Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermomechanical properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Iron-Catalyzed Cross-[2 + 2] Cycloaddition of Butadiene and α,ω-Dienes for Ductile and Chemically Recyclable Poly(oligocyclobutanes)

Poly(divinyloligocyclobutanes) (pDVOCBs) are a distinct class of butadiene-derived, chemically recyclable polyolefins prepared from iron-catalyzed [2 + 2] cycloaddition followed by ruthenium-catalyzed ADMET polymerization. These polymers are highly crystalline, with high melting temperatures and unique rotator phases. The high degree of crystallinity in these materials not only leads to high stiffness over a broad temperature range but also results in brittle failure for polymers of modest molecular weights. Iron-catalyzed cross-[2 + 2] cycloaddition of butadiene and α,ω-dienes was accomplished, where the number of methylene units between the four-membered rings was systematically varied. Subsequent ADMET polymerization of the resulting telechelic oligomers provided a new class of chemically recyclable polyolefins that exhibit distinct thermomechanical properties. Specifically, methylene units induce changes in crystallinity that, in combination with the increased molecular weight, favored the formation of stable necks upon tensile deformation, with ∼10× enhanced ductility and improved toughness compared to pDVOCB. Through combined experimental and computational studies, the effects of methylene spacers on the crystal-to-rotator transition of the cyclobutane polymers were established. Ultimately, these methylene-modified cyclobutane polymers expand the range of properties and potential applications of this class of recyclable polyolefins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Circular olefin copolymers made de novo from ethylene and α-olefins

Ethylene/α-olefin copolymers are produced in huge scale and widely used, but their after-use disposal has caused plastic pollution problems. Their chemical inertness made chemical re/upcycling difficult. Ideally, PE materials should be made de novo to have a circular closed-loop lifecycle. However, synthesis of circular ethylene/α-olefin copolymers, including high-volume, linear low-density PE as well as high-value olefin elastomers and block copolymers, presents a particular challenge due to difficulties in introducing branches while simultaneously installing chemical recyclability and directly using industrial ethylene and α-olefin feedstocks. Here we show that coupling of industrial coordination copolymerization of ethylene and α-olefins with a designed functionalized chain-transfer agent, followed by modular assembly of the resulting AB telechelic polyolefin building blocks by polycondensation, affords a series of ester-linked PE-based copolymers. These new materials not only retain thermomechanical properties of PE-based materials but also exhibit full chemical circularity via simple transesterification and markedly enhanced adhesion to polar surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Machine learned interatomic potential for dispersion strengthened plasma facing components

Tungsten (W) is a material of choice for the divertor material due to its high melting temperature, thermal conductivity, and sputtering threshold. However, W has a very high brittle-to-ductile transition temperature, and at fusion reactor temperatures (≥1000 K), it may undergo recrystallization and grain growth. Dispersion-strengthening W with zirconium carbide (ZrC) can improve ductility and limit grain growth, but much of the effects of the dispersoids on microstructural evolution and thermomechanical properties at high temperatures are still unknown. We present a machine learned Spectral Neighbor Analysis Potential for W–ZrC that can now be used to study these materials. In order to construct a potential suitable for large-scale atomistic simulations at fusion reactor temperatures, it is necessary to train on ab initio data generated for a diverse set of structures, chemical environments, and temperatures. Further accuracy and stability tests of the potential were achieved using objective functions for both material properties and high temperature stability. Additionally, validation of lattice parameters, surface energies, bulk moduli, and thermal expansion is confirmed on the optimized potential. Tensile tests of W/ZrC bicrystals show that although the W(110)–ZrC(111) C-terminated bicrystal has the highest ultimate tensile strength (UTS) at room temperature, observed strength decreases with increasing temperature. At 2500 K, the terminating C layer diffuses into the W, resulting in a weaker W–Zr interface. Meanwhile, the W(110)–ZrC(111) Zr-terminated bicrystal has the highest UTS at 2500 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Temperature effects of ion irradiation on the nanostructural features in ductile-phase-toughened tungsten composites

Ductile-phase toughened tungsten (DPT W) composites have emerged as promising candidates for load-bearing components behind the plasma-facing tungsten armor in fusion reactors due to their enhanced thermomechanical properties. This study focuses on a composite consisting of W particles embedded in a ductile NiFeW solution matrix, hot-rolled to a thickness reduction of 87% (87R DPT W). Sequential irradiations with Ni2+ and He+ ions were performed to identical doses and helium concentrations at room temperature (RT) and 1273 K. Irradiation at RT produced no discernible nanostructural features due to the immobility of mono-vacancies, whereas cavity formation was observed at 973 K. At 1273 K, the W phase exhibited larger cavities, reduced cavity number density, and lower volumetric swelling compared to 973 K. Notably, nanosized NiFeW precipitates formed within the W phase at 1273 K, a phenomenon absent at 973 K. A new phase of cubic (NiFe)6W6C was also observed at the interphase boundary. In contrast, the NiFeW matrix showed no nanostructural changes at 1273 K, likely due to cavity dissociation. Separate irradiations at 1273 K indicated that Ni2+ ions induced precipitate formation in the W phase, while He+ ions exclusively caused cavity formation. The microstructure of 87R DPT W irradiated at RT and subsequently annealed at 1273 K closely resembled that of material irradiated directly at 1273 K. Like oxide-dispersion-strengthened steels, the observed nanoparticle-embedded W can inhibit dislocation propagation, potentially delaying the ductile-to-brittle transition temperature. These findings highlight the potential of NiFeW nanoparticle-reinforced W composites as irradiation-resistant materials for fusion reactors.

Jiang, Weilin (ORCID:0000000183028313)↗
DOE OSTI2021

Design and Analysis of an Advanced Three-Point Bend Test Approach for Miniature Irradiated Disk Specimens

Candidate tungsten armor materials in a magnetic confinement fusion device must be able to withstand thermal variation that leads to internal stresses caused by the impinging heat load. In addition, the thermomechanical properties of these materials are degraded by irradiation-induced defect accumulation. Fission reactor–based irradiation data are used to predict the fusion neutron damage and property change. This study examines the motivation and design of a custom-designed three-point bend test for neutron-irradiated disk specimens that are 3 mm in diameter to be able to define the flexural strength of advanced tungsten materials, alloys, and composites—and to the extent that embrittlement occurs after neutron irradiation. The theory provided shows a calculation for the flexural deflection and shear deflection due to the small-geometry constraints. A finite element deformation analysis is performed to evaluate the mechanical stress field of disk bend specimens. The stress values above 80% of the maximum stress are concentrated in 2.4 mm of the 3.0-mm length of the centerline across the tungsten disk diameter. A bend test fixture has been designed and fabricated to enable testing of these specimens with precisely engineered tolerance and minimal machine compliance. This fixture will be able to be placed inside a universal testing frame at elevated temperatures for the mechanical property evaluation of future neutron-irradiated disk specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure-dependent rate theory model of defect segregation and phase stability in irradiated polycrystalline LiAlO 2

We report gamma lithium aluminate (LiAlO 2 ) is a breeder material for tritium and is one of key components in a tritium-producing burnable absorber rod (TPBAR). Dissolution and precipitation of second phases such as LiAl 5 O 8 and voids are observed in irradiated LiAlO 2 . Such microstructure changes cause the degradation of thermomechanical properties of LiAlO 2 and affect tritium retention and release kinetics, and hence, the TPBAR performance. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed for investigating the accumulation of species and phase stability in polycrystalline LiAlO 2 structures under irradiation. Three sublattices (i.e. [Li, Al, V] I [O, V o ] II [Li i , Al i , O i , V i ] III ), and concentrations of six diffusive species (i.e. Li; vacancy of Li or Al at [Li, Al, V] I sublattice, O vacancy at [O, V o ] II sublattice, and Li, Al and O interstitials at [Li i , Al i , O i , V i ] III interstitial sublattices; are used to describe spatial and temporal distributions of defects and chemistry. Microstructure-dependent thermodynamic and kinetic properties including the generation, reaction, and chemical potentials of defects and defect mobility are taken into account in the model. The parametric studies demonstrated the capability of the developed RIS model to assess the effect of thermodynamic and kinetic properties of defects on the segregation and depletion of species in polycrystalline structures and to explain the phase stability observed in irradiated LiAlO 2 samples. The developed RIS model will be extended to study the precipitation of LiAl 5 O 8 and voids and tritium retention by integrating the phase-field method.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Inelastic neutron spectra of polyacrylonitrile-based carbon fibers

We present the vibrational spectra of polyacrylonitrile-based carbon fibers collected using inelastic neutron scattering. We ascertain the behavior of a broad range of vibrational spectra that are optically silent, and demonstrate a direct connection between these modes and thermomechanical properties of the fibers. We show directionally dependent coupling of hydrogen in the carbon fiber matrix, which is directly linked to mechanical properties. Further, we show hydrogen preferentially couples to the midband of the vibrational spectrum, and that there are higher overall mode populations in the traditional Raman D–G intervalley region, suggesting involvement of these modes in tensile strength reduction and transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure and bonding between calcium aluminate cement‐containing gahnite–alumina matrix and refractory aggregates

Calcium aluminate cement enhances the thermomechanical properties of refractory castables through the formation of acicular calcium hexaluminate (CaO·6Al 2 O 3 ), Ca 2 Mg 2 Al 28 O 46 (CAM-I), and CaMg 2 Al 16 O 27 (CAM-II) phases in MgO- or MgAl 2 O 4 -containing castables. The compatibility of CA 6 with gahnite (ZnAl 2 O 4 ), and acicular Ca 2 Zn 2 Al 28 O 46 (CAZ-I) and CaZn 2 Al 16 O 27 (CAZ-II) phases formation have been previously reported. Here, in this work, the interaction between a CAC binder containing ZnAl 2 O 4 -Al 2 O 3 matrix with commonly used refractory aggregates such as tabular alumina (TA), alumina-rich (AR90, AR78) and stoichiometric (SM72) MgAl 2 O 4 spinels, and fused and dead-burned magnesia (FM, DBM, respectively) were investigated at 1650°C for 5 h. Microstructural analysis, using digital microscopy, scanning electron microscopy, and energy dispersive spectroscopy, revealed the formation of acicular CaZn 0.18 Al 11.82 O 18.91 , CAZ-I and CAZ-II grains, and strong interfacial bonding between the matrix and TA and spinel aggregates. FM and DBM were found to debond from the matrix. Thick interface layers were observed between the matrix and all the aggregates but TA. Null hypothesis significance testing (NHST) shows that the difference in the number of acicular grains between the interface zone and the bulk matrix (Z) is statistically significant for AR90/Z, SM72/Z, FM/Z, and DBM/Z interfaces, but not significant for TA/Z and AR78/Z. The role of the aggregates’ chemistry on the interfacial bonding and microstructure evolution is discussed.

Ramteke, Rajat Durgesh [Univ. of Alabama, Birmingh↗
DOE OSTI2024

A Techno-Economic Analysis of a 50MWth Light-Trapping Cavity-Planar Solar Receiver Tower Capital Expenditures and its Cost Mitigation Strategies

To maximize thermal efficiency, the National Renewable Energy Laboratory (NREL) has proposed a light-trapping cavity-planar receiver design intended to capture energy from reradiating surfaces. This system implements a macroscale light trapping mechanism induced by panels with triangular channels, this mechanism allows for elevated temperatures on the receiver panels and in turn the temperature of the HTF; using this design coupled with the implementation of a fluidized particle flow as the HTF, it can be expected for some components to reach a peak working temperature of nearly 1000 degrees C cyclically throughout each day-night cycle. While these temperatures correlate to higher efficiency of the CSP tower they also demand intense thermomechanical properties from the materials used to make the receiver panels. In this analysis, we will list our assumptions to provide clarity on the significance of our calculation. This cost analysis will be conducted using a combination of both case study data and surveying industry to determine costs that are relevant to the current market trends. This analysis represents an early attempt to establish the Capital Expenditures required for a CSP tower of such design to determine the feasibility of implementing such a system in the industry.

concentrated solar power (CSP)↗
DOE OSTI2020

Joining Techniques for Novel Metal Polymer Hybrid Heat Exchangers

In the United States, over 50% of the unrecovered energy from industrial processes is in the form of low-grade heat (< 220°C). Materials and maintenance costs of common heat exchangers are typically too high to justify their usage. Polymers, though more affordable, are usually unsuitable for HX applications due to their low thermal conductivity (~0.2 W/mK). Here, we show that metal-polymer hybrids may be attractive from both performance and cost perspectives. The use of polymers further increases the resistance to corrosion by sulfuric and carbonic acids often present in flue gases. An ongoing work explores different configurations of layered polyimide-copper macroscale hybrids for heat exchanger applications using numerical simulations. This paper explores a manufacturing pathway for producing such layered hybrid tubes that involves directly rolling and bonding tapes made of polymer and copper foil into tubes. A critical problem in the fabrication process is the bonding of metal and polymers. We explore approaches involving adhesives (epoxy, acrylic and silicone) for metal/polymer interfaces and direct welding (ultrasonic) for metal/metal interfaces that can be integrated into the manufacturing process. We report characterizations of the thermomechanical properties of these joining processes. This work paves the way for realizing cost-effective manufacturing of heat exchangers for low grade waste heat recovery.

Kuntumalla, Gowtham↗
DOE OSTI2022

Characterization of Refractory Alloys Produced by Laser Additive Manufacturing

Refractory alloys often possess superior thermomechanical properties compared to conventional materials, such as steels, Ni-based superalloys, and Ti alloys, especially in high-temperature environments. While these materials promise to revolutionize numerous industries, significant hurdles remain for insertion into applications due to an incomplete understanding of structure-property relationships and conventional processing challenges. We explore laser-based additive manufacturing (AM) to construct refractory alloys consisting of combinations of Mo, Nb, Ta, and Ti with systematically increasing compositional complexity. Microstructure, composition, and hardness of the AM-processed alloys were characterized. Results are discussed in the context of pairing additive manufacturing with refractory metals to enable next-generation alloys.

Kustas, Andrew B.↗
DOE OSTI2024

Epoxy resin reinforced with carbonized chicken feathers: An innovative composite material with sustainable potentials

Here, this article explores a novel method for enhancing the mechanical properties of epoxy resin composites by incorporating carbonized chicken feathers as a filler material. The fabrication process involves carbonizing chicken feathers at 600°C and incorporating 5-10 wt% of the fillers into an epoxy matrix. The composites showed enhanced mechanical properties and samples containing 10 wt% filler exhibit the best properties. The performance corresponds to 49% increase in tensile strength, 16% rise in Young’s modulus, 40% improvement in flexural modulus, and 57% in flexural strength. X-ray diffraction and scanning electron microscopy with energy dispersive spectroscopy were employed to characterize the filler. This characterization provides valuable insights into the structure and chemical composition of the pulverized carbonized chicken feathers that contributed to the attained improvement in composites’ properties. Microstructural examination of the developed composite under scanning electron microscope also provides insights into matrix-filler interface and dispersion of the fillers within the composite matrix. The study not only highlights the unique combination of carbonized feathers’ inherent strength and compatibility with the epoxy matrix but also underscores the eco-friendly nature of utilizing agricultural waste. The findings suggest promising applications in industries demanding lightweight, high-strength materials, which can contribute to sustainable engineering solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-temperature superelasticity in NiTiPt and NiTiPd shape memory alloys

Alloying NiTi shape memory alloys with sufficient Pt and Pd at the expense of Ni has been shown to increase transformation temperatures well above those possible with the binary composition, enabling consideration of a new class of high-temperature mechanical sensors and actuators. To achieve shape memory behavior at temperatures greater than 200 °C, previous studies of NiTiPt and NiTiPd compositions have focused primarily on alloys with greater than 16 at.% Pt and 25 at.% Pd. While generally not the focus, none of these previous studies demonstrated superelastic behavior at high temperatures. In an effort to identify alloys that transform to austenite at approximately 200 °C and exhibit superelastic behavior with recoverable strains greater than 2%, a series of Ti-rich NiTiPt ternary alloys with 15.5–16.5 at.% Pt, and Ti-rich NiTiPd ternary alloys with 25–26 at.% Pd have been targeted. The polycrystalline alloys were processed via arc melting followed by homogenization heat treatment. Thermomechanical properties were measured using electro-discharge machined tension test coupons and a miniature load frame equipped with a clamshell furnace. Ultimately, superelasticity in uniaxial tension with clear plateau regions was demonstrated and characterized in these alloys at temperatures between 219 °C and 270 °C.

Massad, Jordan E.↗
DOE OSTI2023

Digital Light Processing (DLP): 3D printing of polymer-based graphene oxide nanocomposites—Efficient antimicrobial material for biomedical devices

Bacterial infections are one of the major causes of surgical implant inefficiency and failure. Herein, we present a Nanocomposite (NC) produced by the addition of Poly(N-vinyl carbazole)-Graphene Oxide dispersion (PVK-GO) as a nanofiller to a commercial photopolymer acrylate resin and 3D printed as coatings via the Digital Light Processing technique. Characterization and bioassay results against Escherichia coli and Staphylococcus aureus confirmed the elevated thermomechanical properties and efficient antibacterial activity of the printed NC-based coatings. In conclusion, the present study demonstrates the fabrication and optimization of a PVK-GO-based NC and its potential utilization as a 3D-printable material for biomedical applications.

2D materials↗
DOE OSTI2020

Irradiation enhanced diffusion and diffusional creep in U₃Si₂

U₃Si₂ is a candidate as an advanced fuel for light water reactors (LWRs). Compared to UO₂, there are significant data gaps for the thermophysical and thermomechanical properties of U₃Si₂. Atomic scale simulations can help fill in those gaps, while also providing a more mechanistic understanding of the material properties. Creep is an important property for fuel performance as it influences the pellet-cladding gap, which in turn affects the temperature of the fuel (a key parameter in many other aspects of fuel behavior). In this work, we employed a DFT-informed cluster dynamics framework to predict point defect concentrations in U₃Si₂. The concentrations, diffusivities, and volumes of these defects were used to develop a diffusional creep model based on bulk (Nabarro-Herring) and grain boundary (Coble) diffusion processes. It was found that irradiation enhanced Nabarro-Herring creep is dominant at low temperatures, while Coble creep dominates for high temperatures. The model compares well against available experimental data and has been implemented in BISON. A demonstration case using simple power profiles has been carried out, showing that negligible creep occurs due to the low temperatures experienced by U₃Si₂, a consequence of its high thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

X-Ray Scattering Data Processing and Analysis

Semicrystalline polymers have a degree of crystallinity that depends on chain structure and crystallization conditions. Thermomechanical properties are influenced by the degree of crystallinity and crystalline morphology. A common method used to understand crystalline content, crystal and amorphous layer thickness, and layer thickness distributions, is X-ray scattering (XS). This report uses XS to first investigate crystalline orientation in high density polyethylene (HDPE) samples. Then, a single orientation is analyzed via XS in a temperature study to investigate crystalline behavior under changing temperatures. Lastly, block copolymer filaments extruded at varying speeds are analyzed. The X-ray data are used to gain a baseline understanding of crystalline behavior in these unique filaments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Scalable, Infiltration-Free Ceramic Matrix Composite Manufacturing for Molten Salt Receiver (SIF-CMC)

Ceramic Matrix Composite (CMC) with high thermomechanical properties is a promising material class for Concentrated Solar Power but current use is limited by a long and tedious manufacturing process with high costs and poor scalability. SIF-CMC provides a novel way to simplify the manufacturing process by dramatically increasing the char yield of the matrix from polymer to ceramic, which makes the CMC affordable and scalable.

Wei, Junhua↗