Engineering topics

Wightman, J. P.

Publications and source records attributed to Wightman, J. P..

At least 37 records · Page 2

NASA NTRS1985

Characterization of carbon fibers and fiber-matrix adhesion in composites

The effect of fiber/matrix interactions on the mechanical properties of thermoplastic carbon fiber composites was determined. The experimental approach was a multi-faceted one involving the following areas: characterization of the surface of carbon fibers using X-ray photoelectron spectroscopy (XPS), secondary ion mass spectroscopy (SIMS) and scanning transmission electron microcopy (STEM); determination of the functional groups on carbon fiber surfaces using an elemental tagging scheme - derivatization; determination of the polar and dispersion contribution to the surface energy of carbon fibers by measuring wetting forces in a series of liquids having known polar and dispersion components; and study of the interaction of thermoplastic polymers with carbon surfaces by solution adsorption, STEM and fiber critical length.

Wightman, J. P.↗

NASA NTRS1984

A fundamental approach to the sticking of insect residues to aircraft wings

A proposed testing scheme is described for obtaining data on the effects of surface roughness and surface energy on insect adhesion. The road test apparatus is discussed as well as surface preparation techniques. Uncoated and polymer coated metal substrates were analyzed by SEM/ESCA/IRS before and following collision with insects. Critical surface tensions of unexposed Nyebar and poly sulfone coatings were 10 and 33 dynes/cm, respectively, as determined from contact angles. A total of 95% of insect residues collected belong to order Diptera. Significantly less insect debris was detected on the coated plates as compared to the uncoated plates. Minimal contamination at the 5 nm level of both coated and uncoated plates occurs even after hours of exposure to road conditions as determined by ESCA analysis. The presence of nitrogen detected by ESCA on exposed plates is unequivocal evidence for insect residues left on plates.

Eiss, N. S., Jr.↗

NASA NTRS1984

The application of thermodynamic and spectroscopic techniques to adhesion in the polyimide/Ti 6-4 and polyphenylquinoxaline/Ti 6-4 systems

The results of calorimetric measurements of Ti adherend surfaces are presented. The measurements were carried out after several chemical pretreatments and after fracture of several lap shear samples aged at high temperature. The exact composition of the Ti samples was Ti(6 percent Al-4 percent V). The adhesives used were polyimides and polyphenylquinoxalines (PPQ). Each chemical pretreatment was accompanied by a unique spectroscopic feature which was characterized by XPS, SEM, and specular reflectance infrared spectroscopy. The energetics of the interaction between primer solutions and the Ti adherend were evaluated by microcalorimetry. Changes in the structure of the surface oxide layer upon heating of the adherend were deduced from immersion temperatures of the PI and PPQ solutions. The XPS and SEM data are given is a table.

Dias, S.↗

NASA NTRS1983

Surface analysis in composite bonding

Surface analysis results for graphite fibers and for graphite reinforced composites prior to adhesive bonding and following fracture of lap shear samples are discussed.

Messick, D. L.↗

NASA NTRS1983

Surface analysis of graphite fiber reinforced polyimide composites

Several techniques have been used to establish the effect of different surface pretreatments on graphite-polyimide composites. Composites were prepared from Celion 6000 graphite fibers and the polyimide LARC-160. Pretreatments included mechanical abrasion, chemical etching and light irradiation. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were used in the analysis. Contact angle of five different liquids of varying surface tensions were measured on the composites. SEM results showed polymer-rich peaks and polymer-poor valleys conforming to the pattern of the release cloth used durng fabrication. Mechanically treated and light irradiated samples showed varying degrees of polymer peak removal, with some degradation down to the graphite fibers. Minimal changes in surface topography were observed on concentrations of surface fluorine even after pretreatment. The light irradiation pretreatment was most effective at reducing surface fluorine concentrations whereas chemical pretreatment was the least effective. Critical surface tensions correlated directly with the surface fluorine to carbon ratios as calculated from XPS.

Messick, D. L.↗

NASA NTRS1983

Interaction of hydrogen chloride and water with oxide surfaces. III - Titanium dioxide

The adsorption of hydrogen chloride and water vapors on five TiO2 powders in both the anatase and rutile crystalline forms was studied as a function of temperature, pressure, and outgas conditions. The adsorbents were characterized utilizing X-ray powder diffraction, scanning electron microscopy, surface area analysis, indicator method, microelectrophoresis, XPS, and infrared spectroscopy. It was found that both outgas temperature and adsorption temperature influenced the adsorption of water vapor on TiO2, while water vapor adsorption on TiO2 was completely reversible. It is argued that the number of hydroxyl groups present on the surface determines the adsorption capacity of water on the different titanium dioxides. It was found that heats of immersion in water were affected significantly by outgas temperature. Hydrogen chloride adsorption isotherms at 30 C measured on TiO2 after outgassing at 100-400 C showed that a part of the total HCl adsorbed was irreversibly adsorbed. The highest HCl adsorption capacity per unit area was exhibited by anatase, while pure rutile exhibited the lowest adsorption capacity.

Siriwardane, R. V.↗

NASA NTRS1983

A critical study of the role of the surface oxide layer in titanium bonding

Scanning electron microscope/X-ray photoelectron spectroscopy (SEM/XPS) analysis of fractured adhesively bonded Ti 6-4 samples is discussed. The text adhesives incuded NR 056X polyimide, polypheylquinoxaline (PPQ), and LARC-13 polyimide. Differentiation between cohesive and interfacial failure was based on the absence of presence of a Ti 2p XPS photopeak. In addition, the surface oxide layer on Ti-(6A1-4V) adherends is characterized and bond strength and durability are addressed. Bond durability in various environmental conditions is discussed.

Dias, S.↗

NASA NTRS1983

A fundamental approach to the sticking of insect residues to aircraft wings

The sticking of insect residues to aircraft wings is investigated. The major topics of this review are: Experimentally tested methods, testing techniques, the effect of surface roughness height on aerodynamic drag, materials tested and, the adhesive properties of insect body fluids are reviewed.

Eiss, N. S., Jr.↗

NASA NTRS1983

Surface analysis in composite bonding

X ray photoelectron spectroscopy and contact angle measurements on graphite fiber composites pretreated in a number of different ways including mechanical, chemical, and light irradiation were analyzed. Data acquired on surface contamination as a result of fabrication techniques provides answers to the strength and durability of adhesively bonded composites. These techniques were shown to provide valuable information on surface analysis of pretreated composites prior to adhesive bonding and following lap shear fracture.

Messick, D. L.↗

NASA NTRS1983

Heats of immersion of titania powders in primer solutions

The oxide layer present on titanium alloys can play an important role in determining the strength and durability of adhesive bonds. Here, three titania powders in different crystalline phases, rutile-R1, anatase-A1, and anatase-A2, are characterized by several techniques. These include microelectrophoresis, X-ray diffractometry, surface area pore volume analysis, X-ray photoelectron spectroscopy, and measurements of the heats of immersion. Of the three powders, R1 has the highest heat of immersion in water, while the interaction between water and A1 powder is low. Experimental data also suggest a specific preferential interaction of polyphenylquinoxaline with anatase.

Siriwardane, R.↗

NASA NTRS1983

An investigation of adhesive/adherend and fiber/matrix interactions. Part B: SEM/ESCA analysis of fracture surfaces

Adhesion was studied with emphasis on the characterization of surface oxide layers, the analysis of fracture surfaces, and the interaction of matrices and fibers. A number of surface features of the fractured lap shear samples were noted in the SEM photomicrographs including the beta phase alloy of the Ti 6-4 adherend, the imprint of the adherend on the adhesive failure surface, increased void density for high temperature samples, and the alumina filler particles. Interfacial failure of some of the fractured lap shear samples is invariably characterized by the appearance of an ESCA oxygen photopeak at 530.3 eV assigned to the surface oxide layer of Ti 6-4 adherend. The effect of grit blasting on carbon fiber composites is evident in the SEM analysis. A high surface fluorine concentration on the composite surface is reduced some ten fold by grit blasting.

Beck, B.↗

NASA NTRS1983

Surface characterization of Ti and Ti (6 percent, Al-4 percent, V) metal powders and interaction with primer solutions

The interaction of Ti and Ti 6-4 powders with water and primer solutions was investigated experimentally by measuring the heats of immersion. Similar comparative studies were made on anatase and rutile TiO2 powders. The surface oxide layers of Ti and Ti 6-4 cracked on heating in vacuum between 300 and 400 C as evidenced by high heats of immersion in both water and primer solutions. Polyimide and polyphenylquinoxaline interacted preferentially, compared with the solvents with both metal powders after outgassing at room temperature. The heats of immersion of Ti 6-4 in water, solvents, and primer solutions increased significantly after pretreatment of the powder by an alkaline etch and a phosphate-fluoride process. The TiO2 powders were not satisfactory models for the surface oxide layer on either Ti or Ti 6-4 powder.

Siriwardane, R. V.↗

NASA NTRS1983

Surface analysis of grapite fiber reinforced polyimide composites. I

The results of experimental analyses of the effects of pretreatment on bonding between composite materials are reported. The materials comprised graphite fibers in a polyimide matrix. The surfaces were bonded as-received or subjected to grit blasting, bead blasting, hand sanding, washes with ethanolic KOH, NH2NH2-H2O or H2SO4 + 0.30 H2O2 or flashblasting. SEM and X-ray photoelectron spectroscopy revealed fluorine contents in the as-received samples. Contact angles were determined by means of five different liquids with various surface tensions. The flashblast technique removed all fluorine from the samples. Low critical surface tensions were found in the composite surfaces with high fluorine concentrations. The surface scanning techniques are concluded to be useful for studying factors influencing the strength and durability of adhesively bonded composites.

Messick, D. L.↗

NASA NTRS1982

A critical study of the role of the surface oxide layer in titanium bonding

The molecular understanding of the role which the surface oxide layer of the adherend plays in titanium bonding is studied. The effects of Ti6-4 adherends pretreatment, bonding conditions, and thermal aging of the lap shear specimens were studied. The use of the SEM/EDAX and ESCA techniques to study surface morphology and surface composition was emphasized. In addition, contact angles and both infrared and visible reflection spectroscopy were used in ancillary studies.

Dias, S.↗

NASA NTRS1982

Surface analysis in composite bonding

The role of the interfacial region in determining the bond strength and durability of composite bonds is discussed. The characterization of a variety of carbon fibers including Celion 6000 using both scanning electron microscopy and X-ray photoelectron spectroscopy is discussed. The emphasis is on composite bonding, that is, the adhesive bonding between composites in contrast to fiber-matrix interaction. The primary objective of the research is the characterization of composite surfaces before adhesive bonding and after fracture of bonded specimens. Work done on the analysis of composite samples pretreated in a number of ways prior to bonding is detailed.

Messick, D. L.↗

NASA NTRS1982

An investigation of adhesive/adherend and fiber/matrix interactions. Part A: Surface characterization of titanium dioxide, titantium and titanium 6% Al to 4% V powders: Interaction with water, hydrogen chloride and polymers

The titanium dioxide surface is discussed. Polymer adhesive are also discussed. Titanium powders are considered. Characterization techniques are also considered. Interactions with polymers, water vapor, and HCl are reported. Adsorbents are characterized.

Siriwardane, R. V.↗

NASA NTRS1981

The application of surface analysis to polymer/metal adhesion

The use of scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) in the analysis of Ti 6-4 adherend surfaces is described. Differences in Ti 6-4 surface composition as determined by XPS after different chemical pretreatments are detailed. Analysis of fractured surfaces by SEM/XPS is used to establish the failure mode. The surface acidity of Ti 6-4 coupons can be established by reflectance visible spectroscopy using indicator dyes.

Wightman, J. P.↗

NASA NTRS1981

An investigation of adhesive/adherend and fiber matrix interactions

Research during the report period focused on continued scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) of lap shear samples and flatwise tensile specimens and on the surface characterization of TiO2, Ti 6-4, and Ti powders with particular emphasis on their interaction with primer solutions of both polyphenylquinoxaline and LaRC-13 polyimide. The use of SEM and XPS in the analysis of Ti 6-4 adherend surfaces is described as well as differences in Ti 6-4 surface composition after different chemical pretreatments. Analysis of fractured surfaces is used to established the failure mode. The surface acidity of Ti 6-4 coupons can be established by reflectance visible spectroscopy using indicator dyes.

Beck, B.↗