Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastic strain engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Temperature dependence of viscoelastic Poisson’s ratio of cement mortar

Abstract Concrete creep research has focused primarily on uniaxial response. However, biaxially prestressed concrete structures are common, resulting in a multiaxial stress state that can complicate the behavior of a viscoelastic material like concrete. Significant creep strains may be induced in directions transverse to each principle stress due to Poisson’s effect. Past research is unclear regarding the viscoelastic or viscoplastic properties of concrete outside of uniaxial response. It has been reported in separate studies that concrete viscoelastic/viscoplastic Poisson’s ratio (VPR) is an increasing, decreasing and constant function with time, with all reported measurements performed at room temperature. In this paper, the 3D basic creep response of mature cement mortar is examined using a confined compression experiment that allows direct determination of the full stress and infinitesimal strain tensors in a single test, which enables the determination of VPR under a multiaxial stress state. For this purpose, a unique, miniature version of the standardized concrete creep frame is designed that is amenable to placing in climate chambers and temperature ovens. The experimental results indicate that the VPR of sealed, mature cement mortar is nearly constant and equal to the elastic at room temperature, while the VPR gradually increases with time when measured at 60 °C.

Construction & Building Technology↗
NASA NTRS2004

Design and Experimental Verification of Deployable/Inflatable Ultra-Lightweight Structures

Because launch cost of a space structural system is often proportional to the launch volume and mass and there is no significant gravity in space, NASA's space exploration programs and various science missions have stimulated extensive use of ultra-lightweight deployable/inflatable structures. These structures are named here as Highly Flexible Structures (HFSs) because they are designed to undergo large displacements, rotations, and/or buckling without plastic deformation under normal operation conditions. Except recent applications to space structural systems, HFSs have been used in many mechanical systems, civil structures, aerospace vehicles, home appliances, and medical devices to satisfy space limitations, provide special mechanisms, and/or reduce structural weight. The extensive use of HFSs in today's structural engineering reveals the need of a design and analysis software and a database system with design guidelines for practicing engineers to perform computer-aided design and rapid prototyping of HFSs. Also to prepare engineering students for future structural engineering requires a new and easy-to- understand method of presenting the complex mathematics of the modeling and analysis of HFSs. However, because of the high flexibility of HFSs, many unique challenging problems in the modeling, design and analysis of HFSs need to be studied. The current state of research on HFSs needs advances in the following areas: (1) modeling of large rotations using appropriate strain measures, (2) modeling of cross-section warpings of structures, (3) how to account for both large rotations and cross- section warpings in 2D (two-dimensional) and 1D structural theories, (4) modeling of thickness thinning of membranes due to inflation pressure, pretension, and temperature change, (5) prediction of inflated shapes and wrinkles of inflatable structures, (6) development of efficient numerical methods for nonlinear static and dynamic analyses, and (7) filling the gap between geometrically exact elastic analysis and elastoplastic analysis. The objectives of this research project were: (1) to study the modeling, design, and analysis of deployable/inflatable ultra-lightweight structures, (2) to perform numerical and experimental studies on the static and dynamic characteristics and deployability of HFSs, (3) to derive guidelines for designing HFSs, (4) to develop a MATLAB toolbox for the design, analysis, and dynamic animation of HFSs, and (5) to perform experiments and establish an adequate database of post-buckling characteristics of HFSs.

Pai, P. Frank↗
DOE OSTI2021

A molecular design approach towards elastic and multifunctional polymer electronics

Next-generation wearable electronics require enhanced mechanical robustness and device complexity. Besides previously reported softness and stretchability, desired merits for practical use include elasticity, solvent resistance, facile patternability and high charge carrier mobility. Here, we show a molecular design concept that simultaneously achieves all these targeted properties in both polymeric semiconductors and dielectrics, without compromising electrical performance. This is enabled by covalently-embedded in-situ rubber matrix (iRUM) formation through good mixing of iRUM precursors with polymer electronic materials, and finely-controlled composite film morphology built on azide crosslinking chemistry which leverages different reactivities with C–H and C=C bonds. The high covalent crosslinking density results in both superior elasticity and solvent resistance. When applied in stretchable transistors, the iRUM-semiconductor film retained its mobility after stretching to 100% strain, and exhibited record-high mobility retention of 1 cm 2 V -1 s -1 after 1000 stretching-releasing cycles at 50% strain. The cycling life was stably extended to 5000 cycles, five times longer than all reported semiconductors. Furthermore, we fabricated elastic transistors via consecutively photo-patterning of the dielectric and semiconducting layers, demonstrating the potential of solution-processed multilayer device manufacturing. The iRUM represents a molecule-level design approach towards robust skin-inspired electronics.

42 ENGINEERING↗
DOE OSTI2026

Part-scale evolution of fine-scale microstructural heterogeneity in solid-state additive manufacturing

Current solid-state additive manufacturing methods, refined through costly and time-consuming trial and error, have spurred interest in computational models that replicate material behavior under typical thermomechanical conditions (e.g., strain-rate ~ 102 s−1). These models, however, struggle to capture time-dependent microstructural evolution. In this work, Additive Friction-Stir Deposition (AFSD) is used as a representative case study for part-scale quantification of microstructure evolution at a fine spatial resolution (200 μm) by examining a liquid-nitrogen-cooled stop-action build via energy-dispersive X-ray diffraction coupled with a multi-channel detector. These results inform modeling efforts by linking process asymmetry to stored plastic strain, residual elastic strain, and texture development, and unlike current state-of-the-art characterization methods (e.g., EBSD or neutron diffraction), this approach provides both the spatial resolution and collection efficiency necessary to quantify fine-scale microstructural heterogeneity over large component volumes. As such, this technique provides essential validation data for computational models, e.g., crystal plasticity, enabling future prediction of heterogeneous behavior in AFSD and other additive manufacturing processes.

Franz, Cole [ORNL] (ORCID:0000000213465881)↗
DOE OSTI2020

A continuum framework for coupled solid deformation–fluid flow through anisotropic elastoplastic porous media

We present a continuum framework for coupled solid deformation–fluid flow in anisotropic elastoplastic porous media. A thermodynamic formulation of the coupled processes gives rise to an anisotropic Biot tensor that is a function of drained elastic tangent moduli tensor of the solid skeleton and the intrinsic bulk modulus of the solid constituent. Two effective stress measures emerge from the formulation, namely, σ', which is energy-conjugate to the elastic strain, and σ'', which is energy-conjugate to the plastic strain. For the special case of transverse isotropy that is commonly encountered in natural rocks, the Biot tensor can be expressed in terms of its normal and tangential components to the bedding plane, along with a microstructure tensor. Apart from its thermodynamic consistency, an advantage of this new formulation is that standard mixed finite element formulation can be employed to discretize the domain and solve initial boundary-value problems. We conduct plane strain simulations of coupled solid deformation–fluid flow in a transversely isotropic porous medium to demonstrate the impacts of material anisotropy, stress history, and the Biot tensor on the system response.

42 ENGINEERING↗
DOE OSTI2022

A finite micro-rotation material point method for micropolar solid and fluid dynamics with three-dimensional evolving contacts and free surfaces

This paper introduces an explicit material point method designed specifically for simulating the micropolar continuum dynamics in the finite deformation and finite microrotation regime. The material point method enables us to simulate large deformation problems while circumventing the potential mesh distortion without remeshing. To eliminate rotational motion damping and loss of angular momentum during the projection, we introduce the mapping for microinertia and angular momentum between particles and grids through the affine particle-in-cell approach. The microrotation and the curvature at each particle are updated through zero-order forward integration of the microgyration and its spatial gradient. We show that the microinertia and the angular momentum are conserved during the projections between particles and grids in our formulation. We verify the formulation and implementation by comparing with the analytical dispersion relation of micropolar waves under the small strain and small microrotation, as well as the analytical soliton solution for solids undergoing large deformation and large microrotation. Additionally we also demonstrate the capacity of the proposed computational framework to handle a wide spectrum of simulations that exhibit size effects in the geometrical nonlinear regime through three representative numerical examples, i.e., a cantilever beam torsion problem, a fragment-impact penetration problem, and a micropolar fluid discharging problem.

42 ENGINEERING↗
NASA NTRS1994

TEXCAD: Textile Composite Analysis for Design. Version 1.0: User's manual

The Textile Composite Analysis for Design (TEXCAD) code provides the materials/design engineer with a user-friendly desktop computer (IBM PC compatible or Apple Macintosh) tool for the analysis of a wide variety of fabric reinforced woven and braided composites. It can be used to calculate overall thermal and mechanical properties along with engineering estimates of damage progression and strength. TEXCAD also calculates laminate properties for stacked, oriented fabric constructions. It discretely models the yarn centerline paths within the textile repeating unit cell (RUC) by assuming sinusoidal undulations at yarn cross-over points and uses a yarn discretization scheme (which subdivides each yarn not smaller, piecewise straight yarn slices) together with a 3-D stress averaging procedure to compute overall stiffness properties. In the calculations for strength, it uses a curved beam-on-elastic foundation model for yarn undulating regions together with an incremental approach in which stiffness properties for the failed yarn slices are reduced based on the predicted yarn slice failure mode. Nonlinear shear effects and nonlinear geometric effects can be simulated. Input to TEXCAD consists of: (1) materials parameters like impregnated yarn and resin properties such moduli, Poisson's ratios, coefficients of thermal expansion, nonlinear parameters, axial failure strains and in-plane failure stresses; and (2) fabric parameters like yarn sizes, braid angle, yarn packing density, filament diameter and overall fiber volume fraction. Output consists of overall thermoelastic constants, yarn slice strains/stresses, yarn slice failure history, in-plane stress-strain response and ultimate failure strength. Strength can be computed under the combined action of thermal and mechanical loading (tension, compression and shear).

Naik, Rajiv A.↗
NASA NTRS1995

TEXCAD: TEXile Composite Analysis for Design

The Textile Composite Analysis for Design (TEXCAD) code provides the materials/design engineer with a user-friendly, desktop computer based tool for the analysis of a wide variety of fabric reinforced woven and braided composites. It can be used to calculate overall thermal and mechanical properties along with engineering estimates of damage progression and strength. TEXCAD also calculates laminate properties for stacked, oriented fabric constructions. It discretely models the yarn centerline paths within the textile repeating unit cell (RUC) by assuming sinusoidal undulations at yarn cross-over points and uses a year discretization scheme (which subdivides each yarn into smaller, piecewise straight yarn slices) together with a 3-D stress averaging procedure to compute overall stiffness properties. In the calculations for strength, it uses a curved beam-on-elastic foundation model for yarn undulating regions together with incremental approach in which stiffness properties for the failed yarn slices are reduced based on the predicted yarn slice failure mode. Nonlinear shear effects and nonlinear geometric effects can be stimulated. Input to TEXCAD consists of: (1) material parameters like impregnated yarn and resin properties such as moduli, Poisson's ratios, coefficients of thermal expansion, nonlinear shear parameters, axial failure strains, and in-plane failure stresses; and (2) fabric parameters like yarn sizes, braid angle, yarn packing density, filament diameter, and overall fiber volume fraction. Output consists of overall thermoelastic constants, yarn slice strains/stresses, yarn slice failure history, in-plane strain response, and ultimate failure strength. Strength can be computed under the combined action of thermal and mechanical loading (tension, compression, and shear). A brief overview of the analytical capabilities, program organization, and modules, input and output parameters, computer platforms, distribution, and modifications/extensions of the TEXCAD code are presented here.

Naik, Rajiv A.↗
DOE OSTI2021

SISGR: Chemomechanics of Far-From-Equilibrium Interfaces (COFFEI)

Portable, reliable, and deployable devices for energy storage and conversion require fundamental changes in design of solid-state composites comprising ceramics and metals. These materials comprise the electrodes and electrolytes of next-generation solid-oxide fuel cells and all solid-state batteries, forming solid-state functional composites. The advent of solid-state batteries – which replace liquid electrolytes with solid electrolytes capable of lithium ion transport for reliable energy storage in portable batteries – and the increased demand space for all solid-state fuel cells capable of oxygen reduction at intermediate temperatures remain important challenges for improved material stability and decreased system cost. However, little is understood about three fundamental facets of materials that enable such solid-state energy applications. First, how do such materials deform, fracture, or delaminate under operando conditions? Second, how does such mechanical deformation limit or facilitate electronic and ionic transport within and across such material interfaces? Third, how we can predictably design interface-rich composites to engineer both structural and electrochemical stability? This COFFEI Group comprised expertise from Materials Science & Engineering and Nuclear Science & Engineering to integrate unique in situ experiments, simulations, and fabricated interfaces that address these fundamental questions in solid-state interfaces of nanoscale composites that will guide solid-state electrochemistry, transport kinetics, and mechanical deformation for nonstoichiometric materials that enable such applications. In particular, we built on COFFEI’s understanding of chemomechanical coupling among defect concentrations, ionic transport, electron transport, and stored elastic energy that is particularly acute in the far-from-equilibrium conditions typical of energy device applications. By tailoring our focus to solid-state interfaces, we addressed these important issues by (a) developing and applying advanced in situ and ex situ characterization tools to characterize model materials and interfaces synthesized with molecular-level control, under both laboratory-controlled and extreme environments representative of energy device operation; and (b) employing computational modeling and simulation frameworks to predict transport mechanisms, reactivity and stability of these model materials and interfaces under significant chemical strains typical of energy device operation. Recent progress provided insights to additional materials systems and electrochemomechanical fatigue and fracture that were not fully envisioned when the program was initiated. Specifically, in the final three years of COFFEI we pursued two integrated thrusts, with complementary focus. Thrust I focused on failure-resistant electrochemomechanical composites, while Thrust II focused on strain-modulated conductivity and reactivity across interfaces. In contrast to our initial COFFEI focus, these thrusts concentrated wholly on solid-state material interfacial interactions and included greater integration of multiscale visualization including in situ electron microscopy of strained structures/interactions and mesoscale simulations. Successful development of functionally superior and long-lived battery and fuel cell systems and stress adaptable oxides requires a deeper, fundamental understanding of the coupling among the historically important subfields of solid-state electrochemistry, transport kinetics, and mechanical deformation for nonstoichiometric metal oxide electrodes. In this program, the understanding and the application of chemomechanical coupling of defect concentrations, ionic transport, electro-catalytic activity and stored elastic energy, particularly acute in the far-from-equilibrium conditions typical of energy device applications, are being refined and implications for device operation clarified, including for miniaturized solid-state batteries and fuel cells.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Coupled phase field damage and crystal plasticity analysis of intragranular fracture: The role of crystallographic orientation and voids

Damage evolution in engineering metal alloys at the grain scale exhibits significant microstructural heterogeneity and anisotropy. These heterogeneities create local hotspots for stress and strain localization, leading to void nucleation. Crystal orientation influences the active slip systems around voids, affecting lattice rotation and potentially forming discontinuities. At low triaxiality, voids may change shape due to lower stress, rotation, elongation, and coalescence. At high triaxiality, the correlation between crystal orientation and void growth rate becomes stronger, resembling the behavior observed in isolated single crystals. Therefore, understanding the effects of crystal orientation, heterogeneous strain, and defect evolution is crucial for single crystal fracture characterization. Here, in this work, a coupled phase-field damage (PFD) and crystal plasticity (CP) model is implemented within a finite element framework to analyze crystal deformation and failure. The CP method employs a dislocation density-based constitutive model, while intragranular failure is modeled using an anisotropic PFD method. The PFD model considers both the stored energy due to elastic stretching and the energy release due to defect formation and crack formation. A single crystal Al2219 with an intracrystalline spherical void is chosen to analyze fracture. The study finds that fracture propagation is strongly correlated with crystal orientations. This coupled CP-PFD model provides accurate failure prediction in crystalline materials by incorporating the effects of crystal orientations and existing voids. This study demonstrates how the local microstructure and defects influence plastic deformation and failure mechanisms in metal alloys.

Aluminum alloy↗
DOE OSTI2020

Tailoring ductile-phase toughened tungsten hierarchical microstructures for plasma-facing materials

Biological materials, such as bones, nacre, etc., have been found to show attractive and unique combinations of stiffness, strength and fracture toughness. Research has been conducted in various engineering areas to mimic the naturally hierarchical microstructures or nanostructures of these materials to produce materials with optimum stiffness, high strength and fracture toughness for their intended structural applications. In the same objective, this work applies a multiscale microstructural approach recently developed to investigate the deformation and fracture behavior of ductile phase toughened tungsten (W) materials such as tungsten-nickel/iron (W-Ni/Fe) composites that possess lamellar-like and hierarchical “brick-and-mortar” (BAM) microstructures. First, the approach is used to simulate tensile loading of W-Ni/Fe specimens cut out from hot-rolled W-Ni/Fe plates which possess lamellar-like microstructures. The finite element model of the gage section of the specimen consists of a W-Ni/Fe dual-phase microstructural domain in which the constitutive behaviors of W and Ni/Fe phases are described by an elastic-plastic damage model. The predicted material stress-strain response and crack pattern development as a function of loading are then compared to the corresponding experimental results to determine the constitutive model parameters for W and Ni/Fe. Subsequently, the model parameters are used to analyze W-Ni/Fe BAM microstructures that are artificially created to investigate the effects of microstructural features and morphologies on the composite stress-strain response, damage, and fracture patterns. The modeling shows that regular BAM microstructures that experience bridging mechanism combined with crack penetration across W-phase regions exhibit significantly higher strengths than the rather random lamellar-like microstructures. More significantly, however adjusting the brick’s length-to-height ratio, the BAM microstructure can be designed to allow a more distributed damage zone which leads to increased strength, ductility and fracture energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tailoring Nitinol for elastocaloric application

This study focuses on tailoring commercial Nitinol, the most commonly used elastocaloric material, for near-room-temperature cooling applications. Short heat treatments near 500 °C were used to fine-tune the material’s transition temperature, resulting in austenite finish temperatures ranging from 6.0 to 25.5°C and altered superelastic and elastocaloric properties. Plateau stresses decreased while temperature changes rose from 21.5°C up to 27.9°C at 6% strain. Significant variability in the Nitinol response when testing below its austenite finish temperature was observed. In conclusion, the effect of mechanical cycling on transition temperatures was also evaluated, demonstrating an increase for all the samples.

Efficiency↗
DOE OSTI2020

Implementation of Creep-Damage Model for Concrete Fracture in MOOSE

Numerical implementation of an isotropic creep-damage model for concrete in multiphysics object-oriented simulation environment (MOOSE) finite element framework is presented in this paper. The constitutive model considers the combined effect of instantaneous and delayed strains on damage propagation. The implementation considers creep using generalized Maxwell or Kelvin-Voigt models. Using strain splitting assumptions, the total mechanical strains are split into elastic and creep components. Damage is considered to evolve as a function of the elastic and creep strains. This work considers damage as a function of fracture energy using the characteristic length of each finite element. This approach preserves the energy release rate of each element and avoids vanishing energy dissipation as the mesh is refined. Further, a creep-damage parameter is used to quantify the effect of creep strain on damage. The model is tested against published results on notched three-point bending specimens involving non-linear creep and predicts that about a third of the creep strain contributes towards damage for the experiments simulated. Results show that the proposed framework has predictive capabilities, and the model can be extended for more complex systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strain-Mediated Sn Incorporation and Segregation in Compositionally Graded Ge 1– x Sn x Epilayers Grown by MBE at Different Temperatures

We investigated the process of Sn incorporation and surface segregation for compositionally graded Ge 1–x Sn x epilayers grown on high-quality Ge (001) substrates. Here, the growth resulted in pseudomorphic GeSn layers with a ~6% maximal Sn fraction at a constant substrate temperature. The maximal fraction of Sn was increased to 9.0% when the growth temperature was continuously lowered while increasing the Sn flux. The analysis of surface droplets and SIMS profiles of elemental composition give evidence of Sn rejection during the growth, potentially associated with a critical energy of elastic strain. The intentional reduction of the coherent strain by decreasing the Sn flux near the sample surface has been shown to trap a higher fraction of Sn in the Ge 1–x Sn x layer and lower surface segregation. Our results demonstrate that strain relief by misfit dislocations in the compositionally graded layer is inhibited, which leads to Sn segregation. Specifically, the compressive strain in the graded Ge 1–x Sn x epilayer is effectively “zero” near the interface with the Ge substrate and increases up to about –1.5 × 10 –2 near the surface. Thus, although the nucleation of a dislocation may reduce the compressive strain for the top region of the epilayer, it is not beneficial for the bottom region.

42 ENGINEERING↗
DOE OSTI2025

Egg yolk as a model for gelation: From rheometry to flow physics

Egg yolks are an excellent model for studying sol-gel transitions, particularly the power law viscoelasticity that defines the critical point of gelation. However, prior studies lack comprehensive datasets and fail to visualize flow behavior linked to temperature and time-dependent linear and nonlinear rheology. Here, we present a detailed dataset characterizing egg yolk viscoelasticity across temperature, time, and forcing amplitude using oscillatory shear, step strain, step stress, and constant high strain rate. Novel protorheology visualizations link rheological properties with observable flow behavior. Our findings highlight the nuanced determination of the critical gel point, emphasizing observation timescale dependencies. We compare methods to identify critical temperatures for gelation, including power law viscoelasticity, moduli crossover, diverging zero-shear viscosity, and emerging equilibrium elastic modulus, while visualizing flow consequences near these transitions. Egg yolk is an accessible, realistic, and nontoxic material relevant to the physicist and the chef alike, making it ideal for understanding the rheology of critical gels. By integrating protorheology photos and videos with rigorous rheometric data, we deepen the understanding of critical gels, with broader impacts for studying other materials with sol-gel transitions.

Marsh, Maxwell C. [Department of Mechanical Scienc↗
DOE OSTI2025

Electro-Thermo-Mechanical (ETM) Study on Submarine Dynamic Power Cables (SDPC) for Offshore Wind Transmission

Understanding the failure mechanisms of submarine dynamic power cables (SDPC) is critical for innovative design to meet the 2035 cost reduction target of U.S. DOE Floating Offshore Wind Shot. This is important because the current design suffers a significant failure rate in the field. This project conducted a systematic electro-thermo-mechanical (ETM) experimental study on the power cores extracted from a 15kV power cable with three cores of copper conductor, ethylene propylene rubber (EPR) insulation, and continuously corrugated welded aluminum armor (CCWA). An ETM testing system was developed by integrating a high voltage (HV) amplifier, two ceramic heaters, and a rod-plate transverse compression setup into a mechanical testing machine. Increasing temperature from room temperature (RT, 22 degree C) to 90 degree C resulted in the 67% decrease in the failure mechanical load as defined by the dielectric breakdown. Under creep mechanical loading, the dielectric breakdown time was decreased by 70% for a given mechanical load when the specimen temperature increased from RT to 90oC. The failure strain in both monotonic and creep mechanical loading modes was related to the maximum mechanical load applied. Although the dielectric breakdown occurred in the ETM test, the post-test measurement revealed an impressive recovery of electric resistance. The failure analysis on cross section of tested specimens indicated a sizable gap across insulation layer near the area between copper conductor and loading rod, which apparently resulted from online dielectric failure and offline elastic recovery of components including conductor and insulation layer.

17 WIND ENERGY↗
DOE OSTI2021

Tuning Point Defects by Elastic Strain Modulates Nanoparticle Exsolution on Perovskite Oxides

Exsolution generates stable and catalytically active metal nanoparticles via phase precipitation out of a host oxide. An ability to control the size and dispersion of the exsolution particles is desirable for design of nanostructured (electro)catalysts. In this work, we demonstrate that tuning point defects by lattice strain affects both the thermodynamics and the kinetics of iron (Fe 0 ) exsolution on La 0.6 Sr 0.4 FeO 3 (LSF) thin film model. By combining in situ surface characterization and ab initio defect modeling, we show oxygen vacancy and Schottky defects to be the primary point defects formed upon Fe0 exsolution. Lattice strain tunes the formation energy, and thus the abundance of these defects, and alters the amount and size of the resulting exsolution particles. In addition, we find that the density of exsolved nanoparticles matches the concentration of oxygen vacancy pairs, thus pointing to the surface oxygen vacancy pairs as preferential nucleation sites for exsolution. The tensile-strained LSF with a facile formation of these critical point defects results in a higher Fe 0 metal concentration, a larger density of nanoparticles, and a reduced particle size at its surfaces. These results provide important mechanistic insights and highlight the role of point-defect engineering in designing nanostructured catalysts in energy and fuel conversion technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Physical Properties of Hilti HIT-RE 500 V3 After Irradiation: Slant Shear, Tensile, Flexural, and Compressive

There are various applications in which epoxy adhesives may be used within hot-cell environments. These epoxies currently see limited use within hot cells since it is known that organics see degradation after small doses even as low as 50 kilogray (kGy). These losses in physical property strengths limit the use of these epoxies to non-structural applications. In modern construction, however, the use of epoxies to bond structural components such as rebar or threaded anchors is becoming increasingly prevalent. To employ these types of materials the Idaho National Laboratory (INL) has begun investigating the specific degradation properties of epoxies for use in structural applications in environments where radiation is present. Hilti HIT-RE 500 V3 is used extensively in new construction and renovation projects across the world. The INL has conducted various tests on this epoxy for low dose environments. These tests include tensile, flexural, compression, and slant shear tests following the American Society for Testing Material International (ASTM) standards D638, D790, D695, and C882/882M respectively. Two sample sets for each test were created where the baseline specimens were not irradiated, and another set was irradiated to an accumulated dose of approximately 50-60 kGy. All the samples were destructively tested and analyzed focusing on the change in physical properties, examples of these tests are shown in Figures 1-4. Tensile testing results indicate a 0.9% loss in maximum load capacity, a 0.5% loss in tensile stress at maximum load, a 1.4% loss in tensile strain at break, and a 15% decrease in modulus of elasticity. Flexural testing results display an increase in all the following: 12% in strain at maximum load, 10% in maximum load capacity, 5% in stress at maximum load, and 3% in young’s modulus. The compressive physical properties after irradiation display a 1% increase in maximum load, a 3% decrease in stress at yield, and a 5% decrease in modulus of elasticity. The maximum compressive stress saw no measurable change after irradiation. The slant shear specimens after irradiation displayed a 2% increase in maximum load capacity and maximum compressive stress. Though a structural analysis would have to be completed as is normal for building design the increases and decreases in the measured physical properties indicate that this material may be used for structural applications in low dose hot-cell environments without adhesive failure.

36 MATERIALS SCIENCE↗