Minimum Joint Gap for Robotic Welder
Report describes evaluation of factors influencing minimum-gap requirement for robot-welded joint. Evaluations part of series on vision-based welding-control system.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Report describes evaluation of factors influencing minimum-gap requirement for robot-welded joint. Evaluations part of series on vision-based welding-control system.
The mechanism which will be used on the space station to position the solar arrays and radiator panels for Sun pointing and Sun avoidance is described. The unique design features will be demonstrated on advanced development models of two of the joints being fabricated under contract to NASA-MSFC.
O-ring response and sealing in pressurized shell structures is examined. The study found that the key elements in the failure of the seal to be joint opening and rotation, assembly out of roundness, and O-ring seal response.
A block diagram showing plant dynamics in normal mode coordinates, a linear feedback controller with command limits, and actuator dynamics with rate and displacement limits is given. The objective is to examine the effects of joint rate and displacement saturation limits on the stability regions. An unstable short period dynamic model is transformed into normal mode coordinates and is augmented with actuator dynamics. A linear feedback controller is used to provide closed-loop stability. The stability with constrained actuator rate limits under varying bandwidth, displacement and command limits is examined.
A discussion of current standard durability prediction methodology for bonded joints is given. The influence of time-dependent adhesive properties on lap shear stress distributions and interfacial stresses is presented. It is suggested that these effects may be important in durability considerations. Test geometries from which better durability information can be obtained are outlined and a general mechanics approach for durability prediction is suggested.
A study was conducted to investigate the stress ratio effect on cyclic debond growth behavior in adhesively bonded composite joints. The system studied consisted of graphite/epoxy adherends bonded with a toughened epoxy adhesive. This study showed that the strain energy release rate range was the driving factor for cyclic debonding of the tested bonded system when subjected to cyclic loads with different stress ratios for both mode I and mixed mode I-II loadings.
Input gain weighting added to existing adaptive-control algorithm. Report discusses concept for adaptive control of rotations of various appended structures about joints on space station, with suppression of vibrations in both station and appendages. Concept relevant to such terrestrial applications as control of aircraft, suppression of vibrations in large buildings, and robotics.
The Combined Release and Radiation Effects Satellite (CRRES) program is a two-phase joint USAF/NASA program consisting of a low Earth orbit (LEO) phase and a geosynchronous transfer orbit (GTO) phase. The mission has been carefully planned to help clarify the geospace environment picture and its effects on space hardware, communications, and man. CRRES instruments were selected for synergism, accuracy, and applicability, and will be cross-calibrated for consistency. They will provide data to fill the gaps in geospace modeling data already obtained, and will update and correct existing models. The chemical release experiments and low altitude instruments will clarify the character of the ionosphere in low Earth orbit and the high altitude chemical release experiments will improve knowledge of how trapped particle populations behave out as far as synchronous altitudes. The ionospheric studies will lead to significantly improved Earth-space intercommunications.
To evaluate the potential for spacecraft damage caused by activation of pyrotechnic mechanisms, pyrotechnic shock tests were conducted on three configurations: pin-pullers on an orthogonal double Hopkinson bar arrangement, pin-pullers on a mock-up of the HALOE (Halogen Occultation Experiment) structure, and a section of separation joint on a single Hopkinson bar. Strains and accelerations were measured. The strains were converted to output stresses, forces and moments. Acceleration shock response spectra are presented for both acceleration- and force-time signals. The devices were attached to the Hopkinson bars with adaptors, which are typical of attachments used in practice. In order to predict the effect of the adaptors, finite element models of the adaptor-bar combinations were analyzed and results are presented with regard to grid size, time interval, and frequency range required to predict the response to pulses of 10 and 100 microsecond duration.
Aircraft and ground vehicle friction data collected during the Joint FAA/NASA Runway Friction Program under winter runway conditions are discussed and test results are summarized. The relationship between the different ground vehicle friction measurements obtained on compacted snow- and ice-covered conditions is defined together with the correlation to aircraft tire friction performance under similar runway conditions.
Problems of joining involving structural components made of aluminum alloys with boron-fiber reinforcements are discussed, giving attention to a diffusion-welding process. The tension characteristics and weight factors in the case of various types of welded joints are considered. Diffusion-welding equipment used in the experimental investigation is described. The strength characteristics obtained in various cases of weld and component design are examined, taking into account static and dynamic stresses.
An efficient Navier-Stokes analysis was successfully applied to simulate the complex flow field in the vicinity of a slot in a solid rocket motor with segment joints. The capability of the computer code to resolve the flow near solid surfaces without using a wall function assumption was demonstrated. In view of the complex nature of the flow field in the vicinity of the slot, this approach is considered essential. The results obtained from these calculations provide valuable design information, which would otherwise be extremely difficult to obtain. The results of the axisymmetric calculations indicate the presence of a region of reversed axial flow at the aft-edge of the slot and show the over-pressure in the slot to be only about 10 psi. The results of the asymmetric calculations indicate that a pressure asymmetry more than two diameters downstream of the slot has no noticeable effect on the flow field in the slot. They also indicate that the circumferential pressure differential caused in the slot due to failure of a 15 deg section of the castable inhibitor will be approximately 1 psi.
The linearization method presented for calculating the transient responses of nonlinear systems due to initial disturbances is an extension of the 'describing function' approach, in which the system's steady-state response is calculated by representing such nonlinear elements as space structure joints with impedances that are functions of response amplitude. It is shown that, for the transient case, the steady-state impedances can be averaged over the range of responses in order to furnish equivalent values of stiffness and damping; these, for a given set of initial displacements, may be treated as constant during calculations of system response.
This paper presents the results of a joint NOAA and NASA sounder simulation study in which the accuracies of atmospheric temperature profiles and surface skin temperature measuremnents retrieved from two sounders were compared: (1) the currently used IR temperature sounder HIRS2 (High-resolution Infrared Radiation Sounder 2); and (2) the recently proposed high-spectral-resolution IR sounder AMTS (Advanced Moisture and Temperature Sounder). Simulations were conducted for both clear and partial cloud conditions. Data were analyzed at NASA using a physical inversion technique and at NOAA using a statistical technique. Results show significant improvement of AMTS compared to HIRS2 for both clear and cloudy conditions. The improvements are indicated by both methods of data analysis, but the physical retrievals outperform the statistical retrievals.
The performance limitations of joint-variable-feedback-controlled manipulators due to manipulator flexibility are studied in fine and gross motions. A finite-dimensional time-domain manipulator model is used in the study. Fine-motion analysis results agree very well with the previously reported results of infinite-dimensional frequency-domain models. The limitations of a class of adaptive controllers in high-speed gross motion control are studied. Manipulation speeds are quantified as low, medium, or high with reference to the arm flexibility and dynamic nonlinearities.
With the development of satellite altimetry, it is possible to infer the geostrophic velocity of the surface ocean currents, if the geoid and the position of the satellite are known accurately. Errors in current geoid models and orbit computations, both due primarily to errors in the earth's gravity field model, have limited the use of altimeter data for this purpose. The objective of this investigation is to demonstrate that altimeter data can be used in a joint solution to simultaneously estimate the quasi-stationary sea surface topography, zeta, and the model for the gravity field. Satellite tracking data from twelve satellites were used along with Seasat altimeter data for the solution. The estimated model of zeta compares well at long wavelengths with the hydrographic model of zeta. Covariance analysis indicates that the geoid is separable from zeta up to degree 9, at which point geoid error is comparable to the signal of zeta.
Current designs, a first generation intended for robotic assembly, have given priority to the ease and certainty of the assembly process under less than ideal conditions with a minimum of sensory feedback. As a consequence they are either heavy or expensive and all exhibit a relatively low packaging density. Low packaging density is caused by extensive scars applied to the node, increasing its envelope diameter by as much as 150 percent. Strut envelopes are violated to a lessor extent with diameters increased by 25 percent or more. This smaller percentage is still a significant problem owing to a much higher fraction of the packaged volume represented by struts. As structures in space become larger, packaging density becomes an important consideration. The objective is to develop end-effector-joint conjugates that do not violate the envelopes of a 2.5 inch diameter node or a 1.0 inch diameter strut.
A general control scheme to control flexible arms with friction in the joints is proposed in this paper. This scheme presents the advantage of being robust in the sense that it minimizes the effects of the Coulomb friction existing in the motor and the effects of changes in the dynamic friction coefficient. A justification of the robustness properties of the scheme is given in terms of the sensitivity analysis.