Engineering topics

Johnson, C. B.

Publications and source records attributed to Johnson, C. B..

At least 37 records · Page 2

NASA NTRS1984

Effect of upstream sidewall boundary layer removal on an airfoil test

Sidewall boundary layer effects were investigated by applying partial upstream sidewall boundary layer removal in the Langley 0.3-m transonic cryogenic tunnel. Over the range of sidewall boundary layer displacement thickness of these tests the influence on pressure distribution was found to be small for subcritical conditions; however, for supercritical conditions the shock position was affected by the sidewall boundary layer. For these tests (with and without boundary layer remove) comparisons with predictions of the GRUMFOIL computer code indicated that Mach number corrections due to the sidewall boundary layer improve the agreement for both subcritical and supercritical conditions. The results also show that sidewall boundary layer removal reduces the magnitude of the sidewall correction; however, a suitable correction must still be made.

Johnson, C. B.↗

NASA NTRS1983

Studies of sidewall boundary layer in the Langley 0.3 meter transonic cryogenic tunnel with and without suction

Boundary layer measurements on the sidewalls of the Langley 0.3 Meter Transonic Cryogenic Tunnel were made to determine the effectiveness of the passive boundary layer bleed system over a Reynolds number range from 20 to 200 x 10 to the sixth power per meter at Mach numbers from 0.30 to 0.76. The tunnel sidewall boundary layer displacement thickness was about 2 percent of the width of the test section without the boundary layer bleed. Measured velocity profiles correlated well with the defect law of Hama. With the boundary layer bleed equivalent to about 2 percent of the test section mass flow, the boundary layer displacement thickness reduced to about 1 percent of the test section width, which is generally considered acceptable for testing airfoils. It was also noticed that effectiveness of the bleed was nearly independent of the Mach number and Reynolds number over the range of conditions tested. A comparison of the measured suction effectiveness of the bleed with the finite difference and integral methods of boundary layer calculation showed good agreement.

Murthy, A. V.↗

NASA NTRS1983

Preliminary measurements of velocity, density and total temperature fluctuations in compressible subsonic flow

The heat transfer characteristics of a three-wire hot-wire probe operated with a constant temperature anemometer were investigated in the subsonic compressible flow regime. The sensitivity coefficients, with respect to velocity, density and total temperature, were measured and the results were used to calculate the velocity, density, and total temperature fluctuations in the test section of the Langley 0.3-m Transonic Cryogenic Tunnel (TCT). These results were extended to give estimates for fluctuations due to vorticity, sound, and entropy. In addition, attempts were made to determine the major source of disturbances in the 0.3-m TCT.

Stainback, P. C.↗

NASA NTRS1983

Investigation of the effects of upstream sidewall boundary-layer removal on a supercritical airfoil

Sidewall boundary-layer effects have been investigated by applying partial upstream sidewall boundary-layer removal in the Langley 0.3-m Transonic Cryogenic Tunnel. Over the range of sidewall boundary-layer displacement thickness of these tests the influence on pressure distributions was found to be small for subcritical conditions; however, for supercritical conditions the shock position was affected by the sidewall boundary layer. For these tests, with and without boundary-layer removal, comparisons with predictions of the GRUMFOIL computer code indicated that Mach number corrections due to the sidewall boundary layer improves the agreement for both subcritical and supercritical conditions. The results show the necessity for accounting for sidewall effects even when the top and bottom wall effects are small.

Murthy, A. V.↗

NASA NTRS1982

Recent sidewall boundary-layer investigations with suction in the Langley 0.3-m Transonic Cryogenic Tunnel

An experimental and theoretical study of the Langley 0.3-m Transonic Cryogenic Tunnel (TCT) sidewall boundary-layer with and without suction, has been made. Without suction, the boundary-layer displacement thickness at a station ahead of the model varied from about 1.6 mm to 1.3 mm over a Reynolds number range of 20 million to 200 million per m at Mach numbers from 0.30 to 0.76. Measured velocity profiles were correlated using the defect law of Hama. The boundary-layer displacement thickness decreased when suction was applied; however, after suction of about 2 percent of test section mass flow, the change in the thickness was small. A comparison of the measured suction effectiveness with finite difference and integral methods of boundary-layer calculation showed that both methods predicted the right trend over the range of suction velocities (up to a suction to free-stream velocity ratio of -0.02).

Murthy, A. V.↗

NASA NTRS1981

Methods for estimating pressure and thermal loads induced by elevon deflections on hypersonic-vehicle surfaces with turbulent boundary layers

Empirical anaytic methods are presented for calculating thermal and pressure distributions in three-dimensional, shock-wave turbulent-boundary-layer, interaction-flow regions on the surface of controllable hypersonic aircraft and missiles. The methods, based on several experimental investigations, are useful and reliable for estimating both the extent and magnitude of the increased thermal and pressure loads on the vehicle surfaces.

Kaufman, L. G., II↗

NASA NTRS1981

Measurement of recovery temperature on an airfoil in the Langley 0.3-m transonic cryogenic tunnel

Experimental measurements of recovery temperature were made on an airfoil in the Langley 0.3-m Transonic Cryogenic Tunnel at Mach numbers of 0.60 and 0.84 over a Reynolds number per meter range from about 15,000,000 to about 335,000,000. The measured recovery temperatures were considerably below those associated with ideal-gas ambient temperature wind tunnels. This difference was accentuated as the stagnation pressure increased and the total temperature decreased. A boundary-layer code modified for use with cryogenic nitrogen adequately predicted the measured adiabatic wall temperature at all conditions. A quantitative, on-line assessment of the nonadiabatic condition of a model can be made during the operation of a cryogenic wind tunnel by using a correlation for the adiabatic wall temperature which is only a function of total temperature, total pressure, and local Mach number on the model.

Johnson, C. B.↗

NASA NTRS1980

Circular-scan streak tube with solid-state readout

A circular-scan streak tube designed for use in a laser ranging system is described. Electrostatic focusing is used between the photocathode and a microchannel plate, and electrons from the microchannel plate are proximity focused onto an output phosphor screen. Electron beam deflection is achieved by driving two orthogonal sets of deflection plate assemblies in phase quadrature at a frequency of 200 MHz. The light intensity in the output beam trace is measured by using a circular Reticon array of 720 photodiodes, which is fiber-optically coupled to the output phosphor screen of the tube. Sample measurements of frequency-doubled Nd:YAG laser-pulse waveforms are given. Also the output beamwidth has been measured at the 200-MHz deflection frequency. The results suggest a limiting resolution of 33 psec for the circular-scan streak tube used for these tests.

Johnson, C. B.↗

NASA NTRS1980

Theoretical study of nonadiabatic boundary-layer stabilization times in a cryogenic wind tunnel for typical stainless steel wing and fuselage models

The time varying effect of nonadiabatic wall conditions on boundary layer properties was studied for a two dimensional wing section and an axisymmetric fuselage. The wing and fuselage sections are representative of the wing root chord and fuselage of a typical transport model for the National Transonic Facility. The analysis was made with a solid wing and three fuselage configurations (one solid and two hollow with varying skin thicknesses) all made from AISI type 310S stainless steel. The displacement thickness and local skin friction were investigated at a station on the model in terms of the time required for these two boundary layer properties to reach an adiabatic wall condition after a 50 K step change in total temperature. The analysis was made for a free stream Mach number of 0.85, a total temperature of 117 K, and stagnation pressures of 2, 6, and 9 atm.

Johnson, C. B.↗

NASA NTRS1980

A theoretical analysis of simulated transonic boundary layers in cryogenic-nitrogen wind tunnels

A theoretical analysis was made to determine the real gas effects on simulation of transonic boundary layers in wind tunnels with cryogenic nitrogen as the test gas. The analysis included laminar and turbulent flat plate boundary layers and turbulent boundary layers on a two dimensional airfoil. The results indicate that boundary layers in such wind tunnels should not be substantially different from ideal gas boundary layers at standard conditions. At a pressure of 9.0 atm, two separate effects produce deviations of real gas values from ideal gas values which are in the opposite direction from deviations at 1.0 atm and are of the same insignificant order of magnitude. Results also show that nonadiabatic boundary layers should be adequately simulated if the enthalpy ratio is the correlating parameter rather than the temperature ratio.

Adcock, J. B.↗

NASA NTRS1980

A study of nonadiabatic boundary-layer stabilization time in a cryogenic tunnel for typical wing and fuselage models

A theoretical study has been made of the time varying effect of nonadiabatic wall conditions on boundary layer properties for a two-dimensional wing section and an axisymmetric body of revolution typical of a fuselage. The wing section and body of revolution are representative of the root chord and fuselage of what is considered to be a typical size transport model for the National Transonic Facility. The transient analysis was made at a Mach number of 0.85, for stagnation pressures of 2, 6, and 9 atmospheres at several cryogenic values of total temperature for a solid wing and for three different fuselage skin thickness configurations. The analysis considered wing and fuselage sections made from stainless steel, beryllium copper, and aluminum. Examples are presented that may be used to determine the time required to reach an adiabatic condition after a change in total temperature.

Johnson, C. B.↗

NASA NTRS1979

Full-scale aircraft simulation with cryogenic tunnels and status of the National Transonic Facility

The effect of thermal and caloric imperfections in cryogenic nitrogen on boundary layers was determined to indicate that in order to simulate nonadiabatic laminar or turbulent boundary layers in a cryogenic nitrogen wind tunnel, the flight enthalpy ratio, rather than the temperature ratio, should be reproduced. The absence of significant real gas effects on both viscous and inviscid flows makes it unlikely that there will be large real gas effects on the cryogenic tunnel simulation of shock boundary layer interactions or other complex flow conditions encountered in flight. Condensation effects were studied to determine the minimum usable temperature and indicated that under most circumstances free stream Mach number rather than maximum local Mach number determines the onset of condensation effects.

Kilgore, R. A.↗

NASA NTRS1979

Pressure and thermal distributions on wings and adjacent surfaces induced by elevon deflections at Mach 6

Surface pressure distributions and heat transfer distributions were obtained on wing half-models in regions where three dimensional separated flow effects are prominent. Unswept and 50 deg and 70 deg swept semispan wings were tested, for trailing-edge-elevon ramp angles of 0 deg, 10 deg, 20 deg, and 30 deg, with and without cylindrical and flat plate center bodies and with and without various wing-tip plates and fins. The data, obtained for a free stream Mach number of 6 and a wing-root-chord Reynolds number of 18.5 million, reveal considerably larger regions of increased pressure and thermal loads than would be anticipated using non-separated flow analyses.

Kaufman, L. G., II↗

NASA NTRS1979

High speed interference heating loads and pressure distributions resulting from elevon deflections

Effects of elevon-induced three-dimensional shock-wave turbulent boundary-layer interactions on hypersonic aircraft surfaces are analyzed. Detailed surface pressure and heating rate distributions obtained on wing-elevon-fuselage models representative of aft portions of hypersonic aircraft are compared with analytical and experimental results from other sources. Examples are presented that may be used to evaluate the adequacy of current theoretical methods for estimating the effects of three-dimensional shock-wave turbulent boundary-layer interactions on hypersonic aircraft surfaces.

Johnson, C. B.↗

NASA NTRS1979

Full scale aircraft simulation with cryogenic tunnels and status of the National Transonic Facility

The paper reviews the results of some of the real-gas studies made at Langley that are directly related to establishing the range of operating conditions that can be used in a cryogenic nitrogen wind tunnel and still be assured of valid full-scale simulation. Consideration is given to the important aerodynamic features, anticipated performance capability, status of construction, and projected operating data for the National Transonic Facility.

Kilgore, R. A.↗

NASA NTRS1978

Heat transfer distributions induced by elevon deflections on swept wings and adjacent surfaces at Mach 6

Surface heat transfer distributions are presented for swept wing semispan models having trailing edge elevon ramp angles of 0, 10, 20, and 30 degrees. The wing sweepback angles are 0, 50, and 70 degrees. The models have attachable cylindrical and flat plate center bodies and various attachable wing-tip fins. The data, obtained for a 0 degree angle of attack, a free stream Mach number of 6, and a wing root chord Reynolds number of about 17,000,000, reveal considerably larger regions of elevon induced thermal loads on adjacent surfaces than would be suggested by fully attached flow analyses.

Johnson, C. B.↗

NASA NTRS1978

Inlet boundary-layer shapes on four aircraft forebodies at Mach 6

Boundary-layer shape measurements at the engine inlet on four different hypersonic aircraft forebody designs (with no engine on the forebody) are reported. The measurements provide a qualitative assessment of the effectiveness of various forebody geometries as engine inlet precompression surfaces. The designs, tested in a hypersonic tunnel at Mach 6 and a nominal freestream Reynolds number of 30,500,000, included a semiconical forebody, a configuration similar to a slab delta wing, a conical nose blended into a flat surface, and a conical, complex forebody shape. Boundary layer height as a function of forebody compression is shown for each design.

Lawing, P. L.↗

NASA NTRS1977

Heat-transfer and pressure measurements on a simulated elevon deflected 30 deg near flight conditions at Mach 7

Heat transfer rates and pressures were obtained on an elevon plate (deflected 30 deg) and a flat plate upstream of the elevon in an 8 foot high-temperature structures tunnel. The flight Reynolds number and flight total enthalpy for altitudes of 26.8 km and 28.7 km at Mach seven were duplicated. The heat transfer and pressure data were used to establish heating and pressure loads. The measured heating was compared with several theoretical predictions, and the closest agreement obtained with a Schultz-Grunow reference enthalpy method of calculation.

Johnson, C. B.↗