Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “system frequency response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Hue-saturation-intensity split-spectrum processing of Seasat radar imagery

Characteristics of terrain features in orbital radar imagery are investigated on the basis of radar physics and the human visual system. Signal scattering, the dominant factor in radar imagery, is caused by look angle and relief displacement. Power spectra characteristics are explored, noting that surface scattering dominates the low frequencies and slope significantly affects the high frequency tone variations. The maximum human visual response has been identified for achromatic scenes as 7 cycles per degree, whereas in radar imagery the low frequency half-power point occurs near 2.5 cycles/deg. Image feature size at a scale of 1:500,000 has been calculated for the maximum human response at 1.25 km. A hue-saturation-intensity transformation is presented for displaying two or three data sets on the same image and is demonstrated for Seasat SAR imagery. The transformation is shown to restore low spatial frequencies to the SAR imagery in order to identify terrain features which would otherwise not be visually discernible.

Daily, M.↗

Active control of sound transmission/radiation from elastic plates by vibration inputs. I - Analysis

Active control of sound radiation from vibrating plates by oscillating forces applied directly to the structure is analytically studied. The model consists of a plane acoustic wave incident on a clamped elastic circular thin plate. Control is achieved by point forces, and quadratic optimization is used to calculate the optimal control gains necessary to minimize a cost function proportional to the radiated acoustic power (the transmitted field). The results show that global attenuation of broadband radiated sound levels for low to mid-range frequencies can be achieved with one or two control forces, irrespective of whether the system is on or off resonance. The efficiency of the control strategy is demonstrated to be related to the nature of the coupling between the plate modes of response and the radiated field.

Fuller, C. R.↗

Structural dynamic and control considerations for Space Station transportation node concepts

This paper discusses the results of two studies which investigated the expected low frequency dynamic characteristics of conceptual Mars and lunar transportation nodes. Both concepts are based on evolution of the assembly-complete Space Station Freedom configuration by the addition of keels, booms, and modules. Finite-element models of the concepts were developed and a set of undamped modes and frequencies was computed below 2 Hz for each concept. The modes were used as basis vectors for modal analyses describing the dynamic response of the structures to typical reboost maneuvers. The reboost maneuvers had fairly complex loading characteristics since the reaction control system (RCS) jets used for the maneuvers were off-modulated to control pitch and yaw attitude. Interaction of the dynamic response of the structure with the closed-loop attitude control system is investigated for both concepts. The elastic response in the solar dynamic region is investigated to evaluate the severity of the dynamic environment, since the solar dynamic systems have stringent sunpointing requirements which must be maintained during the reboost maneuver.

Cooper, Paul A.↗

Rotor dynamic considerations for large wind power generator systems

Successful large, reliable, low maintenance wind turbines must be designed with full consideration for minimizing dynamic response to aerodynamic, inertial, and gravitational forces. Much of existing helicopter rotor technology is applicable to this problem. Compared with helicopter rotors, large wind turbines are likely to be relatively less flexible with higher dimensionless natural frequencies. For very large wind turbines, low power output per unit weight and stresses due to gravitational forces are limiting factors. The need to reduce rotor complexity to a minimum favors the use of cantilevered (hingeless) rotor configurations where stresses are relieved by elastic deformations.

Ormiston, R. A.↗

Pyroshock Environments Characterized for Spacecraft Missions

Pyrotechnic shock, or pyroshock, is the transient response of a structure to loading induced by the ignition of pyrotechnic (explosive or propellant activated) devices. These devices are typically used to separate structural systems (e.g., separate a spacecraft from a launch vehicle) and deploy appendages (e.g., solar panels). Pyroshocks are characterized by high peak acceleration, high-frequency content, and short duration. Because of their high acceleration and high-frequency, pyroshocks can cause spaceflight hardware to fail. Verifying by test that spaceflight hardware can withstand the anticipated shock environment is considered essential to mission success. The Earth Observing System (EOS) AM-1 spacecraft for NASA's Mission to Planet Earth is scheduled to be launched on an Atlas IIAS vehicle in 1999, and the NASA Lewis Research Center is the launch vehicle integrator for this NASA Goddard Space Flight Center spacecraft. The EOS spacecraft was subjected to numerous ground shock tests to verify that its scientific instruments and avionics components will withstand the shock-induced vibration produced when the spacecraft separates from the launch vehicle. Shock test data from these tests represent the third largest available pyroshock database in the United States. Future spacecraft missions will directly benefit from the knowledge gained from these tests. The payload separation system used for EOS is a new system that operates by firing six separation nuts. This system was tested to verify its functional operation and to characterize the resulting shock levels. The launch vehicle contractor (Lockheed Martin Astronautics) and spacecraft contractor (Lockheed Martin Missiles & Space) completed 16 separation test firings. This resulted in an unusually large amount of pyroshock data. Typically, only one or two pyroshock test firings are performed for a spacecraft mission. Because of the size of this separation system shock database, engineers were able to perform unique statistical analyses to characterize the distribution of the test data. For example, it was proven that the shock data follow a lognormal distribution, a concept often assumed but rarely proven. The test-to-test repeatability of the shock source level was analyzed, and the effects of various test configurations and separation nut production lots were examined and quantified. Engineers investigated the change in shock level as the shock traveled from the spacecraft separation interface to the avionics components of the upper stage and analyzed the effects of the structural fidelity (simulator versus real) of the components and their weight on vibrational response. In addition, the shock attenuation with distance and across joints was quantified and compared with concepts originally generated in 1970, and the effects of separation nut preload and firing sequences effects were examined. Because of this EOS shock testing and the analyses performed at NASA Lewis, a significant amount of new information on pyroshock and its characteristics is now available to the aerospace industry. We hope that this information will help future spacecraft test planners to perform better and cheaper spacecraft separation shock tests and to better understand their test data.

Hughes, William O.↗

Transport properties of lithium ions doped vanado-bismuth-tellurite glasses

The glasses of composition (65-x)V{sub 2}O{sub 5}-xLi{sub 2}O-20TeO{sub 2}-15Bi{sub 2}O{sub 3} (x = 15 and 25 mol%) were prepared by conventional melt quenching method and their electrical conductivity and dielectric measurements have been carried out in the frequency range 40 Hz to 6 MHz over a temperature 373 to 473 K. The conductivity values increased with both Li{sub 2}O concentration and temperature. Interestingly, the dielectric response showed the existence of a negative capacitance effect in the present glass system and concluded that this effect arose from the presence of external inductive reactance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photonic Software Defined Radio

Wireless links are the most popular form of communications with an ever-growing demand for speed. This has resulted in an overpopulated Radio Frequency (RF) spectrum with not enough bandwidth to meet demand. The two main tactics utilized by the wireless community to overcome this problem is to 1) put more data in a given bandwidth, i.e. higher spectral efficiency and 2) use the available bandwidth more efficiently by tuning the user’s channel (i.e. carrier frequency) to an unused part of spectrum. Higher spectral efficiency is achieved by using complex signals that carry information on both the in-phase (I) carrier and quadrature-phase (Q) carrier, known as Quadrature Amplitude Modulation (QAM), and increasing the number of levels on each carrier, known as the constellation size (4QAM, 16QAM etc.). However higher constellation sizes and higher bandwidth require higher fidelity RF signals. This project looked at a photonic-based high-fidelity RF amplitude and phase modulator which modulates the amplitude and phase of femtosecond laser pulses to generate relatively high-power complex microwave waveforms at carrier frequencies up to 70GHz. The goal of the feasibility study was to build a proof-of-concept system in a laboratory setting that demonstrates the photonic generation of QAM signals at electronically tunable RF carrier frequencies. Our lab prototype achieved a signal-to-noise-and-distortion (SINAD) ratio of 39dB over a 500MHz bandwidth. The signal-to-noise ratio (SNR) of the system was measured at 42dB over a 500MHz bandwidth which is on par with state-of-the-art. The main limitation to the SINAD was the inadequate pre-compensation of the electronic Digital-to-Analog Converter (eDAC) and amplifier frequency response as well as the noise of the measurement equipment. This was backed up by simulations which showed that with perfect pre compensation and using ideal measurement equipment, a noise limited SINAD of 47dB could be achieved. We also showed, through simulations, that multiple DACs could be “optically stacked” to achieve 54dB SINAD.

42 ENGINEERING↗

The effect of a visual/motion display mismatch in a single axis compensatory tracking task

An experiment was performed to determine the effect of a performance mismatch between the visual and motion display systems on a real time piloted aircraft simulation. Pilots performed a compensatory roll tracking task with dynamics typical of medium jet transports. Between 0 and 10 rad/sec, visual and motion system responses were equivalent to either unity or a first order lag at 4.8 rad/sec. Pilot describing functions and error scores were calculated. Results show that the mismatch between visual and motion display systems has no significant effect. It is the absence of high frequency visual and/or motion cues which significantly affects pilot performance.

Shirachi, D. K.↗

Whistler mode noise in Jupiter's inner magnetosphere

A study is made of the amplitude and spectral extent of whistler mode noise in the inner magnetosphere of Jupiter. It is found that the 'hat-shaped' pitch angle distributions of energetic electrons (21 and 31 MeV at L=3) are consistent with those predicted in the presence of a band-limited spectrum of whistler mode noise. The equatorial maximum linear growth rate of parallel propagating whistlers are consistent with those necessary to limit the energetic electron intensities by the whistler mode instability. It is noted that the wave phase speeds before wave reflection can occur at high latitudes and that wave growth is limited to a disk-like region centered around the magnetic equator. The frequency extent of the whistler mode noise spectrum may be estimated by the range of frequencies maximally unstable to equatorial linear growth. A value is found for the spectral density of the broadband whistler mode noise necessary to balance radial diffusion of energetic electrons above the critical range, and an expression is derived for the energetic electron system response to fluctuations about the limiting flux value.

Sentman, D. D.↗

Development of monofilar rotor hub vibration absorber

A design and ground test program was conducted to study the performance of the monofilar absorber for vibration reduction on a four-bladed helicopter. A monofilar is a centrifugal tuned two degree-of-freedom rotor hub absorber that provides force attenuation at two frequencies using the same dynamic mass. Linear and non-linear analyses of the coupled monofilar/airframe system were developed to study tuning and attenuation characteristics. Based on the analysis, a design was fabricated and impact bench tests verified the calculated non-rotating natural frequencies and mode shapes. Performance characteristics were measured using a rotating absorber test facility. These tests showed significant attenuation of fixed-system 4P hub motions due to 3P inplane rotating-system hub forces. In addition, detuning effects of the 3P monofilar modal response were small due to the nonlinearities and tuning pin slippage. However, attenuation of 4P hub motions due to 5P inplane hub forces was poor. The performance of the 5P monofilar modal response was degraded by torsional motion of the dynamic mass relative to the support arm which resulted in binding of the dynamic components. Analytical design studies were performed to evaluate this torsional motion problem. An alternative design is proposed which may alleviate the torsional motion of the dynamic mass.

Duh, J.↗

Measured effects of wind turbine generation at the Block Island Power Company

Data measurements made on the NASA MOD-OA 200-kw wind-turbine generator (WTG) installed on a utility grid form the basis for an overall performance analysis. Fuel displacement/-savings, dynamic interactions, and WTG excitation (reactive-power) control effects are studied. Continuous recording of a large number of electrical and mechanical variables on FM magnetic tape permit evaluation and correlation of phenomena over a bandwidth of at least 20 Hz. Because the wind-power penetration reached peaks of 60 percent, the impact of wind fluctuation and wind-turbine/diesel-utility interaction is evaluated in a worst-case scenario. The speed-governor dynamics of the diesel units exhibited an underdamped response, and the utility operation procedures were not altered to optimize overall WTG/utility performance. Primary findings over the data collection period are: a calculated 6.7-percent reduction in fuel consumption while generating 11 percent of the total electrical energy; acceptable system voltage and frequency fluctuations with WTG connected; and applicability of WTG excitation schemes using voltage, power, or VARS as the controlled variable.

Wilreker, V. F.↗

Punch stretching process monitoring using acoustic emission signal analysis. II - Application of frequency domain deconvolution

The coloring effect on the acoustic emission signal due to the frequency response of the data acquisition/processing instrumentation may bias the interpretation of AE signal characteristics. In this paper, a frequency domain deconvolution technique, which involves the identification of the instrumentation transfer functions and multiplication of the AE signal spectrum by the inverse of these system functions, has been carried out. In this way, the change in AE signal characteristics can be better interpreted as the result of the change in only the states of the process. Punch stretching process was used as an example to demonstrate the application of the technique. Results showed that, through the deconvolution, the frequency characteristics of AE signals generated during the stretching became more distinctive and can be more effectively used as tools for process monitoring.

Liang, Steven Y.↗

Recursive form of the eigensystem realization algorithm for system identification

An algorithm is developed for recursively calculating the minimum realization of a linear system from sampled impulse response data. The Gram-Schmidt orthonormalization technique is used to generate an orthonormal basis for factorization of the data matrix. The system matrix thus identified is in upper Hessenberg form, which has advantages for the identification of modal parameters including damping coefficients, frequencies, mode shapes, and modal participation factors. It also has the property that once an element of the system matrix is computed, it is never altered as the dimension of the model is increased in the recursive process. Numerical examples are presented for comparison of the recursive and nonrecursive forms of the eigensystem realization algorithm.

Longman, Richard W.↗

Effects of a trailing edge flap on the aerodynamics and acoustics of rotor blade-vortex interactions

The use of a trailing edge flap on a helicopter rotor has been numerically simulated to determine if such a device can mitigate the acoustics of blade vortex interactions (BVI). The numerical procedure employs CAMRAD/JA, a lifting-line helicopter rotor trim code, in conjunction with RFS2, an unsteady transonic full-potential flow solver, and WOPWOP, an acoustic model based on Farassat's formulation 1A. The codes were modified to simulate trailing edge flap effects. The CAMRAD/JA code was used to compute the far wake inflow effects and the vortex wake trajectories and strengths which are utilized by RFS2 to predict the blade surface pressure variations. These pressures were then analyzed using WOPWOP to determine the high frequency acoustic response at several fixed observer locations below the rotor disk. Comparisons were made with different flap deflection amplitudes and rates to assess flap effects on BVI. Numerical experiments were carried out using a one-seventh scale AH-1G rotor system for flight conditions simulating BVI encountered during low speed descending flight with and without flaps. Predicted blade surface pressures and acoustic sound pressure levels obtained have shown good agreement with the baseline no-flap test data obtained in the DNW wind tunnel. Numerical results indicate that the use of flaps is beneficial in reducing BVI noise.

Charles, B. D.↗

Identifying the unmodified structural characteristics using multiple modifications

This paper describes a procedure for estimating the free-free modal characteristics of a system by testing multiple constrained states. The procedure eliminates the influences of the constraints on the modal parameters and provides important information at the connection points. For very stiff or very flexible test articles, it is difficult to support the test article and to measure uncompromised modal parameters. The method described in this paper measures the forces and/or responses at constraint-connection points and uses a direct parameter estimation algorithm to calculate the system's free-free characteristics. These free-free characteristics retain the local information at the connection or boundary points, thereby including the important local high frequency residual effects in the modal model.

Barney, Patrick↗

Hardware-in-the-loop Testing of Signal Temporal Logic Frequency Control in a Microgrid

This paper presents a hardware-in-the-loop (HITL) testing and lessons learned for a signal temporal logic (STL) frequency control in a microgrid setting. In contrast to most, if not all, traditional control mechanisms, the STL control allows for including temporal constraints in the control formulation to handle sophisticated specifications from grid codes and protection relays. This feature provides richer descriptions of control specifications to address both magnitude and time simultaneously, hence a valuable tool for power system operation and control. An ultra-low voltage (24V) HITL microgrid platform consisting of two type-3 wind turbine generators and one diesel generator is used to test the proposed STL frequency control. In experimental case studies, we demonstrate that the HITL frequency responses closely match the simulated ones and strictly satisfy the designed STL control specifications.

Ferrari Maglia, Max↗

Gyrotropic Hall effect in Berry-curved materials

We study the ac Hall response induced by passage of dc transport current in two- and three-dimensional metals with gyrotropic point groups—the gyrotropic Hall effect—and consider the phenomenon of current-induced optical activity in noncentrosymmetric metals as a physical application of our theory. While the effect is expected to be present in single crystals of any noncentrosymmetric metal, we expect it to be strongest in enantiomorphic Weyl semimetals. Using the semiclassical kinetic equation approach, we present several mechanisms underlying the gyrotropic Hall effect. Amongst them, the intrinsic mechanism is determined by the Berry curvature dipole, while extrinsic impurity-induced processes are related to skew scattering and side-jump phenomena. In general, the intrinsic and extrinsic contributions can be of similar magnitude. We discuss the gyrotropic Hall effect for all frequencies of practical interest, from the dc transport limit, to optical frequencies. We show that for frequencies that are small compared to relevant band splittings, the trace of the gyrotropic Hall tensor in three-dimensional materials is proportional to a topological, quantized Berry charge, and therefore is robust in gyrotropic Weyl systems. This implies that polycrystals of strongly gyrotropic Weyl semimetals will demonstrate strong current-induced optical activity, whereas the response vanishes for polycrystalline ordinary metals. Furthermore the current-induced optical activity can be considered a valuable tool in identifying the topological nature of a material.

36 MATERIALS SCIENCE↗

Design definition of the Laser Atmospheric Wind Sounder (LAWS), phase 2. Volume 1: Executive summary

The LAWS phase 1 and phase 2 studies have been completed on schedule and have led to significant advances in CO2 laser development. The Phase 2 Design Definition Study has shown that a large scanning mirror/high pulse energy laser LAWS Instrument is feasible and within the existing technology. The capability to monitor wind velocities with backscatter ratios of 10(exp 11) m(exp -1) SR(exp -1) is feasible. The weight budget allocated for the baseline LAWS is adequate, and sufficient reserves exist with the potential downsized configuration. With the possible decrease in available power from the baseline of 2.2 kW guideline, power and shot management is critical for the baseline configuration (15 to 20 J). This is particularly true during the 100 day occultation period each year. With the downsized configurations (5 to 7 J), power management is still necessary during the occultation but is primarily limited to shot management over the polar regions. The breadboard effort has produced significant laser advances for a tight 18 month schedule and the minimum budgets available from NASA, Lockheed, and TDS. Using the NASA funds and Lockheed and TDS fixed assets budgets, the breadboard was designed, fabricated, and brought on-line with first laser light within 16 months after ATP. First laser beam was obtained on 21 April 1992 at a 5 J power level. Tests since then have been conducted at sustained, repetitive pulse levels of over 7 J and 20 Hz. This is an increase of over two or three times greater than any system previously developed from this type laser. Increased power levels and additional life tests will be accomplished in the next LAWS phase. The Lockheed LAWS design will operate in the gravity gradient mode on-orbit, and all possible instrument vibration and jitter modes have been considered. Adequate pointing stability and control is state-of-the-art technology for the critical time periods, frequency rates, and control responses required by LAWS. Lockheed recommends a 6-1/2 year phase C/D program for LAWS to provide adequate feedback from the engineering unit and the qualification unit to the final flight unit. Assuming a one year period for LAWS integration to the spacecraft, followed by a six-month period for launch vehicle integration, LAWS could be successfully developed and launched in eight years. Our baseline design or downsized design can be accommodated by either the Atlas 2AS or the Delta launch vehicles. Lockheed's recommendation is that, based on the successful phase 2 design study and breadboard program, a follow-on 18 month extended breadboard testing program and additional system engineering studies, primarily in interfacing with a to be defined platform, be initiated. This should be immediately followed by the phase C/D program, leading to a LAWS launch in late 2001 or early 2002.

Source record↗