Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Noise characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Pre-Launch Noise Characterization of the Landsat-7 Enhanced Thematic Mapper Plus (ETM Plus)

A noise characterization of the Landsat-7 Enhanced Thematic Mapper Plus (ETM+) instrument was performed as part of a near-real time performance assessment and health monitoring program. Perl'ormance data for the integrated Landsat-7 spacecraft and ETM+ were collected before, during, and after the spacecraft thermal vacuum testing program at the Lockheed Martin Missiles and Space (LMMS) facilities in Valley Forge, PA. The Landsat-7 spacecraft and ETM+ instrument were successfully launched on April 15, 1999. The spacecraft and ETM+ are now nearing the end of the on orbit engineering checkout phase, and Landsat-7 is expected to be declared operational on or about July 15, 1999. A preliminary post-launch noise characterization was performed and compared with the pre-launch characterization. In general the overall noise levels in the ETM+ are at or below the specification levels. Coherent noise is seen in most bands, but is only operationally significant when imaging in (he panchromatic band (band 8). This coherent noise has an amplitude as high as approximately 3 DN (peak-to-peak, high gain) at the Nyquist rate of 104 kHz, and causes the noise levels in panchromatic band images at times to exceed the total noise specification by up to approximately 10%. However, this 104 kHz noise is now much weaker than it was prior to the successful repair of the ETM+ power supplies that was completed in May 1998. Weak and stable coherent noise at approximately 5 kHz is seen in all bands in the prime focal plane (bands 1-4 and 8) with the prime (side A) electronics. Very strong coherent noise at approximately 20 kHz is seen in a few detectors of bands 1 and 8, but this noise is almost entirely in the turn-around region between scans when the ETM+ is not imaging the Earth. Strong coherent noise was seen in 2 detectors of band 5 during some of the pre-launch testing; however, this noise seems to be temperature dependent, and has not been seen in the current on orbit environment. Strong 91 kHz coherent noise was observed in the redundant (side B) panchromatic band data after the completion of spacecraft thermal vacuum testing. The cause of this coherent noise was identified as a failed capacitor that was replaced prior to launch, and this noise has not been seen on orbit.

Pedelty, J. A.↗
NASA NTRS2001

Earth Observing-1 Advanced Land Imager: Dark Current and Noise Characterization and Anomalous Detectors

The dark current and noise characteristics of the Earth Observing-1 Advanced Land Imager measured during ground calibration at MIT Lincoln Laboratory are presented. Data were collected for the nominal focal plane operating temperature of 220 K as well as supplemental operating temperatures (215 and 225 K). Dark current baseline values are provided, and noise characterization includes the evaluation of white, coherent, low frequency, and high frequency components. Finally, anomalous detectors, characterized by unusual dark current, noise, gain, or cross-talk properties are investigated.

Mendenhall, J. A.↗
NASA NTRS1988

LANDSAT-4 and LANDSAT-5 Multispectral Scanner Coherent Noise Characterization and Removal

A technique is described for characterizing the coherent noise found in LANDSAT-4 and LANDSAT-5 MSS data and a companion technique for filtering out the coherent noise. The techniques are demonstrated on LANDSAT-4 and LANDSAT-5 MSS data sets, and explanations of the noise pattern are suggested in Appendix C. A cookbook procedure for characterizing and filtering the coherent noise using special NASA/Goddard IDIMS functions is included. Also presented are analysis results from the retrofitted LANDSAT-5 MSS sensor, which shows that the coherent noise has been substantially reduced.

Tilton, James C.↗
NASA NTRS2018

ATMS Radiometric Noise Characterization

The Advanced Technology Microwave Sounder (ATMS), on SNPP and NOAA-20, provides vertical atmospheric temperature and moisture profiles that are a key input to numerical weather prediction. Full characterization of radiometric noise is critical to error modeling, algorithm development and the potential development of performance requirements and product improvements. This paper presents estimates of white noise and low-frequency 1/f noise as derived from the Allan variance and scan-to-scan autocorrelations of data from the internal hot calibration. This approach allows direct comparison of on-orbit performance of the two units as well as comparison between ground calibration test data and on-orbit performance. The autocorrelation at multiple scan intervals is used as input to a theoretical model of the NET of inferred scene brightness temperature, when using weighted samples of calibration data over multiple scans. This will support selection of optimized calibration weighting functions for each channel, as well as providing further insight into the striping phenomenon. These measured autocorrelations are also compared to the autocorrelations derived from the 1/f spectra obtained both in special ground and on-orbit tests that characterize gain fluctuation. Channel cross-correlations are also presented, which can have a significant impact on effectiveness of direct assimilation performance.

instrument calibration↗
NASA NTRS1985

Landsat-4 and Landsat-5 MSS coherent noise - Characterization and removal

The Multispectral Scanner (MSS) remote sensing instrument carried by Landsat-4 and Landsat-5 is similar to MSS instruments carried by Landsat-1, Landsat-2, and Landsat-3. However, the addition of the Thematic Mapper (TM) instrument to Landsat-4 and Landsat-5 required several design changes in the MSS instruments carried on these satellites because of the lower orbit and new satellite platform. Data from the MSS onboard the Landsat-4 and Landsat-5 satellites were found to be generally comparable to the data obtained in the case of the earlier Landsat MSSs. However, a coherent noise pattern was observed in the Landsat-4 MSS data. In the present paper, the conduction of a noise analysis is discussed along with the noise characterization results, and a technique through which the Landsat-4 MSS coherent noise can be removed.

Tilton, J. C.↗
DOE OSTI2023

BEYONDPLANCK VI. Noise characterization and modeling

We present a Bayesian method for estimating instrumental noise parameters and propagating noise uncertainties within the global BeyondPlanck Gibbs sampling framework, and apply this to Planck Low Frequency Instrument (LFI) time-ordered data. Following previous literature, we initially adopt a 1/ f model for the noise power spectral density (PSD), but find the need for an additional lognormal component in the noise model for the 30 and 44 GHz bands. We implement an optimal Wiener-filter (or constrained realization) gap-filling procedure to account for masked data. We then use this procedure to both estimate the gapless correlated noise in the time-domain, n corr , and to sample the noise PSD parameters, ξ n = {σ 0 , f knee , α, A p }. In contrast to previous Planck analyses, we assume piecewise stationary noise only within each pointing period (PID), not throughout the full mission, but we adopt the LFI Data Processing Center (DPC) results as priors on α and f knee . On average, we find best-fit correlated noise parameters that are mostly consistent with previous results, with a few notable exceptions. However, a detailed inspection of the time-dependent results reveals many important findings. First and foremost, we find strong evidence for statistically significant temporal variations in all noise PSD parameters, many of which are directly correlated with satellite housekeeping data. Second, while the simple 1/ f model appears to be an excellent fit for the LFI 70 GHz channel, there is evidence for additional correlated noise not described by a 1/ f model in the 30 and 44 GHz channels, including within the primary science frequency range of 0.1–1 Hz. In general, most 30 and 44 GHz channels exhibit deviations from 1/ f at the 2–3σ level in each one hour pointing period, motivating the addition of the lognormal noise component for these bands. For some periods of time, we also find evidence of strong common mode noise fluctuations across the entire focal plane. Overall, we conclude that a simple 1/ f profile is not adequate to fully characterize the Planck LFI noise, even when fitted hour-by-hour, and a more general model is required. These findings have important implications for large-scale CMB polarization reconstruction with the Planck LFI data, and the current work is a first attempt at understanding and mitigating these issues.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2015

On-Orbit Noise Characterization of MODIS Reflective Solar Bands

The Moderate Resolution Imaging Spectroradiometer (MODIS), launched on the Terra and Aqua spacecrafts, was designed to collect complementary and comprehensive measurements of the Earth's properties on a global scale. The 20 reflective solar bands (RSBs), covering a wavelength range from 0.41 to 2.1 micrometers, are calibrated on-orbit using regularly scheduled solar diffuser (SD) observations. Although primarily used for on-orbit gain derivation, the SD observations also facilitate the characterization of the detector signal-to-noise ratio (SNR). In addition to the calibration requirement of 2% for the reflectance factors and 5% for the radiances, the required SNRs are also specified for all RSB at their typical scene radiances. A methodology to characterize the on-orbit SNR for the MODIS RSB is presented. Overall performance shows that a majority of the RSB continue to meet the specification, therefore performing well. A temporal decrease in the SNR, observed in the short-wavelength bands, is attributed primarily to the decrease in their detector responses. With the exception of the inoperable and noisy detectors in band 6 identified prelaunch, the detectors of AquaMODIS RSB perform better than TerraMODIS. The approach formulated for on-orbit SNR characterization can also be used by other sensors that use on-board SDs for their on-orbit calibration (e.g., Suomi National Polar-Orbiting Partnership [SNPP]-Visible Infrared Imaging Radiometer Suite).

Reflective↗
NASA NTRS1996

Semiconductor Laser Low Frequency Noise Characterization

This work summarizes the efforts in identifying the fundamental noise limit in semiconductor optical sources (lasers) to determine the source of 1/F noise and it's associated behavior. In addition, the study also addresses the effects of this 1/F noise on RF phased arrays. The study showed that the 1/F noise in semiconductor lasers has an ultimate physical limit based upon similar factors to fundamental noise generated in other semiconductor and solid state devices. The study also showed that both additive and multiplicative noise can be a significant detriment to the performance of RF phased arrays especially in regard to very low sidelobe performance and ultimate beam steering accuracy. The final result is that a noise power related term must be included in a complete analysis of the noise spectrum of any semiconductor device including semiconductor lasers.

SEMICONDUCTOR LASERS↗
NASA NTRS2007

Detector Noise Characterization and Performance of MODIS Thermal Emissive Bands

MODIS has 16 thermal emissive bands, a total of 160 individual detectors (10 for each spectral bands), located on the two cold focal plane assemblies (CFPA). MODIS TEB detectors were fully characterized pre-launch in a thermal vacuum (TV) environment using a NIST traceable blackbody calibration source (BCS) with temperatures ranging from 170 to 340K. On-orbit the TEB detectors are calibrated using an on-board blackbody (BB) on a scan-by-scan basis. For nominal on-orbit operation, the on-board BB temperature is typically controlled at 285K for Aqua MODIS and 290K for Terra MODIS. For the MODIS TEB calibration, each detector's noise equivalent temperature difference (NEdT) is often used to assess its performance and this parameter is a major contributor to the calibration uncertainty. Because of its impact on sensor calibration and data product quality, each MODIS TEB detector's NEdT is monitored on a daily basis at a fixed BB temperature and completely characterized on a regular basis at a number of BB temperatures. In this paper, we describe MODIS on-orbit TEB NEdT characterization activities, approaches, and results. We compare both pre-launch and on-orbit performance with sensor design specification and examine detector noise characterization impact on the calibration uncertainty. To date, 135 TEB detectors (out of a total of 160 detectors) in Terra MODIS (launched in December 1999) and 158 in Aqua MODIS (launched in May 2002) continue to perform with their NEdT below (or better than) their design specifications. A complete summary of all TEB noisy detectors, identified both pre-launch and on-orbit, is provided.

Xiong, X.↗
NASA NTRS1983

Noise characterization and minimization of a precision gyroscopic rate sensor

A program has been conducted to evaluate the noise signature of Space Telescope gyros. The Space Telescope gyros provide a three-axis attitude reference using six single-degree-of-freedom gyroscopes operated with pulse rebalance electronics; the rate sensor attitude quantization is 0.00025 arcsec. The results of the noise evaluation program, including error source characterization and identification of candidate design modifications, are summarized together with the results of prototype hardware testing. It is shown that the proposed design modifications can significantly improve the rate sensor noise performance.

Dougherty, H.↗
NASA NTRS2008

On-Orbit Noise Characterization for MODIS Reflective Solar Bands

Since launch, the Moderate Resolution Imaging Spectroradiometer (MODIS) has operated successfully on-board the NASA Earth Observing System (EOS) Terra and EOS Aqua spacecraft. MODIS is a passive cross-track scanning radiometer that makes observations in 36 spectral bands with spectral wavelengths from visible (VIS) to long-wave infrared. MODIS bands 1-19 and 26 are the reflective solar bands (RSB) with wavelengths from 0.41 to 2.2 micrometers. They are calibrated on-orbit using an on-board solar diffuser (SD) and a SD stability monitor (SDSM) system. For MODIS RSB, the level 1B calibration algorithm produces top of the atmosphere reflectance factors and radiances for every pixel of the Earth view. The sensor radiometric calibration accuracy, specified at each spectral band's typical scene radiance, is 2% for the RSB reflectance factors and 5% for the RSB radiances. Also specified at the typical scene radiance is the detector signal-to-noise ratio (SNR), a key sensor performance parameter that directly impacts its radiometric calibration accuracy and stability, as well as the image quality. This paper describes an on-orbit SNR characterization approach developed to evaluate and track MODIS RSB detector performance. In order to perform on-orbit SNR characterization, MODIS RSB detector responses to the solar illumination reflected from the SD panel must be corrected for factors due to variations of the solar angles and the SD bi-directional reflectance factor. This approach enables RSB SNR characterization to be performed at different response levels for each detector. On-orbit results show that both Terra and Aqua MODIS RSB detectors have performed well since launch. Except for a few noisy or inoperable detectors which were identified pre-launch, most RSB detectors continue to meet the SNR design requirements and are able to maintain satisfactory short-term stability. A comparison of on-orbit noise characterization results with results derived from pre-launch calibration and characterization are also provided.

Xiong, X.↗
NASA NTRSDate not supplied

Fundamental Noise Characterization of a Ducted Propeller in Hover

Unmanned aerial vehicles (UAVs) are currently being used for reconnaissance missions, tactical surveillance, and infrastructure inspection. When legislation allows it, these devices will provide additional services close to inhabited areas, which could lead to noise complaints. On most UAVs, the propellers are the dominant source of noise. As a result, researchers have studied the impact of propeller shape and blade count on noise. Much of this work, however, has focused on isolated propellers. While different UAV concepts are equipped with ducts for aerodynamic and protection reasons, few studies focus on the acoustic benefit of ducts, as is achieved, for example, on turbofan aircraft. The objectives of this paper are: first, to simulate the noise radiation of a UAV propeller in static conditions based on its location in a hard wall duct; second, to analyze the contribution of the different acoustic source components (i.e., thrust, torque, and thickness); and third, to validate the approach with experiments conducted in the NASA Small Hover Anechoic Chamber over a range of propeller rotation rates. For the propeller and duct geometries considered in this experiment, it is shown that the best attenuation is achieved when the propeller is centered axially in the duct because of interference between upstream and downstream radiated waves.

ducted propeller↗
NASA NTRSDate not supplied

EVALUATION OF ACOUSTIC SNAPSHOT ARRAYS FOR ROTORCRAFT SOURCE NOISE CHARACTERIZATION

Historical development of acoustic hemispheres has required steady flight of a rotorcraft vehicle across a large linear array of microphones. The US Army, NASA, and Navy recently conducted a rotorcraft acoustics flight test in which multiple “snapshot” microphone arrays were used alongside a traditional linear microphone array. The snapshot arrays allow for a near instantaneous capture of rotorcraft acoustic emissions, without the need for steady flight. Development of the snapshot array is contained herein, and an evaluation of effectiveness of the array during adverse weather conditions. The snapshot arrays captured significant variation in acoustic emissions throughout a single run and between multiple runs of similar conditions. Hemispheres were created and modelled in land-use planning software and an investigation of A-weighted Sound Exposure Level (SEL [dBA]) was conducted. Sideline predictions of SEL compared well (within 0.1 dBA) between traditional and snapshot arrays, while centre line locations were less favourable with a difference of 1.6 dBA. Future refinement is required for the snapshot array technique, including advanced design of microphone placement and employing a semiempirical method to interpolate between measurement points, instead of the linear frequency weighting conventionally employed.

Rotorcraft↗
DOE OSTI2023

Multiqubit noise deconvolution and characterization

We present a noise deconvolution technique for obtaining noiseless expectation values of noisy observables at the output of multiqubit quantum channels. For any number of qubits or in the presence of correlations, our protocol applies to any mathematically invertible noise model, even when its inverse map is not physically implementable, i.e., when it is neither completely positive nor trace preserving. For a generic observable affected by Pauli noise it provides a quadratic speedup, always producing a rescaling of its Pauli basis components. We show that it is still possible to achieve the deconvolution while experimentally estimating the noise parameters, whenever these are unknown (bypassing resource-heavy techniques such as quantum process tomography). We provide a simulation, with examples for both Pauli and non-Pauli channels.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗