SEARCH · Engineering Papers

Results for “freeze tape casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

9 records

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Freeze Tape Casting Electrode with Bilayered Architecture for High-Performance Lithium-Ion Batteries

A facile freeze tape casting (FTC) strategy is utilized to prepare bilayered 4 mAh cm –2 high-loading LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathodes. The bottom layer is a conventional nonaqueous electrode, which has a dense structure for high-energy purposes. Further, the top layer is prepared by the proposed FTC, exhibiting a porous feature for high-power requirement. With the assistance of FTC, the bilayered electrodes successfully deliver enhanced rate and cyclic performance due to the improved lithium-ion diffusion kinetics and pathways. Therefore, the proposed FTC strategy and its delivered electrodes are promising for energy- and power-density lithium-ion batteries, potentially enlightening the research and development of lithium-ion battery manufacturing.

25 ENERGY STORAGE↗

DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗

DOE OSTI2019

Scalable Freeze-Tape-Casting Fabrication and Pore Structure Analysis of 3D LLZO Solid-State Electrolytes

Nonflammable solid-state electrolytes can potentially address the reliability and energy density limitations of lithium-ion batteries. Garnet-structured oxides such as Li 7 La 3 Zr 2 O 12 (LLZO) are some of the most promising candidates for solid-state devices. Here, three-dimensional (3D) solid-state LLZO frameworks with low tortuosity pore channels are proposed as scaffolds, into which active materials and other components can be infiltrated to make composite electrodes for solid-state batteries. To make the scaffolds, we employed aqueous freeze tape casting (FTC), a scalable and environmentally friendly method to produce porous LLZO structures. Using synchrotron radiation hard X-ray microcomputed tomography, we confirmed that LLZO films with porosities of up to 75% were successfully fabricated from slurries with a relatively wide concentration range. The acicular pore size and shape at different depths of scaffolds were quantified by fitting the pore shapes with ellipses, determining the long and short axes and their ratios, and investigating the equivalent diameter distribution. The results show that relatively homogeneous pore sizes and shapes were sustained over a long range along the thickness of the scaffold. Additionally, these pores had low tortuosity and the wall thickness distributions were found to be highly homogeneous. These are desirable characteristics for 3D solid electrolytes for composite electrodes, in terms of both the ease of active material infiltration and also minimization of Li diffusion distances in electrodes. The advantages of the FTC scaffolds are demonstrated by the improved conductivity of LLZO scaffolds infiltrated with poly(ethylene oxide)/lithium bis(trifluoromethanesulfonyl)imide (PEO/LITFSI) compared to those of PEO/LiTFSI films alone or composites containing LLZO particles.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Effect of isotropic and anisotropic porous microstructure on electrochemical performance of Li ion battery cathodes: An experimental and computational study

Liquid electrolyte mass transport is a major limitation affecting high-power Li ion batteries. Fast discharging causes Li salt depletion in the current collector region of the cathode which produces overpotential in the electrolyte and consequently a drop of cell voltage to below the cut-off voltage, especially at higher electrode thickness and discharge rate. In this study, through experiment and simulation, we have investigated the effect of electrode thickness, mass loading, discharge rate and tortuosity on electrolyte mass transport and final derived areal capacity and specific energy for electrodes having isotropic (normal tape casting) and anisotropic (freeze tape casting) porous microstructure. Furthermore, the macroporous channels in freeze tape cast electrodes facilitate Li salt transport and reduce the Li salt mass transport limitations even at high electrode thickness and discharge rates, and high electrode tortuosity. In our results, computer simulations show that freeze tape cast electrodes may be fully discharged up to 750 μm thickness at 1 C rate compared to 300 μm for normal tape cast electrodes with the same mass loading. Freeze tape cast electrodes also show stable maximum areal capacity for C rates about double the maximum C rates of their normal tape cast electrode counterparts with the same mass loading.

25 ENERGY STORAGE↗

DOE OSTI2019

All-Solid-State Batteries Using Rationally Designed Garnet Electrolyte Frameworks

Functioning bulk-type all-solid-state batteries in a practical form factor with composite positive electrodes, using Al-substituted Li 7 La 3 Zr 2 O 12 (LLZO) as the solid electrolyte, have been demonstrated for the first time. The devices incorporate bilayers composed of dense LLZO membranes and porous LLZO scaffolds infiltrated with LiNi 0.6 Mn 0.2 Co 0.2 O 2 and other components as positive electrodes, combined with lithium anodes. The porous scaffolds are prepared using an easily scaled freeze-tape-casting method. The unidirectional pores of the scaffold facilitate infiltration of cathode components and shorten lithium ion diffusion path lengths, while the addition of a soft ionically conductive solid to the scaffold ensures good contact among the components.

25 ENERGY STORAGE↗

DOE OSTI2023

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗

DOE OSTI2020

(Invited) All-Solid-State Batteries Using Li 7 La 3 Zr 2 O 12 Garnet Electrolyte Framework

All-solid-state batteries (ASSB) using LLZO (variants of Li 7 La 3 Zr 2 O 12 ) garnet solid electrolyte with lithium metal anode potentially offer higher energy density and improved safety. Rational design of cell architecture as well as manufacturing scalability are key aspects to consider as the technology readiness level advances. A thick composite cathode layer attached to a thin solid electrolyte layer is desirable to obtain superior energy densities. Furthermore, the architecture within the composite cathode may be engineered to contain directional conduction paths of lithium ions or electrons for enhanced rate capabilities. Here, we demonstrate a functioning bulk-type LLZO based all-solid-state battery with a practical form factor incorporating the above described design concepts. Freeze-tape-casting (FTC), a scalable and environmentally friendly ceramic processing method, is used to construct 3D porous LLZO scaffolds composed of vertical arrays of LLZO walls. The thin solid-electrolyte layer is fabricated by tape-casting (TC). By sintering the stacks of FTC and TC green tapes, porous/dense bilayers and porous/dense/porous trilayers of LLZO frameworks are obtained. An ASSB was constructed using a porous/dense bilayer by infiltrating LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode powder and carbon black into the porous layer and adhering lithium metal foil to the dense side. We find it crucial to introduce a plastic crystal based soft solid electrolyte to the porous layer to electrochemically connect all cathode components, obviating the need for co-sintering to establish contact. The soft nature of the plastic crystal based solid-electrolyte may be able to accommodate the volume change of the cathode material as it cycles. In this device, which contained no liquid component, the initial discharge capacities were similar to those observed in a lithium ion battery configuration using the same cathode powder at C/10 rates.

25 ENERGY STORAGE↗

DOE OSTI2025

Development of a scalable, robust electrocatalytic technology for conversion of CO 2 to formic acid via microstructured materials

This project was funded by the Bioenergy Engineering for Product Synthesis (BEEPS) program under the Funding Opportunity Announcement (FOA) DE-FOA-0001916 Topic Area 5 “Rewiring Carbon Utilization”. This FOA sought projects that would electrocatalytically reduce CO 2 to a carbon intermediate and then upconvert to a multi-carbon product or fuel via non-photosynthetic biological system engineering. The project sought to combine the expertise of OCO Chem, whose chief scientist had previously developed an efficient electrocatalytic reactor for conversion of CO 2 to formate with potential to scale, Montana State University investigators who had recently patented a method for laterally grading membranes with the potential of improving reactant distribution and more uniform efficiency across membrane-based reactors, and University of South Florida which had recently discovered a novel C-C bond forming reaction not known to naturally occur in biological systems and which uses C1 substrates and circumvents the central microbial metabolism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Optimization of catholyte for halide-based all-solid-state batteries

Halide solid electrolytes gain significant attention due to their high ionic conductivity, low processing temperature, dry air compatibility, and high-voltage stability. However, low cathode active material (CAM) loading in the composite cathode constrains the realization of high energy density for halide-based all-solid-state batteries. In this study, three halide materials, raw Li 3 YBrCl 5 (LYBC-R, <30μm), milled LYBC (LYBC-M, <5 μm) and freeze-dried Li 3 InCl 6 (LIC, <500 nm), were used as catholytes, combined with LYBC-M as the electrolyte and LiIn alloy as the anode. The CAM:catholyte ratio was investigated as well as stack pressure and operating temperature. Our study demonstrates that particle size of the catholyte plays an important role only for high CAM loading or high C-rate cycling. At moderate CAM loading (65 and 70wt% LiNi 0.83 Mn 0.06 Co 0.11 O 2 ) and 0.1 C-rate, all the three catholytes perform well, providing initial discharge capacities >177 mAh/g. At high CAM loading (85wt%) and 0.1 C-rate, a cathode with the nano-scale LIC catholyte provides discharge capacity of 175 mAh/g, while the larger particle size catholytes suffer significantly reduced capacity. Both LYBC and LIC catholytes provided capacity retention >80% after 200 cycles at 0.5C. These results imply that cathode particle size is critically important for performance at high CAM loading. Furthermore, both electrolyte and cathode were tape cast to scale up size and prepare realistic layer thicknesses. A small amount of binder was used in both layers, to balance the electrochemical performance and mechanical properties. Further, the discharge capacity of a tape cell was 152mA h/g at 0.1C with a capacity retention of 81.8% after 20 cycles at 0.5C. The results demonstrate the excellent performance of LYBC as an electrolyte, and provide guidance for halide-based cathode design.

25 ENERGY STORAGE↗