Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

X-ray measurements of stresses and defects in EFG and large grained polycrystalline silicon ribbons

The Bond method was employed to measure the lattice parameter in an area of 0.4 mm in diameter of EFG Si-ribbons to an accuracy of + or - 0.00008 A. A Bond goniometer was built which included a goniostat with a special specimen holder to mount ribbons 1 m in length and 75 mm in width which could be rotated about two orthogonal axes, and a Leitz microscope for precision alignment of a particular area into the center of the goniostat and the small primary X-ray beam. The (321) planes were found to be parallel to the surface of the ribbons with an angular spread of about 15 deg. The poles of the (111) planes clustered about an angle of 25 deg away from the surface normal, again with a spread of 10 deg. The lattice parameter of a small piece of ribbon material was found to be a sub o = 5.43075 A. A maximum stress of 115 MPa was observed in a fractured ribbon which corresponded to the fracture stress of single crystals of Si.

Wagner, C. N. J.↗
NASA NTRS1982

The Orthogonal In-Situ Machining of Single and Polycrystalline Aluminum and Copper, Volume 1

Metal cutting is a unique deformation process characterized by large strains, exceptionally high strain rates and few constraints to the deformation. These factors, along with the difficulty of directly measuring the shear angle, make chip formation difficult to model and understand. One technique for skirting the difficulty of post mortem chip measurement is to perform a cutting experiment dynamically in a scanning electron microscope. The performance of the in-situ experiment with full instrumentation allows for component force measurement, orientation measurement (on a round single crystal disk) and a timing device, all superimposed below the deformation on the TV monitor and recorded for future viewing. This allows the sher angle to be directly measured for the screen along with the other needed information.

Cohen, P. H.↗
NASA NTRS1982

An EBIC study of HEM polycrystalline silicon

Low-cost silicon for solar cells grown by the heat exchanger method (HEM) was studied in the electron beam induced current (EBIC) mode of a scanning electron microscope (SEM). Comparisons were made between the defects observed optically and the recombination centers visible in EBIC. Much of the HEM material was single crystalline, but structural defects were found from areas near the corners of the grown material. Most of these defects consisted of linear twin boundaries and grain boundaries. The electrical activity of these boundaries was dependent on symmetry of the boundaries. Symmetric twin boundaries did not exhibit recombination activity while unsymmetric twin boundaries were electrically active.

Koch, T.↗
NASA NTRS1983

Measuring Diffusion and Recombination in Polycrystalline Silicon

Light-beam-induced currents yield information about solar cell material. Apparatus measures short-circuit current generated when spot of concentrated light is scanned across grains and grain boundaries in material under test. Technique used to evaluate SOC samples for diffusion and recombination effects of cell processing and chemical and structural defects.

Zook, J. D.↗
NASA NTRS1982

The strength and ductility of polycrystalline NiAl in tension

Experiments at temperatures from 20 C to 400 C at two strain rates (.0001/s and .000005/s) establish that: (1) at room temperatures, binary and microalloyed ( 1000 ppm La, Y, Mo, Ti) NiAl shows negligible ductility, independent of grain size over the range 5 to 140 micrometers; (2) at 295 C the tensile elongation of binary 51 Ni/49 Al increases from 1% to about 5% upon decreasing the grain size to below approximately 10 micrometers; (3) similarly, at 400 C the ductility increases from about 2% to 15% upon decreasing the grain size to below 15 micrometers; (4) the ductility of fine grained (7 micrometer) binary aggregates deformed at 295 C increases from approximately 5% to 12% upon decreasing the strain rate from .0001/s to .000005/s; (5) partial recrystallization (10% to 20%) of warm extruded binary and microalloyed material imparts 1% to 2% ductility at room temperature where fully recrystallized material is brittle; (6) the yield strength obeys a Hall-Petch relationship; and (7) when ductility is not observed, fracture coincides with yielding. The mechanisms underlying the flow and fracture of NiAl are discussed in terms of the nucleation and growth of microcracks. The concept of a critical grain size is considered in the light of the results.

Schulson, E. M.↗
NASA NTRS1983

Micromechanically Based Constitutive Relations for Polycrystalline Solids

A basic method to estimate the overall mechanical response of solids which contain periodically distributed defects is presented. The method estimates the shape and growth pattern of voids periodically distributed over the grain boundaries in a viscous matrix. The relaxed moduli are obtained for a polycrytalline solid that undergoes relaxation by grain boundary sliding which accounts for the interaction effects. The overall inelastic nonlinear response at elevated temperatures in terms of a model which considers nonlinear power law creep within the grains, and linear viscous flow in the grain boundaries is discussed.

Nemat-Nasser, S.↗
NASA NTRS1985

The effect of tantalum on the structure/properties of two polycrystalline nickel-base superalloys: B-1900 + Hf MAR-M247

The microstructure, phase compositions, and phase fractions were studied in conventionally cast B-1900 + Hf and both conventionally cast and directionally solidified MAR-M247 as a function of tantalum concentration. The hot tensile and creep rupture properties of the solutionized and aged MAR-M247-type alloys were also determined as a function of tantalum level. The effects of tantalum on the microstructure and phase compositions of B-1900 + Hf and MAR-M247 (conventionally cast and directionally solidified) were found to be very similar. The addition of tantalum to the as cast and heat treated alloys was shown to cause the partial replacement of the Hf in the MC carbides by Ta, although the degree of replacement was decreased by the solutionizing and aging heat treatment. The gamma prime and minor phase fractions (primarily MC type carbides) both increased approximately linearly with tantalum concentration. The gamma prime phase compositions were relatively insensitive to tantalum variations with the exception of the tantalum and/or hafnium levels. Bulk tantalum additions increased the tantalum, chromium, and cobalt levels of the gamma phase in both alloy series. The increase in the concentrations of the latter two elements in the gamma phase was a result of the decrease in the gamma phase fraction with increasing bulk tantalum concentration and constant gamma/gamma prime partitioning ratio. Tantalum additions increased the yield stress and ultimate tensile strength of the directionally solidified MAR-M247 type alloys and had no significant effect on ductility.

Janowski, G. M.↗
NASA NTRS1984

Advances in large area polycrystalline solar cells

Polycrystaline silicon is presently routinely processed into low cost 10 cm by 10 cm solar cells. However assuming minimal handling difficulties, only minor equipment modifications and no increase in processing complexity, the fabrication of even larger geometries would be economically advantageous. This investigation addressed the feasibility of developing 10 cm by 15 cm solar cells from research through pilot line production stages. The major thrust was to minimize costing by using existing production equipment and proven techniques wherever possible. Accordingly methods were developed to section larger substrates from existing cast ingots, a simple solar cell was designed and low cost processes implemented. After numerous preliminary experiments, pilot line production of 1500 cells was completed. Of these approximately 62 percent exhibited efficiencies greater than 7.0 percent, 53 percent were greater than 8.0 percent and 15 percent were greater than 9.0 percent. Based on this study, the regular production of 10 cm by 15 cm solar cells was determined to be both feasible and cost effective using existing processing methods.

Vendura, G. J., Jr.↗
NASA NTRS1985

An inert marker study for palladium silicide formation - Si moves in polycrystalline Pd2Si

A novel use of Ti marker is introduced to investigate the moving species during Pd2Si formation on 111 and 100 line-type Si substrates. Silicide formed from amorphous Si is also studied using a W marker. Although these markers are observed to alter the silicide formation in the initial stage, the moving species can be identified once a normal growth rate is resumed. It is found that Si is the dominant moving species for all three types of Si crystallinity. However, Pd will participate in mass transport when Si motion becomes obstructed.

Ho, K. T.↗
NASA NTRS1986

The effects of tantalum on the microstructure of two polycrystalline nickel-base superalloys - B-1900 + Hf and MAR-M247

The effect of changing the content of Ta on the gamma/gamma-prime carbide microstructure was investigated in two crystalline nickel-base superalloys: conventionally cast B-1900 + Hf, and both conventionally cast and directionally solidified MAR-M247. The changes occurring in the microstructure effects were similar in both alloys. The gamma-prime and carbide volume fractions increased linearly with Ta additions, while the gamma-prime phase compositions did not change. Bulk Ta additions increased the levels of Cr and Co (in addition to that of Ta) of the gamma phase, a result of the approximately constant partitioning ratios for these two elements. The addition of Ta led to a partial replacement of Hf in the MC carbides. In addition, Cr-rich M(23)C(6) carbides formed as a result of MC carbide decomposition during heat treatment.

Heckel, R. W.↗
NASA NTRS1989

Auger electron intensity variations in oxygen-exposed large grain polycrystalline silver

Auger electron spectroscopic studies of the grains in oxygen-charged polycrystal-line silver show significant intensity variations as a function of crystallographic orientation. These intensity variations were observed by studies of the Auger images and line scans of the different grains (randomly selected) for each silver transition energy. The results can be attributed to the diffraction of the ejected Auger electrons and interpreted by corresponding changes in the electron mean-free path for inelastic scattering and by oxygen atom accumulation in the subsurface. The subsurface (second layer) octahedral sites increased in size because of surface relaxation and serve as a stable reservoir for the dissolved oxygen.

Lee, W. S.↗
NASA NTRS1989

Thermoelastic micromechanical stresses associated with a large alpha-silicon carbide grain in a polycrystalline beta-silicon carbide matrix

The thermoelastic micromechanical stresses associated with a single large hexagonal alpha-SiC grain within a fine-grain-size cubic (3C) beta-SiC matrix were calculated. The naturally occurring residual stresses which are created during cooling from the processing temperatures and the effects of superimposed applied external stresses are both considered. A significant effect of the shape or geometry of the alpha-SiC grain is revealed, with the largest residual stresses associated with the naturally occurring tabular or platelet structure. The stresses are compared with the published strength results for these materials, which suggests that the residual stresses assume a significant role in the strength reduction that is observed.

Li, Zhuang↗
NASA NTRS1990

Elliptical flux vortices in polycrystalline YBa2Cu3O7

The formation of an Abrikosov flux vortex with its core axis perpendicular to an anisotropic (a-c or b-c) plane in YBa2Cu3O7 requires only 1/10 of the energy required by the formation of a vortex with its core axis perpendicular to an isotropic (a-b) plane. It is not unusual for 18 to 35 percent of shake and bake bulk YBa2Cu3O7 to consist of empty pockets or voids inside the material. Studies estimate that 75 percent of the internal grain boundaries contain a-b planes. If many of the a-b planes are incident upon other grains, then many of the a-c and/or b-c planes must be incident on the voids. Evidently there are a large number of exposed anisotropic planes inside the bulk material. This condition is conducive to the formation of vortices that are perpendicular to the anisotropic planes. The magnetic flux density around such a vortex is constant along contour lines that are elliptical in shape, while the circulating supercurrent density must vary in magnitude along the same contour lines. The impact of this elliptical structure on the possibility of a Kosterlitz-Thouless type phase transition as the bulk material goes from superconducting to normal conducting is discussed. Implications with regard to the excess low frequency electrical noise that occurs at the temperature induced transition are also examined.

Hickman, H.↗