Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,513 records · Page 84
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Porous media matric potential and water content measurements during parabolic flight

Control of water and air in the root zone of plants remains a challenge in the microgravity environment of space. Due to limited flight opportunities, research aimed at resolving microgravity porous media fluid dynamics must often be conducted on Earth. The NASA KC-135 reduced gravity flight program offers an opportunity for Earth-based researchers to study physical processes in a variable gravity environment. The objectives of this study were to obtain measurements of water content and matric potential during the parabolic profile flown by the KC-135 aircraft. The flight profile provided 20-25 s of microgravity at the top of the parabola, while pulling 1.8 g at the bottom. The soil moisture sensors (Temperature and Moisture Acquisition System: Orbital Technologies, Madison, WI) used a heat-pulse method to indirectly estimate water content from heat dissipation. Tensiometers were constructed using a stainless steel porous cup with a pressure transducer and were used to measure the matric potential of the medium. The two types of sensors were placed at different depths in a substrate compartment filled with 1-2 mm Turface (calcined clay). The ability of the heat-pulse sensors to monitor overall changes in water content in the substrate compartment decreased with water content. Differences in measured water content data recorded at 0, 1, and 1.8 g were not significant. Tensiometer readings tracked pressure differences due to the hydrostatic force changes with variable gravity. The readings may have been affected by changes in cabin air pressure that occurred during each parabola. Tensiometer porous membrane conductivity (function of pore size) and fluid volume both influence response time. Porous media sample height and water content influence time-to-equilibrium, where shorter samples and higher water content achieve faster equilibrium. Further testing is needed to develop these sensors for space flight applications.

Parabolic Flight↗
DOE OSTI2021

In-flight positional and energy use data set of a DJI Matrice 100 quadcopter for small package delivery

Abstract We autonomously directed a small quadcopter package delivery Uncrewed Aerial Vehicle (UAV) or “drone” to take off, fly a specified route, and land for a total of 209 flights while varying a set of operational parameters. The vehicle was equipped with onboard sensors, including GPS, IMU, voltage and current sensors, and an ultrasonic anemometer, to collect high-resolution data on the inertial states, wind speed, and power consumption. Operational parameters, such as commanded ground speed, payload, and cruise altitude, were varied for each flight. This large data set has a total flight time of 10 hours and 45 minutes and was collected from April to October of 2019 covering a total distance of approximately 65 kilometers. The data collected were validated by comparing flights with similar operational parameters. We believe these data will be of great interest to the research and industrial communities, who can use the data to improve UAV designs, safety, and energy efficiency, as well as advance the physical understanding of in-flight operations for package delivery drones.

42 ENGINEERING↗
DOE OSTI2023

Neck Muscle Coactivation Response to Varied Levels of Mental Workload During Simulated Flight Tasks

Objective To evaluate neck muscle coactivation across different levels of mental workload during simulated flight tasks. Background Neck pain (NP) is highly prevalent among military aviators. Given the complex nature within the flight environment, mental workload may be a risk factor for NP. This may induce higher levels of neck muscle coactivity, which over time may accelerate fatigue, increase neck discomfort, and affect flight task performance. Method Three counterbalanced mental workload conditions represented by simulated flight tasks modulated by interstimulus frequency and complexity were investigated using the Modifiable Multitasking Environment (ModME). The primary measure was a neck coactivation index to describe the neuromuscular effort of the neck muscles as a system. Additional measures included perceived workload (NASA TLX), subjective discomfort, and task performance. Participants ( n = 60; 30M, 30F) performed three test conditions over 1 hr each while seated in a simulated seating environment. Results Neck coactivation indices (CoA) and subjective neck discomfort corresponded with increasing level of mental workload. Average CoAs for low, medium, and high workloads were: .0278(SD = .0232), .0286(SD = .0231), and .0295(SD = .0228), respectively. NASA TLX mental, temporal, effort, and overall scores also increased with the level of mental workload assigned. For ModME task performance, the overall performance score, monitoring accuracy, and resource management accuracy decreased while reaction times increased with the increasing level of mental workload. Communication accuracy was lowest with the low mental workload but had higher reaction times relative to increasing workload. Conclusion Mental workload affects neck muscle coactivation during combinations of simulated flight tasks within a simulated helicopter seating environment. Application The results of this study provide insights into the physical response to mental workload. With increasing multisensory modalities within the work environment, these insights may assist the consideration of physical effects from cognitive factors.

Behavioral Sciences↗
DOE OSTI2026

Drone Flight Data Logs

This dataset represents the open-air tests for the drones when testing different flight scenarios. For some flights we created and tested with a set of onboard sensors. For others we used the native logs for the drones. We recorded relevant conditions for each of the flights to examine environmental issues and weight impacts. We also looked at segmentations of flights to investigate the energy used in each type of flight.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Drone flight visible images, digital elevation maps, and geotiffs, Teller, Seward Peninsula, Alaska, USA, July 2017

Remote sensing data collected from Lawrence Berkeley National Laboratory’s (LBNL) unmanned aerial system (UAS) quadcopter platform – Inspire-1 – operated by the Ameriflux Management Project (ameriflux.lbl.gov) Technical Team. The Insprire-1 is a visible imagery UAS platform that simultaneously measures very high spatial resolution optical red/green/blue (RGB) at regular intervals along the flight path. This package includes data from a flight path over the NGEE Arctic Teller Site, west of mile marker 27 Bob Blodgett Highway in the Seward Peninsula, Alaska in July 2017. Derived image products include ortho-mosaiced RGB, an RGB-based digital surface model (DSM) using the structure from motion (SfM) technique, and a digital terrain model (DTM). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included. Unprocessed and processed data products are included in this package (processing levels 0-2). This metadata document contains flight campaign, instrument and file metadata, along with a description of data processing levels, data products and file naming scheme.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Drone flight visible images, digital elevation maps, and geotiffs, Kougarok, Seward Peninsula, Alaska, USA, July 2017

Remote sensing data collected from Lawrence Berkeley National Laboratory’s (LBNL) unmanned aerial system (UAS) quadcopter platform – Inspire-1 – operated by the Ameriflux Management Project (ameriflux.lbl.gov) Technical Team. The Insprire-1 is a visible imagery UAS platform that simultaneously measures very high spatial resolution optical red/green/blue (RGB) at regular intervals along each flight path. This package includes data from four flight paths over the NGEE Arctic Kougarok Site, west of mile marker 64 on Kuzitrin Road in the Seward Peninsula, Alaska in July 2017. Derived image products include ortho-mosaiced RGB, an RGB-based digital surface model (DSM) using the structure from motion (SfM) technique, and a digital terrain model (DTM). Ancillary aircraft data, flight mission parameters, and general flight conditions are also included. Unprocessed and processed data products are included in this package (processing levels 0-2). This metadata document contains flight campaign, instrument and file metadata, along with a description of data processing levels, data products and file naming scheme.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic) was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy’s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy’s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Report on ISR-1 High-Altitude Balloon Flight

To test small technologies at lower cost for space science applications, LANL has developed a small high altitude balloon payload that could, in the future, be regularly and inexpensively launched from LANL. A neutron detector, NEMO, was integrated to evaluate its performance in a space-like mixed-radiation environment and collect neutron data in the atmosphere. In collaboration with EES-14, a high-altitude balloon payload was launched from LANL Technical Area 51 on February 27, 2023 and April 17, 2023. For real-time geolocation, a SAM-M8Q M8 GNSS module was used to get position and time, and an Iridium RockBLOCK 9603 was used to communicate with the ground using the Iridium satellite fleet. These modules were all controlled using an Iteaduino Mega microcontroller board. Finally, a High Altitude Science Eagle Flight Computer with a temperature pressure sensor ran independently, writing data to an SD card. All of these modules were powered by a 5 mAh lithium polymer battery. The battery was attached to the bottom of the payload while the remaining electronics were embedded in the underside of the top of the payload. These modules were wired as seen in Figure 1-2. The Iteaduino Mega microcontroller board was programmed to use the RockBLOCK to send a message once every 10 minutes containing neutron and GPS data read off the NEMO and SAM M8Q, respectively. Once the message send attempt finished, the RockBLOCK would be slept for the rest of the 10 minute interval. The Eagle Flight Computer ran continuously throughout the flight, taking data every 6 seconds. The RockBLOCK message data was set up to be delivered from the Iridium satellite fleet to a website, where it was stored and parsed to create live maps and plots for analysis and balloon retrieval. The RockBLOCK message data was additionally configured to be sent to an email as a fail-safe. The payload was ground-tested successfully for over 50 hours, with multiple revisions occurring to best prepare for conditions at altitude and improve the software and firmware to fix any issues that cropped up with the data pipeline. Additional to the balloon payload, the flight had an attached iMet-4 radiosonde and Garmin T5 GPS Dog Collar. The radiosonde provided GPS and meteorological data. The T5 dog collar is used along with a Garmin Astro 430 to track the balloon at a range of up to 9 miles for retrieval. The balloon itself was initially a 1600 g meteorological balloon with an attached High Altitude Science parachute, both of which can be seen in Figure 1-3. After the first flight, the EES team swapped to a Rocketman parachute.

42 ENGINEERING↗
NASA NTRS1963

FLIGHT EXPERIENCES IN THE MERCURY PROGRAM

At this time, the National Aeronautics and Space Administration (NASA) has successfully completed five manned space flights in Project Mercury. Two of these were suborbital, and of approximately 19 minutes duration, and each of these subjected the pilot to about 5 minutes of weightlessness. The remaining three manned flights were orbital. Two of these flights involved the completion of three orbital passes, or about hours of weightlessness. The last orbital flight was extended to six orbital passes with nearly 10 hours of weightlessness. As a result of these flights, we have gained a wealth of information about space and man's ability to function in this new environment. There is, however, much which is yet to be learned regarding both of these aspects.

MERCURY PROJECT↗
NASA NTRS1970

Flight test results pertaining to the space shuttlecraft Symposium papers

This compilation consists of papers presented at the NASA Symposium on Flight Test Results Pertaining to the Space Shuttlecraft, held at the NASA Flight Research Center, Edwards, Calif., on June 30, 1970. The symposium was divided into the following sessions. I. Lifting Body Flight Test Results and II. Additional Space Shuttle Oriented Studies. Papers were presented by representatives from the NASA Flight Research Center and the U. S. Air Force Flight Test Center. A list of attendees is included.

Source record↗
NASA NTRS1971

Flight-determined aerodynamic stability and control derivatives of the M2-F2 lifting body vehicle at subsonic speeds

Aerodynamic derivatives were obtained for the M2-F2 lifting body flight vehicle in the subsonic flight region between Mach numbers of 0.41 and 0.64 and altitudes of 7000 feet to 45,000 feet. The derivatives were determined by a flight time history curve-fitting process utilizing a hybrid computer. The flight-determined derivatives are compared with wind-tunnel and predicted values. Modal-response characteristics, calculated from the flight derivatives, are presented.

Kempel, R. W.↗
NASA NTRS1971

Mission definition study for Stanford relativity satellite. Volume 2: Engineering flight test program

The need is examined for orbital flight tests of gyroscope, dewar, and other components, in order to reduce the technical and financial risk in performing the relativity experiment. A program is described that would generate engineering data to permit prediction of final performance. Two flight tests are recommended. The first flight would test a dewar smaller than that required for the final flight, but of size and form sufficient to allow extrapolation to the final design. The second flight would use the same dewar design to carry a set of three gyroscopes, which would be evaluated for spinup and drift characteristics for a period of a month or more. A proportional gas control system using boiloff helium gas from the dewar, and having the ability to prevent sloshing of liquid helium, would also be tested.

Source record↗
NASA NTRS1972

Flight program language requirements. Volume 1: Executive summary

The activities and results of a study for the definition of flight program language requirements are described. A set of detailed requirements are presented for a language capable of supporting onboard application programming for the Marshall Space Flight Center's anticipated future activities in the decade of 1975-85. These requirements are based, in part, on the evaluation of existing flight programming language designs to determine the applicability of these designs to flight programming activities which are anticipated. The coding of benchmark problems in the selected programming languages is discussed. These benchmarks are in the form of program kernels selected from existing flight programs. This approach was taken to insure that the results of the study would reflect state of the art language capabilities, as well as to determine whether an existing language design should be selected for adaptation.

Source record↗
NASA NTRS1972

Ground and flight test methods for determining limit cycle and structural resonance characteristics of aircraft stability augmentation systems

Performance criteria and test techniques are applied to stability augmentation systems (SAS) during ground testing to predict objectionable limit cycles and preclude structural resonance during flight. Factors that give rise to these problems, means of suppressing their effects, trade-offs to be considered, and ground test methods that have been developed are discussed. SAS performance predicted on the basis of these tests is compared with flight data obtained from three lifting body vehicles and the X-15 research airplane. Limit cycle and structural resonance test criteria, based upon ground and flight experience and data, were successfully applied to these vehicles. The criteria used were: The limit cycle amplitude (SAS gain multiplied by peak-to-peak angular rate) shall not exceed 0.5 deg for the highest product of control power and SAS gain that will be used in flight; the maximum in-flight SAS gain should never exceed 50 percent of the value at which a structural resonance can be sustained during ground test.

Painter, W. D.↗
NASA NTRS1972

Flight-determined derivatives and dynamic characteristics for the HL-10 lifting body vehicle at subsonic and transonic Mach numbers

The HL-10 lifting body stability and control derivatives were determined by using an analog-matching technique and compared with derivatives obtained from wind-tunnel results. The flight derivatives were determined as a function of angle of attack for a subsonic configuration at Mach 0.7 and for a transonic configuration at Mach 0.7, 0.9, and 1.2. At an angle of attack of 14 deg, data were obtained for a Mach number range from 0.6 to 1.4. The flight and wind-tunnel derivatives were in general agreement, with the possible exception of the longitudinal and lateral damping derivatives. Some differences were noted between the vehicle dynamic response characteristics calculated from flight-determined derivatives and those predicted by the wind-tunnel results. However, the only difference the pilots noted between the response of the vehicle in flight and the response of a simulator programed with wind-tunnel-predicted data was that the damping generally was higher in the flight vehicle.

Strutz, L. W.↗
NASA NTRS1972

Flight and ground tests of a very low density elastomeric ablative material

A very low density ablative material, a silicone-phenolic composite, was flight tested on a recoverable spacecraft launched by a Pacemaker vehicle system; and, in addition, it was tested in an arc heated wind tunnel at three conditions which encompassed most of the reentry heating conditions of the flight tests. The material was composed, by weight, of 71 percent phenolic spheres, 22.8 percent silicone resin, 2.2 percent catalyst, and 4 percent silica fibers. The tests were conducted to evaluate the ablator performance in both arc tunnel and flight tests and to determine the predictability of the albator performance by using computed results from an existing one-dimensional numerical analysis. The flight tested ablator experienced only moderate surface recession and retained a smooth surface except for isolated areas where the char was completely removed, probably following reentry and prior to or during recovery. Analytical results show good agreement between arc tunnel and flight test results. The thermophysical properties used in the analysis are tabulated.

Olsen, G. C.↗
NASA NTRS1972

Analysis of flight test transition and turbulent heating data. Part 1: Boundary layer transition results

The objective of the study was to provide a detailed post flight evaluation of ballistic vehicle flight test boundary layer transition data. A total of fifty-five vehicles were selected for analysis. These vehicles were chosen from a data sampling of roughly two hundred flights and the criteria for vehicle selection is delineated herein. The results of the analysis indicate that frustum transition of re-entry vehicles appears to be nose tip dominated. Frustum related parameters and materials apparently have a second order effect on transition. This implies that local viscous parameters on the frustum should not correlate flight test transition data, and in fact they do not. Specific parameters relative to the nose tip have been identified as the apparent dominant factors that characterize the transition phenomena and a correlation of flight test data is presented.

Martellucci, A.↗
NASA NTRS1972

Results of the 1970 balloon flight solar cell standardization program

For the eighth consective year, high-altitude calibration of solar cells was accomplished with the aid of free-flight balloons. Flights were conducted to an altitude of 36,576 m which is above 99.5% of earth's atmosphere where all water vapor levels and significant ozone bands are absent. Solar cells calibrated in this manner are significant used as intensity references in solar simulators and in terrestrial sunlight. Discussed is the method employed for high altitude balloon flight solar cell calibration. Also presented are data collected on 52 standard solar cells on two flights conducted in 1970. Solar cells flown repeatedly on successive flights have shown correlation of better than + or - 1.0%.

Greenwood, R. F.↗
NASA NTRS1973

Modeling of airplane performance from flight-test results and validation with an F-104G airplane

A technique of defining an accurate performance model of an airplane from limited flight-test data and predicted aerodynamic and propulsion system characteristics is developed. With the modeling technique, flight-test data from level accelerations are used to define a 1g performance model for the entire flight envelope of an F-104G airplane. The performance model is defined in terms of the thrust and drag of the airplane and can be varied with changes in ambient temperature or airplane weight. The model predicts the performance of the airplane within 5 percent of the measured flight-test data. The modeling technique could substantially reduce the time required for performance flight testing and produce a clear definition of the thrust and drag characteristics of an airplane.

Marshall, R. T.↗