Engineering Papers⌕ Search

Engineering topics

Wang, Y

Publications and source records attributed to Wang, Y.

At least 181 records · Page 10

Critical Material and Process Issues for CO2 Separation from Coal-Powered Plants

Concentrating CO2 from the dilute coal combustion or gasification gas stream to a level suitable for sequestration purposes represents a major cost factor to curtail CO2 emissions by capture and sequestration schemes. This paper provides a short review of CO2 capture incentives, current separation processes, and research progress of various new technologies. Technically, CO2 can be separated out of a gas mixture by all the methods discussed in this work, such as distillation, absorption, adsorption, gas/solid reaction, membrane, electrochemical pump, hydrate formation, etc. The challenge lies in determining which approach is the most practical or feasible, and ultimately the most cost-efficient. Important material issues and their impacts on the process viability will be discussed.

01 COAL, LIGNITE, AND PEAT↗

Controlling Atomic Layer Deposition of TiO2 in Aerogels through Surface Functionalization

This report demonstrates a chemical functionalization method for controlling atomic layer deposition (ALD) of TiO{sub 2} in low-density nanoporous materials. Functionalization of silica aerogel with trimethylsilane is shown to strongly suppress TiO{sub 2} growth via ALD. Subsequent modification of the functionalization through selective removal of the hydrocarbon groups reactivates the aerogel towards TiO{sub 2} deposition. These results demonstrate the potential use of ALD as a selective tool for creating novel nanoporous materials. Nanoporous materials present significant technological advantage for a wide range of applications, including catalysis, energy storage and conversion, nanoelectronics to name just a few (1-4). Hence, there is considerable interest in developing synthetic pathways for the fabrication of nanoporous materials with tailored properties. Aerogels (AGs) are unique low-density, open-cell porous materials consisting of submicrometer pores and ligaments that can be used as a robust material platform for designing novel nanoporous materials. In recent years, a synthetic approach based on ALD on AG templates has emerged as a promising method for the directed growth of nanoporous materials (5-11, 18). This approach has been used successfully to prepare millimeter-sized high aspect ratio aerogels coated uniformly with zinc oxide (ZnO), tungsten (W) and alumina (Al{sub 2}O{sub 3}) (10, 11). The ALD process utilizes two sequential, self-limiting surface reactions resulting in a layer-by-layer growth mode. The self limiting nature of the surface reactions makes ALD a particularly suitable technique for uniform deposition onto high aspect ratio porous substrates. Additionally, chemical specificity of the surface reactions in ALD enables one to control the deposition process through selective functionalization of the substrate surface. In fact the functionalization of planar substrates such as silicon wafers with organosilane groups (R{sub n}SiX{sub 4-n} (n = 1-3)) has been shown to deactivate the substrate towards ZrO{sub 2}, HfO{sub 2}, ZnO, and TiO{sub 2} ALD processes (12-16). A possible mechanism for the deactivation effect is the blocking of surface functional groups, such as hydroxyl (OH) moieties, which serve as chemisorption sites for the ALD precursors and hence are essential for nucleating the deposition process. Henceforth, we shall refer to these surface functional groups as nucleation sites for the ALD process.

36 MATERIALS SCIENCE↗

Inspection 13.2 nm table-top full-field microscope

We present results on a table-top microscope that uses an EUV stepper geometry to capture full-field images with a halfpitch spatial resolution of 55 nm. This microscope uses a 13.2 nm wavelength table-top laser for illumination and acquires images of reflective masks with exposures of 20 seconds. These experiments open the path to the realization of high resolution table-top imaging systems for actinic defect characterization.

36 MATERIALS SCIENCE↗

Non-cubic crystal symmetry of CaSiO{sub 3} perovskite up to 18 GPa and 1600K.

In situ synchrotron X-ray diffraction experiments have been conducted on CaSiO{sub 3} perovskite (CaPv) in a double-stage multianvil apparatus up to 18 GPa and 1600 K using a newly developed step-scan diffraction technique, which utilizes an energy-dispersive setup with a solid-state detector and collimator assemblies to collect angle-dispersive diffraction data over a wide range of photon energies. Superlattice reflections were resolved throughout the pressure (P) and temperature (T) range of the experiments, confirming that the crystal symmetry of CaPv is neither cubic nor tetragonal. A combination of analyses of the complete two-dimensional intensity datasets (photon energy from 20 to 160 keV and 2{theta} angle from 3.0{sup o} to 9.0{sup o}) and Rietveld refinements at selected wavelengths revealed that the most likely space group of CaPv in the experimental P-T range, and therefore in the Earth's transition zone, is either Pbnm or Cmcm. The difference between these two space groups was too small to resolve with our technique.

43 PARTICLE ACCELERATORS↗

Thermal Equation of State of Copper Studied by High P-T Synchrotron X-ray Diffraction

The unit-cell volume of copper (Cu) has been measured by synchrotron x-ray at pressures and temperatures of up to 8.1 GPa and 1100 K. From pressure-volume-temperature (P-V-T) measurements, thermoelastic parameters of Cu were derived based on a modified high-T Birch-Murnaghan equation of state and a thermal pressure approach. The ambient bulk modulus derived from this work is comparable to previously reported value, whereas all other thermoelastic parameters of Cu have never been determined before. These results extend our knowledge of the fundamental thermophysical properties on Cu.

36 MATERIALS SCIENCE↗

Coexistence of weak ferromagnetism and ferroelectricity in the high pressure LiNbO{sub 3}-type phase of FeTiO{sub 3}.

We report the magnetic and electrical characteristics of polycrystalline FeTiO{sub 3} synthesized at high pressure that is isostructural with acentric LiNbO{sub 3} (LBO). Piezoresponse force microscopy, optical second harmonic generation, and magnetometry demonstrate ferroelectricity at and below room temperature and weak ferromagnetism below {approx} 120 K. These results validate symmetry-based criteria and first-principles calculations of the coexistence of ferroelectricity and weak ferromagnetism in a series of transition metal titanates crystallizing in the LBO structure.

36 MATERIALS SCIENCE↗

Underground Prototype Water Cherenkov Muon Detector with the Tibet Air Shower Array

We are planning to build a 10,000 m{sup 2} water-Cherenkov-type muon detector (MD) array under the Tibet air shower (AS) array. The Tibet AS+MD array will have the sensitivity to detect gamma rays in the 100 TeV region by an order of the magnitude better than any other previous existing detectors in the world. In the late fall of 2007, a prototype water Cherenkov muon detector of approximately 100 m{sup 2} was constructed under the existing Tibet AS array. The preliminary data analysis is in good agreement with our MC simulation. We are now ready for further expanding the underground water Cherenkov muon detector.

79 ASTRONOMY AND ASTROPHYSICS↗

Interfacial tension measurement of Ni-S liquid using high-pressure X-ray micro-tomography

High-pressure, high-temperature X-ray tomography experiments have been carried out using a large volume toroidal cell, which is optimized for interfacial tension measurements. A wide anvil gap, which corresponds to a field of view in the radiography imaging, was successively maintained to high pressures and temperatures using a composite plastic gasket. Obtained interfacial tensions of Ni-S liquid against Na, K-disilicate melt, were 414 and 336 mN/m at 1253 and 1293 K, respectively. Three-dimensional tomography images revealed that the sample had an irregular shape at the early stage of melting, suggesting either non-equilibrium in sample texture and force balance or partial melting of surrounding silicate. This information cannot always be obtained from two-dimensional radiographic imaging techniques. Therefore, a three-dimensional tomography measurement is appropriate for the precise interfacial measurements.

36 MATERIALS SCIENCE↗

Development of the multi-anvil assembly 6-6 for DIA and D-DIA type high-pressure apparatuses

A newly designed anvil assembly, Multi-anvil Assembly 6-6 (MA6-6), was developed. This assembly consists of six small anvils with an anvil guide, and can be compressed by DIA-type and deformation-DIA (D-DIA) apparatuses. The use of this anvil assembly simplifies the process of replacing anvils with those having different truncated edge length and/or hardness. As a consequence, the time needed for anvil replacement is significantly shortened. This is a benefit to experiments at synchrotron facilities because anvil replacement has to be carried out within the limited beamtime. Using a combination of an MA6-6 and DIA-type apparatus, pressure above 12 GPa was generated. A deformation experiment of polycrystalline MgO was performed using an MA6-6 with D-DIA at 4 GPa and room temperature. Two-dimensional X-ray diffraction patterns and X-ray radiographic images were collected from the deforming sample using monochromatic X-rays. Quantitative deformation experiments can be carried out using this experimental setup.

43 PARTICLE ACCELERATORS↗

In situ investigation of high-pressure melting behavior in the Fe-S system using synchrotron X-ray radiography

We studied the high-pressure melting behavior of Fe-S mixtures containing 9 wt% sulfur using the synchrotron X-ray radiographic method in a large volume press. By opening two graphite windows along the X-ray path and using boron nitride capsules, we were able to observe segregation of sulfur-rich liquid and iron-rich solid upon initial melting and determine the eutectic temperature of the Fe-S system at pressures between 13 and 16 GPa. Our results are in excellent agreement with the existing data from quench experiments, and are further supported by in situ X-ray diffraction measurements. The liquidus temperatures of this composition, determined on the basis of the disappearance of the solid phase on the radiographs, are also consistent with literature values. By observing radiographic changes with time, we monitored the approach to equilibrium and obtained preliminary data on the kinetics of the melting process.

43 PARTICLE ACCELERATORS↗

High-pressure cells for in situ multi-anvil experiments

A new series of high-pressure cells for in situ multi-anvil experiments is described. The cells are based on the conventional COMPRES cells, but modifications are made to improve the passage of X-rays. The modifications include cutting slits in parts of the assemblies that have very high X-ray absorption, such as lanthanum chromite and rhenium, the use of low-Z thermal insulation, such as forsterite, in place of zirconia, and the partial replacement of zirconia by MgO equatorial windows combined with a mullite octahedron. Details of the designs, thermal characterizations, and examples of the application of these cells are described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Melting curve of silicon to 15 GPa determined by two-dimensional angle-dispersive diffraction using a Kawai-type apparatus with X-ray transparent sintered diamond anvils

The melting curve of silicon has been determined up to 15 GPa using a miniaturized Kawai-type apparatus with second-stage cubic anvils made of X-ray transparent sintered diamond. Our results are in good agreement with the melting curve determined by electrical resistivity measurements [V.V. Brazhkin, A.G. Lyapin, S.V. Popova, R.N. Voloshin, Nonequilibrium phase transitions and amorphization in Si, Si/GaAs, Ge, and Ge/GaSb at the decompression of high-pressure phases, Phys. Rev. B 51 (1995) 7549] up to the phase I (diamond structure)-phase II ({beta}-tin structure)-liquid triple point. The triple point of phase XI (orthorhombic, Imma)-phase V (simple hexagonal)-liquid has been constrained to be at 14.4(4) GPa and 1010(5) K. These results demonstrate that the combination of X-ray transparent anvils and monochromatic diffraction with area detectors offers a reliable technique to detect melting at high pressures in the multianvil press.

36 MATERIALS SCIENCE↗

InSbN alloys prepared by two-step ion implantation for infrared photodetection

InSbN alloys are fabricated by two-step nitrogen ion implantation into InSb (111) wafers. X-ray photoelectron spectroscopy indicates that most of the implanted nitrogen ions substitute Sb to form In-N bonds. The percentage of the In-N bonds is found to decrease with the increase in the implanted nitrogen. Such alloys can effectively detect long wavelength infrared radiation and the absorption peak energies can be controlled by monitoring the implanted nitrogen dose. The measured peak wavelengths are consistent with the band gaps of the alloys calculated using a ten-band k{center_dot}p model.

36 MATERIALS SCIENCE↗

Crystallographically oriented Zn nanocrystals formed in ZnO by Mn{sup +}-implantation

The nanostructural characteristics of ZnO implanted with Mn{sup +} to doses ranging from 1x10{sup 15} to 1x10{sup 17} cm{sup -2} are systematically studied for both as-implanted and postannealed cases. The detailed structural characterizations confirmed that the Mn{sup +} implantation and postannealing result in (1) the formation of crystallographically orientated Zn nanocrystals in the ZnO matrix and (2) Mn atoms occupy the Zn sites in ZnO.

36 MATERIALS SCIENCE↗

Precise Branching Ratios to Unbound 12C States from 12N and 12B (beta)-Decays

Two complementary experimental techniques have been used to extract precise branching ratios to unbound states in {sup 12}C from {sup 12}N and {sup 12}B {beta}-decays. In the first the three {alpha}-particles emitted after {beta}-decay are measured in coincidence in separate detectors, while in the second method {sup 12}N and {sup 12}B are implanted in a detector and the summed energy of the three {alpha}-particles is measured directly. For the narrow states at 7.654 MeV (0{sup +}) and 12.71 MeV (1{sup +}) the resulting branching ratios are both smaller than previous measurements by a factor of {approx_equal} 2. The experimental results are compared to no-core shell model calculations with realistic interactions from chiral perturbation theory, and inclusion of three-nucleon forces is found to give improved agreement.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Determination of the proton separation energy of {sup 93}Rh from mass measurements

The proposed {nu}p process, which occurs in the early time proton-rich neutrino winds of core-collapse supernovae, has the potential to resolve the long-standing uncertainty in the production of the light p-nuclei {sup 92}Mo and {sup 94}Mo. A recent study incorporating this {nu}p process has indicated that the proton separation energy S{sub p} of {sup 93}Rh is especially important in determining the relative production of these two isotopes. To reproduce the observed solar {sup 92}Mo/{sup 94}Mo abundance ratio of 1.57 a S{sub p} value for {sup 93}Rh of 1.64{+-}0.1 MeV is required. The previously unknown masses of {sup 92}Ru and {sup 93}Rh have been measured with the Canadian Penning Trap mass spectrometer resulting in an experimental value for S{sub p}({sup 93}Rh) of 2.007{+-}0.009 MeV. This implies that with our current understanding of the conditions in core-collapse supernova explosions the {nu}p process is not solely responsible for the observed solar {sup 92}Mo/{sup 94}Mo abundance ratio.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗