Engineering Papers⌕ Search

Engineering topics

Johnson, C. B.

Publications and source records attributed to Johnson, C. B..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Pressure distributions induced by elevon deflections on swept wings and adjacent end-plate surfaces at Mach 6

Surface pressure distributions are presented for regions where three-dimensional separated flow effects are prominent on swept-wing-elevon-end-plate models of 0 degree, 50 degree, and 70 degree sweepback, and with 0 degree, 10 degree, 20 degree, and 30 degree elevon deflections. Surface-oil-flow photographs and pressure distributions on the flat-plate wing, elevon, and end-plate surfaces are presented for numerous geometric variations, including various spacings between the elevon and the end plate, with and without a tip fin. The data, for a free-stream Mach number of 6 and a wing-root-chord Reynolds number of 20 x 10 to the sixth power, reveal considerably larger regions of elevon induced loads on the adjacent end-plate surface than would be anticipated by using inviscid flow analyses.

Kaufman, L. G., II↗
NASA NTRS1977

Mach 6 flowfield survey at the engine inlet of a research airplane

A flowfield survey was conducted to better define the nature of vehicle forebody flowfield at the inlet location of an airframe-integrated scramjet engine mounted on the lower surface of a high-speed research airplane to be air launched from a B-52 and rocket boosted to Mach 6. The tests were conducted on a 1/30-scale brass model in a Mach-6 20-in. wind tunnel at Reynolds number of 11,200,000 based on distance to engine inlet. Boundary layer profiles at five spanwise locations indicate that the boundary layer in the area of the forebody centerline is more than twice as thick as the boundary layer at three outboard stations. It is shown that the cold streak found in heating contours on the centerline of the forebody is caused by a thickening of the boundary layer on the centerline, and that this thickening decreases with angle of attack.

Johnson, C. B.↗
NASA NTRS1977

X-ray sensitive oblique imaging device

Instrument employs light reflecting surface (evaporated aluminum coating or minor substrate) behind phosphor screen to improve effective quantum efficiency in dual process: fraction of incoming X-rays are converted to photoelectrons at photocathode; and X-rays that pass through photocathode and thin X-ray transparent membrane enter phosphor screen.

Hallam, K. L.↗
NASA NTRS1975

A method for calculating a real-gas two-dimensional nozzle contour including the effects of gamma

A method for calculating two-dimensional inviscid nozzle contours for a real gas or an ideal gas by the method of characteristics is described. The method consists of a modification of an existing nozzle computer program. The ideal-gas nozzle contour can be calculated for any constant value of gamma. Two methods of calculating the center-line boundary values of the Mach number in the throat region are also presented. The use of these three methods of calculating the center-line Mach number distribution in the throat region can change the distance from the throat to the inflection point by a factor of 2.5. A user's guide is presented for input to the computer program for both the two-dimensional and axisymmetric nozzle contours.

Johnson, C. B.↗
NASA NTRS1975

Flight transition data for angles of attack at Mach 22 with correlations of the data

Boundary-layer transition data for angles of attack from 2.5 to 47 deg from a flight experiment with a cone that reentered at angles of attack up to 75 deg were analyzed and their local flow conditions are presented. The transition data were obtained from both acoustic and electrostatic sensors. The data from the acoustic and electrostatic sensors were correlated by use of three different sets of correlating parameters. For each set of correlating parameters, the transitional and turbulent data from the acoustic and electrostatic sensors were plotted separately. Each of the correlations was compared with a linear curve fit of previous cone-flight data at near zero angle of attack. Results indicate that the data from acoustic sensors falls below the linear curve fits to the flight data and indicates the sensitivity of the sensors. It is shown that the transition data from the electrostatic sensors tends to scatter much more than the data from the acoustic sensors. However, the data from the electrostatic sensors tends to scatter about the linear curve fits based on previous flight data.

Johnson, C. B.↗
NASA NTRS1974

Weak incident shock interactions with Mach 8 laminar boundary layers

Weak shock-wave interactions with boundary layers on a flat plate were investigated experimentally in Mach 8 variable-density tunnel for plate-length Reynolds numbers. The undisturbed boundary layers were laminar over the entire plate length. Pressure and heat-transfer distributions were obtained for wedge-generated incident shock waves that resulted in pressure rises ranging from 1.36 to 4.46 (both nonseparated and separated boundary-layer flows). The resulting heat-transfer amplifications ranged from 1.45 to 14. The distributions followed established trends for nonseparated flows, for incipient separation, and for laminar free-interaction pressure rises. The experimental results corroborated established trends for the extent of the pressure rise and for certain peak heat-transfer correlations.

Kaufman, L. G., II↗
NASA NTRS1974

A parametric study of effect of forebody shape on flow angularity at Mach 8

Flow angularity and static pressure measurements have been made on the lower surface of nine forebody models that simulate the bottom forward surface of a hypersonic aircraft. Measurements were made in an area of the forebody that represents the location of an inlet of a scramjet engine. A parametric variation of the forebody surface investigated the effect of: (1) spanwise curvature; (2) longitudinal curvature; and (3) planform shape on both flow angularity and static pressure distribution. Results of each of the three parametric variations of geometry were compared to those for the same flat delta forebody. Spanwise curvature results showed that a concave shape and the flat delta had the lowest flow angularity and lowest rate of increase in flow angularity with angle of attack. Longitudinal curvature results showed a convex surface to give the better flow at the higher angles of attack. The better of the two planform shapes tested was a convex elliptical shape. Limited flow field calculations were made at angles of attack using a three dimensional, method-of-characteristics program. In general, at all angles of attack there was agreement between data and theory.

Johnson, C. B.↗
NASA NTRS1974

Interference heating from interactions of shock waves with turbulent boundary layers at Mach 6

An experimental investigation of interference heating resulting from interactions of shock waves and turbulent boundary layers was conducted. Pressure and heat-transfer distributions were measured on a flat plate in the free stream and on the wall of the test section of the Langley Mach 6 high Reynolds number tunnel for Reynolds numbers ranging from 2 million to 400 million. Various incident shock strengths were obtained by varying a wedge-shock generator angle (from 10 deg to 15 deg) and by placing a spherical-shock generator at different vertical positions above the instrumented flat plate and tunnel wall. The largest heating-rate amplification factors obtained for completely turbulent boundary layers were 22.1 for the flat plate and 11.6 for the tunnel wall experiments. Maximum heating correlated with peak pressures using a power law with a 0.85 exponent. Measured pressure distributions were compared with those calculated using turbulent free-interaction pressure rise theories, and separation lengths were compared with values calculated by using different methods.

Johnson, C. B.↗
NASA NTRS1974

Image tube

An optical image is projected onto a planar surface of a photocathode that derives an electron beam replica of the image. A target electrode displaced relative to the photocathode so that it does not obstruct the optical image includes a planar surface for receiving and deriving an accurate replica of the electron beam image. The two planar surfaces are parallel. The electron beam image is focused on the target electrode by providing throughout a region that extends between the planar surfaces of the photocathode and receiving electrode, constant homogeneous dc electric and magnetic fields. The electric field extends in a direction perpendicular to the planar surfaces while the magnetic field extends along a straight line that intersects the photocathode and target electrode at an acute angle.

Hallam, K. L.↗
NASA NTRS1973

Interference Heating to Cavities Between Simulated RSI Tiles

Test results for full scale simulated surface insulation tiles on both the tunnel wall and in the free stream, for in-line and staggered tile orientations, are summarized as follows: (1) The staggered tile orientation has heating on the forward face which is a factor of 4.5 times higher than the heating to the forward face of the in-line tile orientation; (2) the longitudinal gap heating was the highest for the 0.3175 cm gap and the lowest for the 0.1587 cm gap; and (3) there was an order of magnitude decrease in the heating on the forward face of a spanwise gap when the gap size was decreased from 0.3175 cm to 0.1587 cm.

Johnson, C. B.↗
NASA NTRS1973

A magnetically focused image tube employing an opaque photocathode

Image converter has been developed which uses opaque photocathode for improved efficiency. Device is easier to fabricate than previous semi-transparent photocathode converters and uses compounds from Groups 3-5 that are responsive to wave-lengths between ultraviolet (approximately 100 nm) and near infrared region (approximately 1000 nm).

Johnson, C. B.↗
NASA NTRS1973

The oblique electron lens.

An oblique electron lens is described that is especially applicable to image converters and camera tubes employing flat opaque photocathodes. The use of optical lenses, corrector plates, and/or mirrors (often employed in other electron lenses designed for use with opaque photocathodes) are eliminated. The oblique electron lens is well suited to ultraviolet and vacuum ultraviolet image converters, and to image converters employing opaque negative electron affinity photocathodes. It is also possible to use this oblique electron lens for electronography. Measurements on an experimental tube show that a limiting resolution of 50 line pairs/mm is possible, but the intrinsic lens quality is believed to approach that of a conventional electromagnetic lens having uniform and colinear electric and magnetic fields.

Johnson, C. B.↗
NASA NTRS1973

Chemical nonequilibrium effects on the inviscid flow in the windward plane of symmetry of two simplified shuttle configurations

A theoretical study was made to delineate the effects of thermochemical nonequilibrium in the inviscid flow field of a representative space shuttle orbiter configuration. The study was based on experimental pressure data which was used as an input to a stream tube computer program. The pressure data from two configurations are tabulated. Calculations were restricted to the windward plane of symmetry and the calculations covered an altitude range from 200,000 to 250,000 feet at velocities of 16,000 to 24,000 feet per second respectively. Angles of attack of 20 and 40 degrees were included. The calculations show that the nonequilibrium effects are confined largely to the entropy layer expect at the highest altitude, where significant nonequilibrium effects are observed in the entire inviscid flow field.

Lordi, J. A.↗
NASA NTRS1973

An electron-lens for opaque photocathodes.

It is possible to employ opaque photocathodes in image tubes having a special electromagnetic lens without the use of special internal image-forming optical lenses or mirrors. The special electron lens, having flat object and image planes, is found to provide excellent quality electron-optical image transfer. Stray light reflection inside the tube is expected to be less serious in this electron lens than in a conventional magnetically focused image tube lens due to the offset image plane, and due to the increased absorption of photons in opaque photocathode applications.

Johnson, C. B.↗
NASA NTRS1973

Design of photoelectronic optical image sensors

The main performance goals for the image sensors are given and the design criteria for accomplishing these goals are discussed. Each functional element of the image sensors is described along with the various tradeoffs considered.

Johnson, C. B.↗
NASA NTRS1972

Heat transfer investigation of two Langley Research Center delta wing configurations at a Mach number of 10.5, volume 1

Heat transfer tests for two delta wing configurations were conducted in the hypervelocity wind tunnel. The 24-inch long models were tested at a Mach number of approximately 10.5 and at angles of attack of 20, 40, and 60 degrees over a length Reynolds number range from 5 million to 23 million on 4 May to 4 June 1971. Heat transfer results were obtained from model surface heat gage measurements and thermographic phosphor paint.

Eaves, R. H.↗
NASA NTRS1972

Heat transfer investigation of Langley Research Center transition models at a Mach number of 8, volume 2

The results are presented of a wind tunnel test program to determine aerodynamic heat transfer distributions on delta body and straight body transition models of the space shuttle. Heat transfer rates were determined by the phase-change paint technique on Stycast and RTV models using Tempilag as the surface temperature indicator. The nominal test conditions were: Mach 8, length Reynolds numbers of 5 million and 7.4 million, and angles of attack of 20, 40, and 60 deg. Model details, test conditions, and reduced heat transfer data are included. Data reduction of the phase-change paint photographs was performed by utilizing a new technique.

Matthews, R. K.↗