Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid phase alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Structural uniformity and compositional homogeneity of solid-phase alloyed rod

Solid-phase processes have emerged as an alternative to fusion-based alloying to avoid coarse microstructures, undesirable phase formation, and high energy consumption. However, achieving uniform distribution of alloying elements during friction-based processing remains challenging due to highly heterogeneous thermomechanical conditions. This work evaluates the structural uniformity and compositional homogeneity of Al–Cu–Zn alloyed rods produced by friction extrusion (FE) and establishes the role of the rotational speed to feed rate ratio (N/V) on alloying effectiveness. A systematic matrix of FE experiments was conducted at constant extrusion ratio with N/V values ranging from 3.7 to 300. Compositional uniformity was assessed along the rod length (ICP-OES), in three dimensions (X-ray computed tomography), and at the microscale (SEM–EDS), supported by a gray-level co-occurrence matrix (GLCM)–based homogeneity metric. Smoothed particle hydrodynamics (SPH) simulations were used to reveal material flow and thermomechanical fields. Results show that N/V = 100 produces a high-shear mixing zone that eliminates the unmixed core and enables near-full dissolution and dispersion of Cu and Zn. At lower N/V, a laminar flow region persists at the rod center, causing segregation and large composition gradients. The combined experimental–computational analysis provides mechanistic insight into the transition from fragmented particle dispersion to thermomechanically assisted metallurgical mixing. This study establishes processing–structure relationships for solid-phase alloying and provides guidance for achieving homogenized compositions comparable to wrought alloys via rapid, scalable FE processing.

Aluminum↗
DOE OSTI2024

Upcycled high-strength aluminum alloys from scrap through solid-phase alloying

Although recycling secondary aluminum can lead to energy consumption reduction compared to primary aluminum manufacturing, products produced by traditional melt-based recycling processes are inherently limited in terms of alloy composition and microstructure, and thus final properties. To overcome the constraints associated with melting, we have developed a solid-phase recycling and simultaneous alloying method. This innovative process enables the alloying of 6063 aluminum scrap with copper, zinc, and magnesium to form a nanocluster-strengthened high-performance aluminum alloy with a composition and properties akin to 7075 aluminum alloy. The unique nanostructure with a high density of Guinier-Preston zones and uniformly precipitated nanoscale η‘/Mg(CuZn) 2 strengthening phases enhances both yield and ultimate tensile strength by >200%. By delivering high-performance products from scrap that are not just recycled but upcycled , this scalable manufacturing approach provides a model for metal reuse, with the option for on-demand upcycling of a variety of metallic materials from scrap sources.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid Phase Gradient Alloying Method via ShAPE

Alloying has been used to confer desirable properties to various metallic systems since the bronze age. For example, Ni, Mn, and Cr are alloyed into an Fe matrix to make steel, which has improved strength and corrosion resistance (as displayed in Fig. 1). In addition to the type of alloying elements, the amount of alloying elements added into a matrix is also very critical for a material’s mechanical property, physical property, machinability, and cost. Conventionally, new alloys are discovered by combining alloy precursors and elemental constituents into a mixture and melting them together. The solidified product or ingot represents a usually non-homogeneous combination of the chemistry with a microstructure dictated by the physics of solidification. It is time and energy intensive to optimize the alloying amounts via the casting process and hence, economically not conducive to rapid alloy discovery. In addition, the cast microstructure seen in the as-cast ingot is often not the ideal, nor even desired structure for optimized performance. Cast materials often need further processing such as homogenization, annealing, and deformation work put in through rolling, forging, extruding, etc. to have favorable microstructures and properties. A faster method to discover new alloy combinations and evaluate them in their worked or processed form is needed. Recently, Laser Engineered Net Shaping was applied to fabricate gradient compositional material for alloy designing. However, the mechanical properties of this gradient alloy were poor due to the existence of impurities, oxidation and cracks that are inherent in the melt-solidification process. Because of these limitations, we propose to use a solid-phase process (ShAPE) to create bulk materials (extrudates) that vary in composition from one end of the extruded solid to the other. Various manufacturing methods for alloy design including conventional casting method, laser based combinatorial method and current solid phase gradient alloying method are displayed and compared in Fig. 2. ShAPE machine and a schematic of ShAPE process are displayed in Fig. 3. Starting material is processed by a rotating and plunging die to form an extrudate. We are proposing through this methodology to invent a new, bulk-scale combinatorial technique. With this novel technique, alloying element can be dissolved into the matrix with a continued gradient without bulk melting. Formation of inter-metallics and defects originating from melt processing can be avoided. In addition, the ShAPE process creates the mixed alloy chemistry, and meanwhile subjects the material to severe plastic strain, which induces the favorable “worked” microstructure. Products from the ShAPE process can be tested in hardness directly providing a path to rapid evaluation of mechanical properties. The ability to create graded structures using friction stir processing (FSP) has been demonstrated, however using the ShAPE process we believe will lead to much faster and higher fidelity results. When combined with high throughput screening methods of physical, mechanical and microstructural property characterization, efficiency and accuracy of alloy design can be significantly improved.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Graph neural networks predict energetic and mechanical properties for models of solid solution metal alloy phases

Here, we developed a PyTorch-based architecture called HydraGNN that implements graph convolutional neural networks (GCNNs) to predict the formation energy and the bulk modulus for models of solid solution alloys for various atomic crystal structures and relaxed volumes. We trained the GCNN surrogate model on a dataset for nickel–niobium (NiNb) generated by the embedded atom model (EAM) empirical interatomic potential for demonstration purposes. The dataset was generated by calculating the formation energy and the bulk modulus as a prototypical elastic property for optimized geometries starting from initial body-centered cubic (BCC), face-centered cubic (FCC), and hexagonal compact packed (HCP) crystal structures, with configurations spanning the possible compositional range for each of the three types of initial crystal structures. Numerical results show that the GCNN model effectively predicts both the formation energy and the bulk modulus as function of the optimized crystal structure, relaxed volume, and configurational entropy of the model structures for solid solution alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Manufacturing Dissolvable Alloy Components using ShAPE: A Study on Solid Phase Processing of Mg-W Composites and WJ11 Alloys

Dissolvable alloys and composites are an emerging class of materials that demonstrate tailored sorptivity in corrosive environments. This work explored the viability of solid phase processing (SPP) techniques, namely the shear assisted processing and extrusion (ShAPETM) method, to manufacture dissolvable magnesium composites and alloys components such as rods and tubes. The study also determined the effects of material composition and manufacturing process conditions on material microstructures developed during SPP and the resulting performance of the components. Explicit properties of interest included ultimate tensile strength, ultimate compressive strength, and yield strength. The application fields of interest for dissolvable alloys were identified as oil-and-gas operations and biomedical implants. Accordingly, PNNL collaborated with industrial and academia partners, Fortek Industries, Houston and University of Pittsburgh, during the course of this project for material and ShAPE process development. PNNL determined the viability of the using ShAPE to process the custom-designed materials provided by the project partners. This was done by identifying process parameters such as tool rotation rate, tool plunge rate, and process cooling optimal for manufacturing components with consolidated microstructures. Subsequently, PNNL also performed microstructural characterization on unprocessed and processed samples and mechanical property testing. One of the major findings from this work is that ShAPE was able to manufacture dissolvable magnesium composite and alloy rods and tubes with consolidated homogeneous microstructures and minimal macroscale defects on component surfaces. It was observed that samples processed via ShAPE demonstrated an average grain size < 2 - 5 µm, which was markedly lower than that of the precursors with 8 – 13 µm grains. Results showed that the ShAPE synthesized dissolvable magnesium composite and alloy strength was on par with or better than those components that were manufactured using traditional manufacturing processes such as forging and extrusion. It is noteworthy that the ShAPE samples were made with considerably lower number of process steps.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compositionally graded aluminum-silicon alloy fabricated via friction extrusion

Herein, a novel solid-phase gradient alloying technique was developed for a high throughput composition-microstructure-mechanical property assessment. Friction extrusion of a two-piece billet setup facilitated the formation of a seamless compositionally graded aluminum (Al)-silicon (Si) extrudate rod, with Si concentration in Al matrix gradually increasing from ~1 at% at one end to ~7 at% at the other end of the rod. We observed a strong dependence of the Al grain size, morphology, and texture on the Si concentration. The Si particles pinned the recrystallized grain boundaries resulting in refined (< 10 µm) and textured grains in the high Si content region, while the Al grains in the low Si region are equiaxed, randomly textured, and with a larger average size (~50 µm). The hardness of Al-Si gradient extrudate increases by ~50% percent with a 6 at% increase in Si content due to Hall Petch and particle strengthening effects. Our approach demonstrates the use of a solid phase processing technique to successfully produce a defect-free continuously compositionally graded bulk components thus overcoming the limitations of porosity and material heterogeneities commonly observed in other techniques such as by additive laser deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An Assessment of the Safeguards Implications of Particle and Alloy Formation in MSRs

Molten salt reactors (MSRs) present unique challenges for applying safeguards measures and differ significantly from traditional nuclear reactors. Although the special fissionable materials within MSRs principally exist as dissolved species within the fuel salt, key actinides of interest may also be converted to solid phases including alloys and precipitated oxides via chemical and electrochemical reactions. These solid-phase components will complicate the nuclear material accounting and control (NMAC) approaches that have, so far, primarily targeted measurements of the liquid salt itself. For example, most of the proposed monitoring and characterization methods for MSRs are reliant on homogeneity of the salt and the ability to maintain accountable materials in solution. Solid deposits and particulates could invalidate the assumption of homogeneity and necessitate the use of new models and measurement tools to permit a full accounting of all nuclear material in an MSR. To address this, the likelihood of solids formation in MSRs, estimated the rate at which these solids could form, and assessed the monitoring tools that are available to account for the presence of these materials were examined. Specifically, three solid forming mechanisms were investigated, including (1) the accumulation of actinides within the MSR’s structural materials due to alloying, (2) the accumulation of actinides within noble metal fission product particulates, and (3) the generation of actinide oxides from interactions with salt impurities. These modeling-informed studies were completed with considerations to both fluoride- and chloride-containing salts. It was determined that, although measurable amounts of special fissionable material were expected to alloy with the structural elements and fission products, the predicted amounts were below levels considered as significant quantities (SQ) by the International Atomic Energy Agency (IAEA). However, it was determined that sufficiently large oxygen concentrations could potentially lead to significant quantities of special fissionable material being converted to solid oxide phases. As such, a comparative study of technologies that are commercially available to assist in monitoring and accountancy of this material was presented. Policy implications, design recommendations, and suggestions for follow-on experimental work were also presented to further assist reactor vendors in designing and controlling the fuel salt chemistry to address potential safeguards considerations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2017

The Evolution of the Deformation Substructure in a Ni-Co-Cr Equiatomic Solid Solution Alloy

The equiatomic NiCoCr alloy exhibits an excellent combination of strength and ductility, even greater than the FeNiCrCoMn high entropy alloy, and also displays a simultaneous increase in strength and ductility with decreasing the testing temperature. To systemically investigate the origin of the exceptional properties of NiCoCr alloy, which are related to the evolution of the deformation substructure with strain, interrupted tensile testing was conducted on the equiatomic NiCoCr single-phase solid solution alloy at both cryogenic and room temperatures at five different plastic strain levels of 1.5%, 6.5%, 29%, 50% and 70%. The evolution of deformation substructure was examined using electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), conventional transmission electron microscopy (CTEM), diffraction contrast imaging using STEM (DCI-STEM) and atomic resolution scanning transmission electron microscopy. While the deformation substructure mainly consisted of planar dislocation slip and the dissociation of dislocations into stacking faults at small strain levels (≤6.5%), at larger strain levels, additional substructures including nanotwins and a new phase with hexagonal close packed (HCP) lamellae also appeared. The volume fraction of the HCP lamellae increases with increasing deformation, especially at cryogenic temperature. First principles calculations at 0 K indicate that the HCP phase is indeed energetically favorable relative to FCC for this composition. The effects of the nanotwin and HCP lamellar structures on hardening rate and ductility at both cryogenic and room temperature are qualitatively discussed.

Twinning↗
DOE OSTI2021

Development of Precipitation-Strengthened Al 0.8 NbTiVM (M = Co, Ni) Light-Weight Refractory High-Entropy Alloys

Single-phase solid-solution refractory high-entropy alloys (RHEAs) have been receiving significant attention due to their excellent mechanical properties and phase stability at elevated temperatures. Recently, many studies have been reported regarding the precipitation-enhanced alloy design strategy to further improve the mechanical properties of RHEAs at elevated temperatures. In this study, we attempted to develop precipitation-hardened light-weight RHEAs via addition of Ni or Co into Al 0.8 NbTiV HEA. The added elements were selected due to their smaller atomic radius and larger mixing enthalpy, which is known to stimulate the formation of precipitates. The addition of the Ni or Co leads to the formation of the sigma precipitates with homogeneous distribution. The formation and homogeneous distribution of sigma particles plays a critical role in improvement of yield strength. Furthermore, the Al 0.8 NbTiVM 0.2 (M = Co, Ni) HEAs show excellent specific yield strength compared to single-phase AlNbTiV and NbTiVZr RHEA alloys and conventional Ni-based superalloy (Inconel 718) at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid-state phase transitions of two quaternary metallic fuel alloys (U-2.5Mo-2.5Ti-5.0Zr and U-1.5Mo-1.5Ti-7.0Zr in wt. %)

This study focuses on the solid-state phase transitions of two quaternary fuel alloys for fast reactors: U-1.5Mo-1.5Ti-7.0Zr (U-MT7Z) and U-2.5Mo-2.5Ti-5.0Zr (U-MT5Z). Here, the phase transitions were determined by differential scanning calorimetry (DSC), X-ray powder diffraction (XRD), and scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS). To identify the high temperature phases, the alloys were annealed at 873K, 948K, 1023K, and 1123K (all under 72 hours). Combining those characterizations, the phase transitions are determined. In U-MT7Z, there is one phase transition observed, and it is ascribed to α + U 2 Ti → γ transition. In U-MT5Z, two transitions are found. The first transition is α → γ, while the second is U 2 Ti → γ. The γ phase onset temperature of U-MT5Z is lower than that of U-MT7Z due to the higher Mo content.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Superior zero thermal expansion dual-phase alloy via boron-migration mediated solid-state reaction

Rapid progress in modern technologies demands zero thermal expansion (ZTE) materials with multi-property profiles to withstand harsh service conditions. Thus far, the majority of documented ZTE materials have shortcomings in different aspects that limit their practical utilization. Here, we report on a superior isotropic ZTE alloy with collective properties regarding wide operating temperature windows, high strength-stiffness, and cyclic thermal stability. A boron-migration-mediated solid-state reaction (BMSR) constructs a salient “plum pudding” structure in a dual-phase Er-Fe-B alloy, where the precursor ErFe 10 phase reacts with the migrated boron and transforms into the target Er 2 Fe 14 B (pudding) and α-Fe phases (plum). The formation of such microstructure helps to eliminate apparent crystallographic texture, tailor and form isotropic ZTE, and simultaneously enhance the strength and toughness of the alloy. These findings suggest a promising design paradigm for comprehensive performance ZTE alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrochemical materials including solid and liquid phases

Electrochemical devices, and associated materials and methods, are generally described. In some embodiments, an electrochemical device comprises an electroactive material. The electroactive material may comprise an alloy having a solid phase and a liquid phase that co-exist with each other. As a result, such a composite electrode may have, in some cases, the mechanical softness to permit both high energy densities and an improved current density as compared to, for example, a substantially pure metal electrode.

Chiang, Yet-Ming↗
DOE OSTI2025

Phase-field model of alloy solidification far from chemical equilibrium at the solid-liquid interface

We further develop a recently introduced phase-field model of far-from-equilibrium alloy solidification under additive manufacturing conditions [K. Ji et al., Phys. Rev. Lett. 130, 026203 (2023)]. This model utilizes enhanced solute diffusivity within the spatially diffuse interface region to quantitatively capture solute trapping with a larger interface width, thereby making simulations on experimentally relevant length and timescales computationally feasible. The main developments presented here include testing the robustness of different variational formulations, extending the model to concentrated alloys by incorporating solid and liquid free energies from thermodynamic databases, as illustrated for hypoeutectic Al-Ag alloys with CALPHAD, extending convergence tests as a function of interface width to 3D, and carrying out simulations in both 2D and 3D to examine existing theories of microstructure development. Our results indicate that the simplest variational formulation that interpolates the bulk free-energy density between its solid and liquid forms is the most robust. Remarkably, for hypoeutectic Al-Ag alloys, this formulation yields a high-velocity nonequilibrium phase diagram that is independent of interface width, thereby demonstrating that the framework of enhanced solute diffusivity can be nontrivially extended to concentrated alloys. Other variational formulations have restricted ranges of materials or processing parameters that can be reliably modeled. We use 2D simulations to construct high-velocity microstructure selection maps for dilute Al-Cu alloys. The results validate the important role of latent heat rejection at the interface and extend the limited predictions of linear stability analysis [A. Karma and A. Sarkissian, Phys. Rev. E 47, 513 (1993)] and sharp-interface 1D simulations to fully nonlinear regimes. Furthermore, 3D simulations, carried out using a computationally tractable axisymmetric cellular/dendritic interface shape, demonstrate a good convergence similar to that observed in 2D as a function of interface width. Full 3D simulations, in turn, reveal that the standard theory of absolute stability is a good predictor of the upper critical velocity beyond which steady-state growth becomes unstable, despite the different morphological manifestations of this instability in 2D and 3D.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A comparative study of solute trapping in Fe-(33–45 at%) Cu alloys manufactured by laser directed energy deposition

The high cooling rates in laser directed energy deposition (DED-LB) of alloys lead to substantial amounts of solute trapping as solute atoms cannot diffuse away from the solid/liquid interface before it advances. In some concentrated alloys, this results in supersaturated solid phases that form nanoscale hierarchical microstructures when the solute atoms precipitate out during reheating from subsequent laser passes. We choose the Iron-Copper (Fe-Cu) binary alloy as model system as it is chemically homogeneous in the liquid phase and has negligible solid solubility at room temperature. Two alloys with nominal compositions in atomic (at.) %, Fe67Cu33 and Fe55Cu45, were manufactured using DED-LB. Scanning transmission electron microscopy (STEM), energy dispersive spectroscopy (EDS) and wavelength dispersive spectroscopy (WDS) were used to characterize the nanostructures and heterogeneous chemical compositions. A non-equilibrium solute partitioning model was used to compute the supersaturated chemistries of the constituent phases and validated with experimentally measured compositions. The measured phase compositions of the two alloys were very similar, at roughly 12 at.% Cu and 4 at.% Fe in the α(bcc)-Fe and ε(fcc)-Cu phases respectively, despite having different processing parameters and mechanical behavior. This indicates that the total thermal history, that depends on both the processing parameters and laser scan pattern, plays a stronger role on the final microstructure evolution than just the initial quantity of trapped solute. In addition, we find that current non-equilibrium solute partitioning models applied on the continuum scale fall short of predicting accurate quantitative phase compositions in concentrated alloys, although the qualitative trends are captured correctly.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A map of single-phase high-entropy alloys

High-entropy alloys have exhibited unusual materials properties. The stability of equimolar single-phase solid solution of five or more elements is supposedly rare and identifying the existence of such alloys has been challenging because of the vast chemical space of possible combinations. Herein, based on high-throughput density-functional theory calculations, we construct a chemical map of single-phase equimolar high-entropy alloys by investigating over 658,000 equimolar quinary alloys through a binary regular solid-solution model. We identify 30,201 potential single-phase equimolar alloys (5% of the possible combinations) forming mainly in body-centered cubic structures. We unveil the chemistries that are likely to form high-entropy alloys, and identify the complex interplay among mixing enthalpy, intermetallics formation, and melting point that drives the formation of these solid solutions. We demonstrate the power of our method by predicting the existence of two new high-entropy alloys, i.e. the body-centered cubic AlCoMnNiV and the face-centered cubic CoFeMnNiZn, which are successfully synthesized.

36 MATERIALS SCIENCE↗
NASA NTRS1971

The effect of solute additions on the steady-state creep behavior of dispersion-strengthened aluminum.

The effect of solute additions on the steady-state creep behavior of coarse-grained dispersion-strengthened aluminum alloys was studied. Recrystallized dispersion-strengthened solid solutions were found to have stress and temperature sensitivities quite unlike those observed in single-phase solid solutions having the same composition and grain size. The addition of magnesium or copper to the matrix of a recrystallized dispersion-strengthened aluminum causes a decrease in the steady-state creep rate which is much smaller than that caused by similar amounts of solute in single-phase solid solutions. All alloys exhibited essentially a 4.0 power stress exponent in agreement with the model of Ansell and Weertman. The activation energy for steady-state creep in dispersion-strengthened Al-Mg alloys, as well as the stress dependence, was in agreement with the physical model of dislocation climb over the dispersed particles.

Reynolds, G. H.↗