Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material type”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Quiet engine program: Turbine noise suppression. -Volume 1: General treatment evaluation and measurement techniques

Acoustic treatment was developed for jet engine turbine noise suppression. Acoustic impedance and duct transmission loss measurements were made for various suppression systems. An environmental compatibility study on several material types having suppression characteristics is presented. Two sets of engine hardware were designed and are described along with engine test results which include probe, farfield, near field, and acoustic directional array data. Comparisons of the expected and the measured suppression levels are given as well as a discussion of test results and design techniques.

Clemons, A.↗
NASA NTRS1975

Analytic and experimental evaluation of flowing air test conditions for selected metallics in a shuttle TPS application

A detailed experimental and analytical evaluation was performed to define the response of TD nickel chromium alloy (20 percent chromium) and coated columbium (R512E on CB-752 and VH-109 on WC129Y) to shuttle orbiter reentry heating. Flight conditions important to the response of these thermal protection system (TPS) materials were calculated, and test conditions appropriate to simulation of these flight conditions in flowing air ground test facilities were defined. The response characteristics of these metallics were then evaluated for the flight and representative ground test conditions by analytical techniques employing appropriate thermochemical and thermal response computer codes and by experimental techniques employing an arc heater flowing air test facility and flat face stagnation point and wedge test models. These results were analyzed to define the ground test requirements to obtain valid TPS response characteristics for application to flight. For both material types in the range of conditions appropriate to the shuttle application, the surface thermochemical response resulted in a small rate of change of mass and a negligible energy contribution. The thermal response in terms of surface temperature was controlled by the net heat flux to the surface; this net flux was influenced significantly by the surface catalycity and surface emissivity. The surface catalycity must be accounted for in defining simulation test conditions so that proper heat flux levels to, and therefore surface temperatures of, the test samples are achieved.

Schaefer, J. W.↗
NASA NTRS1974

Airborne infrared astronomy telescope

Description of a 91.5-cm (36-in.) airborne infrared telescope installed in a C141A StarLifter as a national IR observatory. The telescope system is mounted in a specially constructed cavity located just ahead of the leading edge of the wing. All controls and ancillary systems are located in consoles and racks mounted aft of the telescope. The telescope is a conventional Cassegrain design which can be used either directly with the focal point behind the primary mirror or in a folded configuration by inserting a tertiary mirror following the secondary which folds the optical path through the support bearing into the aircraft cabin area. The telescope system is designed to operate at all ambient conditions from sea level to 15,200 m. The system is optimized for operation at ambient temperatures experienced at 13,000 to 15,000 m (220 K). The entire telescope assembly with the exception of noncritical covers and brackets is constructed of Invar-type material to minimize the effects of thermal distortions. Pointing accuracy and stability of the telescope with respect to the target are achieved through multiple stages of stabilization and vibration isolation equipment.

Cameron, R. M.↗
NASA NTRS1975

Asteroids - Infrared photometry at 1.25, 1.65, and 2.2 microns

We report the first results of a new program of asteroid photometry at wavelengths of 1.25, 1.65, and 2.2 mu. In this paper the observations of three asteroids are reduced to spectral reflectance. Ceres and Pallas have surfaces which are probably composed of carbonaceous chondritic-type material. A basaltic achondritic composition remains a good candidate for Vesta.

Johnson, T. V.↗
NASA NTRS1976

Prediction of the acoustic impedance of duct liners

Recent research which contributes to the prediction of the acoustic impedance of duct liners is reviewed. This review includes the linear and nonlinear properties of sheet and bulk type materials and methods for the measurement of these properties. It also includes the effect of grazing flow on the acoustic properties of materials. Methods for predicting the properties of single or multilayered, point reacting or extended reaction, and flat or curved liners are discussed. Based on this review, methods for predicting the properties of the duct liners which are typically used in aircraft engines are recommended. Some areas of needed research are discussed briefly.

Zorumski, W. E.↗
NASA NTRS1978

Automated predesign of aircraft

Program uses multistation structural-synthesis to size and design box-beam structures for transport aircraft. Program optimizes static strength and scales up to satisfy fatigue and fracture criteria. It has multimaterial capability and library of materials properties, including advanced composites. Program can be used to evaluate impact on weight of variables such as materials, types of construction, structural configurations, minimum gage limits, applied loads, fatigue lives, crack-growth lives, initial crack sizes, and residual strengths.

Poe, C. C., Jr.↗
NASA NTRS1976

The problem of internal and edge cracks in an orthotropic strip

The plane elastostatic problem of internal and edge cracks in an infinite orthotropic strip is considered. The problems for the material types 1 and 2 are formulated in terms of singular integral equations. For the symmetric case the stress intensity factors are calculated and are compared with the isotropic results. The results show that because of the dependence of the Fredholm kernels on the elastic constants, unlike the crack problem for an infinite plane, in the strip the stress intensity factors are dependent on the elastic constants and are generally different than the corresponding isotropic results.

Delale, F.↗
NASA NTRS1977

The problem of internal and edge cracks in an orthotropic strip

The plane elastostatic problem of internal and edge cracks in an infinite orthotropic strip is considered. The problems for the material types I and II are formulated in terms of singular integral equations. For the symmetric case the stress intensity factors are calculated and are compared with the isotropic results. The results show that because of the dependence of the Fredholm kernels on the elastic constants, unlike the crack problem for an infinite plane, in the strip the stress intensity factors are dependent on the elastic constants and are generally different from the corresponding isotropic results.

Delale, F.↗
NASA NTRS1977

The problem of internal and edge cracks in an orthotropic strip

The plane elastostatic problem of internal and edge cracks in an infinite orthotropic strip is considered. The problems for the material types I and II are formulated in terms of singular integral equations. For the symmetric case the stress-intensity factors are calculated and are compared with the isotropic results. The results show that because of the dependence of the Fredholm kernels on the elastic constants in the strip (unlike the crack problem for an infinite plane) the stress-intensity factors are dependent on the elastic constants and are generally different from the corresponding isotropic results

Delale, F.↗
NASA NTRS1977

Elasto-plastic flow in cracked bodies using a new finite element model

Cracked geometries were studied by finite element techniques with the aid of a new special element embedded at the crack tip. This model seeked to accurately represent the singular stresses and strains associated with the elasto-plastic flow process. The present model was not restricted to a material type and did not predetermine a singularity. Rather the singularity was treated as an unknown. For each step of the incremental process the nodal degrees of freedom and the unknown singularity were found through minimization of an energy-like functional. The singularity and nodal degrees of freedom were determined by means of an iterative process.

Karabin, M. E., Jr.↗
NASA NTRS1977

An experimental investigation on the tensile moduli and strengths of graphite/epoxy laminates

The results of a series of tensile tests on some graphite/epoxy laminates, at rates varying from 0.002 to 2 in./min are examined. The loads were applied at various angles to the fiber directions in each case. The rate-dependent behavior of the stress-strain response is assessed. Evidence is presented to indicate that failure first occurs on inner plies, and that, in some cases, moduli increase with increasing stress (or strain) level. Lamination theory is used to predict the moduli, and comparisons with experiment are given. This theory is also used in conjunction with three failure theories to predict ultimate strengths (with varying degrees of success). Further, two approaches to ply unloading after first-ply failure are used and discussed. One is a standard method found in the literature while the other is a proposed 'strength-of-materials' type of technique which is computationally much simpler.

Yeow, Y. T.↗
NASA NTRS1975

Correlation of Al/Si X-ray fluorescence data with other remote sensing data from the Taurus-Littrow area

Al/Si intensity ratios from the Apollo 15 X-ray fluorescence experiment have been analyzed in conjunction with such other remote-sensing data as visible albedo measurements, color-difference photographs, and relative spectral reflectivity curves for the purpose of defining geochemical units in the Taurus-Littrow area. A geochemical boundary between the dark-mantle unit and the western edge of the Taurus Mountains is indicated by all the remote-sensing techniques considered. The major component of the ejecta from Catena Littrow, located within the dark-mantle unit, is highland-type material. The areal extent of the ejecta determined from the Al/Si data is at least 30 km along the Apollo 15 ground track. The constraint imposed upon depth to high-alumina material at Catena Littrow is 520 m. If the high-alumina material excavated at Catena Littrow is an extension of the Taurus Mountain 'roots', then the maximum slope of the buried highland surface from Catena Littrow to the Taurus Mountains border is less than 2.0 deg

Andre, C. G.↗
NASA NTRS1979

Reflectance spectra for 277 asteroids

Visible and near-infrared reflectance spectra are presented for 277 asteroids. These represent the results of an 8-yr program and constitute all spectra available in 1979. There are approximately 80 recognizably different spectral types among the asteroids surveyed. Relatively few of these can be explained as mixtures of C- and S-type materials on individual asteroids, although Eos family members may be an exception.

Chapman, C. R.↗
NASA NTRS1981

Surface temperatures and glassy state investigations in tribology, part 4

Measurements were made of the limiting shear stress for two naphthenic oils of differing molecular weight and three blends of the lower molecular weight oil and polyalkylmethacrylate polymers of differing molecular weight. The two base oils reached the same limiting shear stress for the same temperature and pressure. This was also true for all the polymer solutions although the polymer reduced the limiting shear stress by about 15 percent. It is shown that limiting stress is more a function of material type than viscosity or molecular weight. A new falling body viscometer was constructed to operate to 230 C and 0.6 GPa. Another viscometer was constructed to extend the pressure range to 1.1 GPa. A concentrated contact simulator was developed which allows recording of the traction force while the slide-roll ratio is continuously varied and the rolling speed is maintained essentially constant by a single drive motor. The configuration is that of a crowned roller against a disk. Measurement of lubricant minimum film thickness of elliptical EHD contacts of various aspect ratios were made by optical interferometry. The data collected were used to evaluate the Hamrock and Dowson minimum film thickness model over a range of contract ellipticity ratio where the major axis of the contact ellipse was aligned both parallel and perpendicular to the direction of motion. A statistical analysis of the measured film thickness data showed that on the average the experimental data were 30 percent greater than the film thickness predicted by the model. Preliminary development of the application of a scanning infrared radiation system to a tribo-system was completed.

Bair, S. S.↗
NASA NTRS1981

The E3 combustors: Status and challenges

The design, fabrication, and initial testing of energy efficient engine combustors, developed for the next generation of turbofan engines for commercial aircraft, are described. The combustor designs utilize an annular configuration with two zone combustion for low emissions, advanced liners for improved durability, and short, curved-wall, dump prediffusers for compactness. Advanced cooling techniques and segmented construction characterize the advanced liners. Linear segments are made from castable, turbine-type materials.

Sokolowski, D. E.↗
NASA NTRS1981

The E3 combustors - Status and challenges

The technology programs for the Energy Efficient Engine (E3) combustors are outlined, status and test results to date are summarized, and present and future challenges indicated. The NASA-sponsored programs, which are being conducted at the General Electric Company and Pratt & Whitney Aircraft, are making important technology advances. Both combustor designs utilize an annular configuration with two-zone combustion for low emissions, advanced liners for improved durability, and short, curved-wall, dump prediffusers for compactness. Advanced cooling techniques and segmented construction characterize the advanced liners in both programs. Liner segments are made from castable, turbine-type materials. At this time, analysis and design activities have been completed; experimental evaluations are progressing. Test results are verifying both design concepts for combustion, cooling, and mechanical integrity. All goals appear capable of being met, with the exception of NO(x).

Sokolowski, D. E.↗
NASA NTRS1984

Low-Noise Submillimeter-Wave Diode

Low noise achieved without usual high resistance. Barrier of p-type material placed between metal anode and heavily-doped gallium arsenide. Ntype epitaxial layer eliminated. Barrier prevents quantum tunneling of electrons between semiconductor and metal. Higher breakdown structure provided.

Mattauch, R. J.↗
NASA NTRS1983

Small gas turbine combustor study - Combustor liner evaluation

A reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) is compared both analytically and experimentally with a conventional splash film-cooled design with the same combustor configuration. Comparison of selected critical combustor panels indicated that it was possible to maintain the liner temperature similar between the two configurations using 50 percent less coolant for the Lamilloy as compared with the reference film-cooled combustor. Additional benefits indicated improvement in outlet temperature distribution and NOx emission level.

Norgren, C. T.↗