Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “path integrals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

UAS Integration in the NAS Project: Overview of Flight Test Series 6

The National Aeronautics and Space Administration (NASA) Unmanned Aircraft Systems Integration in the National Airspace System (UAS-NAS) Project has conducted a series of flight test campaigns intended to support the reduction of barriers that prevent unmanned aircraft from flying without the required waivers from the Federal Aviation Administration (FAA). The 2019 Flight Test Series 6 (FT6) campaign furthered this path and supported three test configurations: 1) Radar Characterization, 2) Scripted Encounters and 3) Full Mission. Radar Characterization assessed the performance of Honeywell’s low size, weight, and power (low SWaP) radar system; Scripted Encounters investigated the timing of Detect and Avoid (DAA) alerting thresholds using a Department of Defense (DoD) Group 3 unmanned aircraft system (UAS) equipped with low SWaP sensors and three different live intruder aircraft flown at varying encounter geometries; and Full Mission validated human-in-the-loop simulations by collecting pilot performance data from a ground control station while controlling a live unmanned aircraft on a mission in both virtual and live air traffic controlled airspace. The subject pilot observed a research display that presented DAA advisories to maintain separation from live and virtual aircraft. The test was conducted over a twenty-week period within the R-2508 special use airspace located near Edwards Air Force Base (EAFB), CA. Over 240 encounters were flown during the test series and FT6 proved to be invaluable for the purposes of planning, managing, and executing this type of integrated flight test in both live and virtual environments. Data collected from FT6 was provided to the RTCA Special Committee 228 (SC-228) to help inform the Phase 2 Minimum Operational Performance Standards (MOPS). FT6 was the final test series for the UAS-NAS project that began in 2012. This paper provides an overview of FT6 and its success can be directly attributed to the diligent work of the men and women who supported this effort.

UAS in the NAS↗
DOE OSTI2020

Integration of Kokkos into MonteRay [Slides]

Monte Carlo Neutron Transport codes are C++-based and simulate interaction of nuclear particles with materials. MonteRay is a library for accelerating Monte Carlo ray-casting tallies with GPUs. Kokkos is commonly used to write performance portable applications for HPC platforms. A goal is to implement Kokkos into the Expected Path Length file that uses Cuda as a backend. The methodology and results are summarized.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Designing Moderately‐Solvating Electrolytes for High‐Performance Lithium–Sulfur Batteries

New electrolytes are critical for high‐energy lithium (Li)–sulfur (S) batteries (LSBs) to ensure their stability against Li metal anode and polysulfides (PSs) shuttling which hinder the large‐scale application of LSBs. In this study, the design principle of moderately solvating electrolytes (MSEs) for LSBs is demonstrated by using a multiple‐solvent system comprising of a highly solvating solvent, a weakly solvating solvent, and a non‐solvating solvent to create a well‐balanced electrolyte system. This resulting electrolyte significantly improves the cycle life of LSBs, achieving 300 cycles, which is twice as long as that of similar cells with the conventional electrolyte and it also ensures stable calendar life for at least seven months. The optimal MSE forms robust passivation layers enhancing the structural integrity of both S and Li metal electrodes after cycling. These virtues effectively hinder parasitic side reactions and self‐discharge behavior of LSBs. This electrolyte design principle is versatile and can be applied to other battery chemistries, providing a potential path toward the development of a more efficient and stable battery system. By addressing key challenges such as the instability of electrodes and shuttling of polysulfides, this electrolyte approach offers promising solutions for advancing LSB technology.

25 ENERGY STORAGE↗
DOE OSTI2025

Translocation mechanism of xeroderma pigmentosum group D protein on single-stranded DNA and genetic disease etiology

Abstract XPD is a key nucleotide excision repair (NER) protein whose function is vital for genome integrity. During NER, XPD serves as a 5′−3′ single-strand DNA translocase that enables lesion scanning and verification in genomic DNA. Yet, its translocation mechanism is incompletely understood. Here we use molecular simulations and chain-of-replicas path optimization methods to model the ATP-driven translocation mechanisms of XPD and its bacterial homolog DinG, revealing all on-path metastable intermediates and corresponding kinetic rates. We identify the XPD(DinG) global domain motions that modulate the strength of DNA association at the opposing ends of the DNA-binding groove. During the ATP hydrolysis cycle, alternating weak and strong interactions at two defined groove constrictions enable DNA reptation and forward displacement of the ATPase. Moreover, we show that DNA- or ATP-binding residues directly involved in translocation are hotspots for genetic disease mutations. Thus, our findings shed light on the etiology of XPD-associated genetic syndromes.

Paul, Tanmoy↗
DOE OSTI2026

The MuFusE large-volume diamond anvil cell for exploring muon-catalyzed fusion at higher pressures and temperatures

A new large-volume diamond anvil cell (DAC) has been developed for the Muon-catalyzed Fusion (μCF) Experiment (MuFusE), enabling the compression and heating of deuterium–tritium (d–t) mixtures to pressures and temperatures needed to advance μCF research. The MuFusE DAC achieves the large sample volumes necessary for high-precision fusion measurements while integrating cryogenic loading, all-metal sealing, and flexible bellows to maintain a secure environment during cell compression. Combined with remote pneumatic actuation and secondary containment, the DAC safely managed a 25 Ci tritium inventory while providing a clear optical path for in situ measurements of sample pressure and composition via laser spectroscopy. Utilizing 5 mm diameter diamond anvils oriented in the path of a high-intensity muon beam, the apparatus achieved a stable sample volume of 19.2 mm 3 at liquid density, pressures up to 933 MPa and temperatures up to 400 K—benchmarks that significantly exceed previously reported limits for static d–t targets.

Kalow, J. D. [Acceleron Fusion, Inc., Cambridge, M↗
DOE OSTI2023

Computational Materials Design for Ceramic Nuclear Waste Forms Using Machine Learning, First-Principles Calculations, and Kinetics Rate Theory

Ceramic waste forms are designed to immobilize radionuclides for permanent disposal in geological repositories. One of the principal criteria for the effective incorporation of waste elements is their compatibility with the host material. In terms of performance under environmental conditions, the resistance of the waste forms to degradation over long periods of time is a critical concern when they are exposed to natural environments. Due to their unique crystallographic features and behavior in nature environment as exemplified by their natural analogues, ceramic waste forms are capable of incorporating problematic nuclear waste elements while showing promising chemical durability in aqueous environments. Recent studies of apatite- and hollandite-structured waste forms demonstrated an approach that can predict the compositions of ceramic waste forms and their long-term dissolution rate by a combination of computational techniques including machine learning, first-principles thermodynamics calculations, and modeling using kinetic rate equations based on critical laboratory experiments. By integrating the predictions of elemental incorporation and degradation kinetics in a holistic framework, the approach could be promising for the design of advanced ceramic waste forms with optimized incorporation capacity and environmental degradation performance. Such an approach could provide a path for accelerated ceramic waste form development and performance prediction for problematic nuclear waste elements.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1976

Flux-flow voltages during guided flux collapse from hollow superconducting cylinders

Voltages across diametrically opposite contact pairs on the outer surface of superconducting Nb tubes are found to depend dramatically upon the spatial configuration of the voltage-measuring leads relative to the positions of the moving magnetic flux lines. Experiments have been conducted to study these voltages for different wall thicknesses and for a variety of arrangements of the leads when flux in the hole and the wall of the Nb tube is made to exit or enter, completely or partially, by applying heat at a narrow strip along its length. Using the critical-state concept, a model for the change of flux and the resulting electric fields in the Nb tube on application of a heat pulse is presented. The resulting time-dependent and time-integrated voltages are calculated in excellent quantitative agreement with the experimental results. These results show that the flux-flow voltages across two contact points on a superconductor arise from the generation of an induced electric field over a chosen path in the superconductor between the contact points and from a change of magnetic flux through the surface bounded by the measuring leads and the chosen path in the superconductor.

Khanna, S. M.↗
NASA NTRS1979

Evaluation of a Brayton cycle recuperator after 21,000 hours of ground testing

A metallographic examination was conducted on a Brayton cycle recuperator and associated ducting after 21,000 hours of ground testing in air. At the hot (turbine) end, the recuperator operated at a nominal temperature of 675 C. The type 347 stainless-steel recuperator performed satisfactorily in the ground test even though the primary working fluid leaked to the atmosphere periodically. The leakage path was located at plate-bar braze joints which cracked as a result of thermal stresses. The welded type 347 stainless steel ducting a type 347/Hastelloy X bellows survived the ground test with no apparent loss of ductility or integrity. Some apparent aging embrittlement was observed in the Hastelloy X ducting but the serviceability was not affected.

Moore, T. J.↗
NASA NTRS1986

NASA B737 flight test results of the Total Energy Control System

The Total Energy Control System was developed and tested in September 1985 during five flights on the NASA Langley Transport System Research Vehicle, a modified Boeing B737. In the system, the total kinetic and potential energy of the aircraft is controlled by the throttles, and the energy distribution is controlled by the elevator. A common inner loop is used for each mode of the autopilot, and all the control functions of a conventional pitch autopilot and autothrottle are integrated into a single generalized control concept, providing decoupled flightpath and maneuver control, and a coordinated throttle response for all maneuvers. No instabilities or design problems requiring gain adjustment in flight were found, and comparison with simulation results showed excellent path tracking.

Bruce, K. R.↗
NASA NTRS1987

Force and moment rotordynamic coefficients for pump-impeller shroud surfaces

Governing equations of motion are derived for a bulk-flow model of the leakage path between an impeller shroud and a pump housing. The governing equations consist of a path-momentum, a circumferential - momentum, and a continuity equation. The fluid annulus between the impeller shroud and pump housing is assumed to be circumferentially symmetric when the impeller is centered; i.e., the clearance can vary along the pump axis but does not vary in the circumferential direction. A perturbation expansion of the governing equations in the eccentricity ratio yields a set of zeroth and first-order governing equations. The zeroth-order equations define the leaking rate and the circumferential and path velocity distributions and pressure distributions for a centered impeller position. The first-order equations define the perturbations in the velocity and pressure distributions due to either a radial-displacement perturbation or a tilt perturbation of the impeller. Integration of the perturbed pressure and shear-stress distribution acting on the rotor yields the reaction forces and moments acting on the impeller face.

Childs, Dara W.↗
NASA NTRS1993

Mixed voltage VLSI design

A technique for minimizing the power dissipated in a Very Large Scale Integration (VLSI) chip by lowering the operating voltage without any significant penalty in the chip throughput even though low voltage operation results in slower circuits. Since the overall throughput of a VLSI chip depends on the speed of the critical path(s) in the chip, it may be possible to sustain the throughput rates attained at higher voltages by operating the circuits in the critical path(s) with a high voltage while operating the other circuits with a lower voltage to minimize the power dissipation. The interface between the gates which operate at different voltages is crucial for low power dissipation since the interface may possibly have high static current dissipation thus negating the gains of the low voltage operation. The design of a voltage level translator which does the interface between the low voltage and high voltage circuits without any significant static dissipation is presented. Then, the results of the mixed voltage design using a greedy algorithm on three chips for various operating voltages are presented.

Panwar, Ramesh↗
NASA NTRS1998

The Role of Computational Fluid Dynamics at Marshall Space Flight Center

The Marshall Space Flight Center (MSFC) is the Center of Excellence for Space Propulsion Technology within NASA. One of MSFC's goals is to lower the cost of access to space. MSFC's Fluid Dynamics Division, a part of the Structures and Dynamics Lab, assists in accomplishing this goal. This division is divided into two branches: experimental and analytical, whose work is complimentary and integrated. In the analysis branch, the emphasis is to apply, rather than develop computational fluid dynamics (CFD), to reduce the cost of design and development of: (1) pump and turbine feedlines and feed manifolds; (2) all primary and secondary flow paths in pumps; (3) all primary and secondary flow paths in turbines; (4) combustion chambers; (5) rocket engine nozzles and plumes; and (6) launch vehicles ascent. The broad range of applications imposes unique constraints on the software. The use of CFD in evaluating rocket engine hardware, specifically, is of value due to several reasons: (1) Rocket engine hardware is extremely expensive to build and test; (2) high engineering and development cost is due to limited production; (3) the cost of one engine test is greater than the average yearly hardware and software cost; (4) CFD represents a relatively small investment relative to the impact it has on the engine development; and (5) computing costs are continuously decreasing. In terms of accuracy the predictable error is more useful than the inconsistent accuracy. The achievable accuracy varies from application to application. The lack of accuracy is often caused by improper analyses: such as improperly applied or located boundary conditions, or attempting steady analysis of unsteady flows. This report is in viewgraph format.

Garcia, Roberto↗
NASA NTRS2007

NIRSS Upgrades: Final Report

This year we were able to further the NIRSS program by re-writing the data ingest and display code from LabVIEW to C++ and Java. This was leveraged by a University of Colorado Computer Science Department Senior Project. The upgrade made the display more portable and upgradeable. Comparisons with research aircraft flights conducted during AIRS-2 were also done and demonstrate reasonable skill in determining cloud altitudes and liquid water distribution. Improvements can still be made to the cloud and liquid logic. The icing hazard index was not evaluated here since that represents work in progress and needs to be made compatible with the new CIP-Severity algorithm. CIP is the Current Icing Potential product that uses a combination decision tree/fuzzy logic algorithm to combine numerical weather model output with operational sensor data (NEXRAD, GOES, METARs and voice pilot reports) to produce an hourly icing diagnosis across the CONUS. The new severity algorithm seeks to diagnose liquid water production through rising, cooling air, and depletion by ice processes. The information used by CIP is very different from that ingested by NIRSS but some common ground does exist. Additionally, the role of NIRSS and the information it both needs and provides needs to be determined in context of the Next Generation Air Traffic System (NGATS). The Weather Integrated Products Team has a plan for an Initial Operating Capability (IOC) to take place in 2012. NIRSS is not explicitly a part of that IOC but should be considered as a follow-on as part of the development path to a 2025 full capability.

Politovich, Marcia K.↗
DOE OSTI2020

Waste Management Project Success - Regulatory Assurance Systems - 20118

Waste management (WM) and remediation projects are essential within a restorative environmental culture. Despite years of experience, challenges and obstacles associated with efficient and effective WM project execution remain. Although some obstacles are project specific, a common challenge is navigating the regulatory landscape from planning through execution, particularly with first of a kind (FOAK) and first in a while (FIAW) projects. The absence of a comprehensive regulatory assurance strategy places significant hurdles in the path of project success. To clear a path for the successful execution of increasingly complex WM projects, this paper focuses on development of a comprehensive regulatory assurance strategy and implementation plan that effectively engages stakeholders, agencies, and performers to produce project plans that fully and cost effectively integrate applicable regulatory requirements. The most reliable way to align regulatory processes and decisions needed for mission success is through a regulatory assurance system. This system establishes a healthy interface with regulatory decision makers, to work in a collaborative manner, to create a common vision for regulatory decisions on an agreed upon schedule. A regulatory assurance system consists of several elements. Although the mission may vary from cleanup to site closure to nuclear component production, the elements of a regulatory assurance system remain essentially constant and must include: 1) identifying a common vision or end state, 2) developing a long-term, integrated strategy and schedule, 3) establishing a regulatory partnering team consisting of key decision-makers, 4) regular and frequent communication with decision-makers, 5) ensuring consistent surveillance for early identification of issues and changes that may impact the project, 6) quick resolution of emerging issues to prevent schedule impact, 7) identifying core compliance functions, 8) periodically assessing progress of the project as it relates to regulatory assurance and, 9) providing constructive feedback to improve the process. A regulatory assurance system provides a living, multi-faceted approach to planning, visioning, communicating and tracking to avoid surprises and ensure smooth and timely progress to the project. The overall success measures will be whether the system produces common sense regulatory decisions supporting the vision on time without appeal. Effective regulatory frameworks rarely happen on their own. Balanced, common-sense regulatory decisions stem from teams that are trained to work together to achieve shared goals. In this paper, particular attention is placed on the importance of starting with a shared vision for a regulatory assurance and execution strategy that leverages experience to establish optimal approaches. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Nitrogen derived from Combined Algal Processing supports algae cultivation for biofuels

Algae biomass, a biofuel feedstock with potential to reduce global CO 2 emissions, is currently too expensive Nitrogen, a significant input and life cycle cost, requires research on recycling and additional sources to reduce costs. Integral to nitrogen recycling is the knowledge of actual nitrogen requirements in outdoor ponds, thus data from the Unified Field Studies of the Algae Testbed Public-Private Partnership was analyzed. The data showed that Nannochloropsis oceanica used 14–24 mg/L NH 4 + per harvest cycle for robust growth. Nitrogen recycled directly from the algae conversion process will likely be the primary source of nitrogen for algae cultivation. Harvested algae can be fractionated via Combined Algal Processing (CAP), where algae are pretreated, fermented, and the fuel feedstocks (e. g. ethanol, lipids) are removed leaving a nitrogen rich slurry. Chlorella vulgaris grew robustly in nitrogen-free media supplemented with CAP residues through 4 harvest cycles with no inhibition. The amount of nitrogen as free ammonium available for recycling directly without further processing was insufficient (~4% of total needed), thus the nitrogen fixing bacteria, Azotobacter vinelandii, was investigated as a means for increasing ammonium concentration in CAP residues. This organism was shown to be proficient at growth on sugars liberated from algae biomass during pretreatment and sustained algae growth using A. vinelandii supernatants was also demonstrated. Using Azotobacter to increase ammonium concentrations on-site using an inexpensive biological process to generate the necessary ammonium for outdoor algae cultivation improves sustainability of algae biofuels by avoiding the energy intensive steps of typical ammonium production and transport. Furthermore, these results show that byproducts of algae conversion begin to close nitrogen demand and, with further supplementation by diazotrophic bacteria or protein hydrolysis, may completely replace current energyintensive and costly industrial nitrogen sources offering a path to increased economic feasibility and improved life cycle analysis of algae-based biofuels.

09 BIOMASS FUELS↗
DOE OSTI2023

Preliminary Design of Critical Experiments Involving Commercially Available B 4 C Neutron Absorber Plates with Low-Enriched UO 2 Fuel [Slides]

Conclusions of this presentation conclude that the experiment is feasible with at least 10 critical configurations, and low expected benchmark uncertainty. Potential high impact for the understanding of commercially used neutron absorber plates. Next steps are to think about other configurations: rod pitch, other rods – Finalize plate support, uncertainty study. Additionally, the potential use of IER-441 central test region to safely place the plate in the core. Next steps include the Determination of the neutron absorber plate characterization path and the Potential SINBAD benchmark of neutron transmission measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

A novel approach for adaptive skeleton toolpath generation

Industry 4.0 is revolutionizing manufacturing through the integration of automation and real-time data sharing in cyber-physical systems. At the forefront of this revolution is large-format additive manufacturing. In large-format printing, parts are often designed to be an even number of beads wide to produce a completely dense part. However, voids can still arise. This is often due to the part not being an even number of bead widths wide in some areas, or in geometry containing acute angles, as the process of generating closed contours cannot completely fill the space. Voids can be tolerated in smaller models, but in large-format additive manufacturing they may cause mechanical defects. To fill these voids, open loop paths called skeletons are often used, but they are typically limited by the physical constraints defined in the slicing software. To address this, researchers at Oak Ridge National Laboratory have extended skeleton toolpaths via an adaptive methodology. These adaptive skeletons were found to better fill void spaces through manipulation of physical parameters of the build process and were calculated as part of the slicing process.

42 ENGINEERING↗
DOE OSTI2024

Model Diagnostics for Equation Oriented Models: Roadblocks and the Path Forward

This poster was presented at the Foundations of Computer Aided Process Design (FOCAPD) 2024 conference with a paper describing efforts to develop a unified workflow and toolbox for diagnosing issues in equation-oriented models as part of the IDAES modeling framework. The poster presents the work currently underway within the IDAES project to develop and integrate cutting edge model analysis techniques into a common toolbox and workflow for model developers to use.

Lee, Andrew↗