Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RECOVERY DEVICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

A device for volatile organic compound (VOC) analysis from skin using heated dynamic headspace sampling

Abstract Human skin is an important source of volatile organic compounds (VOCs) offering noninvasive methods to gain clinical metabolite information. This work was focused on the development of a skin sampling device based on a dynamic headspace sampling method with the addition of temperature to increase VOC metabolite recovery. The device preconcentrates skin VOC emissions onto a sorbent substrate, which can either be preserved for offline analysis or attached to a real time sensor downstream. In this work, skin VOC samples were analyzed offline using thermal desorption-gas chromatography-mass spectrometry. A list of 10 common skin VOCs was pre-selected to optimize parameters of sampling time, sampling temperature, and sorbent selection. Overall, this study highlights an effective skin VOC sampling technology with a heating dimension (40 °C, rather than 30 °C or no heating) with a sampling time of 15 min (rather than 5 or 30 mins) and onto Tenax TA sorbent (rather than PDMS), which collectively increases the recovery of compounds with lower vapor pressure and decreases the observed variability in skin VOC measurements. Finally, a list of 79 skin VOC compounds were detected and identified within a cohort of 20 young, healthy volunteers.

Biochemistry & Molecular Biology↗
DOE OSTI2026

Simulating Thermoelectric Devices Using the MOOSE Framework

Thermoelectric generators (TEG) are devices that generate energy by converting heat into electricity or provide cooling via the Peltier effect. This feature of thermoelectric devices originates from the Seebeck, Peltier, Thomson, and Joule heating effects. TEGs can be applied in energy and thermal management systems such as waste heat recovery and refrigeration, respectively. Thermoelectric device design is influenced by the material selection and the device's geometry operating conditions. Therefore, predicting, verifying, and validating thermoelectric device performance using simulations tools is essential to deploying thermoelectric devices in industry. The Multiphysics Object-Oriented Simulation Environment (MOOSE) Framework is an open-source simulation tool capable of modeling simple to complex systems. In this work, we demonstrate MOOSE's thermoelectric device modeling capabilities by simulating a unicouple, module, and exhaust gas recovery system. The Seebeck, Peltier, Thomson, and Joule heating physics are implemented into MOOSE. The MOOSE thermoelectric physics were thoroughly verified and validated using published COMSOL® results and experimental data. In addition, thermoelectric modules were integrated into an exhaust gas recovery system using the MOOSE MultiApp function as a demonstration of the model's ability. The verification and validation results and exhaust gas heat recovery system showcases MOOSE's capability to model thermoelectric devices and integrate these devices into practical energy systems.

42 - ENGINEERING↗
DOE OSTI2024

Enhanced power density in zero-vacuum-gap thermophotovoltaic devices

Thermophotovoltaic (TPV) devices, which convert infrared thermal radiation from a hot emitter into electricity, hold great promise for applications in energy storage and waste heat recovery. While recent advancements have developed TPV devices with high efficiency, much less attention has been focused on improving the power density. Current TPV methods face challenges in significantly boosting the power density using emitters at very high temperatures (>2000 °C) or using complex, costly architectures such as near-field TPV. Here, we present the first experimental demonstration of a novel far-field TPV concept called “zero-vacuum-gap TPV” that eliminates the vacuum or gas-filled gap in conventional designs. By incorporating a high-index, infrared-transparent, and thermally insulating fused quartz spacer, we achieved a two-fold increase in power density compared to the far-field counterpart under identical conditions. Notably, in our experiment, the zero-vacuum-gap far-field design transforms a less-optimized, low-power-density far-field device into one with one of the highest power densities reported at moderate temperatures (700–1100 °C). Moreover, our measurements using a graphite emitter surpass the blackbody limit for gap-integrated far-field devices and match the performance of near-field TPV devices with an ultrathin 200-nm gap. Our findings suggest that zero-vacuum-gap TPV offers potential for cost-effective, scalable manufacturing using current technologies. Additionally, our modelling predicts that further power enhancements over one order of magnitude are possible with other spacer materials.

14 SOLAR ENERGY↗
DOE OSTI2026

Degradation Dynamics of Perovskite Solar Cells Under Fixed Reverse-Current Injection

Previous studies of reverse-bias stability in perovskite solar cells have focused primarily on voltage-controlled tests. Here we instead investigate perovskite solar cell degradation under well-defined, constant reverse-current stress. We show that the choice of hole-transport layer dictates the dominant degradation pathway: cells using thick poly(triphenylamine) (PTAA) layers can tolerate high reverse bias but quickly undergo catastrophic breakdown under fixed reverse current near their one-sun maximum power-point. In contrast, cells modified with phosphonic-acid interface layer MeO-2PACz, with poorer indium-doped tin oxide (ITO) coverage compared to PTAA, exhibit gradual and recoverable degradation under certain stress and recovery conditions. For MeO-2PACz devices, degradation increases with both current magnitude and duration. Importantly, when normalized by injected charge (current times duration), lower currents applied over longer times cause more degradation than higher currents over shorter periods. Here, combining electrical measurements with spatially resolved photoluminescence imaging, our observations support an ion- and charge-mediated interfacial electrochemical degradation mode.

Degradation↗
DOE OSTI2025

High compressive energy absorption and shape recovery behavior of additively manufactured textile-inspired cylindrical braided metamaterials

Mechanical metamaterials (MMs) are engineered structures with unique mechanical properties that arise from their unique spatial arrangement or lattice-like structure. The most commonly designed MMs such as honeycomb and re-entrant auxetics are prone to failure at the sharp corners and weak joints due to the increased stress concentration under deformation. To mitigate this challenge, braided MM structures involving intertwining threads of nylon—forming curved unit cells—have been studied. These textile-inspired cylindrical braided metamaterials (CBMMs) with contrasting unit cells, namely diamond and regular CBMMs, were fabricated by 3D printing. The layer-by-layer deposited structure built by fused filament fabrication delivered an assembly of overlapped threads that are fused at the contact point. To understand deformation behavior of these MMs, finite element models were developed for various load scenarios including quasi-static compression, cyclic and creep loads at room temperature. Stress distribution, deformation mechanisms, and failure modes were analyzed and validated by experiments to analyze the geometries and associated performance. The diamond CBMMs showed stress softening at 30 % compressive strain, withstanding a load of ∼440 N, whereas the regular CBMMs at 50 % strain experienced ∼250 N. The diamond CBMMs delivered higher creep resistance under sustained load and better energy absorption under cyclic loading than the regular CBMMs. The latter, however, exhibited 94 % shape recovery in contrast to 88 % recovery in former prototype during their first cyclic load. In conclusion, this study helps design mechanical lightweight devices that endure significant sustained load and exhibit enhanced energy absorption and shape recovery characteristics in cyclic loading.

Creep↗
DOE OSTI2024

Large Area Near‐Field Thermophotovoltaics for Low Temperature Applications

Abstract Thermophotovoltaics, devices that convert thermal infrared photons to electricity, offer a key pathway for a variety of critical renewable energy technologies including thermal energy storage, waste heat recovery, and direct solar‐thermal power generation. However, conventional far‐field devices struggle to generate reasonable powers at lower temperatures. Near‐field thermophotovoltaics provide a pathway to substantially higher powers by leveraging photon tunneling effects. Here a large area near‐field thermophotovoltaic device is presented, created with an epitaxial co‐fabrication approach, that consists of a self‐supported 0.28 cm 2 emitter‐cell pair with a 150 nm gap. The device generates 1.22 mW at 460 °C, a 25‐fold increase over the same cell measured in a far‐field configuration. Furthermore, the near‐field device demonstrates short circuit current densities greater than the far‐field photocurrent limit at all the temperatures tested, confirming the role of photon tunneling effects in the performance enhancement. Modeling suggests several practical directions for cell improvements and further increases in power density. These results highlight the promise of near‐field thermophotovoltaics, especially for low temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Finding MIDDLE Ground: Scalable and Secure Distributed Learning

Edge computing methods allow devices to efficiently train a high-performing, robust, and personalized model for predictive tasks. However, these methods succumb to privacy and scalability concerns such as adversarial data recovery and expensive model communication. Furthermore, edge computing methods unrealistically assume that all devices train an identical model. In practice, edge devices have varying computational and memory constraints which may not allow certain devices to have the space or speed to train a specific model. To overcome these issues, we propose MIDDLE: a model independent distributed learning algorithm which allows heterogeneous edge devices to assist each other’s training while communicating only non-sensitive information. MIDDLE unlocks the ability for edge devices, regardless of computational or memory constraints, to assist each other even with completely different model architectures. Furthermore, MIDDLE does not require model or gradient communication which greatly reduces communication size and time. We prove that MIDDLE attains the optimal convergence rate O(1/sqrt(TM)) of stochastic gradient descent for convex and non-convex smooth optimization (for total iterations T and batch size M). Finally, our experimental results demonstrate that MIDDLE (even in non-IID data settings) attains robust and high-performing models without model or gradient communication.

Bornstein, Marc I.↗
DOE OSTI2024

InP- and GaAs-Based 0.6 eV GaInAs Devices for Thermophotovoltaics and Laser Power Conversion

Emerging applications such as thermal energy grid storage, waste heat recovery and portable power generation require efficient thermophotovoltaic (TPV) converters tuned to temperatures near 1000 Degrees Celsius or below. Metamorphic GaInAs with larger lattice constants than InP present a promising option for these needs. The ability to grow these devices on GaAs substrates instead of more expensive InP would enhance the scalability of these devices. In this talk, we present inverted metamorphic Ga0.3In0.7As photovoltaic converters with sub-0.60 eV bandgaps grown on InP and GaAs substrates. These devices are realized using InAsP or GaInP/InAsP compositionally graded buffers which exhibit threading dislocation densities of 1.3 +/- 0.6 x 106 cm-2 and 8.9 +/- 1.7 x 106 cm-2 on InP and GaAs, respectively. Despite this difference in defect density, the devices generate similar open-circuit voltages of 0.386 V and 0.383 V, respectively, under irradiance producing a short-circuit current density of -10 A/cm2, with bandgap-voltage offsets of 0.20 and 0.21 V. We estimate their thermophotovoltaic efficiency using these measurements coupled with broadband reflectance measurments. The InP-based cell is estimated to yield 1.09 W/cm2 at 1100 Degrees Celsius vs. 0.92 W/cm2 for the GaAs-based cell, with TPV efficiencies of 16.8 vs. 9.2%. Both devices are limited by sub-bandgap absorption, which we assess largely occurs in the graded buffers. We estimate that the 1100 Degrees Celsius thermophotovoltaic efficiencies would increase to 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application as laser power converters in the 2.0-2.3 um atmospheric window. We estimate efficiencies of 36.8% and 32.5% under 2.0 um monochromatic irradiance of 1.86 W/cm2 and 2.81 W/cm2, respectively.

ENGINEERING,MATERIALS SCIENCE,SOLAR ENERGY↗
DOE OSTI2025

Does class matter? Understanding differential pandemic recovery via a building typology

This study investigates the recovery of building-level footfall from the COVID-19 pandemic using privacy-preserving mobile devices-based footfall data within 60 downtown areas in the USA and Canada. Using clustering, we identify five distinct building typologies based on their characteristics, including rent, quality and recovery rates. The results reveal significant variation of recovery rates by building features. We find negative relationships with footfall recovery for both the percentage of office and remote work tenants and building quality. In contrast, buildings with traditional work tenants and retail functions achieve higher recovery rates. We also test the ‘flight to quality’ hypothesis via on our typology results. High-quality office buildings (Class A+) continue to have high rents but experience low physical footfall recovery, which suggests that this class is not as resilient as portrayed. The findings thus suggest the importance of considering both economic and footfall resilience in evaluating the performance of office buildings.

Covid-19↗
DOE OSTI2026

Degradation Mode Identification by Photocarrier Lifetime Spectroscopy on Devices and Test Structures

In this presentation, I examine the basic concepts of the device physics that can be used to distinguish various degradation and recovery modes on a cell level. The known degradation modes (bulk LeTID and LID, UVID, etc.) are due to defects and impurities that cause the photocarrier recombination according to Shockley-Reed-Hall (SRH) statistics. The SRH recombination rate strongly depends on the balance of electron and hole capture rates into the defects, which in turn, are governed by their local concentrations. The strongest recombination takes place at approximately equal concentrations of electrons and holes, while at low injection conditions (when one type of carrier dominates) the SRH recombination is suppressed. For cell degradation modes that affect the passivated interface (UVID, H-induced TOPCon contact degradation) the defects are at the interface under low-injection conditions due to either high local doping or the adjacent built-in charge in the dielectric. This mode is characterized by changes in the "diode prefactor" J01 slope in the inverse lifetime-injection level curve. In contrast, bulk degradation (LeTID, LID) affects bulk lifetime, with J01 slope unchanged. Carrier lifetime - injection level plots therefore serve as clear indicators of different degradation modes and are shown by experimental examples.

14 SOLAR ENERGY↗
DOE OSTI2026

Switching speed limits in electrically driven VO 2 structural Mott–Peierls transition

Mott materials are archetypal quantum systems actively explored as next-generation electronic and photonic platforms, with potential applications spanning non-Von Neumann computing, robotics, energy storage, and microwave technologies. Among these, vanadium dioxide (VO 2 ) has emerged as one of the most intensively studied compounds, owing to its sharp, near-room-temperature insulator-to-metal phase transition. VO 2 also serves as a benchmark system for testing cutting-edge theories and experimental techniques. Here, we directly visualize the electrically driven transition dynamics in VO 2 using a microwave-driven, frequency-tunable pulsed transmission electron microscope that combines nanometer spatial and picosecond temporal resolution. Under high-frequency (MHz–GHz) excitation, we capture the ultrafast nucleation, propagation, and dissolution of metallic domains within an operating device over millions of reversible cycles. We observe the ultrafast formation of consistent metallic nuclei beneath the electrodes, followed by the propagation of a structural phase front at 4.54 nm/ns. Our experiments show that phonon-mediated structural recovery ultimately limits reversible switching of VO 2 at GHz frequencies, and that a tunable regime for reversible operation spans from kHz to GHz through device engineering. Beyond VO 2 , our approach provides a powerful framework for probing non-equilibrium structural transformations in correlated and functional materials under realistic electrical stimuli.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermochemical renewable energy storage

Systems and methods for energy storage and energy recovery are provided. An electrical-to-electrical energy storage system includes a thermochemical energy storage device, a blower, a compressor, a turbine, and an electrical generator. The TCES device includes a vessel, a porous bed, and a heater. The porous bed is disposed within an interior volume of the vessel. The porous bed comprises a reactive material. The reactive material is configured to release oxygen upon being heated to a reduction temperature, and generate heat when exposed to oxygen. The heater is in thermal contact with the reactive material. The blower is configured to remove oxygen from the interior volume. The compressor is configured to flow oxygen into the interior volume. The turbine is configured to receive a heated, oxygen-depleted gas from the interior volume. The generator is configured to be powered by the turbine to generate electricity.

Klausner, James F.↗
DOE OSTI2026

Toward Lithium Recovery Using Modular (and Membraneless) Phase Separation and Extraction (MPSE) Technology with Ionic Liquid (IL) Solvents: Effect of Coatings

In this work, a single-channel slope-plate Modular and Membrane-less Phase Separation and Extraction (MPSE) device was fabricated using 3D printing. The slope-plate was designed with an insertable glass slide to enable surface modification with coatings. Self-assembled monolayers (SAMs) and perfluoropolyether (Zdol) coatings were applied to tailor surface wettability and enhance phase separation. Using a model biphasic system of water and hexadecane, both coatings significantly improved the separation efficiency compared to the uncoated device by promoting selective wetting. Building on these results, lithium extraction from a simulated saline solution was investigated using 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][NTf₂]) as the ionic liquid (IL) extractant. The IL effectively extracted Li⁺ from the aqueous phase in bulk extraction, demonstrating its potential for lithium recovery. However, the low interfacial tension between the IL and aqueous phases posed challenges for phase separation. The application of SAM and Zdol coatings effectively mitigated this issue. Overall, integrating tailored surface chemistry with the slope-plate MPSE design shows great promise as an efficient and scalable platform for studying liquid–liquid separation and optimizing ionic liquid–based extraction processes for lithium recovery from saline sources.

3D printing↗
DOE OSTI2025

Dynamic disulfide bond networks enable self-healable and mechanically resilient intrinsically stretchable organic solar cells

A dynamic disulfide network introduced into donor/acceptor blends enables room-temperature self-healing and mechanical resilience in intrinsically stretchable organic solar cells, achieving performance recovery after high mechanical strain. The development of intrinsically stretchable organic solar cells (IS-OSCs) faces significant challenges in balancing mechanical durability and optoelectronic performance. Conventional π-conjugated polymer-based donor/acceptor blend films often exhibit limited stretchability and irreversible performance degradation under mechanical strain. To address these limitations, we propose a novel self-healable donor/acceptor blended film with a dual-network morphology, achieved by incorporating a dynamic disulfide bond-based crosslinked network into the bulk-heterojunction film. The resulting thin films demonstrate a power conversion efficiency (PCE) of 16.39% in rigid OSC devices and a fracture strain of 15.6%. Remarkably, the IS-OSCs retain 80% of their initial PCE under 30% strain and exhibit performance recovery after multiple stretch-release cycles at 40% strain through a room-temperature self-healing process. This work provides a proof-of-concept for highly stretchable and durable IS-OSCs, offering valuable insights for advancing the field of wearable energy systems, adaptive solar textiles, and sustainable electronics.

Yang, Wenyu↗
DOE OSTI2024

Coupling Microdroplet-Based Sample Preparation, Multiplexed Isobaric Labeling, and Nanoflow Peptide Fractionation for Deep Proteome Profiling of the Tissue Microenvironment

There is increasing interest in developing in-depth proteomic approaches for mapping tissue heterogeneity in a cell-type-specific manner to better understand and predict the function of complex biological systems such as human organs. Existing spatially resolved proteomics technologies cannot provide deep proteome coverage due to limited sensitivity and poor sample recovery. Herein, we seamlessly combined laser capture microdissection with a low-volume sample processing technology that includes a microfluidic device named microPOTS (microdroplet processing in one pot for trace samples), multiplexed isobaric labeling, and a nanoflow peptide fractionation approach. The integrated workflow allowed us to maximize proteome coverage of laser-isolated tissue samples containing nanogram levels of proteins. We demonstrated that the deep spatial proteomics platform can quantify more than 5000 unique proteins from a small-sized human pancreatic tissue pixel (∼60,000 μm2) and differentiate unique protein abundance patterns in pancreas. Furthermore, the use of the microPOTS chip eliminated the requirement for advanced microfabrication capabilities and specialized nanoliter liquid handling equipment, making it more accessible to proteomic laboratories.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Lessons Learned: Summary of Insights From the HERO WEC and Waves to Water Deployments Between 2022 and 2024

In 2020, a team from the National Renewable Energy Laboratory (NREL) partnered with the East Carolina University Coastal Studies Institute to develop a small, modular, wave-powered point absorber desalination prototype. That prototype, known as the hydraulic and electric reverse osmosis wave energy converter (HERO WEC), was intended to de-risk the installation activities planned for the Waves to Water Prize sponsored by the Water Power Technologies Office. The NREL team was given approximately 18 months to design, build, bench test, and deploy the HERO WEC prototype. Since the initial HERO WEC development, it has been used for two in-lab test programs and three ocean deployments. The first in-lab test program focused on ensuring that the overall operation of the device occurred as expected and on validating the operation of safety systems such as pressure relief valves or electrical breakers for load mitigation. The second in-lab test program was the first time the NREL team leveraged NREL’s large-amplitude motion platform to characterize the performance of the HERO WEC. Of the three in-water deployments, the first deployment was effectively an installation and recovery practice with no meaningful wave activity during the time that it was installed. The second deployment was a 2-week effort that enabled both the electric and hydraulic configurations of the device to be in the water for approximately 5 days each. This deployment was also the first time that the team had the opportunity to perform a drivetrain swap on the Coastal Studies Institute research vessel. The third deployment had to be split into two separate installations due to minor damage incurred from the WEC spinning during the initial installation. This report summarizes the deployments, the challenges encountered with each deployment, and the lessons learned for future work.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Fluorophilic Sigma(σ)‐Lock Self‐Healable Copolymers

Abstract Although F‐Containing molecules and macromolecules are often used in molecular biology to increase the binding with Lewis acidic groups by introducing favorable C−F dipoles, there is virtually no experimental evidence and limited understanding of the nature of these interactions, especially their role in synthetic polymeric materials. These studies elucidate the molecular origin of inter‐ and intra‐Chain interactions responsible for self‐healing of F‐Containing copolymers composed of pentafluorostyrene and n‐butyl acrylate units (p(PFS/nBA). Guided by dynamic surface oscillating force (SOF) and spectroscopic measurements supported by molecular dynamics (MD) simulations, these studies show that the reformation of σ‐σ orbitals in −C−F of PFS and CH 3 CH 2 − of nBA units enables the recovery of entropic energy via fluorophilic‐σ‐lock van der Waals forces when PFS/nBA molar ratios are ~50/50. The strength of these interactions determined experimentally for self‐healable PFS/nBA compositions is in the order ~0.3 kcal/mol which primarily comes from fluorophilic‐σ‐lock (~70 %) contributions. These interactions are significantly diminished for non‐self‐healable counterparts. Strongly polarized −C−F σ orbitals create lateral dipolar forces enhancing the affinity towards −C−H orbitals, facilitating energetically favorable interactions. Entropic recovery driven by non‐Covalent bonding offers a valuable tool in designing materials with unique functionalities, particularly self‐healable batteries and energy storage devices.

Gaikwad, Samruddhi↗
DOE OSTI2026

Design, characterization and shape recovery behavior of 3D/4D printed shape memory polymers (SMPs)

Shape memory polymers (SMPs) represent a paradigm shift in material science, uniquely capable of undergoing reversible shape transformations triggered by external stimuli, positioning them as pivotal in developing next-generation biomedical devices, aerospace components, and adaptive structures. Extensive research has been done on SMPs with a major focus on high-temperature programming methods, which can limit energy efficiency and applicability with temperature-sensitive materials. Additionally, while various SMP blends have demonstrated great potential, limited work has been done on the suitability for 3D printing these materials, particularly under high-strain and ambient temperature programming conditions. In this study, a three-component optimized SMP composition was evaluated by 3D printing via the Material Extrusion (MEX) technique and investigating its ambient temperature-programming behavior at high strains. The SMP formulation studied was a tailored blend of thermoplastic polyurethane (TPU), polycaprolactone (PCL), and an octadecane diol-based copolymer (OBC) that exhibits robust shape memory behavior, high strain tolerance, and efficient force generation. Rigorous thermal, mechanical, and shape recovery analyses, along with optimized printing parameters and consistent shape recovery rates of up to 90%, were achieved under dynamic mechanical analysis (DMA), even under ambient programming conditions. This work demonstrates the SMP composition’s potential for adaptive, self-deployable systems with 4D printing characteristics ideal for bio-inspired structures and artificial muscle fibers.

Sudan, Kavish [University of Louisville, KY]↗