Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “arc radius”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

PETN spark-gap detonators

The well-developed theory of Lorentz plasma that is dominated by electron–ion interactions is used to calculate the PETN arc characteristics. The spark-gap discharge current is a ramp with 10 to 25 ns rise time to peak and remaining constant subsequently. The approximate formulas for the arc channel conductivity, arc temperature, arc radius, and shock pressure from the arc are obtained from a system of nonlinear ordinary differential equations, which is the similarity solution of hydrodynamic equations similar to the Braginskii approximation. These arc parameters are given for the peak current ranging from 100 A to 1000 A and with different rise times. Representative cases are compared to the nonlinear ordinary differential equation code results. The shock pressures at the peak current are comparable to those from a typical commercial EBW bridgewire burst reported in the literature; the arc radius at the peak current is comparable to a typical bridgewire diameter of 0.0375 mm (e.g., RISI detonators, RP-1, and RP-80). The relevant Pop-Plot for low-density PETN is converted into an empirical detonation criterion, which is applicable to explosives subject to shocks of variable pressure. Finally, this criterion is then used to determine the detonation thresholds, which are comparable with test data obtained by Tucker, et al.

42 ENGINEERING↗
DOE OSTI2022

Improved Understanding of Zircaloy Hydrogen Pickup Mechanisms in BWRs. NSUF Report (Final Report)

Using an instrumented autoclave operating at 288°C and 1100 psi, electrical impedance spectroscopy (EIS) measurements were taken from three neutron irradiated fuel channel samples (Zircaloy-2 and Zircaloy-4). The three high priority fuel channel samples were tested at 288°C using a simulated PWR water with the AC frequency range extending down through 10 -4 Hz, with corresponding DC measurements to validate the resistance measurements. EIS measurements were also taken at room temperature using a simulated PWR water from four neutron irradiated fuel channel samples (Zircaloy-2 and Zircaloy-4). and four water rod samples (Zircaloy-2). EIS measurements were also performed on unirradiated Zircaloy-2 tubes that were previously oxidized in autoclaves at various temperatures for different time durations to obtain oxide layers of different thicknesses. These experiments proved to be more challenging than anticipated because of the small size of the samples, which required development of fixtures to allow valid testing of the materials, some of which are radioactive, under pressure and temperature. Equivalent circuits were used to model the data. Some samples resulted in Nyquist plots where the arcs were too close to each other resulting in the inability to separate the different oxide morphological thicknesses. Microstructural characterization in the form of optical microscopy, scanning electron microscopy and (scanning) transmission electron microscopy was performed to document the microstructural features of the oxidized Zr-2 and Zr-4 samples (oxide and metal/oxide interface) and to interpret the EIS results. At the start of this work, it was assumed that despite the laminar cracks and porosity visible in both optical and SEM, the oxide scale is dense near the metal, effectively preventing the water from contacting the metal directly. While it is generally accepted that the large laminar cracks pores allow the water to percolate into the oxide film, it is unknown just how deep it can go, and how interconnected is the porosity, which will dictate how much the porosity is connected electrically to the water within the oxide scale. The EIS results demonstrated that there is in fact a distribution of oxide thicknesses over the various samples, and within each material condition, that are communicating to the liquid. This is derived from the fact that Nyquist plots have an arc radius whose center point is often below the Z’ axis, implying that instead of a single oxide thickness, these oxides have a distribution of thicknesses. This distribution of thicknesses produces arcs that are not clearly separable in most of the samples.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Innovative large overbraided carbon fiber composite beams in historical Friendship Bell Pavilion

The International Friendship Bell Pavilion located in the City of Oak Ridge, Tennessee symbolizes the spirit of the peace and friendship shared by the city of Oak Ridge and city of Naka, Japan. The Bell Pavilion features an 8000-pound bronze cast bell along with futuristic materials and advanced manufacturing technologies. The team has developed innovative overbraided carbon fiber arched beams in conjunction with the bronze bell. Carbon fiber was utilized in these beams because of its lightweight, strong, stiff, and durable characteristics. A sandwich design used a high-performance foam core, overbraided with triaxial carbon fibers. This is the world’s largest overbraided composite structure for parks and recreation. For the first time in such an application, 17 free floating, 33-foot (10 m) long arched carbon fiber composite beams cantilever from a central concrete-steel superstructure over the bronze bell. The arc radius of the bottom of each beam is uniquely different giving an appearance of an open dome when standing underneath the structure.

Parks and Recreation↗
DOE OSTI2020

Experimental and modeling analysis of detonation in circular arcs of the conventional high explosive PBX 9501

We examine the diffraction dynamics of a two-dimensional (2D) detonation in a circular arc of the conventional HMX-based, high performance, solid explosive PBX 9501, for which the detonation reaction zone length scale is estimated to be of the order of 100–150 µm. In this configuration, a steady propagating detonation will develop, sweeping around the arc with constant angular speed. We report on results from three PBX 9501 arc experiments, exploring the variation in linear speed on the inner and outer arc surfaces for the steady wave along with the structure of the curved detonation front, as a function of varying inner surface radius and arc thickness. Comparisons of the properties of the motion of the steady wave for each arc configuration are then made with a spatially-distributed PBX 9501 reactive burn model, calibrated to detonation performance properties in a 2D planar slab geometry. We show that geometry-induced curvature of the detonation near the inner arc surface has a significant effect on the detonation motion even for conventional high explosives. We also examine the detonation driving zone structure for each arc case, and thus the subsonic regions of the flow that determine the influence of the arc geometry on the detonation propagation. In addition, streamline paths and reaction progress isolines are calculated. Overall, we conclude that a common approximation for modeling conventional high explosive detonation, wherein the shock-normal detonation speed is assumed equal to the Chapman–Jouguet speed, can lead to significant errors in describing the speed at which the detonation propagates.

42 ENGINEERING↗
DOE OSTI2021

Core Mass Estimates in Strong Lensing Galaxy Clusters: A Comparison between Masses Obtained from Detailed Lens Models, Single-halo Lens Models, and Einstein Radii

The core mass of galaxy clusters is both an important anchor of the radial mass distribution profile and probe of structure formation. With thousands of strong lensing galaxy clusters being discovered by current and upcoming surveys, timely, efficient, and accurate core mass estimates are needed. Here, we assess the results of two efficient methods to estimate the core mass of strong lensing clusters: the mass enclosed by the Einstein radius (M(<θ E ) where θ E is approximated from arc positions; Remolina González et al. 2020), and single-halo lens model (M SHM ; Remolina González et al. 2021), against measurements from publicly available detailed lens models (M DLM ) of the same clusters. We use data from the Sloan Giant Arc Survey, the Reionization Lensing Cluster Survey, the Hubble Frontier Fields, and the Cluster Lensing and Supernova Survey with Hubble. We find a scatter of 18.2% (8.2%) with a bias of -7.1% (1.0%) between M corr (<θ arcs ) (M SHM ) and M DLM . Last, we compare the statistical uncertainties measured in this work to those from simulations. This work demonstrates the successful application of these methods to observational data. As the effort to efficiently model the mass distribution of strong lensing galaxy clusters continues, we need fast, reliable methods to advance the field.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Self-Induced Curvature in an Internally Loaded Peridynamic Fiber

A straight fiber with nonlocal forces that are independent of bond strain is considered. These internal loads can either stabilize or destabilize the straight configuration. Transverse waves with long wavelength have unstable dispersion properties for certain combinations of nonlocal kernels and internal loads. When these unstable waves occur, deformation of the straight fiber into a circular arc can lower its potential energy in equilibrium. The equilibrium value of the radius of curvature is computed explicitly.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Near-infrared Spectrum of the Nuclear Star Cluster: Looking below the Tip of the Iceberg, and Comparisons with Extragalactic Nuclei

Long-slit near-infrared (NIR) spectra of the Galactic nuclear star cluster (NSC) are discussed. The spectra sample the major axis of the NSC out to its half-light radius. The absorption spectrum of the central regions of the NSC is averaged over angular scales of tens of arc seconds in order to sample globular cluster-like total luminosities, and the results are compared with model spectra. The equivalent widths of Na i2.21 μm and Ca 2.26 μm outside of the center of the NSC, where light from nuclear bulge stars contributes a large fraction to the total flux, are consistent with solar chemical mixtures. In contrast, the equivalent widths of Na i2.21 μm and Ca i2.26 μm near the center of the NSC are larger than expected from models with solar chemical mixtures, even after light from the brightest evolved stars is removed. The depths of spectroscopic features changing along the major axis of the NSC are consistent with imaging studies that have found evidence of population gradients in the NSC. That Na i2.21 μm and Ca i2.26 μm are deeper than predicted for solar chemical mixtures over a range of evolutionary states is consistent with previous studies that find that the majority of stars near the center of the NSC formed from material that had nonsolar chemical mixtures. The depths of the Na i2.21 μm and Ca i2.26 μm features in the central regions of the NSC are comparable to those in the nuclear spectrum of the early-type Virgo disk galaxy NGC 4491, and are deeper than in the central spectra of NGC 253 and 7793. A spectrum of nebular emission and the youngest stars near the galactic center is also extracted. The equivalent widths of emission features in the extracted NIR spectrum are similar to those in the nuclear spectrum of NGC 253, and it is argued that this agreement is best achieved if the current episode of star formation near the center of the NSC has been in progress for at least a few megayears.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Macroscopic trends of neoclassical tearing stability in high-field H-mode tokamak pilot plants

The neoclassical tearing mode (NTM) stability metric—minimum marginally stable island width $w$$^{*}_{m}$—was compared across 14651 inductive high-field tokamak pilot plant equilibria. Larger devices with reduced elongation and/or increased minor radius demonstrated an order-of-magnitude increase in $w$$^{*}_{m}$, primarily due to a reduction in bootstrap drive. This work is part of an ongoing effort to ensure passive NTM-stability in the ARC tokamak, in which the technology to achieve active tearing-suppression with localised electron cyclotron current drive does not yet exist. The equilibrium scenarios in the database were Monte Carlo generated and normalised to the same >400MW fusion power, minimum pressure scenario at a range of plasma currents, before tearing analysis using the modified Rutherford equation was applied for all resonant poloidal and toroidal m, n modes up to n = 4. Single-helicity toroidal Δ' calculations in resistive DCON set the minimum marginally stable island width, and a simple modal scaling proportional to –m 2 n –1 was identified for high-m Δ' values. The dominant correlates of $w$$^{*}_{m}$ and Δ' across the database were analysed using interpretable machine learning techniques.

NTM seeding↗
DOE OSTI2021

Signatures of large-scale cold fronts in the optically-selected merging cluster HSC J085024+001536

Abstract We represent a joint X-ray, weak-lensing, and optical analysis of the optically-selected merging cluster, HSC J085024+001536, from the Subaru HSC-SSP survey. Both the member galaxy density and the weak-lensing mass map show that the cluster is composed of south-east and north-west components. The two-dimensional weak-lensing analysis shows that the south-east component is the main cluster, and the sub-cluster and main cluster mass ratio is $0.32^{+0.75}_{-0.23}$. The north-west sub-cluster is offset by ∼700 kpc from the main cluster center, and their relative line-of-sight velocity is ∼1300 km s−1 from spectroscopic redshifts of member galaxies. The X-ray emission is concentrated around the main cluster, while the gas mass fraction within a sphere of 1′ radius of the sub-cluster is only $f_{\mathrm{gas}}=4.0^{+2.3}_{-3.3}\%$, indicating that the sub-cluster gas was stripped by ram pressure. An X-ray residual image shows three arc-like excess patterns, of which two are symmetrically located at ∼550 kpc from the X-ray morphological center, and the other is close to the X-ray core. The excess close to the sub-cluster has a cold-front feature where dense-cold gas and thin-hot gas contact. The two outer excesses are tangentially elongated about ∼450–650 kpc, suggesting that the cluster is merged with a non-zero impact parameter. Overall features revealed by the multi-wavelength datasets indicate that the cluster is at the second impact or later. Since the optically-defined merger catalog is unbiased for merger boost of the intracluster medium, X-ray follow-up observations will pave the way to understand merger physics at various phases.

Tanaka, Keigo↗
DOE OSTI2026

OzDES Reverberation Mapping of Active Galactic Nuclei: Final Data Release, Black-Hole Mass Results, & Scaling Relations

Over the last decade, the Australian Dark Energy (OzDES) collaboration has used Reverberation Mapping to measure the masses of high redshift supermassive black holes. Here we present the final review and analysis of this OzDES reverberation mapping campaign. These observations use 6-7 years of photometric and spectroscopic observations of 735 Active Galactic Nuclei (AGN) in the redshift range 0.13-3.85 and bolometric luminosity range 44.3 - 47.5 erg/s. Both photometry and spectra are observed in visible wavelengths, allowing for the physical scale of the AGN broad line region to be estimated from reverberations of the H{̱e̱ṯa̱}̱, MgII and CIV emission lines. We successfully use reverberation mapping to constrain the masses of 62 super-massive black holes, and combine with existing data to fit a power law to the lag-luminosity relation for the H{̱e̱ṯa̱}̱ and MgII lines with a scatter of ~0.25 dex, the tightest yet identified, fit specifically for consistency with high redshift AGN. We fit a similarly constrained relation for CIV, resolving a tension with the low luminosity literature AGN by accounting for selection effects arising from finite survey length. We also examine the impact of emission line width and luminosity (related to accretion rate) in reducing the scatter of these scaling relationships and find no significant improvement over the lag-only approach for any of the three lines. Using these relations, we further estimate the masses and accretion rates of 246 AGN with single epoch methods. We also use these relations to estimate the relative sizes of the H{̱e̱ṯa̱}̱, MgII and CIV emitting regions. In short, we provide a comprehensive benchmark of high redshift AGN reverberation mapping at the close of this most recent generation of surveys, including light curves, time-delays, and a set of significantly improved radius-luminosity relations for use with high-redshift populations.

McDougall, Hugh [Queensland U.]↗
DOE OSTI2026

Modeling the PV System Level Economic Impact of PV Connector Failure Modes

Photovoltaic (PV) connectors must maintain mechanical integrity for over 25 years while operating under UV exposure, elevated temperature, and mechanical loading. Connector degradation increases with electrical resistance, leading to energy losses, unplanned downtime, and higher operation and maintenance (O&M) costs and in severe cases, safety risks from overhearing or arcing. Connector related failures remain among the most frequent causes of disruption in utility-scale PV (UPV) systems, yet their lifetime economic impacts are poorly quantified. This work presents a techno-economic analysis (TEA) framework that links identified connector failure modes to system level energy losses and lifetime cost impacts using identified resistance measurements and failure rates from 6,2761 PV connectors inspected. Connector failures increase system level O&M costs, raising LCOE by roughly 5%. Downtime driven availability losses dominate economic impact. Resistance-driven I2R and IV-curve losses are secondary, but remain non-negligible. Thermal damage, bend-radius violations, and loose connections drive the majority of LCOE uplift Improving connector reliability through better installation quality, inspection, and design can meaningfully reduce lost energy, O&M costs, and LCOE.

14 SOLAR ENERGY↗
DOE OSTI2020

Efficient Mass Estimate at the Core of Strong Lensing Galaxy Clusters Using the Einstein Radius

In the era of large surveys, yielding thousands of galaxy clusters, efficient mass proxies at all scales are necessary in order to fully utilize clusters as cosmological probes. At the cores of strong lensing clusters, the Einstein radius can be turned into a mass estimate. This efficient method has been routinely used in literature, in lieu of detailed mass models; however, its scatter, assumed to be similar to 30%, has not yet been quantified. Here, we assess this method by testing it against ray-traced images of cluster-scale halos from the Outer RimN-body cosmological simulation. We measure a scatter of 13.9% and a positive bias of 8.8% in M (<θ E ), with no systematic correlation with total cluster mass, concentration, or lens or source redshifts. We find that increased deviation from spherical symmetry increases the scatter; conversely, where the lens produces arcs that cover a large fraction of its Einstein circle, both the scatter and the bias decrease. While spectroscopic redshifts of the lensed sources are critical for accurate magnifications and time delays, we show that for the purpose of estimating the total enclosed mass, the scatter introduced by source redshift uncertainty is negligible compared to other sources of error. Finally, we derive and apply an empirical correction that eliminates the bias, and reduces the scatter to 10.1% without introducing new correlations with mass, redshifts, or concentration. Our analysis provides the first quantitative assessment of the uncertainties in M (<θ E ), and enables its effective use as a core mass estimator of strong lensing galaxy clusters.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

COOL-LAMPS. II. Characterizing the Size and Star Formation History of a Bright Strongly Lensed Early-type Galaxy at Redshift 1.02

We present COOL J1323+0343, an early-type galaxy at z = 1.0153 ± 0.0006, strongly lensed by a cluster of galaxies at z = 0.353 ± 0.001. This object was originally imaged by DECaLS and noted as a gravitational lens by COOL-LAMPS, a collaboration initiated to find strong-lensing systems in recent public optical imaging data, and confirmed with follow-up data. With ground-based grzH imaging and optical spectroscopy from the Las Campanas Observatory and the Nordic Optical Telescope, we derive a stellar mass, metallicity, and star formation history from stellar-population synthesis modeling. The lens modeling implies a total magnification, summed over the three images in the arc, of μ ~ 113. The stellar mass in the source plane is M * ~ 10.64 M ⊙ and the 1σ upper limit on the star formation rate (SFR) in the source plane is SFR ~ 3.75 × 10 -2 M ⊙ yr -1 (log sSFR = -12.1 yr -1 ) in the youngest two age bins (0–100 Myr), closest to the epoch of observation. Our measurements place COOL J1323+0343 below the characteristic mass of the stellar mass function, making it an especially compelling target that could help clarify how intermediate-mass quiescent galaxies evolve. We reconstruct COOL J1323+0343 in the source plane and fit its light profile. This object is below the expected size evolution of an early-type galaxy at this mass with an effective radius r e ~ 0.5 kpc. This extraordinarily magnified and bright lensed early-type galaxy offers an exciting opportunity to study the morphology and star formation history of an intermediate-mass early-type galaxy in detail at z ~ 1.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

The Dark Energy Survey Bright Arcs Survey: Candidate Strongly Lensed Galaxy Systems from the Dark Energy Survey 5000 Square Degree Footprint

We report the combined results of eight searches for strong gravitational lens systems in the full 5000 square degrees of Dark Energy Survey (DES) observations. The observations accumulated by the end of the third observing season fully covered the DES footprint in five filters (grizY), with an i-band limiting magnitude (at 10σ) of 23.44. In four searches, a list of potential candidates was identified using a color and magnitude selection from the object catalogs created from the first three observing seasons. Three other searches were conducted at the locations of previously identified galaxy clusters. Cutout images of potential candidates were then visually scanned using an object viewer. An additional set of candidates came from a data-quality check of a subset of the color–coadd tiles created from the full DES six-season data set. A short list of the most promising strong-lens candidates was then numerically ranked according to whether or not we judged them to be bona fide strong gravitational lens systems. These searches discovered a diverse set of 247 strong-lens candidate systems, of which 81 are identified for the first time. We provide the coordinates, magnitudes, and photometric properties of the lens and source objects, and an estimate of the Einstein radius for 81 new systems and 166 previously reported systems. This catalog will be of use for selecting interesting systems for detailed follow up, studies of galaxy cluster and group mass profiles, as well as a training/validation set for automated strong-lens searches.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Aging heat treatment design for Haynes 282 made by wire-feed additive manufacturing using high-throughput experiments and interpretable machine learning

Wire-feed additive manufacturing (WFAM) produces superalloys with complex thermal cycles and unique microstructures, often requiring optimized heat treatments. To address this challenge, we present a hybrid approach that combines high-throughput experiments, precipitation simulation, and machine learning to design effective aging conditions for the WFAM Haynes 282 superalloy. Our results demonstrate that the γ’ radius is the critical microstructural feature for strengthening Haynes 282 during post-heat treatment compared with the matrix composition and γ’ volume fraction. New aging conditions at 770°C for 50 hours and 730°C for 200 hours were discovered based on the machine learning model and were applied to enhance yield strength, bringing it on par with the wrought counterpart. This approach has significant implications for future AM alloy production, enabling more efficient and effective heat treatment design to achieve desired properties.

CALPHAD↗
DOE OSTI2025

Final report on assessment of molten salt corrosion testing of unirradiated and ion irradiated advanced manufactured high entropy alloys

Generation IV reactors and future fusion reactor designs have led to more demanding materials performance requirements due to their increased operating temperatures, corrosive coolants, and increased radiation doses compared to the current light-water reactor fleet. Among the innovative nuclear technologies under development, molten salt reactors stand out for their potential to offer superior fuel utilization, intrinsic safety characteristics, and economic viability. Of the proposed Generation IV designs, the gas fast reactor operates at 450 to 850°C and the molten salt reactor operates at 565 to 850°C, with the molten salt reactor design needing molten salt corrosion resistant materials [1, 2]. These increased temperatures and more extreme corrosion environments necessitate higher material performance, such as creep strength, radiation-tolerant microstructures, corrosion resistance, and high-temperature tensile properties. Hastelloy-N, a nickel-based alloy with additions of molybdenum and chromium, has been successfully employed to contain molten fluoride salt at temperatures up to 705°C. However, Hastelloy-N becomes embrittled upon neutron irradiation, primarily due to the accumulation of helium produced by (n,a) transmutation reactions. Furthermore, the corrosive nature of molten fluoride and chloride salts presents a formidable challenge, as these salts can react with and dissolve alloying elements such as Cr, Mo, and Fe, leading to selective leaching, loss of protective oxide layers, and accelerated degradation. High entropy alloys (HEAs) and refractory high entropy alloys (RHEAs) have emerged as a prominent area of interest, due to their ability to achieve tailored chemical compositions for specific applications. Unlike conventional alloys, HEAs are characterized by having multiple principal elements in equimolar or near equimolar ratios, leading to an unconventional alloying strategy [3]. This alloying strategy is believed to promote unique properties, such as single-phase stabilization of chemically compatible elements, lattice distortion effects due to atomic radius differences, and proposed sluggish diffusion effects. For extreme-environment applications, RHEAs have garnered much research interest because of the possibility of creating relatively ductile materials that can operate in extremely high-temperature environments, beyond the operating temperatures where other Ni-based superalloys begin to lose strength [4-6]. Idaho National Laboratory (INL) initiated a joint international effort with the Czech Republic to explore the feasibility of manufacturing HEAs for high-temperature nuclear applications using advanced manufacturing. This effort was funded at INL by the United States Department of Energy's Office of Nuclear Energy under the Advanced Reactor Technologies and Advanced Materials and Manufacturing Technologies (AMMT) Program. The HEAs were specifically designed for the corrosive and irradiation environments experienced in gas-cooled fast reactors, molten salt reactors, and fusion power. These alloys have been manufactured by multiple processes to determine the impact of manufacturing processes on the performance of the alloys in corrosive and irradiation environments. Preliminary molten salt corrosion testing showed that equimolar MoNbTiV and MoNbTi alloys exhibit exceptional performance, with arc-melted variants demonstrating only minimal degradation after 1000 hours of exposure to molten chloride salt at 700°C. Conversely, Nb2TiVZr2 showed significant molten salt corrosion susceptibility and microstructural instability during high-temperature molten salt exposures, and was, therefore deemed unfit for molten salt reactor applications. The MoNbTiV, MoNbTi, and Nb2TiVZr2 alloys were further evaluated through ion irradiation experiments conducted at the Michigan Ion Beam Laboratory at the University of Michigan. The microstructural stability and the evolution of irradiation-induced defects were characterized to assess the irradiation resistance of each of these alloys.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Determination of jet calibration and energy resolution in proton–proton collisions at $\sqrt{s} = 8~\hbox {TeV}$ using the ATLAS detector

The jet energy scale, jet energy resolution, and their systematic uncertainties are measured for jets reconstructed with the ATLAS detector in 2012 using proton–proton data produced at a centre-of-mass energy of 8 TeV with an integrated luminosity of 20fb -1 . Jets are reconstructed from clusters of energy depositions in the ATLAS calorimeters using the anti-k t algorithm. A jet calibration scheme is applied in multiple steps, each addressing specific effects including mitigation of contributions from additional proton–proton collisions, loss of energy in dead material, calorimeter non-compensation, angular biases and other global jet effects. The final calibration step uses several in situ techniques and corrects for residual effects not captured by the initial calibration. Furthermore, these analyses measure both the jet energy scale and resolution by exploiting the transverse momentum balance in γ + jet, Z + jet, dijet, and multijet events. A statistical combination of these measurements is performed. In the central detector region, the derived calibration has a precision better than 1% for jets with transverse momentum 150 GeV < p T < 1500 GeV, and the relative energy resolution is (8.4 ± 0.6)% for p T =100 GeV and (23 ± 2)% for p T =20 GeV. The calibration scheme for jets with radius parameter R = 1.0, for which jets receive a dedicated calibration of the jet mass, is also discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Search for resonant pair production of Higgs bosons in the b b ¯ b b ¯ final state using p p collisions at s = 13 TeV with the ATLAS detector

A search for resonant Higgs boson pair production in the bb¯bb¯ final state is presented. The analysis uses 126 fb -1 -139 fb -1 of pp collision data at √s=13 TeV collected with the ATLAS detector at the Large Hadron Collider. The analysis is divided into two channels, targeting Higgs boson decays which are reconstructed as pairs of small-radius jets or as individual large-radius jets. Spin-0 and spin-2 benchmark signal models are considered, both of which correspond to resonant HH production via gluon-gluon fusion. The data are consistent with Standard Model predictions. Upper limits are set on the production cross section times branching ratio to Higgs boson pairs of a new resonance in the mass range from 251 GeV to 5 TeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗