Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure and mechanical properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Microstructure, Mechanical Properties, Hot-Die Forming, and Joining of 47XD Gamma TiAl Rolled Sheets

The microstructure and mechanical properties, along with the hot-die forming and joining of Ti-47Al-2Nb-2Mn-0.8 vol% TiB, sheets (known as 47XD), produced by a low-cost rolling process, were evaluated. A near-gamma microstructure was obtained in the as-rolled condition. The microstructures of heat-treated sheets ranged from a recrystallized equiaxed near-gamma microstructure at 1,200 to 1,310 C, to a duplex microstructure at 1,350 C, to a fully lamellar microstructure at 1,376 C. Tensile behavior was determined for unidirectionally rolled and cross-rolled sheets for room temperature (RT) to 816 C. Yield stress decreased gradually with increasing deformation temperature up to 704 C; above 704 C, it declined rapidly. Ultimate tensile strength exhibited a gradual decrease up to 537 C before peaking at 704 C, followed by a rapid decline at 816 C. The modulus showed a gradual decrease with temperature, reaching approximately 72% of the RT value at 816 C. Strain to failure increased slowly from RT to 537 C; between 537 C and 704 C it exhibited a phenomenal increase, suggesting that the ductile-brittle transition temperature was below 704 C. Fracture mode changed from transgranular fracture at low temperature, to a mixture of transgranular and intergranular fracture at intermediate temperature, to ductile fracture at 816 C, coupled with dynamic recrystallization at large strains. Creep rupture response was evaluated between 649 and 816 C over the stress range of 69 to 276 MPa. Deformation parameters for steady-state creep rate and time-to-rupture were similar: activation energies of approximately 350 kJ/mol and stress exponents of approximately 4.5. Hot-die forming of sheets into corrugations was done at elevated temperatures in vacuum. The process parameters to join sheets by diffusion bonding and brazing with TiCuNi 70 filler alloy were optimized for test coupons and successfully used to fabricate large truss-core and honeycomb structures. Nondestructive evaluation methods, e.g., ultrasonic C-scans and thermography along with metallography, were used to characterize bond quality. Microstructural evaluation during heat treatment, identification of phases at the braze/matrix interface, determination of shear strengths of brazed joints, and deformation mechanisms during tensile and creep processes will be discussed.

Das, G.↗
DOE OSTI2025

Laser powder bed fusion of ODS Fe–Cr–Al (0.3Zr, 0.3Y 2 O 3 ): Unveiling processing-microstructure- mechanical property relationships

Here, this study investigates the fabrication of oxide dispersion strengthened (ODS) Fe-Cr-Al alloys via laser powder bed fusion (LPBF) with strategic additions of 0.3 wt% Zr and 0.3 wt% Y 2 O 3 for enhanced mechanical performance in nuclear applications. Systematic processing parameter optimization yielded three distinct conditions: one low-density product with significant defects and two near-full-density materials with improved consolidation. Comprehensive characterization confirmed single-phase α-ferrite matrix formation with successful incorporation of Y-, Zr-, O-, and C-rich precipitates characteristic of ODS alloys. However, precipitate density remained low (∼10 7 cm −3 ), resulting in sink strength values substantially below optimal levels for radiation resistance. Microhardness values (mid-200s HV) correlated inversely with grain size following the Hall-Petch relationship, indicating grain boundary strengthening as the dominant mechanism rather than precipitation strengthening. The optimized processing conditions achieved excellent mechanical properties with room temperature yield strength of approximately 500 MPa and 30 % elongation, demonstrating superior strength-ductility synergy compared to other additively manufactured ODS materials and performance consistent with literature values for LPBF-processed ODS-FeCrAl alloys. This investigation reveals both the potential and limitations of LPBF processing for ODS Fe-Cr-Al alloys. While successful defect-free fabrication was achieved, results highlight the critical need for systematic optimization of processing parameters and post-processing heat treatments to enhance precipitate density for effective dispersion strengthening and radiation resistance while maintaining additive manufacturing advantages.

Additive manufacturing↗
DOE OSTI2025

Microstructure & Mechanical Properties of Scaled Thermally Aged LPBF 316H SS Builds

As part of the US Department of Energy’s Advanced Materials and Manufacturing Technologies program’s mission to accelerate qualification of advanced manufacturing pathways for nuclear applications, laser powder bed fusion (LPBF) 316H stainless steel (SS) has been selected as a model system to develop a rapid code case framework. This effort directly addresses the grand challenges of (1)expanding the limited portfolio of materials currently codified for elevated-temperature nuclear structural service under Section III, Division 5of the American Society of Mechanical Engineers’ Boiler and Pressure Vessel Code; and (2) significantly reducing qualification timelines that traditionally exceed a decade. The strategic importance of LPBF 316H lies in its immediate industrial relevance, existing data foundation from wrought 316H, and alignment with ongoing code case development for LPBF 316L.Prior work revealed accelerated precipitation of deleterious secondary phases and reduced creep ductility in as-printed LPBF 316H. Building on that prior research, FY2025activities focused on establishing an understanding of the key failure mechanisms of crept 316H specimens to aid in code case development and on evaluating stress relief (SR) parameters on the high-temperature performance and thermal aging-induced degradation of tensile and fracture behavior in LPBF316H.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Microstructure-mechanical property relationships for Al-Cu-Li-Zr alloys with minor additions of cadmium, indium or tin

Minor amounts of cadmium, indium or tin were added to a baseline alloy with the nominal composition of Al-2.4Cu-2.4Li-0.15Zr. These elements were added in an attempt to increase the age-hardening response of the material such that high strengths could be achieved through heat-treatment alone, without the need for intermediate mechanical working. The alloy variant containing indium achieved a higher peak hardness in comparison to the other alloy variations, including the baseline material, when aged at temperatures ranging from 160 C to 190 C. Tensile tests on specimens peak-aged at 160 indicated the yield strength of the indium-bearing alloy increased by approximately 15 percent compared to that of the peak-aged baseline alloy. In addition, the yield strength obtained in the indium-bearing alloy was comparable to that reported for similar baseline material subjected to a 6 percent stretch prior to peak-aging at 190 C. The higher strength levels obtaied for the indium-bearing alloy are attributed to increased number densities and homogeneity of both the T1 and theta-prime phases, as determined by TEM studies.

Blackburn, L. B.↗
NASA NTRS2003

Microstructure and Mechanical Properties of Extruded Gamma Microstructure Met PX

A gamma TiAl alloy with a high Nb content is being assessed as a compressor blade material. The microstructure and mechanical properties of extruded Ti-45Al-X(Nb,B,C) (at.%) were evaluated in both an as-extruded condition and after a lamellar heat treatment. Tensile behavior of both as-extruded and lamellar heat treated specimens was studied in the temperature range of RT to 926 C. In general, the yield stress and ultimate tensile strength reached relatively high values at room temperature and decreased with increasing deformation temperature. The fatigue strength of both microstructures was characterized at 650 C and compared to a baseline TiAl alloy and to a Ni-base superalloy. Tensile and fatigue specimens were also exposed to 800 C for 200 h in air to evaluate the alloy's environmental resistance. A decrease in ductility was observed at room temperature due to the 800 C. exposure but the 650 C fatigue properties were unaffected. Compressive and tensile creep testing between 727 and 1027 C revealed that the creep deformation was reproducible and predictable. Creep strengths reached superalloy-like levels at fast strain rates and lower temperatures but deformation at slower strain rates and/or higher temperature indicated significant weakening for the as-extruded condition. At high temperatures and low stresses, the lamellar microstructure had improved creep properties when compared to the as-extruded material. Microstructural evolution during heat treatment, identification of various phases, and the effect of microstructure on the tensile, fatigue, and creep behaviors is discussed.

Draper, S. L.↗
DOE OSTI2025

Directed energy deposition of radially functionally graded nickel based superalloys IN625 and IN738: Microstructure and mechanical properties

This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.

Additive manufacturing↗
NASA NTRS1984

Ultrasonic nondestructive evaluation, microstructure, and mechanical property interrelations

Ultrasonic techniques for mechanical property characterizations are reviewed and conceptual models are advanced for explaining and interpreting the empirically based results. At present, the technology is generally empirically based and is emerging from the research laboratory. Advancement of the technology will require establishment of theoretical foundations for the experimentally observed interrelations among ultrasonic measurements, mechanical properties, and microstructure. Conceptual models are applied to ultrasonic assessment of fracture toughness to illustrate an approach for predicting correlations found among ultrasonic measurements, microstructure, and mechanical properties.

Vary, A.↗
NASA NTRS2005

Mechanical Properties and Microstructure Investigation of Lead Free Solder

While the electronics industry appears to be focusing on Sn-Ag-Cu as the alloy of choice for lead free electronics assembly, ,the exact composition varies by geographic region, supplier and user. Add to that dissolved copper and silver from the printed circuit board traces and surface finish, and there can be significant variation in the final solder joint composition. A systematic study of the mechanical and microstructural properties of Sn-Ag-Cu alloys with Ag varying from 2wt% to 4wt% and Cu varying from 0.5wt% to lSwt%, was undertaken in this research study. Different sample preparation techniques (water quenched, oil quenched and water quenched followed by reflow) were explored and the resulting microstructure compared to that of a typical reflowed lead free chip scale package (CSP) solder joint. Tensile properties (modulus, 0.2% yield strength and the ultimate tensile strength) and creep behavior of selected alloy compositions (Sn-4Ag-1 X u , Sn-4Ag-OSCu, Sn- 2Ag-1 X u , Sn-2Ag-OSCu, Sn-3.5Ag-O.SCu) were determined for three conditions: as- cast; aged for 100 hours at 125OC; and aged for 250 hours at 125OC. There was no significant difference in Young's Modulus as a function of alloy composition. After an initial decrease in modulus after 100 hours at 125"C, there was an insignificant change with further aging. The distribution of 0.2% strain yield stress and ultimate tensile strength as a function of alloy composition was more significant and decreased with aging time and temperature. The microstructures of these alloys were examined using light and scanning electron microscopy (LM and SEM) respectively and SEM based energy dispersive x-ray spectroscopy (EDS). Fracture surface and cross-section analysis were performed on the specimens after creep testing. The creep testing results and the effect of high temperature aging on mechanical properties is presented for the oil quenched samples. In general the microstructure of oil quenched specimen exhibited a eutectic region of Sn with moderately dispersed Ag3Sn intermetallic, surrounded by a dendritic Sn-rich phase. The SEM images of the fracture surface indicated the presence of a tough shear surface at the initial cavity break area and a break line in the middle of specimen along the failure direction. A hyperbolic-sine creep model was adopted and used to fit the creep experiment data. The effect on the mechanical properties by adding the quaternary element bismuth to the Sn-3.5Ag-0.8Cu alloy was measured and compared with the mechanical properties of the ternary alloys. The results of this research study provide necessary data for the modeling of solder joint reliability for a range of Sn-Ag-Cu compositions and a baseline for evaluating the effects of subsequent quaternary additions.

Wang, Qing↗
NASA NTRS1987

Effect of LID (Registered) processing on the microstructure and mechanical properties of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo titanium foil-gauge materials

A study was undertaken to determine the mechanical properties and microstructures resulting from Liquid Interface Diffusion (LID -Registered) processing of foil-gauge specimens of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo coated with varying amounts of LID material. In addition, the effects of various elevated temperature exposures on the concentration profiles of the LID alloying elements were investigated, using specimens with a narrow strip of LID material applied to the surface. Room and elevated temperature tensile properties were determined for both coated and uncoated specimens. Optical microscopy was used to examine alloy microstructures, and scanning electron microscopy to examine fracture surface morphologies. The chemical concentration profiles of the strip-coated specimens were determined with an electron microprobe.

Balckburn, Linda B.↗
NASA NTRS1992

Sintering time and atmosphere influences on the microstructure and mechanical properties of tungsten heavy alloys

The present paper traces the microstructure and mechanical property variations vs sintering time under conditions where the atmosphere was adjusted to suppress pore generation. Attention is given to tracing the mechanical property links to the grain size under optimized sintering conditions. The optimal cycle is used to sinter two heavy alloy compositions (88 and 95 wt pct W) for times up to 600 minutes at 1480 C. The 88-pct-W samples slumped, but the 95-pct-W samples were fully densified and suitable for tensile testing. At long sintering times, the tungsten grains flattened and the tungsten contiguity decreased, indicating a transition to low-energy configurations for the solid-liquid interfaces. The cube of the mean grain size varied linearly with the isothermal sintering time. This allowed the determination of grain size effects on mechanical properties, showing a decreasing yield strength with increasing time in agreement with the Hall-Petch behavior. The tensile strength and elongation were highest for sintering times from 30 to 90 min, reflecting a minimum in the residual porosity.

German, R. M.↗
NASA NTRS1994

Microstructure and Mechanical Properties of Reaction-Formed Silicon Carbide (RFSC) Ceramics

The microstructure and mechanical properties of reaction-formed silicon carbide (RFSC) ceramics fabricated by silicon infiltration of porous carbon preforms are discussed. The morphological characterization of the carbon preforms indicates a very narrow pore size distribution. Measurements of the preform density by physical methods and by mercury porosimetry agree very well and indicate that virtually all of the porosity in the preforms is open to infiltrating liquids. The average room temperature flexural strength of the RFSC material with approximately 8 at.% free silicon is 369 +/- 28 MPa (53.5 +/- 4 ksi). The Weibull strength distribution data give a characteristic strength value of 381 MPa (55 ksi) and a Weibull modulus of 14.3. The residual silicon content is lower and the strengths are superior to those of most commercially available reaction-bonded silicon carbide materials.

Singh, M.↗
DOE OSTI2025

Investigation of MgO additives on microstructure and properties of thin LLZO electrolytes for all-solid-state batteries

To realize high-energy density lithium lanthanum zirconate (LLZO)-based solid-state batteries (SSB), LLZO electrolytes should be fabricated with low thickness and high mechanical strength. An effective strategy for strengthening ceramic materials is to use additives. Here, we employed MgO nanopowders and fibers as additives for the thin LLZO electrolyte in order to improve the mechanical strength. The microstructure, mechanical properties, and electrochemical properties are characterized to investigate the effects of adding MgO and sintering time. The MgO remains at grain boundaries after sintering, making the microstructure of LLZO fine and uniform. The mechanical strength of the MgO-added LLZO was enhanced by more than 60% while maintaining high ionic conductivity (1 × 10 -4 S cm -1 ) at room temperature. Li symmetric cells using the MgO fiber–LLZO and MgO powder–LLZO exhibit 2 and 3 times higher critical current density (CCD) than those of pure LLZO, and a solid-state full cell exhibits stable cycling performance. Further, these results demonstrate that the use of MgO nanopowder or fiber as an additive for thin LLZO is beneficial for high-current density cycling, by improving mechanical properties and microstructure.

25 ENERGY STORAGE↗
DOE OSTI2025

Effects of magnetic field assisted heat treatment on the microstructure and mechanical properties of Fe-0.63 %C alloy

This study investigates the influence of an applied magnetic field on the microstructural evolution and mechanical properties of hypoeutectoid steels subjected to heat treatment. Tensile tests and microstructural analysis were performed on samples processed under varying magnetic field strengths (0 T, 5 T, and 9 T) and different austenitization incubation times. The results indicate that the application of a magnetic field alters the fraction of proeutectoid ferrite phase without changing the cooling rates and heat treatment process. Additionally, pearlite microstructural features such as lamellar spacing and misorientation angles exhibit variations under different field strengths. While the pearlite nodule diameter remains largely unaffected, an increase in percentage elongation and strength is observed in the 5 T treated sample, attributed to changes in microstructural features with the magnetic field. Additionally, the percentage elongation is reduced in the samples heat treated with reduced austenitization incubation times. The study further demonstrates that low-angle misorientations increased in the samples taken parallel to the magnetic field direction, influencing the mechanical response. These findings suggest that applying a magnetic field during heat treatment provides an additional driving force for phase transformations, offering a manufacturing process for tailoring microstructures and optimizing mechanical properties. Moreover, integrating magnetic fields in heat treatment processes has potential benefits in energy efficiency.

High magnetic field↗
NASA NTRS1982

Influence of cobalt, tantalum, and tungsten on the microstructure and mechanical properties of superalloy single crystals

The influence of Co, Ta, and W on the microstructure and mechanical properties of nickel base super-alloy single crystals was investigated. A matrix of alloys was based on Mar-M 247 stripped of C, B, Zr, and Hf. The microstructures of the alloys were examined using optical and electron microscopy, phase extraction, X-ray diffraction, and differential thermal analysis. Tensile and creep-rupture tests were performed at 1000 C. An increase in tensile and creep strength resulted when Co was removed from alloys containing high refractory metal contents, but Co effects were negligible for alloys with lower refractory metal levels. In the composition range studied, W was more effective than Ta in increasing the creep resistance. The mechanical properties are discussed in relation to the microstructures of the alloys.

Nathal, M. V.↗