SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A power regulation system incorporating n-parallel power supplies employing PWM switching regulators is studied. Analysis of individual unit operation and coupled-system parameter sensitivity is considered from an operations viewpoint. A detailed example is included to illustrate parallel system operation for 18 such units powered by solar-cell banks.
Results for the vibration measured at five locations on the fuselage structure during static operations are presented. The analysis was concerned with the magnitude of the vibration and the relative phase between different locations, the frequency response (inertance) functions between the exterior pressure field and the vibration, and the coherent output power functions at interior microphone locations based on sidewall vibration. Fuselage skin panels near the plane of rotation of the propeller accept propeller noise excitation more efficiently than they do exhaust noise.
The objectives of the UVSP experiment are to study solar ultraviolet radiations, particularly from flares and active regions, and to measure constituents in the terrestrial atmosphere by the extinction of sunlight at satellite dawn and dusk. The instrument is designed to observe the Sun at a variety of spectral and spatial resolutions in the range from 1150 to 3600 A. A Gregorian telescope with effective focal length of 1.8 m is used to feed a 1 m Ebert-Fastie spectrometer. A polarimeter containing rotatable magnesium fluoride waveplates is included behind the spectrometer entrance slit and will allow all four Stokes parameters to be determined. Velocities on the Sun can also be measured. The instrument is controlled by a computer which can interact with the data stream to modify the observing program. The observing modes, including rasters, spectral scans, velocity measurements, and polarimetry, are also described along with plans for mission operations, data handling, and analysis of the observations.
Basic design criteria are given for an ion mass spectrometer for use in studying magnetospheric ion populations. The proposed instrument is composed of an electrostatic analyzer followed by a magnetic spectrometer and simultaneously measures the energy per unit and mass per unit charge of the ion species. An electromagnet is used for momentum analysis to extend the operational energy range over a much wider domain than is possible with the permanent magnets used in previous flights. The energetic ion source regions, ion energization mechanisms, field line tracing, coordinated investigations, and orbit considerations are discussed and operations of the momentum analyzer and of the electrostatic energy analyzer are examined.
The performance, costs, organization and other characteristics of both the manual system and AIDS 2 were used to establish a baseline case. The results of the evaluation are to be used to determine the feasibility of the AIDS 3 System, as well as provide a basis for ranking alternative systems during the second phase of the JPL study. The results of the study were tabulated by subject, scope and methods, providing a descriptive, quantitative and qualitative analysis of the current operating systems employed by the FBI Identification Division.
An integrated gas analysis system designed to operate in automatic, semiautomatic, and manual modes from a remote control panel is described. The system measures the carbon monoxide, oxygen, water vapor, total hydrocarbons, carbon dioxide, and oxides of nitrogen. A pull through design provides increased reliability and eliminates the need for manual flow rate adjustment and pressure correction. The system contains two microprocessors to range the analyzers, calibrate the system, process the raw data to units of concentration, and provides information to the facility research computer and to the operator through terminal and the control panels. After initial setup, the system operates for several hours without significant operator attention.
In 1977, California Law AB452 was passed to provide a mandate for the California Department of Forestry (CDF) to design and implement an information system to assess the forest land base for multiple uses and values. In connection with this mandate, a land-cover map of the entire state, emphasizing forest types, was produced. In producing this map, the latest techniques in digital image mosaicking were combined with the highspeed processing capability available on the ILLIAC IV parallel processor and other computer systems at the Ames Research Center (ARC). An operational and very responsive analysis method was developed at ARC that permitted on-time response to weekly workshops conducted with CDF field personnel to identify all 1,200 spectral classes and to produce final products. Over 100,000,000 acres were classified in the period between December 1, 1978, and April 15, 1979. All analyses were conducted using existing software.
The establishment of image analysis facilities for the operational utilization of LANDSAT data in Idaho, Oregon, and Washington is discussed. The hardware and software resources are described for each facility along with the range of services.
Optical spot-raster scanner produces weighted photoresponse image (PI) of operating CMOS IC. Digital analysis of PI's, which correlates differences in PI's with electrical behavior of IC, shows promise both as 100-percent screening method for use in IC manufacture and as diagnostic tool in IC development.
A numerical procedure was developed for the aerodynamic force and moment analysis of V/STOL aircraft operating in the transition regime between hover and conventional forward flight. The trajectories, cross sectional area variations, and mass entrainment rates of the jets are calculated by the Adler-Baron Jet-in-Crossflow Program. The inviscid effects of the interaction between the jets and airframe on the aerodynamic properties are determined by use of the MCAIR 3-D Subsonic properties are determined by use of the MCAIR 3-D Subsonic Potential Flow Program, a surface panel method. In addition, the MCAIR 3-D Geometry influence Coefficient Program is used to calculate a matrix of partial derivatives that represent the rate of change of the inviscid aerodynamic properties with respect to arbitrary changes in the effective wing shape.
Orbital Transfer Vehicle (OTV) servicing study scope, propellant transfer, storage and reliquefaction technology development missions (TDM), docking and berthing TDM, maintenance TDM, OTV/payload integration TDM, combined TDMS design, summary space station accomodations, programmatic analysis, and TDM equipment operational usage are discussed.
CO2 lidar systems technology and signal processing requirements relevant to measurement needs and sensitivity are discussed. Doppler processing is similar to microwave radar, with signal reception controlled by a computer capable of both direct and heterodyne operations. Trace gas concentrations have been obtained with the NASA DIAL system, and trace gas transport has been determined with Doppler lidar measurements for wind velocity and turbulence. High vertical resolution measurement of trace gases, wind velocity, and turbulence are most important in the planetary boundary layer and in regions between the PBL and the lower stratosphere. Shear measurements are critical for airport operational safety. A sensitivity analysis for heterodyne detection with the DIAL system and for short pulses using a Doppler lidar system is presented. The development of transient injection locking techniques, as well as frequency stability by reducing chirp and catalytic control of closed cycle CO2 laser chemistry, is described.
An analysis of the flight dynamics and piloted control characteristics of the Helistat, a quadrotor heavy-lift airship, was completed using the HYBRDS airship simulation facility. The analysis covered the full operating flight envelope, including likely ranges of altitude, airspeed, sideslip, and loading variations. Particular areas of study were performance, trim, power requirements, linearized dynamics, handling qualities, and mooring operations. The key assumptions were: a rigid vehicle, no control system dynamics, fixed rotor and propeller RPM, and no ballonet dynamics. The nominal cruise speed for the H34 engines operating at 1275 HP was found to be 40-50 kts, depending on the loading condition. The maximum payload capability was calculated as 45,000 lbs for sea level-based operations. The crosswind capability in hover is 5-10 kts depending on the loading conditions, but this requires excessive roll angle due to the roll-to-translate control gearing. Sideslip angles of 110-135 degrees (wind from aft quarters) are critical for directional trim and stability, and should be avoided.
A software package enabling engineers to conduct experiments to determine the actual performance of long constraint-length convolutional codes over the Voyager 1 communication link directly from the Jet Propulsion Laboratory (JPL) has been developed. Using this software, engineers are able to enter test data from the Laboratory in Pasadena, California. The software encodes the data and then sends the encoded data to a personal computer (PC) at the Goldstone Deep Space Complex (GDSC) over telephone lines. The encoded data are sent to the transmitter by the PC at GDSC. The received data, after being echoed back by Voyager 1, are first sent to the PC at GDSC, and then are sent back to the PC at the Laboratory over telephone lines for decoding and further analysis. All of these operations are fully integrated and are completely automatic. Engineers can control the entire software system from the Laboratory. The software encoder and the hardware decoder interface were developed for other applications, and have been modified appropriately for integration into the system so that their existence is transparent to the users. This software provides: (1) data entry facilities, (2) communication protocol for telephone links, (3) data displaying facilities, (4) integration with the software encoder and the hardware decoder, and (5) control functions.
The background for the CSM Testbed Architecture and a description of the three architecture related tasks under the NASA/Langley CSM contract (NAS1-18444) are given. For each task the objectives, subtasks chosen to achieve the objectives, and the accomplishments are presented. For Task 2, Near-Term Enhancements to the CSM Testbed Architecture, the primary objectives are to quickly correct: (1) inefficiency in the GAL data manager, and (2) deficiency in the CLIP-interpreted command language, CLAMP. The corresponding modifications should preserve upward-compatibility to a reasonable extent, while at the same time increasing the flexibility and extensibility of the CSM Testbed. Researchers have increased the efficiency of GAL by a factor of 2+ and have made several improvements in CLIP. For Task 5, Matrix Algebra Methods and Utilities, the goal is to investigate the current capabilities of the CSM Testbed and the required improvements to the CSM Testbed for performing the matrix algebraic operations required for the analysis of present and future CSM focal problems using advanced methods. Researchers have made an extensive study of the matrix algebra functions in SPAR that includes documenting these routines and supplying inline comments.
Sample Experiment denotes the set of all operations that include collection, analysis, packaging, and environmental control of atmospheric and geologic samples of Mars. Various functions may be distributed among surface roving vehicles, stationary landers, and spacecraft but the Sample Experiment remains an integrated mission activity that extends from Mars landing through delivery of the sample payload to the recieving facility on Earth. Technological challenges not faced in previous planetary missions include development of robotic systems to manipulate and characterize samples and to reliably seal them in containers with minimal contamination or degradation.
Three separate tasks which supported the test preparation, test operations, and post test analysis of the NASA Ames flight test evaluation of the differential Global Positioning System (GPS) are presented. Task 1 consisted of a navigation filter design, coding, and testing to optimally make use of GPS in a differential mode. The filter can be configured to accept inputs from external censors such as an accelerometer and a barometric or radar altimeter. The filter runs in real time onboard a NASA helicopter. It processes raw pseudo and delta range measurements from a single channel sequential GPS receiver. The Kalman filter software interfaces are described in detail, followed by a description of the filter algorithm, including the basic propagation and measurement update equations. The performance during flight tests is reviewed and discussed. Task 2 describes a refinement performed on the lateral and vertical steering algorithms developed on a previous contract. The refinements include modification of the internal logic to allow more diverse inflight initialization procedures, further data smoothing and compensation for system induced time delays. Task 3 describes the TAU Corp participation in the analysis of the real time Kalman navigation filter. The performance was compared to that of the Z-set filter in flight and to the laser tracker position data during post test analysis. This analysis allowed a more optimum selection of the parameters of the filter.
Dexterous manipulation and grasping in telerobotic systems depends on the integration of high-performance sensors, displays, actuators and controls into systems in which careful consideration has been given to human perception and tolerance. Research underway at the Wisconsin Center for Space Automation and Robotics (WCSAR) has the objective of enhancing the performance of these systems and their components, and quantifying the effects of the many electrical, mechanical, control, and human factors that affect their performance. This will lead to a fundamental understanding of performance issues which will in turn allow designers to evaluate sensor, actuator, display, and control technologies with respect to generic measures of dexterous performance. As part of this effort, an experimental test bed was developed which has telerobotic components with exceptionally high fidelity in master/slave operation. A Telerobotic Performance Analysis System has also been developed which allows performance to be determined for various system configurations and electro-mechanical characteristics. Both this performance analysis system and test bed experiments are described.