Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ultra-fast”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Ultra-Fast 4H-SiC LGAD With Etched Termination and Field Plate

The design, fabrication, and demonstration of a novel Silicon Carbide Low Gain Avalanche Detector (4HSiC LGAD), exhibiting an ultra-fast time response and excellent time resolution, are reported. Here, the use of field plates is proposed to suppress the high electric field caused by the negative bevel-etched angle in 4H-SiC LGADs based on TCAD simulations. Experimental measurements confirm that the field plate significantly increases the breakdown voltage of the 4H-SiC LGADs. Gain and time resolution are measured by using the ultraviolet transient current technique (UV-TCT) showing that 4H-SiC LGADs possess excellent timing performance, with a time resolution better than 35 ps for the injected laser signal with single minimum ionizing particle (MIP) charges generation at room temperature. Additionally, the gain suppression effect in a 4H-SiC LGAD is observed for the first time.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Ultra-Fast Non-Volatile Resistive Switching Devices with Over 512 Distinct and Stable Levels for Memory and Neuromorphic Computing

Low-current multilevel programmability with inherent non-volatility and high stability of resistance states is required for both multi-bit memory storage and deep learning accelerators but is difficult to achieve. Here, in a resistive switching system, this work realizes >512 (>9 bits) distinct non-volatile conductance levels with stable retention for each state with current levels down to the nanoampere range, highly promising for potential integration with small processing nodes with ultra-low power consumption requirements. This is achieved by demonstrating a new thin film design concept that encompasses three key features: an ultra-thin epitaxial oxygen ionic switching layer that provides a tunable energy barrier at the bottom electrode, an overcoat amorphous layer that acts as an ion migration barrier for stable state retention, and a partial conductive filament as a localized electronic transport channel to the epitaxial switching layer. A large dynamic resistance range of up to seven orders of magnitude is achieved with reset-free transitions among intermediate states, and programmability is demonstrated with ultra-fast (20 ns) pulses. Artificial neural network (ANN) simulations, based on the experimental performance and its non-idealities, demonstrate close-to-ideal inference accuracies for various Modified National Institute of Standards and Technology (MNIST) data sets.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Real-Time Ammonia and Humidity Monitoring with Ultra-Fast Conductometric Sensors Based on Porphyrin and Phthalocyanine Complexes

Organic semiconductors like porphyrins and phthalocyanines are attracting a wide range of researchers due to their versatile electrical properties and sensing performances in conductometric sensors. In this study, we investigate two types of π-extended porphyrins, which share the same macrocyclic structure but differ in their central metal. These porphyrins are employed as sublayers in bilayer heterojunction devices, with the lutetium bisphthalocyanine complex, LuPc 2 , serving as the common top layer. Remarkably, the central metal in the porphyrin macrocycle significantly influences the solubility of the materials and, consequently, the surface topography of the resulting bilayer heterojunction devices. This structural variation translates into distinct electrical and sensing performances. The device incorporating nickel as metal centre (AM2) demonstrates superior sensitivity towards NH3, with a relative response (RR) of ca. -7% at 90 ppm, an ultra-fast response time of about 9 s, and an impressive limit of detection (LOD) of 250 ppb, whereas, the device that has zinc as metal centre in sublayer (AM3) exhibits RR value of ca. -0.9% at 90 ppm with t 90 of ca. 120 s and LOD of 2 ppm. Both devices are evaluated under randomly varying NH 3 concentration and RH value. The results shows that the AM2-based sensor allows following NH 3 in real-time, while the AM3-based sensor delivers an average concentration over time. On the other hand, the AM2-based sensor exhibits slow kinetics under RH exposure, while the AM3-based sensor precisely mirrors the pattern of random RH changes generated by the software, demonstrating its exceptional responsiveness and accuracy in tracking humidity fluctuations. In conclusion, these findings underscore the critical role of the metal centre in tuning the electrical and sensing properties of the heterojunction devices.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2026

An ultra-fast method for generating synthetic down-scattered neutron data for inertial confinement fusion implosions

In inertial confinement fusion experiments at the National Ignition Facility, asymmetries are probed by a variety of neutron diagnostics, including neutron imaging systems, real-time neutron activation diagnostics (RTNADs), and neutron spectrometers. It is often useful to generate synthetic data based on these diagnostics to validate and tune models. However, current methods of doing so using Monte Carlo particle tracing are time-consuming. In this paper, an ultra-fast method is presented for generating synthetic neutron images, RTNAD data, and spectrometry data using line integrals and 3D convolutions. While it does not contain as much physics as particle tracing codes, it is thousands of times faster and produces nearly identical data. This enables analysis techniques that depend on generating large amounts of synthetic data, which will prove very useful for the study of asymmetries going forward.

Deuterium↗
DOE OSTI2025

Ultra-fast single-crystal CVD diamonds in the particle time-of-flight (PTOF) detector for low yield burn-history measurements on the NIF (invited)

The Particle Time of Flight (PTOF) diagnostic is a chemical vapor deposition diamond-based detector and is the only diagnostic for measuring nuclear bang times of low yield (<1013) shots on the National Ignition Facility. Recently, a comprehensive study of detector impulse responses revealed certain detectors with very fast and consistent impulse responses with a rise time of <50 ps, enabling low yield burn history measurements. At the current standoff of 50 cm, this measurement is possible with fast 14 MeV neutrons from deuterium–tritium (DT) fusion plasmas. PTOF-inferred DT burn width numbers compare well with widths inferred from the gamma reaction history diagnostic on mid-yield (1013–1015) shots, where both systems are capable of making this measurement. These new capabilities could be extended to 2.5 MeV deuterium–deuterium neutrons from D plasmas and to even lower yield by reducing the detector standoff distance to 10 cm; a design for this is also presented.

42 ENGINEERING↗
DOE OSTI2025

Detection of trace contaminants released from rapidly heated pulsed power electrodes by laser diagnostics

Development of a capability to measure trace gas contaminants released from pulsed power electrodes would immediately impact Sandia pulsed power research. These releases occur during ultra-fast heating of metal electrodes during pulsed power discharges and can lead to substantial power losses through plasma formation. Detection of contaminants is a formidable challenge due to the need for in-situ spatially and temporally resolved measurements of trace gases in the extreme environment of ultra-fast heated metal surfaces. We investigate the feasibility of laser diagnostics for detecting contaminants, including H-atom, OH, and H 2 O. Laser-induced fluorescence and photofragmentation fluorescence showed significant plasma emission interferences and did not yield any detectable H-atom, OH, or H 2 O. Our newly developed H-atom detection using femtosecond degenerate four-wave mixing suppressed interferences and enabled detection of H-atoms. A few shots showed large signals in the near-surface region of metal foils, suggesting the formation of a wave of H-atoms from the metal.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

PSEC5 Physical Verification

Ultra-Fast timing detectors, having a time resolution of 10pSec or less, are becoming increasingly important for many scientific disciplines, including High Energy Physics, Nuclear Physics, Medical Imaging and more. When developing ultra-fast detectors such as MCPs, LAPPDs, LGADs, SNSPDs, it is necessary to have access to a readout system that is low power, can support many channels and is cost effective. The PSEC5 chip was an application specific integrated circuit (ASIC) developed by the pioneering group of Prof. Henry Frisch at University of Chicago and micro electronic engineers at Fermi National Accelerator Laboratory. Three boards were designed, two to implement the readout system for an LAPPD and one to only characterize the PSEC1 chip. The main goal of the project shifted to setting up a testing environment to focus on the characterization of the chip. My student and I tested and characterized this ASIC using the third chip-on-board printed circuit board. Results show the successful fabrication and operation of some of the key building blocks and lead to the suggestions on modification for the second iteration of the chip.

Rico Aniles, H. D. [Unlisted]↗
DOE OSTI2025

Multi-energy ion irradiation effects and distinctive features of color center generation in yttria-stabilized zirconia driven by structural discrepancy

Regarding a requirement for inert matrix fuel (IMF) to burn minor actinides and plutonium and high-level waste immobilization, Yttria-stabilized zirconia (ZrO 2 -6.5 wt% Y 2 O 3 ) (YSZ) crystals with cubic phase are selected to comprehensively evaluate the irradiation resistance by irradiation-induced structural discrepancies across multiple energy conditions. Electronic excitation and nuclear collisions reveal distinct color centers, influenced by varying component ratios that reflect their formation mechanisms. Key factors driving ultra-fast structural transitions include collision cascades, pressure waves, and energy dissipation from electronic excitation. In this work, we find that in the electronic energy loss (E ele )-dominant region, internal latent tracks with unique surface nanostructures emerge, distinct from the defect clusters seen in the nuclear energy loss (E nuc )-dominant region, while the threshold for latent track formation and melting are identified. In conclusion, structural discrepancies driven by different energy-loss mechanisms promote the generation of singly ionized and nearest-neighbor doubly ionized oxygen vacancies, which respectively dominate the formation of F⁺ and T-centers, resulting in bandgap narrowing (4.80 eV → 4.73 eV), and furthermore triggering visible light emission (2.17 eV → 2.20 eV) in irradiated YSZ crystals, thus, enabling the design of novel irradiation-tailored material functionalities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stable laser-acceleration of high-flux proton beams with plasma collimation

Laser-plasma acceleration of protons offers a compact, ultra-fast alternative to conventional ac- celeration techniques, and is being widely pursued for potential applications in medicine, industry and fundamental science. Creating a stable, collimated beam of protons at high repetition rates presents a key challenge. Here, we demonstrate the generation of multi-MeV proton beams from a fast-replenishing ambient-temperature liquid sheet. The beam has an unprecedentedly low diver- gence of 1◦ (≤ 20 mrad), resulting from magnetic self-guiding of the proton beam during propagation through a low density vapour. The proton beams, generated at a repetition rate of 5 Hz using only 190 mJ of laser energy, exhibit a hundred-fold increase in flux compared to beams from a solid target. Coupled with the high shot-to-shot stability of this source, this represents a crucial step towards applications.

Glenn, G. D. [SLAC National Accelerator Laboratory↗
DOE OSTI2026

Probing the atomic dynamics of ultrafast melting with femtosecond electron diffraction

Melting is an every-day phase transition that is determined by thermodynamic parameters like temperature and pressure. In contrast, ultra-fast melting is governed by the microscopic response to a rapid energy input and, thus, can reveal the strength and dynamics of atomic bonds as well as the energy flow rate to the lattice. Accurately describing these processes remains challenging and requires detailed insights into transient states encountered. Here, we present data from femtosecond electron diffraction measurements that capture the structural evolution of copper during the ultrafast solid-to-liquid phase transformations. At absorbed energy densities 2-4 times the melting threshold, melting begins at the surface slightly below the nominal melting point followed by rapid homogeneous melting throughout the volume. Molecular dynamics simulations reproduce these observations and reveal a weak electron-lattice energy transfer rate for the given experimental conditions. Both simulations and experiments show no indications of rapid lattice collapse when its temperature surpasses proposed limits of superheating, providing evidence that the inherent dynamics limits the speed of disordering in ultrafast melting of metals.

FOS: Physical sciences↗
DOE OSTI2025

Pulsed laser deposition assisted epitaxial growth of cesium telluride photocathodes for high brightness electron sources

The development of high-brightness electron sources is critical to state-of-the-art electron accelerator applications like X-ray free electron laser (XFEL) and ultra-fast electron microscopy. Cesium telluride is chosen as the electron source material for multiple cutting-edge XFEL facilities worldwide. This manuscript presents the first demonstration of the growth of highly crystalized and epitaxial cesium telluride thin films on 4H-SiC and graphene/4H-SiC substrates with ultrasmooth film surfaces. The ordering of the film was characterized by in situ reflection high energy electron diffraction and multiple X-ray diagnostics. The results of the quantum efficiency performance for epitaxial cesium telluride photocathodes are also reported.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Fe-single atom catalysts facilitate fast electron transfer with MoS 2 /SnS 2 cathodes in lithium–sulfur batteries

Lithium–sulfur batteries (LSBs) emerge as promising next-generation energy storage systems offering cost-effectiveness, environmental friendliness, and high theoretical energy density. The practical implementation of LSBs faces significant hindrances due to the shuttle effect and sluggish redox reactions. To address these challenges, single-atom catalyst (SAC) based combination materials from d-block elements can offer increased active catalytic sites, rapid charge transfer, accelerated electron migration, and fast sulfur redox conversion kinetics of lithium polysulfides (LiPSs). In this study, we fabricated three different LSB cathodes: pure S, S@MoS 2 /SnS 2 , and S@Fe–MoS 2 /SnS 2 . These cathodes were then used to explore the cycle life, capacity, rate capability, and redox kinetic reactions of LiPSs while assessing the influence of Fe-SACs on their performance. As a result, LSBs with S@Fe–MoS 2 /SnS 2 cathodes demonstrate an extended cycle life of 1000 cycles at a C-rate of 0.2C, maintaining a capacity close to 500 mA h g −1 , the highest initial discharge capacity of 1622 mA h g −1 and 1066 mA h g −1 at 0.05C and 0.2C, and excellent rate capabilities of 708 mA h g −1 and 558 mA h g −1 at 1C and 2C, respectively. The synergistic effect of the Fe-SAC-based combination cathode (S@Fe–MoS 2 /SnS 2 ) creates plentiful adsorptive and highly active catalytic sites, resulting in substantially enhanced capacity for adsorbing soluble long-chain LiPSs. This facilitates ultra-fast redox kinetics, surpassing the performance of the S@MoS 2 /SnS 2 and pure S cathodes. In the ex situ analysis, results from powder X-ray diffraction (XRD) to observe the new phase, soft X-ray absorption spectroscopy (XAS) to investigate the electronic structure, and hard X-ray photoelectron microscopy (HAXPES) with different energies (900 eV, 2000 eV, and 6000 eV) to track the chemical-state evolution of Fe-SACs in MoS 2 /SnS 2 cathodes displayed notable electrochemical reversibility involving S 8 ⇄ LiPSs ⇄ Li 2 S conversion even after 1000 cycles. Additionally, in situ, operando Raman analysis can unveil a novel catalytic mechanism of Fe-SACs in MoS 2 /SnS 2 “facilitating rapid electron transfer” during the discharge and charge processes of LSBs involving the conversion of S 8 ⇄ long-chain LiPSs ⇄ Li 2 S 2 /Li 2 S. This study elucidates the working mechanism of Fe-SAC cathodes, offering insights into overcoming the shuttle effect and facilitating sulfur redox kinetics to advance commercial LSBs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

When more data hurts: Optimizing data coverage while mitigating diversity-induced underfitting in an ultrafast machine-learned potential

Machine-learned interatomic potentials (MLIPs) are becoming an essential tool in materials modeling. However, optimizing the generation of training data used to parametrize the MLIPs remains a significant challenge. This is because MLIPs can fail when encountering local environments too different from those present in the training data. The difficulty of determining a priori the environments that will be encountered during molecular dynamics simulation necessitates diverse, high-quality training data. Here, this study investigates how training data diversity affects the performance of MLIPs using the Ultra-Fast force field (UF 3 ) to model amorphous silicon nitride. We employ expert and autonomously generated data to create the training data and fit four force field variants to subsets of the data. Our findings reveal a critical balance in training data diversity: insufficient diversity hinders generalization, while excessive diversity can exceed the MLIP's learning capacity, reducing simulation accuracy. Specifically, we found that the UF 3 variant trained on a subset of the training data, in which nitrogen-rich structures were removed, offered vastly better prediction and simulation accuracy than any other variant. By comparing these UF 3 variants, we highlight the nuanced requirements for creating accurate MLIPs, emphasizing the importance of application-specific training data to achieve optimal performance in modeling complex material behaviors.

ab initio molecular dynamics↗
DOE OSTI2025

Cybersecurity Challenges in Low-Inertia Power-Electronics-Dominated Grids

Here, the low inertia characteristics of the power electronics dominated grid (PEDG) introduces challenges while restoring voltage and frequency to their nominal values. These stability challenges create new cybersecurity vulnerabilities that are not thoroughly discussed in the literature. Cyber events such as false data injection (FDI), denial of service (DoS), man-in-the-middle attacks, stealthy attacks, and advanced persistent threats target PEDG to disrupt grid stability or gain financial benefits. The low inertia of PEDG (< 2s) compared to traditional grids (~10s) exacerbates these vulnerabilities. In response to stealthy attacks on state variables that supervisory layers cannot detect until significant harm occurs, the low inertia characteristics of PEDG offer substantial stealthy attack surfaces. To counteract such threats, PEDG must be equipped with ultra-fast real-time anomaly detection system and trajectory prediction mechanism to achieve effective cyberattack resiliency.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Advancing Reel-to-Reel Inspection Techniques for Long HTS Conductors: Comparison and Innovations

The continuous advancement of high-temperature superconductor (HTS) technologies has greatly accelerated the development and deployment of HTS applications. Among the critical tools supporting these advancements are reel-to-reel (R2R) critical current (I c ) measurement techniques, which are extensively used by both manufacturers and end users to characterize long-length REBCO conductors. These techniques play a vital role in quality assurance and quality control (QA/QC), ensuring the reliability and performance of HTS conductors and applications throughout the production cycle. We have developed a range of in-house devices for R2R measurements at the University of Houston and Princeton Plasma Physics Laboratory. These include one-dimensional (1D) scan using a magnetic circuit (MC) and two-dimensional (2D) magnetic field mapping systems based on scanning probe array microscope (SPAM) or scanning probe microscopy (SPM). Each technique offers distinct advantages: the MC system provides ultra-fast scanning speeds, ideal for rapid inspection in large-scale industrial production; the high-resolution SPM delivers detailed insights for conductor research and development; and the SPAM, with its simpler mechanical setup, can be upgraded for higher field and lower temperature conditions with a balanced 2D resolution. Here we compared the magnetization and detection capabilities of these techniques through experiments on rare-earth barium copper oxide (REBCO) coated conductor samples, with data analysis supported by numerical simulations. Based on our comprehensive comparative studies, we propose enhancements for each measurement system and provide guidelines for selecting the optimal technique combinations to meet specific application requirements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Physical Testing of The PSEC5 ASIC

The PSEC5 ASIC is a high-speed waveform sampling chip designed for ultra-fast timing detectors, offering up to 40 GSPS sampling with 10-bit resolution. This makes it well-suited for applications requiring fine time resolution, such as MCPs and LGADs. This work focuses on the physical testing and validation of the chip s internal clocking and SPI-controlled registers. Testing began with inspection of schematics and the prototype to identify and resolve design issues. Then, custom firmware was developed for an Arduino controller to interface with the chip via SPI, enabling read and write access to key control registers. Results confirm that the VCO operates between ~3.2 4.0 GHz and remains stable under non-VCOVDD fluctuations. The Division Ratio register enables frequency division by known factors (256, 128, 64, etc.), indicating a pre-division frequency of 3.2 GHz when the digital band is unmodified. While most registers responded correctly, some issues were observed, including unexpected current draw and unstable discriminator behavior. Overall, the chip shows promising functionality, but further work is needed to understand the state of the read only registers and address the existing issues. Continued testing and firmware development will be critical to ensuring reliable integration into detector systems.

Fahey, Alexander [Unlisted, US]↗