Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plasma material interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Testing of spark plasma sintered porous tungsten under neon glow discharge cleaning conditions in LTX-β

This paper demonstrates that tungsten (W) based powder reconstituted Plasma Facing Components (PFCs) can be treated in situ in a fusion reactor to remove W oxide and carbon (C) contamination. Doing so should ease the challenge of using these materials in a Capillary Porous System (CPS) with lithium (Li) by enabling better wetting and less contamination of the Li by the underlying CPS. Most powder reconstituted materials including 3D printed and sintered PFCs suffer from a high surface contamination from oxides and surface C, which complicates their use with liquid Li, a primary PFC candidate. Spark plasma sintered porous W samples were fabricated to be used as a CPS with liquid Li. The samples were characterized in terms of morphology and surface chemistry. Analysis confirms a high C and oxygen (O) contamination. We present the results of exposing this type of CPS to Glow Discharge Cleaning (GDC) cycles in the Lithium Tokamak Experiment-β (LTX-β). The sample was exposed to neon (Ne) GDC in the midplane of the low-field side of LTX-β and analyzed in vacuo with Temperature Programmed Desorption (TPD) and Secondary Ion Mass Spectrometry (SIMS) to investigate the effects the Ne GDC had on the chemical composition of the sample. The combination of Ne GDC with rapid heating as done in TPD was successful in reducing the W oxides and removing the C contamination.

Capillary porous system↗
DOE OSTI2020

Recent progress in microscale modeling of RF sheaths

The microscale properties of RF sheaths in the ion cyclotron range of frequencies (ICRF) are investigated by means of analytical theory, nonlinear fluid and particle-in-cell (PIC) code modeling. Previous work that parametrized RF sheath properties, specifically the RF sheath impedance and the rectified (DC) sheath potential, is generalized to include the effect of net DC current flow through the sheath. Analytical results are presented in the low frequency limit where the displacement current is negligible, and tested against results from a fluid numerical model. Here, it is shown that when the sheath draws DC electron current, the voltage rectification is reduced from the zero current case, and the electron admittance is increased. In separate but related work on the microscale model, selected cases have been simulated with PIC codes to validate, further illuminate and extend fluid model results and their parametrizations. Quantitative agreement in trends for voltage rectification and sheath admittance vs. RF driving voltage is found.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

More about hot electrons between cold walls

This paper adds new findings to the recently described hampering of electron cooling by electron trapping in a developing electrostatic potential well between the two cold walls. We show that the self-consistent process of the potential well formation and electron trapping is tractable analytically when the end walls reflect most of the incoming electrons. For immobile ions, this process creates a steady-state that retains a significant fraction of the initial electron kinetic energy. Here, we also describe the subsequent slow decay of the system due to ion motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Modeling transient edge plasma transport with dynamic recycling

The work presents numerical simulation studies of the role that dynamic plasma recycling on the main wall and divertor target surfaces plays in transient edge plasma transport phenomena, such as edge localized modes (ELMs). The studies are performed by coupling the edge plasma transport code UEDGE [Rognlien et al., J. Nucl. Mater. 196–198, 347 (1992)] and the wall reaction–diffusion transport code FACE [Smirnov et al., Fusion Sci. Technol. 71, 75 (2017)]. The two-dimensional, time-dependent, two-way coupling of the codes, in a realistic tokamak geometry, is accomplished using the Integrated Plasma Simulator framework [Elwasif et al., in 18th Euromicro Conference on Parallel, Distributed and Network-Based Processing (PDP 2010), Pisa, Italy (IEEE, 2010), pp. 419–427] for all modeled material plasma boundaries. The simulations show that dynamic plasma recycling has substantially different characteristics on the main wall and on the divertor plates. It is demonstrated that during an ELM cycle the outer wall can dynamically absorb and release a number of particles comparable to that expelled by the ELM from the core plasma, by far exceeding the dynamic retention capacity of the divertor surfaces. The resulting evolution of the edge and divertor plasma conditions during an ELM cycle is analyzed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D

ITER-grade tungsten and dispersoid-strengthened tungsten samples with the top surface angled at ~15° towards the incident plasma flux were exposed to 9 H-mode discharges with edge-localized modes (ELMs) in the lower divertor of DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Surface damage included cracking and flaking of material on the two samples farthest away from the plasma strike point, and significant melting of the two samples closest to the strike point. Heat flux and thermal analysis tools new to DIII-D have been applied to better understand this material response and to help optimize the exposure conditions for future experiments. SMITER field-line tracing simulations based on IRTV data and EFIT equilibria estimate an average inter-ELM perpendicular heat flux, 𝑞⊥,𝑖nter−𝐸LM , on the angled surfaces of 10.1 – 19.6 MW/m² for a majority of the 9 discharges, increasing to 15.6 – 24.5 MW/m² for the single, higher-power shot where samples melted. Fast camera data showed shallow intra-ELM melting and re-solidification, which transitioned to bulk inter-ELM melting with melt motion in the 𝐽⃗ 𝑥 𝐵⃗ direction. About 50% of the protruding volume of the most affected sample was displaced via melt-motion. SIERRA thermal modeling software was able to reproduce an onset time of melting consistent with fast camera data and final sample conditions, within < 200 ms. Maximum surface temperatures of 3122 K and 2787 K are estimated for the samples farthest away from the strike point, while the closest samples achieve melting at 4067 ms and 4750 ms into the ~5000 ms plasma exposure. A +10% increase in both the SMITER 𝑞⊥,𝑖nter−𝐸LM calculations and the estimated ELM heat loads 𝑞⊥, 𝐸LM was required to achieve this result, which is within the uncertainty of the diagnostic data but likely accounts for non-ideal geometry effects plus other physics uncertainties not included in this first iteration of modeling. This work provided valuable estimates of the 3D temperature evolution to help better understand the observed surface morphology and internal recrystallization of samples, which are discussed in detail in a complementary manuscript [1]. Benchmarking efforts with more diagnosed DIII-D experiments are underway to further refine the SMITER and SIERRA models for DiMES. Future use of these tools will enable researchers to precisely target heat flux exposure conditions in DIII-D to test, but not exceed, the thermomechanical limitations of novel plasma-facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Predictive outlook for experiments resolving prompt vs local redeposition of high- Z materials in tokamaks

High-Z plasma facing components redeposit within the sheath through a combination of two distinct mechanisms: prompt (or geometric-driven) and local (or sheath-driven) redeposition. Experimental efforts are needed to determine the leading-order parameters influencing prompt-vs-local trade-off, which sets the fraction of material entering the scrape-off layer. In preparation for such experiments, leading-order parameters are isolated within the PYEAD-RustBCA-GITR coupled net erosion code using Sobol’ sensitivity analysis. Then, experiments resolving prompt-vs-local trade-off under variation of these leading-order parameters are proposed using an isotopic coupon design with multifaceted diagnostic coverage. The measurability of these experiments is evaluated using synthetic diagnostics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Material mixing during fuzz formation in W and Mo

Helium-induced fuzz formation in tungsten (W) and molybdenum (Mo) is investigated for a range of sample exposure temperatures from 838 K–1075 K (He fluence = 3.4 × 10 25 m -2 and ion energy <39 eV). Thin films of Mo deposited on W substrates show mixing of the film and substrate materials in the fuzz after He plasma exposure, including at 838 K (i.e. below the typical temperature range at which fuzz forms in pure W). Finally, the amount of material mixing increases with exposure temperature due to the increase in bubble size, and leads to significant accumulation of the substrate material at the fuzz surface at the highest temperature investigated, further supporting fuzz growth from the fiber tip outwards by material transport up the fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Micro-trench measurements of the net deposition of carbon impurity ions in the DIII-D divertor and the resulting suppression of surface erosion

In this work, we report carbon impurity ion incident angles and deposition rates, along with silicon erosion rates, from measurements of micro-engineered trenches on a silicon surface exposed to L-mode deuterium plasmas at the DIII-D divertor. Post exposure ex-situ analysis determined elemental maps and concentrations, carbon deposition thicknesses, and erosion of silicon surfaces. Carbon deposition profiles on the trench floor showed carbon ion shadowing that was consistent with ERO calculations of average carbon ion angle distributions (IADs) for both polar and azimuthal angles. Measured silicon net erosion rates negatively correlated with the deposited carbon concentration at different locations. Differential erosion of surfaces on two different ion-downstream trench slope structures suggested that carbon deposition rate is affected by the carbon ion incident angle and significantly suppressed the surface erosion. The results suggest the C impurity ion incident angles, determined by the IADs and surface morphology, strongly affect erosion rates as well as the main ion (D, T, He) incident angles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Understanding tungsten erosion during inter/intra-ELM periods in He-dominated JET-ILW plasmas

Tungsten erosion was quantified during inter/intra-ELM periods in He-dominated JET-ILW plasmas by optical emission spectroscopy. The intra-ELM tungsten sputtering in helium plasmas, which dominates the total W source, prevails by a factor of about 4 over inter-ELM sputtering in the investigated ELM frequency range from 90 Hz–120 Hz. He ions are mainly responsible for the W erosion during the ELMs in He plasmas. The strong in/out asymmetry of the ELM-induced W erosion is observed in He plasmas even at high ELM frequencies beyond 100 Hz. In Ohmic/L-mode plasmas and during the H-mode inter-ELM plasma phases both He 2+ and Be 2+ ionic species are major contributors to the W erosion. Their contribution depends on the electron temperature in the divertor: for T e > 15 eV both species cause significant W sputtering, for T e < 15 eV, B e 2+ ions are solely responsible for the W erosion. Tungsten erosion during in both inter and intra-ELM periods in He-dominated plasmas are significantly larger than in deuterium plasmas. It is 15–25 times larger during the inter-ELM phase and in L-mode discharges at T e = 25–30 eV. On the other hand, the ELM-induced W source is by a factor of 3 larger than in D plasmas.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evaluation of silicon carbide as a divertor armor material in DIII-D H-mode discharges

Silicon carbide (SiC) represents a promising but largely untested plasma-facing material (PFM) for next-step fusion devices. In this work, an analytic mixed-material erosion model is developed by calculating the physical (via SDTrimSP) and chemical (via empirical scalings) sputtering yield from SiC, Si, and C. The Si content in the near-surface SiC layer is predicted to increase during D plasma bombardment due to more efficient physical and chemical sputtering of C relative to Si. Silicon erosion from SiC thereby occurs primarily from sputtering of the enriched Si layer, rather than directly from the SiC itself. SiC coatings on ATJ graphite, manufactured via chemical vapor deposition, were exposed to repeated H-mode plasma discharges in the DIII-D tokamak to test this model. The qualitative trends from analytic modeling are reproduced by the experimental measurements, obtained via spectroscopic inference using the S/XB method. Quantitatively the model slightly under-predicts measured erosion rates, which is attributed to uncertainties in the ion impact angle distribution, as well as the effect of edge-localized modes. After exposure, minimal changes to the macroscopic or microscopic surface morphology of the SiC coatings were observed. Compositional analysis reveals Si enrichment of about 10%, in line with expectations from the erosion model. Extrapolating to a DEMO-type device, an order-of-magnitude decrease in impurity sourcing, and up to a factor of 2 decrease in impurity radiation, is expected with SiC walls, relative to graphite, if low C plasma impurity content can be achieved. Furthermore, these favorable erosion properties motivate further investigations of SiC as a low-Z, non-metallic PFM.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Dynamic deuterium retention properties of tungsten measured using laser-induced breakdown spectroscopy

Dynamic deuterium (D) retention properties of tungsten (W) are investigated under steady-state D plasma exposure in the PISCES-A linear plasma device. In contrast to static retention, dynamic retention is quickly released from the material at the termination of the incident plasma flux, and thus in-operando laser-induced breakdown spectroscopy (LIBS) measurements have been conducted during steady-state D plasma exposure. A procedure is, first, established to extract the dynamic retention component from the in-operando LIBS D I 656.1 nm line intensity, which can contain contributions from dynamic and static retention as well as background D/D 2 gas, excited by both steady-state and laser-induced plasmas. Using the developed procedure, the dynamic D retention in W is systematically examined while scanning the following plasma exposure parameters: incident ion energy, E i , sample temperature, T s , incident ion flux, Γ i . No clear E i dependence is seen in the range of E i ~ 45–175 eV, as expected from a small variation in the average implantation depth (~3-6 nm) of D in W. The dynamic retention is found to monotonously decrease with increasing T s from 348 to 573 K, while the total static retention is reported to peak at T s ~ 500–600 K. It is revealed that the dynamic retention linearly increases with increasing Γ i , and then saturates at Γ i ≥ 0.75 × 10 21 m –2 s –1 . Possible physical mechanisms for the observed dependence of the dynamic retention on T s and Γ i are discussed. Furthermore, sequential pure He, followed by pure D, plasma exposures show that the dynamic D retention is not strongly affected by He bubbles in the near-surface region.

super-saturated surface layer↗
DOE OSTI2022

Predicting tungsten erosion and leakage properties for the new V-shaped small angle slot divertor in DIII-D

Impurity transport modeling of the new tungsten (W)-coated, V-shaped small angle slot (SAS) divertor in the DIII-D tokamak was conducted using the SOLPS-ITER plasma edge code package and the DIVIMP impurity tracking code. The inboard baffle of the current SAS divertor will be shifted closer to the outboard baffle, creating a V-corner at the slot vertex. In addition, the outboard baffle will be coated with 10–15 μm of W for experiments studying high-Z sourcing and leakage in a closed divertor. Modeling of the 'SAS-VW' divertor predicts that these changes to the inner baffle will reduce W gross erosion by 40× relative to the existing SAS divertor when the outer strike point (OSP) is at the V-corner and the ion B × ∇B drift is towards the divertor, driven primarily by significant cooling near the slot vertex. Most W erosion in SAS-VW is expected to occur near the slot entrance, which may pose a higher risk to core contamination than W eroded deeper in the slot. Furthermore, adding a new sheath-based prompt redeposition model increases the sensitivity of redeposition estimates to near-target plasma conditions and may provide more accurate predictions of net erosion. Moving the OSP outboard from the slot vertex ~4 cm onto the W-coated region yields a 40× increase in the gross erosion rate and a 50% decrease in the core leakage fraction. Thus slight variations in strike point location may counteract the potential benefits of the tightly-baffled V slot on minimizing erosion. This impurity transport modeling provides useful guidance for future experiments on the SAS-VW divertor focused on high-Z erosion/redeposition, scrape-off layer transport, and core leakage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Deuterium plasma induced preferential erosion in ultra-high temperature ceramics TiB 2 and ZrB 2 *

Abstract Steady-state deuterium plasma exposures were performed on ultra-high temperature ceramics titanium diboride (TiB 2 ) and zirconium diboride (ZrB 2 ) using the PISCES-RF linear plasma device (LPD) as early screening for first wall, plasma-facing applications. Deuterium plasma exposures were performed using 40 eV ion energies at 240, 525, and 800 °C sample temperatures and 90 eV ion energies at 240 °C sample temperatures to analyze TiB 2 and ZrB 2 surface morphology and chemistry evolution behavior. Post-plasma exposure chemistry characterization of the near surface ( < 50 nm) region of the samples all show transition metal enrichment, indicating boron preferential erosion. Transition metal to boron fractions vary with plasma exposure temperature under the 40 eV ion energy; metal enrichment is maximized at 800 °C and then minimized at 525 °C. SEM micrographs of all plasma exposed sample surfaces show no significant or noticeable plasma induced damage from cracking or blistering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Amorphization and siliconization of silicon carbide as a first wall material

The understanding and prediction of silicon carbide (SiC) material evolution exposed to SOL plasma conditions is of prime interest because SiC represents a promising main chamber wall plasma-facing material for next-step fusion devices (low hydrogenic diffusion, good mechanical and thermal properties under neutron irradiation). Gross and net Si erosion rates from SiC surfaces in contact with a well-diagnosed L-mode plasma in the DIII-D tokamak have been simulated and the surface concentrations of impurities have been tracked as a function of time. Coupled simulation of surface model and impurity transport demonstrates amorphization of crystalline SiC exposed to L-mode plasma due to the accumulation of displacement damages under ion irradiation. This affects the lifetime of SiC plasma facing components. Surface evolution is tightly coupled to impurity transport in the plasma and therefore needs to be integrated with impurity transport simulations to effectively predict Si erosion rates and sub-surface concentrations as a function of time. The simulation workflow couples a semi-analytical surface model to the impurity transport code GITR. The surface model is a homogeneous mixed-material model that tracks physical & chemical sputtering and reflection of impurities. Gross erosion is primarily influenced by the background plasma parameters and redeposition patterns are mainly influenced by the prompt redeposition due to the gyro-orbits of impurity ions. Although crystalline form of SiC is preferable for fusion wall applications because of resistance to neutron irradiation, this work indicates that crystalline SiC will undergo amorphization under D plasma contact with implications of higher sputtering and fuel retention. These results direct us to explore the effects of amorphization on crystalline SiC and further the physics basis of SiC usage as first wall material for fusion environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Wall conditioning effects of boron powder injection in KSTAR with a tungsten divertor

Boron powder dropped into KSTAR plasmas decreased the radiated power, core electron density, and Z eff , indicating that the ablated and redeposited boron powder helped to condition the plasma-facing surfaces. Visible line emission of oxygen and tungsten were also reduced by 50% (80%) with boron injection into H-mode (L-mode) discharges that used the new KSTAR tungsten monoblock lower divertor. Dynamic particle balance analysis found a negligible difference in the inferred wall pumping rate during the steady portion of the discharges. It is inferred that the observed conditioning effects were principally caused by a reduction in intrinsic impurities as opposed to a reduction in wall recycling. These results are in qualitative agreement with low-Z injected powder experiments across many fusion devices, confirming the utility of low-Z powder injection as a real-time wall conditioning tool.

boron powder injection↗
DOE OSTI2020

Deciphering the PMI Surface Chemistry of Lithium-Based PFCs and its Effects on High Performance Plasmas in NSTX

The primary aims or objectives of the proposed work here focus on the dynamic measurement (Illinois PI Allain) and atomistic-based multi-scale computational atomistic simulations (UTK PI: Wirth) of: 1) lithium coatings with re-deposited hydrogenated carbon surfaces and high-Z substrates, 2) lithium coatings on boronized ATJ graphite surfaces and high-Z substrates and 3) lithium coatings on ATJ graphite and high-Z substrates with variation in temperature. Three main primary tasks are proposed to address each of the primary objectives listed above: 1) dynamic in-situ irradiation with D+, He+ species of lithium coatings with variation in interface substrate morphology (e.g. smooth vs rough, fuzz vs nanostructured); 2) validation and coupling with multi-scale computational simulations connecting the irradiated surface to the plasma edge; 3) extrapolation to long-pulse conditions (e.g. function of flux vs fluence studies). In primary objective #3, temperature-based effects will be studied to evaluate three primary mechanisms: a) D uptake and recycling, b) erosion, and c) surface melting and evaporation as a function of substrate morphology and chemistry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Advanced grazing-emission X-ray fluorescence spectroscopy with small-angle neutron scattering for in-vivo surface composition and defect/morphology surface evolution in tokamak PMI

The dynamic and extreme conditions of thermonuclear fusion tokamak plasmas render material surfaces almost impossible to examine in real-time, surface-sensitive conditions. However, combining particle-probe techniques that are not charge-state dependent open the possibilities of in-vivo diagnosis of the plasma-material interface. The reconstituted surfaces of plasma-facing components ranging from first-wall to divertor-component regions in the device vary depending on the complex plasma transport characteristics of the device. For example, in ITER it is predicted that fluxes of the order 10 22 to 10 24 and incident charged-particle energies of 100’s to 1000’s of eV will reach the surface while in the divertor regions within the private-flux and near the inner and outer-strike points would vary from a few eV to 100’s of eV governed by the complex Chodura magnetic sheath dynamics. This means that the penetration range of most charged-particle fluxes would range between 1-100’s of nm (e.g. for fuel particles of D and T and He).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Ex-Situ Surface Characterization Studies and Boundary Plasma Diagnostic Development for DIII-D (Final Report)

This report details the accomplishments for award DE-SC0016318, which sponsored collaborative research activities between the University of Tennessee-Knoxville and the DIII-D experiment at General Atomics, led by the PI (Donovan), which officially began on August 1, 2016 and ended July 31, 2020. Though the official start date for the award was August 1, 2016, the PI had already initiated collaborative activities with DIII-D during 2015 supported by internal UTK start-up funds utilized by the PI. This prior work enabled UTK to have a substantial role in the June 2016 Metal Rings Campaign (MRC). The DOE funds then provided the opportunity to expand the UTK team with funding for students and a postdoc to perform ex-situ analysis on the wide array of samples exposed during the MRC and develop more sophisticated analysis tools and interpretive modeling techniques.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗