curie feed to MCU, the operating time between change outs was reduced by approximately half. SEC replacements are required based on dP limits. After restarting from an extended outage, the operating life of the SEC was significantly reduced by more than half due to biofouling. As a result of extensive troubleshooting and process improvements, the facility was able to recover performance and extend the operating life of the PVV HEPA filters and the SEC media. Through troubleshooting both of these issues, the facility was also able to learn from prior experience and adapt in order to minimize down time and maintain throughput. Although the facility took advantage of short periods of downtime to perform nonintrusive troubleshooting and minor corrective/preventative maintenance activities, longer outages were periodically required for corrective maintenance involving process cell entry. During these outages, remote tools and specialized shield plates were employed to minimize dose to workers. Mock-ups of non-routine maintenance activities were critical to early identification of potential issues and improvements, which shortened outage duration. Consistent with the facility's operational strategy, evolutions needed for MCU layup were identified and sequenced to ensure safe conditions within the facility, meet pre-defined criteria for lay-up configuration, and protect workers, while minimizing the impact to SWPF integration. De-inventory and flushing of process areas was prioritized so that the total residual inventory was reduced as efficiently as possible. This paper discusses lessons learned and best practices from troubleshooting unique issues, performing complex maintenance activities, and implementing a layup strategy that best supports the overall system mission. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗