Fuzzy controller implementations with fewer than ten transistors?
Evolutionary algorithms offer good promise for automated design of analog circuits as well as for adaptation and automatic reconfiguration of programmable devices.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Evolutionary algorithms offer good promise for automated design of analog circuits as well as for adaptation and automatic reconfiguration of programmable devices.
We present VLBI Space Observatory Programme (VSOP) observations of the gamma-ray blazar 3C 279 at 1.6 and 5 GHz made on 1998 January 9-10 with the HALCA satellite and ground arrays including the Very Long Baseline Array (VLBA).
This paper describes the design of a reconfigurable chip programmable at the transistor level and oriented to the implementation of Evolvable Hardware (EHW) experiements.
The worst case timing margin of a synchronous design implemented with a field-programmable gate array (FPGA) is easy to perform using available FPGA design tools. However, it may be difficult to impossible to verify that worst case timing requirements are met for complex asynchronous logic design.
A complete programmable digital camera-on-a-chip based on low power active pixel sensor technology is implemented as a single CMOS integrated circuit.
This paper describes a working flight computer Multichip Module developed jointly by JPL and TRW under their respective research programs in a collaborative fashion. The MCM is fabricated by nCHIP and is packaged within a 2 by 4 inch Al package from Coors. This flight computer module is one of three modules under development by NASA's Advanced Flight Computer (AFC) program. Further development of the Mass Memory and the programmable I/O MCM modules will follow. The three building block modules will then be stacked into a 3D MCM configuration. The mass and volume of the flight computer MCM achieved at 89 grams and 1.5 cubic inches respectively, represent a major enabling technology for future deep space as well as commercial remote sensing applications.
This paper overviews Evolvable Hardware (EHW) technology, examining its potential for enhancing survivability and flexibility of future space systems. EHW refers to selfconfiguration of electronic hardware by evolutionary/genetic search mechanisms. Evolvable Hardware can maintain existing functionality in the presence of faults and degradations due to aging, temperature and radiation. It can also configure itself for new functionality when required for mission changes or encountered opportunities. The paper illustrates hardware evolution in silicon using a JPL-designed programmable device reconfigurable at transistor level as the platform and a genetic algorithm running on a DSP as the reconfiguration mechanism. Rapid reconfiguration allows convergence to circuit solutions in the order of seconds. The experiments demonstrate functional recovery from faults as well as from degradation at extreme temperatures indicating the possibility of expanding the operational range of extreme electronics through evolved circuit solutions.
The conventional wisdom in the scientific computing community is that the best way to solve large-scale numerically intensive scientific problems on today's parallel MIMD computers is to use Fortran or C programmed in a data-parallel style using low-level message-passing primitives. This approach inevitably leads to nonportable codes, extensive development time, and restricts parallel programming to the domain of the expert programmer. We believe that these problems are not inherent to parallel computing but are the result of the tools used. We will show that comparable performance can be achieved with little effort if better tools that present higher level abstractions are used.
This paper describes the design of Chapel, the Cascade High Productivity Language, which is being developed in the DARPA-funded HPCS project Cascade led by Cray Inc. Chapel pushes the state-of-the-art in languages for HEC system programming by focusing on productivity, in particular by combining the goal of highest possible object code performance with that of programmability offered by a high-level user interface.
Not until recently, Xilinx has developed a new field programmable gate array (FPGA) device family, Virtex-I1 Pro. In this single device, not only dies it have density logic cells (3K to125K), gigabit connectivity, on chip memory, digital clock management, but also it can have up to four IBM PowerPC 405 Processor hard cores, running up to 400MHz and 633 Mbps. To utilize this cutting edge device in space applications, a few Single Event Upset (SEU) mitigation techniques need to be implemented to a design for the device. At Jet Propulsion Laboratory (JPL), we have successfully demonstrated the feasibility of running multiple processors running in a lock step fashion to accomplish SEU mitigation and fault tolerance.
We are developing an Arbitrary Waveform Generator (AWG) to provide enhanced capability for radar applications. The current design will accommodate two waveform generators on a single unit for dual frequency operation. The basic architecture of this unit employs a Field Programmable Gate Array (FPGA) and a high speed and high precision Digital to Analog Converter (DAC) for direct digital synthesis. This AWG will be capable of up to 450 MHz bandwidth with ability for frequency notching. Phase fidelity of less than 1.2(sup o) deviation RMS is also achievable. This AWG operates with lower power consumption as compared with other waveform generators, which is advantageous for future spaceborne applications. This will enable radars to return higher precision data, to be reduced in complexity, and to operate in any band without interfering with dedicated bandwidths.
The predominant failure mode in an ultra longlife system is the wear-out of components. In order to survive long duration missions, current fault tolerant design techniques would require excessive number of redundant components. This paper describes a more efficient fault tolerant avionics system architecture that requires much less redundant components. This architecture employs generic function blocks that can be programmed to replace a wide variety of components in-flight. Hence, each individual generic block is essentially equivalent to almost an entire redundant string of components in the conventional approach. In that way, the ultra long-life system can achieve much higher level of reliability while carrying much less components. On the other hand, due to the programmability of the generic redundant blocks, the physical location of a specific component might not be pre-determined. Therefore, wireless interconnection is employed to provide the necessary flexibility in connectivity. A testbed of this architecture is being developed at the Jet Propulsion Laboratory.
We have developed an instrument concept that combines a conventional nadir altimeter with a radar interferometer to meet the above requirements. In this paper, we describe the overall mission concept and the interferometric radar design. We also describe several new technology developments that facilitate the inclusion of this instrument on a small, inexpensive spacecraft bus. Those include ultra-light, deployable reflectarray antennas for the radar interferometer; a novel five frequency feed horn for the radiometer and altimeter; a lightweight, low power integrated three frequency radiometer; and a field programmable gate array-based onboard data processor. Finally, we discuss recent algorithm developments for the onboard date processing, and present the expected instatements performance improvements over previously reported results.
We propose a tuning method for MEMS gyroscopes based on evolutionary computation to efficiently increase the sensitivity of MEMS gyroscopes through tuning. The tuning method was tested for the second generation JPL/Boeing Post-resonator MEMS gyroscope using the measurement of the frequency response of the MEMS device in open-loop operation. We also report on the development of a hardware platform for integrated tuning and closed loop operation of MEMS gyroscopes. The control of this device is implemented through a digital design on a Field Programmable Gate Array (FPGA). The hardware platform easily transitions to an embedded solution that allows for the miniaturization of the system to a single chip.
A magnetic field response recorder was developed to facilitate a measurement acquisition method that uses magnetic fields to power and to interrogate all sensors. Sensors are designed as electrically passive inductive-capacitive or passive inductive-capacitive-resistive circuits that produce magnetic field responses when electrically activated by oscillating magnetic fields. When electrically activated, the sensor's magnetic field response attributes (frequency, amplitude and bandwidth) correspond to the one or more physical states that each sensor measures. The response recorder makes it possible to simultaneously measure two unrelated physical properties using this class of sensors. The recorder is programmable allowing it to analyze one or more response attributes simultaneously. A single sensor design will be used to demonstrate that the acquisition method and the sensor example can be used to for all phases of a component's life from manufacturing to damage that can destroy it.
The TSPT (Time Series Product Tool) software was custom-designed for NASA to rapidly create and display single-band and band-combination time series, such as NDVI (Normalized Difference Vegetation Index) images, for wide-area crop surveillance and for other time-critical applications. The TSPT, developed in MATLAB, allows users to create and display various MODIS (Moderate Resolution Imaging Spectroradiometer) or simulated VIIRS (Visible/Infrared Imager Radiometer Suite) products as single images, as time series plots at a selected location, or as temporally processed image videos. Manually creating these types of products is extremely labor intensive; however, the TSPT development tool makes the process simplified and efficient. MODIS is ideal for monitoring large crop areas because of its wide swath (2330 km), its relatively small ground sample distance (250 m), and its high temporal revisit time (twice daily). Furthermore, because MODIS imagery is acquired daily, rapid changes in vegetative health can potentially be detected. The new TSPT technology provides users with the ability to temporally process high-revisit-rate satellite imagery, such as that acquired from MODIS and from its successor, the VIIRS. The TSPT features the important capability of fusing data from both MODIS instruments onboard the Terra and Aqua satellites, which drastically improves cloud statistics. With the TSPT, MODIS metadata is used to find and optionally remove bad and suspect data. Noise removal and temporal processing techniques allow users to create low-noise time series plots and image videos and to select settings and thresholds that tailor particular output products. The TSPT GUI (graphical user interface) provides an interactive environment for crafting what-if scenarios by enabling a user to repeat product generation using different settings and thresholds. The TSPT Application Programming Interface provides more fine-tuned control of product generation, allowing experienced programmers to bypass the GUI and to create more user-specific output products, such as comparison time plots or images. This type of time series analysis tool for remotely sensed imagery could be the basis of a large-area vegetation surveillance system. The TSPT has been used to generate NDVI time series over growing seasons in California and Argentina and for hurricane events, such as Hurricane Katrina.
In the frame of the International Space Station (ISS) Program cooperation, in 1998, the European Space Agency (ESA) approached the National Aeronautics and Space Administration (NASA) with the unique concept of a Payload Safety Review Panel (PSRP) "franchise" based at the European Space Technology Center (ESTEC), where the panel would be capable of autonomously reviewing flight hardware for safety. This paper will recount the course of an ambitious idea as it progressed into a fully functional reality. It will show how a panel initially conceived at NASA to serve a national programme has evolved into an international safety cooperation asset. The PSRP established at NASA began reviewing ISS payloads approximately in late 1994 or early 1995 as an expansion of the pre-existing Shuttle Program PSRP. This paper briefly describes the fundamental Shuttle safety process and the establishment of the safety requirements for payloads intending to use the Space Transportation System and International Space Station (ISS). The paper will also offer some historical statistics about the experiments that completed the payload safety process for Shuttle and ISS. The paper 1 then presents the background of ISS agreements and international treaties that had to be taken into account when establishing the ESA PSRP. The detailed franchising model will be expounded upon, followed by an outline of the cooperation charter approved by the NASA Associate Administrator, Office of Space Flight, and ESA Director of Manned Spaceflight and Microgravity. The resulting ESA PSRP implementation and its success statistics to date will then be addressed. Additionally the paper presents the ongoing developments with the Japan Aerospace Exploration Agency. The discussion will conclude with ideas for future developments, such to achieve a fully integrated international system of payload safety panels for ISS.
Aluminium foils exposed to impact during the passage of the Stardust spacecraft through the coma of comet Wild 2 have preserved a record of a wide range of dust particle sizes. The encounter velocity and dust incidence direction are well constrained and can be simulated by laboratory shots. A crater size calibration programme based upon buckshot firings of tightly constrained sizes (monodispersive) of glass, polymer and metal beads has yielded a suite of scaling factors for interpretation of the original impacting grain dimensions. We have now extended our study to include recognition of particle density for better matching of crater to impactor diameter. A novel application of stereometric crater shape measurement, using paired scanning electron microscope (SEM) images has shown that impactors of differing density yield different crater depth/diameter ratios. Comparison of the three-dimensional gross morphology of our experimental craters with those from Stardust reveals that most of the larger Stardust impacts were produced by grains of low internal porosity.