Engineering Papers⌕ Search

Engineering topics

Ren, Yang

Publications and source records attributed to Ren, Yang.

At least 325 records · Page 18

In-situ synchrotron high energy X-ray diffraction study of phase transformation of intermetallic Ti 3 Sn

Ti 3 Sn has received increasing attention as high damping metallic material. However, information of solid state transformation and crystal structure of Ti 3 Sn were still incomplete. Here, in-situ synchrotron high energy XRD during heating/cooling and during uniaxial compressive loading were used to study the phase transformation of Ti 3 Sn. Thermal-induced reversible phase transformation of Ti 3 Sn was demonstrated, and it was found that such transformation could also be stress (strain) induced. Crystal structure, lattice parameters and atomic Wyckoff positions of new base-centered orthorhombic phase of Ti 3 Sn were suggested based on Rietveld refinement of XRD profiles. Lastly, the phase contents of Ti 3 Sn during heating/cooling processes were also discussed

36 MATERIALS SCIENCE↗

The Phase Diagram and Exotic Magnetostrictive Behaviors in Spinel Oxide Co(Fe1−xAlx)2O4 System

We report the magnetic and magnetostrictive behaviors of the pseudobinary ferrimagnetic spinel oxide system (1−x)CoFe2O4–xCoAl2O4 [Co(Fe1−xAlx)2O4], with one end-member being the ferrimagnetic CoFe2O4 and the other end-member being CoAl2O4 that is paramagnetic above 9.8 K. The temperature spectra of magnetization and magnetic susceptibility were employed to detect the magnetic transition temperatures and to determine the phase diagram of this system. Composition dependent and temperature dependent magnetostrictive behaviors reveal an exotic phase boundary that separates two ferrimagnetic states: At room temperature and under small magnetic fields (∼500 Oe), Fe-rich compositions exhibit negative magnetostriction while the Al-rich compositions exhibit positive magnetostriction though the values are small (<10 ppm). Moreover, the compositions around this phase boundary at room temperature (x = 0.35, 0.4, 0.45, 0.5) exhibit near-zero magnetostriction and enhanced magnetic susceptibility, which may be promising in the applications for magnetic cores, current sensors, or magnetic shielding materials.

36 MATERIALS SCIENCE↗

Building ultraconformal protective layers on both secondary and primary particles of layered lithium transition metal oxide cathodes

Despite their relatively high capacity, layered lithium transition metal oxides suffer from crystal and interfacial structural instability under aggressive electrochemical and thermal driving forces, leading to rapid performance degradation and severe safety concerns. In this paper, we report a transformative approach using an oxidative chemical vapour deposition technique to build a protective conductive polymer (poly(3,4-ethylenedioxythiophene)) skin on layered oxide cathode materials. The ultraconformal poly(3,4-ethylenedioxythiophene) skin facilitates the transport of lithium ions and electrons, significantly suppresses the undesired layered to spinel/rock-salt phase transformation and the associated oxygen loss, mitigates intergranular and intragranular mechanical cracking, and effectively stabilizes the cathode-electrolyte interface. This approach remarkably enhances the capacity and thermal stability under high-voltage operation. Building a protective skin at both secondary and primary particle levels of layered oxides offers a promising design strategy for Ni-rich cathodes towards high-energy, long-life and safe lithium-ion batteries.

25 ENERGY STORAGE↗

Experimental characterization of the effect of E×B shear on edge-harmonic oscillation mode structure

The Edge Harmonic Oscillation (EHO) mode is one of the characteristic modes that provides an edge transport channel during high-confinement ELM-free phase (the so-called Quiescent High confinement phase). Recent theoretical work and extensive experimental observations have suggested that the large rotational E×B shear is the key to destabilize an EHO. As the eigenmode grows to large amplitude, it will exert a drag on the rotation, resulting in EHO's saturation. However, detailed mechanisms concerning this process remain vague. We have performed here continuous tracking on how the E×B shear affects the EHO mode structure to search for a possible explanation of the saturation mechanism. Two edge density fluctuation diagnostics are employed to observe the eigenmode structure evolution of EHO in the pedestal region in the radial and poloidal directions, respectively. Our results show that the EHO mode's radial wavenumber is strongly correlated with the E×B shear rate, while the poloidal wavenumber is unaffected by the E×B shear rate. During the EHO existence, with the E×B shearing rate ramping down, the radial wavenumber is also observed to be decreasing.

42 ENGINEERING↗

Aqueous Li-ion battery enabled by halogen conversion–intercalation chemistry in graphite

The use of 'water-in-salt' electrolytes has considerably expanded the electrochemical window of aqueous lithium-ion batteries to 3 to 4 volts, making it possible to couple high-voltage cathodes with low-potential graphite anodes. However, the limited lithium intercalation capacities (less than 200 milliampere-hours per gram) of typical transition-metal-oxide cathodes preclude higher energy densities. Partial or exclusive anionic redox reactions may achieve higher capacity, but at the expense of reversibility. Here we report a halogen conversion-intercalation chemistry in graphite that produces composite electrodes with a capacity of 243 milliampere-hours per gram (for the total weight of the electrode) at an average potential of 4.2 volts versus Li/Li + . Experimental characterization and modelling attribute this high specific capacity to a densely packed stage-I graphite intercalation compound, C 3.5 [Br 0.5 Cl 0.5 ], which can form reversibly in water-in-bisalt electrolyte. By coupling this cathode with a passivated graphite anode, we create a 4-volt-class aqueous Li-ion full cell with an energy density of 460 watt-hours per kilogram of total composite electrode and about 100 per cent Coulombic efficiency. Here, this anion conversion-intercalation mechanism combines the high energy densities of the conversion reactions, the excellent reversibility of the intercalation mechanism and the improved safety of aqueous batteries.

25 ENERGY STORAGE↗

Long-Range Antiferromagnetic Order in a Rocksalt High Entropy Oxide

We report for the first time the magnetic structure of the high entropy oxide (Mg 0.2 Co 0.2 Ni 0.2 Cu 0.2 Zn 0.2 )O using neutron powder diffraction. This material exhibits a sluggish magnetic transition but possesses a long-range ordered antiferromagnetic ground state, as revealed by direct current and alternating current magnetic susceptibility, neutron diffraction, and spectroscopy. The magnetic propagation wavevector is k = (1/2, 1/2, 1/2) based on the cubic structure $Fm\bar{3m}$, and the magnetic structure consists of ferromagnetic sheets in the (111) planes with spins antiparallel between two neighboring planes. Neutron spectroscopy reveals strong magnetic excitations at 100 K that survive up to room temperature. Furthermore this work demonstrates that entropy-stabilized oxides represent a unique platform to study long-range magnetic order with an extreme chemical disorder.

36 MATERIALS SCIENCE↗

Identification of a Pt 3 Co Surface Intermetallic Alloy in Pt–Co Propane Dehydrogenation Catalysts

Bimetallic Pt-Co nanoparticles (NPs) were prepared and characterized by scanning transmission electron microscopy, in situ X-ray absorption spectroscopy, in situ synchrotron X-ray diffraction, and catalytic conversion for propane dehydrogenation with and without added H-2. In addition, the surface extended X-ray absorption fine structure (EXAFS) obtained by fitting the difference spectrum between the fully reduced and room-temperature-oxidized catalysts suggest that the surface structure remains Pt 3 Co, although the core changes from Pt to Pt 3 Co and to PtCo. At low Co loading, the bimetallic nanoparticles form a Pt3Co intermetallic surface alloy with Pt-rich core. With increasing Co loading, a full alloy forms where both the surface and NP compositions are Pt 3 Co. A further increase in Co loading leads to a Co-rich NP core, likely PtCo, with a surface of Pt 3 Co. Although Pt-Co intermetallic alloys form two different phases and several morphologies, the surface structures are similar in all catalysts. Although both monometallic Pt and Co are active for alkane dehydrogenation, all bimetallic Pt-Co catalysts are significantly more olefin selective than either single metal. The turnover rates of the bimetallic catalysts indicate that Pt is the active atom with little contribution from Co atoms. The high olefin selectivity is suggested to be due to Co acting as a less active structural promoter to break up large Pt ensembles in bimetallic NPs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Negative Thermal Expansion in (Hf,Ti)Fe 2 Induced by the Ferromagnetic and Antiferromagnetic Phase Coexistence

Negative thermal expansion (NTE) is an intriguing physical phenomenon that can be used in the applications of thermal expansion adjustment of materials. In this study, we report a NTE compound of (Hf,Ti)Fe 2 , while both end members of HfFe 2 and TiFe 2 show positive thermal expansion. The results reveal that phase coexistence is detected in the whole NTE zone, in which one phase is ferromagnetic (FM), while the other is antiferromagnetic (AFM). With increasing temperature, the FM phase is gradually transformed to the AFM one. The NTE phenomenon occurs in the present (Hf,Ti)Fe 2 because of the fact that the unit cell volume of the AFM phase is smaller than that of the FM phase, and the mass fraction of the AFM phase increases with increasing temperature. The construction of phase coexistence can be a method to achieve NTE materials in future studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design and thermomechanical properties of a γ' precipitate-strengthened Ni-based superalloy with high entropy γ matrix

A novel Ni-based superalloy was designed with γ' precipitate strengthening, controlled γ/γ' lattice misfit and high configurational entropy of the γ matrix for improved high temperature performance up to 800 degrees C. The alloy contains nano-sized γ' precipitates, MC and other grain boundary carbides. Three variants of the alloy were fabricated using vacuum induction melting, a computational-based homogenization cycle for reducing solidification segregation, and thermomechanical processing steps of forging followed by hot rolling to produce plates from which ASTM standard test specimens were extracted. Tensile testing at room temperature and elevated temperatures up to 800 degrees C revealed superior yield stress when compared to Nimonic 105 with good tensile strength values. Furthermore, the three alloys are machinable with maximum stresses comparable to standard practices as determined using deformation mechanisms maps obtained from Gleeble testing and EBSD analysis. Due to the composition of the experimental alloys falling outside the typical range used to populate thermodynamic databases, differences in phase predictions and related temperatures were observed between the experiment and Thermo-Calc predictions. Here, the γ' forming elements Ti and Nb had a similar effect on the γ' precipitates and indirectly contributed to changing the entropy of the γ matrix. Based on the results of this study, these alloys have the potential for use at 800 degrees C in energy structural applications. Definitions related to this novel class of alloys are discussed.

36 MATERIALS SCIENCE↗

Surface Modification for Suppressing Interfacial Parasitic Reactions of a Nickel-Rich Lithium-Ion Cathode

Ni-rich lithium nickel manganese cobalt oxides (Li-Ni x Mn y Co 1-x-y O 2 , x >= 0.5, NMCs) are high-capacity cathode materials for Li-ion batteries, but they exhibit limited cycling stability under high cutoff potentials. Various aspects, including transition metal dissolution, structural disordering, particle cracking, surface film thickening, etc., have already been investigated in terms of their performance degradation in the battery research community. Interestingly, these phenomena were primarily observed at the surface layer of the cathode material, implying that they may also be facilitated by some interfacial parasitic reactions between the delithiated NMC electrode and the non-aqueous electrolyte. Here in this study, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC 622) electrodes chemically modified with TiO 2 via atomic layer deposition were used as a model system to demonstrate the criticalness of the interfacial parasitic reactions. The suppression of the interfacial parasitic reactions effectively reduced. the hike of the cathodic surface film resistance, decreased the level of dissolution of transition metals, decreased the level of particle fragmentation, and mitigated the cation mixing of NMC 622. Finally, all of these results demonstrated that careful design of the interfacial layer by surface modifications is a key approach for improving the durability of Ni-rich NMCs under high-voltage cycling.

25 ENERGY STORAGE↗

Local lattice distortion mediated formation of stacking faults in Mg alloys

Long periodic stacking ordered phases (LPSOs), consisting of various configurations of stacking faults, play an important role in developing ultrastrong Mg alloys with moderate ductility. However, their formation mechanisms are far from clear as no apparent defects are introduced during their formation as it is commonly believed that stacking faults are induced by defects. Here, we present the atomic and electronic basis for lattice-distortion-mediated formation of stacking faults, i.e., localized face-centredcubic (FCC) structures, within a Mg-Zn-Y alloy with a hexagonal close-packed (HCP) structure. The atomic motion trajectories from ab-initio molecular dynamic simulations show that the Mg atoms occupying the nearest neighbour positions of Zn and Y solute atoms undergo a local HCP-to-FCC transition. It is revealed that a local lattice distortion caused by the solute atoms enables the Mg atoms to move and rearrange into a local FCC configuration, which is validated by high resolution scanning transmission microscopy and in-situ synchrotron X-ray diffraction. Our simulations provide profound insight into the formation mechanism of stacking faults in HCP Mg and their physical nature of phase transformations. This is not only critically important because conventional defects, such as dislocations and vacancies, are important to deformation for Mg and its alloys, but also because they serve as a potential new approach to the design of advanced Mg alloys when defects could be used to facilitate

36 MATERIALS SCIENCE↗

Methacrylated gelatin-embedded fabrication of 3D graphene-supported Co 3 O 4 nanoparticles for water splitting

In this work, we developed a general platform for the fabrication of transition metal oxide nanoparticles supported by a graphene foam (GF) by first coating it with a methacrylated gelatin (GelMA) hydrogel, which served as a 3D matrix for nanoparticle dispersion. The engineered GelMA/GF matrix was hydrophilic with good mechanical strength and high conductivity, therefore providing a good platform for the dispersion of a variety of metal/oxide precursors. Due to this platform, well-dispersed Co 3 O 4 nanoparticles with the smallest size of 3 nm assembled on the nitrogen-doped graphene foam (Co 3 O 4 /NGF). The crystalline transformation from a CoCl 2 [H 2 O] 2 precursor to Co 3 O 4 was revealed by in operando X-ray diffraction and absorption techniques. After applying Co 3 O 4 /NGF as a free-standing electrocatalyst for water splitting, the nanoparticles of size 3 nm exhibited optimal catalytic activity in alkaline media; the corresponding cell could promote water splitting at a current density of 10 mA cm -2 with only 1.63 V and exhibited excellent stability in a 25 h long-term operation. Our results demonstrate that the GelMA hydrogel-coated 3D graphene foam can be a promising platform for the design and fabrication of graphene-based multifunctional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Entropy modeling on serrated flows in carburized steels

Samples comprised of carburized steel alloys, 4615, 4720, and 10B22, were tension tested at room temperature and at a strain rate of 2 × 10 -4 s -1 . The serrated-flow behavior was modeled and analyzed, using the refined composite multiscale entropy (RCMSE) method. High energy X-ray diffraction revealed the body-centered-cubic (BCC) structure of the three alloys in the as-received condition. Moreover, Vickers-hardness experiments were performed, which showed an increase in the hardness of the alloy that corresponded to increasing impurity concentrations. Here the diffusion coefficient of carbon in the three alloys were estimated, respectively, to be 2.5 × 10 -11 m 2 /s, 5.1 × 10 -11 m 2 /s, and 2.8 × 10 -11 m 2 /s for alloys, 10B22, 4615, and 4720, respectively, which agree with the values found in the literature for α-iron. Moreover, the sample entropy, on average, increased with respect to the heating time, and, consequently, the amount of carbon that had diffused into the alloy. Finally, the above results show that the complexity of the serration behavior in the alloys studied increases with respect to the amount of carbon that has diffused into the material.

36 MATERIALS SCIENCE↗

Stabilizing the Interface between Sodium Metal Anode and Sulfide-Based Solid-State Electrolyte with an Electron-Blocking Interlayer

Sulfide-based Na-ion conductors are promising electrolytes for all-solid-state sodium batteries (ASSSBs) because of high ionic conductivity and favorable formability. However, no effective strategy has been reported for long-duration Na cycling with sulfide-based electrolytes because of interfacial challenges. Here we demonstrate that a cellulose–poly(ethylene oxide) (CPEO) interlayer can stabilize the interface between sulfide electrolyte (Na 3 SbS 4 ) and Na by shutting off the electron pathway of the electrolyte decomposition reaction. In conclusion, we achieved stable Na plating/stripping for 800 cycles at 0.1 mA cm –2 in all-solid-state devices at 60 °C.

25 ENERGY STORAGE↗

Negative thermal expansion in cubic FeFe(CN) 6 Prussian blue analogues

Negative thermal expansion (NTE) behavior is an interesting physical phenomenon, but the number of NTE materials is limited. In this study, a new NTE compound has been found, FeFe(CN) 6 Prussian blue analogue, where the average linear coefficient of thermal expansion (α l ) is –4.260 × 10 –6 K –1 between 100 and 450 K. The NTE properties and local vibration dynamics have been investigated by joint experiments of synchrotron X-ray diffraction, X-ray pair distribution function, and extended X-ray absorption fine structure spectroscopy. It has been observed that the Fe–C/Fe–N bonds expand with increasing temperature, while the unit cell shrinks in FeFe(CN) 6 . The vibration directions of both Fe–C and Fe–N prefer to be perpendicular to the linkage of Fe–C[≡]N–Fe rather than being parallel. More pieces of evidence indicate that the transverse vibrations of N atoms dominate the NTE behavior of FeFe(CN) 6 . In conclusion, the present results prove directly that the transverse thermal vibrations of C and N atoms are crucial for the occurrence of the NTE of Prussian blue analogues.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identification of Surface Structures in Pt 3 Cr Intermetallic Nanocatalysts

A precise understanding of the catalytic surface of nanoparticles is essential for relating their structure to activity. For silica-supported Pt-Cr bimetallic catalysts containing nominal Cr/Pt molar ratios of 0, 1.9, and 5.6, a fundamental difference in selectivity was observed as a function of composition for propane dehydrogenation, suggesting different surface structures. The formation of bimetallic catalysts and the phases present were confirmed by synchrotron in situ X-ray absorption spectroscopy (XAS) and X-ray diffraction (XRD) of the nanoparticle as a function of reduction temperature. With the increasing reduction temperature, there is a systematic increase in the Pt L- III edge X-ray absorption near edge structure (XANES) energy, which is consistent with the incorporation of more metallic Cr into the nanoparticles, Pt L- III edge extended X-ray absorption fine structure (EXAFS) shows that the nanoparticles are Pt rich regardless of the reduction temperature, and XRD shows the presence of both Pt and Pt 3 Cr phases at temperatures below about 700 °C. For the latter, a full Pt 3 Cr intermetallic alloy forms after reduction at 800 °C. This work additionally proposes a method for the characterization of the catalytic surface by the analysis of XAS difference spectra and XRD difference patterns of the (reduced and oxidized) catalysts. The surface analysis suggests that Pt 3 Cr formation begins at the surface, and at low reduction temperatures, a core-shell morphology is formed containing a Pt core with a Pt 3 Cr surface. By combining the XAS and XRD analyses with transmission electron microscopy (TEM) particle sizes, the thickness of the shell can be approximated. All evidence indicates that the shell thickness increases with the increasing reduction temperature until a full alloy is formed after reduction at about 800 °C but only if there is enough Cr 2 O 3 available near Pt nanoparticles to form Pt 3 Cr. Catalysts containing a full monolayer coverage of Pt 3 Cr have higher olefin selectivity (>97%) compared with partially covered Pt surfaces (88%).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of laser power on defect, texture, and microstructure of a laser powder bed fusion processed 316L stainless steel

The effect of laser power on defect characteristics, microstructure development, constituent phases, and crystallographic texture was studied on a laser powder bed fusion (L-PBF) processed 316L stainless steel. A series of cylindrical specimens were additively manufactured as a function of laser power ranging from 380 to 200W with a fixed scan speed of 300 mm/s using a selective laser melting system. The density (in terms of count, surface area, and porosity), size (mean values of major axis length, surface area, and volume), shape (aspect ratio and sphericity), and orientation (in terms of the angle between the major axis and build direction) of macroscopic defects in as-printed L-PBF cylinders were characterized using high-resolution synchrotron x-ray computed microtomography with a 0.65μm resolution. Moreover, the changes in the preferred crystallographic orientations and constituent phases were investigated using high-energy synchrotron x-ray diffraction. Finally, the melt pool shape and grain size/orientation were analyzed using metallography. The results show that the porosity increases linearly from 0.13 to 0.88% with the decrease in laser power. However, even with the decrease in laser power by about half and corresponding seven-fold increase in porosity, the 200W case can still be considered as nearly fully dense. On the other hand, with the same decrease in the laser power, the melt pool size/shape, grain size, and texture changed significantly. In conclusion, the role of energy input in the simultaneous changes in defect properties and microstructure development will be discussed.

36 MATERIALS SCIENCE↗