Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “excel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Titanium porous-transport layers for PEM water electrolysis prepared by tape casting

While the porous-transport layer (PTL) is a key component in PEM electrolyzers, it is one of the most underexplored due to limited available structures. In this work, we present a novel PTL design for PEM water electrolyzers enabled by a cost-effective, scalable tape-casting technique. Here, a precise control of the PTL pore structure is achieved by incorporating poreformers of various sizes, and by varying the titanium and poreformer ratio. The structures are characterized with SEM and synchrotron X-ray computed tomography imaging techniques. Comprehensive electrochemical performance analysis demonstrates that higher titanium loading provides improved contact at the catalyst-layer/PTL interface but suffers from severe mass-transport losses due to gas bubbles. We solve this mass-transport problem by mixing in large poreformer beads that produce a highly porous structure with excellent gas removal properties yet still maintaining mechanical integrity. The PTL fabricated with 60:40 Ti:PMMA ratio and 60 μm PMMA bead size outperformed the standard commercial Ti powder-based PTL by 62 mV at 4 A/cm 2 .

25 ENERGY STORAGE↗
DOE OSTI2023

Reversible solid oxide cells: Early performance and microstructural evolution during electrolysis and switched mode operation

Incorporating more renewables into our energy mix will require a diversity of technological solutions. Reversible solid oxide cell systems (RSOCs) operating reversibly between fuel cell and electrolysis modes with high round-trip efficiencies offer one such solution. However, questions remain about the stability of the oxygen and fuel electrodes under reversible operation. Here, in this study, single cells with the configuration Ni-YSZ|YSZ|GDC10|NNO-NDC50|NNO are operated by reversible cycling under potentiostatic conditions. Test conditions are chosen to be representative of average stack conditions that are likely to be encountered during operation of a stack constructed of such cells. The results of reversible cycling over 500 h (21 cycles) are compared with operating the cells under potentiostatic conditions in the electrolysis-only mode (i.e., without cycling). Voltage-current density (DC), AC complex impedance spectroscopy, distribution of relaxation times (DRT) analysis, and scanning electron microscopy (SEM) indicate excellent reversibility and stability of the neodymium nickelate-based oxygen electrodes in both electrolysis and reversible cycling modes. Degradation behavior is attributed to the loss and coarsening of connected Ni particles in the fuel electrode, particularly in the active layer. However, reversible operation mitigates this degradation compared to operation in the electrolysis-only (SOEC-only) mode.

25 ENERGY STORAGE↗
DOE OSTI2023

A hybrid analytical and numerical model for cross-over and performance decay in a unit cell vanadium redox flow battery

Developing an accurate and efficient model for cross-over is critical for improving the long-term performance of redox flow batteries (RFBs). Here, this work presents a hybrid analytical and numerical model that combines a two-dimensional analytical solution to the active species, a one-dimensional analytical model for cross-over mechanisms, and a zero-dimensional numerical model for outlet concentrations of reactants. By comparing with experiment over 41 cycles (ca. 144 h), the model reported a mean voltage difference of 0.0089 V, mean time difference of 14 s per cycle (of 3.5 h), maximum relative difference for capacity and energy of 1.34% and 1.63%, respectively. The predicted mean concentrations for V 2+ , V 3+ , and VO$_{2}^{+}$ in membrane are 65%~77% of measured values from the literature. Upon validation, the model reproduced behaviors in electrolyte imbalance similar to those observed in experiments and numerical models, and revealed the control of cross-over, self-discharge, stoichiometry of side reactions, and Coulombic efficiency on electrolyte imbalance. The model also demonstrates excellent computational efficiency for simulating 41 cycles (around 37,000 points) within 3~4 s. The demonstrated efficiency and accuracy for predicting cross-over and its impacts on voltage, capacity&energy decay, membrane concentrations, and electrolyte imbalance makes it a reliable tool for optimizing RFBs’ long-term performance.

25 ENERGY STORAGE↗
DOE OSTI2024

Unraveling the conundrum of electronic leakage in protonic ceramic cells: Operation-specific insights and rational design strategies

Electronic conduction through proton-conducting electrolytes significantly impairs the efficiency of protonic ceramic cells (PCCs). Here, in this study, we explore the electron and ion mixed transport properties of four common protonic ceramics, BaZr 0.8 Y 0.2 O 3-δ (BZY82), BaZr 0.7 Ce 0.2 Y 0.1 O 3-δ (BZCY721), BaZr 04 Ce 0.4 Y 0.1 Yb 0.1 O 3-δ (BZCYYb4411), and BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ (BZCYYb1711). It marks the first instance of investigating these properties under operation-specific scenarios: fuel side of electrolysis cell, air side of electrolysis cell, fuel side of fuel cell, and air side of the fuel cell. BZCYYb1711 exhibits the highest ionic conductivity, but two to three times higher electronic leakage when exposed to oxygen-containing environments than the others. BZY82 exhibits approximately two times higher electronic leakage in a hydrogen-containing environment. BZCY721 demonstrates excellent ion transport numbers (~0.95) across these four operating conditions. BZCYYb4411 behaves quite similarly to BZCY721. The most challenging operating environment for all candidates is the air side of fuel cell mode. This mode leads to a high initial electronic leakage, followed by a significant increase with polarization. The probable cause for this behavior is a H 2 -free, polarization-induced reduction that leads to the formation of V$^•_O$. The electron small polaron associated with V$^•_O$ is released by the electrical field due to the Poole-Frenkel effect. ZnO and NiO sintering aids are found to be detrimental to the ionic conductivity of the electrolytes. In particular, NiO substantially lowers the ion transport number. The correlation of the operation-specific electronic leakage to full cells is discussed. It is suggested that a rational PCC design should synergistically couple BZCYYb1711 at fuel side with BZCY4411 at air side to deliver a well-balanced performance and faradaic efficiency simultaneously, and the high temperature sintering process with a NiO fuel electrode should be shortened or replaced by ultra-fast sintering techniques or using a fuel electrode scaffold-infiltration fabrication strategy.

42 ENGINEERING↗
DOE OSTI2024

Ultra-stable trimetallic phosphide heterostructure with regulated electronic structure for overall water splitting at high current densities

Developing ultra-stable electrocatalysts for highly efficient overall water splitting at high current density (HCD) is critical for renewable hydrogen/oxygen production in the industry. However, the most active electrocatalysts for large current-driven water splitting are seriously handicapped by insufficient electrical contact kinetics due to the intensive bubble overflow. Herein, we demonstrate the ultra-stable trimetallic phosphides of NiFeP/NiCoP catalysts on a hydrophilic Ni foam skeleton via a corrosion-hydrothermal-phosphating strategy. The optimized NiFeP/NiCoP catalyst stabilizes for 600 h at -1 A cm -2 for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in alkaline solution, and it only needs low overpotentials of 237 and 314 mV to drive HER and OER at 1 A cm -2 , respectively. As expected, the optimized NiFeP/NiCoP electrode maintains 1000 h at 0.5 A cm -2 for water splitting, ranking among the top performers among reported catalysts. Such excellent performance could be attributed to the fast electron transfer for electrochemical reactions, the electron-deficient Fe/Ni sites contribute to forming robust metal oxyhydroxide during OER, and electron-rich Co sites facilitate H adsorption during HER. In conclusion, the findings present a highly promising candidate for ultra-stable non-noble metal electrocatalysts, offering a viable option for hydrogen/oxygen supply for fuel cells and metal-air batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Optimization of catholyte for halide-based all-solid-state batteries

Halide solid electrolytes gain significant attention due to their high ionic conductivity, low processing temperature, dry air compatibility, and high-voltage stability. However, low cathode active material (CAM) loading in the composite cathode constrains the realization of high energy density for halide-based all-solid-state batteries. In this study, three halide materials, raw Li 3 YBrCl 5 (LYBC-R, <30μm), milled LYBC (LYBC-M, <5 μm) and freeze-dried Li 3 InCl 6 (LIC, <500 nm), were used as catholytes, combined with LYBC-M as the electrolyte and LiIn alloy as the anode. The CAM:catholyte ratio was investigated as well as stack pressure and operating temperature. Our study demonstrates that particle size of the catholyte plays an important role only for high CAM loading or high C-rate cycling. At moderate CAM loading (65 and 70wt% LiNi 0.83 Mn 0.06 Co 0.11 O 2 ) and 0.1 C-rate, all the three catholytes perform well, providing initial discharge capacities >177 mAh/g. At high CAM loading (85wt%) and 0.1 C-rate, a cathode with the nano-scale LIC catholyte provides discharge capacity of 175 mAh/g, while the larger particle size catholytes suffer significantly reduced capacity. Both LYBC and LIC catholytes provided capacity retention >80% after 200 cycles at 0.5C. These results imply that cathode particle size is critically important for performance at high CAM loading. Furthermore, both electrolyte and cathode were tape cast to scale up size and prepare realistic layer thicknesses. A small amount of binder was used in both layers, to balance the electrochemical performance and mechanical properties. Further, the discharge capacity of a tape cell was 152mA h/g at 0.1C with a capacity retention of 81.8% after 20 cycles at 0.5C. The results demonstrate the excellent performance of LYBC as an electrolyte, and provide guidance for halide-based cathode design.

25 ENERGY STORAGE↗
DOE OSTI2025

Vanadium-enhanced Na 2 FePO 4 F cathodes for high-performance sodium-ion batteries

Sodium fluorophosphate Na 2 FePO 4 F holds great potential for sodium-ion batteries due to its high theoretical capacity, excellent structural stability, abundant resources, and affordability. However, its poor electronic and ionic conductivities limit its practical applications. Therefore, ion doping and carbon coating have been employed as synergistic strategies in this study to overcome these limitations. A one-step, energy-efficient solid-state method using sucrose as a carbon coating source was used to synthesize Na 2 FePO 4 F/C (NFPF/C) and its doped variant, Na 2 Fe 0.85 V 0.1 PO 4 F/C (NFVPF/C). 23 Na-MAS-NMR spectra confirm the existence of two distinct sites for sodium (Na1/Na2). The ex-situ 23 Na-MAS-NMR performed at different states-of-charge reveals the activity of only one sodium. The scanning electron microscopy findings reveal a reduction in the particle size with V-introduction, enhancing the energetic performances. NFVPF/C delivers higher specific capacity of 122 mAh g −1 compared to 116 mAh g −1 for NFPF/C at 0.1C. It also demonstrates improved cycling stability, retaining 81 % of its initial capacity after 120 cycles, in contrast to 46 % for the pristine material. The doped phase outperforms the pristine at higher current rates, delivering specific capacities of 81 and 55 mAh g −1 at 2C and 3C, respectively, compared to 35 and 17 mAh g −1 for NFPF/C.

25 ENERGY STORAGE↗
DOE OSTI2026

Enhanced electrochemical performance and extended cycling of resorcinol-formaldehyde derived N-doped carbon xerogel for alkali metal-ion (Li/Na/K) batteries

Resorcinol formaldehyde-derived carbon xerogel (RFC) is a versatile material with tuneable properties, synthesized through a simple sol-gel method. This study presents nitrogen-doped RF carbon xerogel (N-RFC) with 11.8 at% nitrogen doping, offering a microporous architecture ideal for alkali metal-ion (Li, Na, K) batteries. The porous N-doped framework enhances electrochemical performance by improving ion transport, increasing active storage sites, and significantly boosting metal-ion adsorption, particularly through pyrrolic nitrogen, as revealed by first-principles calculations supported by XPS analysis. N-RFC anodes showed excellent cycling stability, high-capacity retention, and fast charge/discharge capabilities, rendering them suitable for commercial applications. Notably, the N-RFC anode demonstrates high-rate long-term cycling stability, retaining its capacity of 83.5 % (188 mAh/g at 2 C-rate) and 50 % (133 mAh/g at 1250 mA/g) over 1000 cycles for Li and Na-ion batteries, respectively, favorable for commercial battery applications. Additionally, N-RFC demonstrates a reversible capacity of 120 mAh/g after 394 cycles with a retention of 82 % for K-ion batteries. The ability of the material to accommodate larger ions like Na + and K + further emphasizes its versatility and potential application in diverse alkali metal-ion battery systems.

25 ENERGY STORAGE↗
DOE OSTI2026

Influence of aluminum source and Ni/Al ratio in a batch stirred tank reactor on the structure, morphology, and electrochemical performance of Ni-rich NMA cathodes

Here, the structural, morphological, and electrochemical performance of Ni-rich LiNi 0.9 Mn 0.05 Al 0.05 O 2 (955NMA) and LiNi 0.85 Mn 0.05 Al 0.1 O 2 (85,510) cathodes strongly depends on the properties of their hydroxide precursors. Ni-Mn-Al hydroxide precursors were synthesized through controlled co-precipitation in a batch stirred tank reactor, where pH, reaction time, metal-ion feed rate, aluminum source, and aluminum concentration were systematically varied to tailor particle morphology, phase composition, and dopant distribution. Two aluminum sources, aluminum nitrate and sodium aluminate produced two distinct hydroxide precursors NMA(OH) 2 -1 and NMA(OH) 2 -2, which were lithiated to form LiNMA1 (Li 0.992 [Ni 0.905 Mn 0.049 Al 0.046 ]O 2 ) and LiNMA2 (Li 0.990 [Ni 0.850 Mn 0.047 Al 0.103 ]O 2 ). Structural and compositional analyses revealed that aluminum incorporation and phase formation in Ni–Mn–Al hydroxides are governed by local supersaturation and interfacial growth kinetics. Rapid dilute aluminum addition produced aluminum-free β-phase hydroxides, intermediate conditions generated mixed α/β phases, whereas slow concentrated dosing enabled uniform aluminum incorporation and stabilization of the β-phase structure. LiNMA1 delivers a high initial discharge capacity of 223 mAhg −1 but significant capacity fading with 67% retention after 100 cycles, associated with structural instability. In contrast, LiNMA2 delivers a lower initial capacity 172 mAhg −1 yet excellent cycling stability 91% retention, attributed to improved TM–O framework stability and reduced cation disorder.

Capacity↗
DOE OSTI2026

Upcycling Polycrystalline LiNi1/3Mn1/3Co1/3O2 to High-Performance Large-Grained LiNi0.6Mn0.2Co0.2O2 via Simplified Polyol-Mediated Recycling

The escalating demand for lithium-ion batteries (LIBs) necessitates advanced recycling strategies that can address both resource scarcity and environmental impact. While conventional hydrometallurgy shows promise, it is challenged by complexity, impurity management, and environmental footprint. Here, we report a strategic polyol-metallurgy recycling process that efficiently transforms spent polycrystalline LiNi1/3Mn1/3Co1/3O2 (NMC111) into high-performance large-grained LiNi0.6Mn0.2Co0.2O2 (NMC622), offering dual benefits of compositional upcycling and morphology upgradation. Our approach leverages a polyol system with meticulous control over nickel salt addition and the precipitation process. This yields upcycled cathode materials possessing excellent structural integrity, well-defined large-grained particles (5-10?..mu..m), and robust electrochemical performance, including a specific capacity of ~182 mAh g-1 at C/10 and 88.0% capacity retention after 100 cycles. This facile and multifunctional process provides an environmental-friendly pathway for advanced cathode recycling, significantly contributing to a circular economy for LIBs through precise control over critical material attributes.

25 ENERGY STORAGE↗
DOE OSTI2020

Application of Koopman operator for model-based control of fracture propagation and proppant transport in hydraulic fracturing operation

This work explores the application of the recently developed Koopman operator approach for model identification and feedback control of a hydraulic fracturing process. Controlling fracture propagation and proppant transport with precision is a challenge due in large part to the difficulty of constructing approximate models that accurately capture the characteristic moving boundary and highly-coupled dynamics exhibited by the process. Koopman operator theory is particularly attractive here as it offers a way to explicitly construct linear representations for even highly nonlinear dynamics. The method is data-driven and relies on lifting the states to an infinite-dimensional space of functions called observables where the dynamics are governed by a linear Koopman operator. Here this work considers two problems: (a) fracture geometry control, and (b) proppant concentration control. In both cases, an approximate linear model of the corresponding dynamics is constructed and used to design a model predictive controller (MPC). The manuscript shows that in the case of highly nonlinear dynamics, as observed in the proppant concentration, use of canonical functions in the observable basis fails. In such cases, a priori system knowledge can be leveraged to choose the required basis. The numerical experiments demonstrate that the Koopman linear model shows excellent agreement with the real system and successfully achieves the desired target values maximizing the oil and gas productivity. Additionally, due to its linear structure, the Koopman models allow convex MPC formulations that avoid any issues associated with nonlinear optimization.

42 ENGINEERING↗
DOE OSTI2025

Low-lying states and total internal partition sums of CH

The electronic structure and spin-orbit states of the CH radical have been systematically investigated using multi-reference configuration interaction (MRCI) and single-reference coupled-cluster (CC) methods. These calculations were performed in conjunction with large correlation-consistent basis sets of quadruple-, quintuple-, and sextuple-ζ quality. To achieve high accuracy, electronic energies for all states were extrapolated to the complete basis set (CBS) limit, enabling the detailed construction of potential energy curves and determination of reliable spectroscopic constants. Spin-orbit coupling effects were explicitly incorporated, and vibrational energy levels were computed via Numerov analysis. Furthermore, the resulting values exhibit good to excellent agreement with available experimental data. Dipole moment and transition dipole moment curves were evaluated to assess the opacity characteristics of CH, revealing that transitions such as Χ 2 Π (u′′ = 0) → Α 2 Δ (u′ = 0), Χ 2 Π (u′′ = 0) → Β 2 Σ − (u′ = 0), Χ 2 Π (u′′ = 0) → C 2 Σ + (u′ = 0), and Χ 2 Π (u′′ = 0) → D 2 Σ + (u′ = 3) are particularly probable. Finally, the total internal partition function sum (TIPS) of CH was computed over a broad temperature range (10–30,000 K) based on our high-accuracy ab initio results.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Single crystal growth and characterization of new Zintl phase Ca 9 Zn 3.1 In 0.9 Sb 9

Complex Zintl phases have yielded a large variety of promising new thermoelectric materials. Here we report the discovery of the new Zintl phase Ca 9 (Zn 1– x In x ) 4 Sb 9 ( x ~ 0.9), needle-like crystals of which were serendipitously obtained from an In- and Sb-rich flux. Although its composition is reminiscent of Ca 9 Zn 4+ x Sb 9 , an excellent thermoelectric material with zT > 1, the substitution of In on the Zn site leads to the formation of an entirely new structure type. Single crystal X-ray diffraction revealed a structure characterized by T Sb 4 tetrahedra ( T = statistically disordered Zn and In atoms) and ZnSb 3 triangular units, which share common corners to form [ T 4 Sb 9 ] 18– polyanions. The average structure was found to have hexagonal symmetry. The valence electron count in this heavily-disordered structure appears to follows the Zintl-Klemm rules, suggesting semiconducting behavior. Single crystal electrical conductivity and Seebeck coefficient measurements support this conclusion, suggesting that the as-grown crystals are degenerate p -type semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Solution-processable copper(I) iodide-based inorganic-organic hybrid semiconductors composed of both coordinate and ionic bonds

Three new one-dimensional (1D) All-In-One (AIO) type CuI-based hybrid semiconductors with both dative and ionic bonds between the inorganic and organic components have been successfully designed and synthesized by using the ligands containing both cationic center and coordination available sites. Structural analysis confirms that all compounds share the same formula of Cu 4 I 6 (L) 2 (L = ligand) and are composed of 1D-Cu 4 I 6 2- anionic chains that coordinate to cationic ligands. Additionally, these materials demonstrate high stability towards heat and moisture and excellent solution processability due to their unique bonding nature. They emit low energy light ranging from green to orange color (530-590 nm). The origin and mechanism of their emissions were studied by both experimental and theoretical methods. More importantly, all compounds can be easily fabricated into films by solution process, a desired but rare feature for most of CuI-based hybrids built of extended networks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A small-box approach to the local crystal structure of Y 3 NbO 7

The local crystal structure of Y 3 NbO 7 was probed using neutron total scattering. Five different structural models were fit to the experimental pair distribution function of this material up to 15 Å. Fits of defect fluorite (Fm$\overline{3}$m), pyrochlore (Fd$\overline{3}$m), and orthorhombic C weberite models (C222 1 ) were attempted based on prior structural investigations of Y 3 NbO 7 and related fluorite-based materials. Orthorhombic P weberite (P222 1 ) and monoclinic weberite models (P112 1 ) were derived via symmetry reduction of the orthorhombic C weberite structure. All models except monoclinic weberite failed to reproduce the experimental pair distribution function. Misfits were clearly visible for peaks arising from atom pairs within the first coordination shell (defect fluorite and pyrochlore) and beyond (orthorhombic C and P weberite). By contrast, monoclinic weberite (γ ≈ 91.8°) provided an excellent fit, with no major misfits observed. This unit cell features distorted YO 8 dodecahedra, YO 7 monocapped octahedra, and NbO 6 octahedra as building blocks. Comparison between the topologies of the cationic and anionic substructures in monoclinic weberite and its parent orthorhombic C structure revealed displacements of the metal atoms along the [100] direction and a less compact spatial distribution of oxygen atoms along the a axis. In conclusion, the monoclinic weberite model presented herein may serve as a starting point to revisit structural modeling of fluorite-based materials with challenging local structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

In-situ observation of nano-oxide and defect evolution in 14YWT alloys

Nanostructured ferritic alloys (NFAs) are considered as candidates for structural components in advanced nuclear reactors due to their excellent radiation resistance as a result of a high density of nano-oxides (NOs) in the microstructure. Therefore, gaining an understanding on the stability of NOs under irradiation is crucial. In this study, we have investigated the evolution of defects and NOs in 14YWT NFAs under in-situ Kr ion irradiation at room temperature (RT) and 450°C up to 10 dpa. It has been found that irradiations at 450°C do not create any changes in the NOs, similar to the bulk irradiations. On the other hand, elemental mapping indicates that NOs dissolve mostly after 10 dpa irradiations at RT. Thus, while defects are both annihilated and pinned by NOs at low doses (before the dissolution of NOs), glissile loops start to escape to the foil surface at high doses (after the dissolution of NOs), justifying the significantly low fraction of (111) loops compared to the literature values. Furthermore, high resolution transmission electron microscopy analysis has shown that the NOs are mostly coherent Y 2 Ti 2 O 7 particles with pyrochlore crystal structure after both RT and 450°C irradiations, similar to those observed before irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mapping 3D grain and precipitate structure during in situ mechanical testing of open-cell metal foam using micro-computed tomography and high-energy X-ray diffraction microscopy

Open-cell metal foams are ultra-low-density cellular metals with complex hierarchical structures that span bulk, cell, ligament, and sub-ligament scales and give rise to desirable properties such as high strength-to-weight ratio and excellent energy absorption. Although literature suggests that intrinsic material structures at sub-ligament length scales (e.g., grains and precipitates) play an important role in mechanical behavior of open-cell metal foams, there are very few experimental measurements of such structures in three dimensions and for meaningful volumes of foam. This study seeks to map and track the three-dimensional (3D) grain and precipitate structures of an intact volume of open-cell aluminum foam by advancing microstructural characterization techniques that leverage X-ray micro-computed tomography (μCT) and far-field high-energy X-ray diffraction microscopy (FF-HEDM). A 6%-relative-density aluminum foam sample was mechanically tested in compression while μCT and FF-HEDM measurements were collected at interrupted loading states at beamline 1-ID of the Advanced Photon Source. Further, a new scanning strategy and reconstruction algorithm were established to enable characterization of a foam volume with diameter approximately four times wider than the nominal width of the X-ray beam. The result is a set of maps that detail both the 3D grain and precipitate structures throughout the foam volume at successive strain steps. A novel grain tracking procedure was developed to track individual grains within the foam volume by accounting for the large rigid-body motions that individual ligaments can undergo during mechanical loading. The ability to track grains and precipitate structures in three dimensions throughout large bulk deformation of ultra-low-density polycrystalline materials enables new possibilities for validating numerical models and investigating local failure mechanisms. Furthermore, the methods and procedures developed in this study could be applied to other ultra-low-density structures, such as additively manufactured lattices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strengthening mechanisms, hardening/softening behavior, and microstructure evolution in an LPSO magnesium alloy at elevated temperatures

Here, rapid degradation of the mechanical properties of conventional Mg alloys with temperature precludes their wide application in industry. The LPSO (long period stacking ordered) Mg alloys, on the other hand, show considerable potential to achieve excellent high-temperature mechanical performance. In this study, a Mg-5.1Y-2.4Zn (wt.%) extrusion alloy with the microstructure comprising of α-Mg matrix and LPSO phase was prepared. It is shown that the yield strength of the alloy at 200 °C retained ~83% of the yield strength of 198 MPa at room temperature (RT). Importantly, the ductility also improved, owing to the increased non-basal slip activities at elevated temperatures. In contrast to RT and 200 °C, the alloy exhibited softening tensile behavior with an apparent loss of yield strength at 300 °C. In-situ lattice strain analysis revealed that load transfer from α-Mg to LPSO remains effective at temperatures up to 200 °C, governing the high yield strength of the alloy. The post-mortem analysis by means of electron microscopy confirmed that the LPSO phase is structurally stable at 200 °C. In particular, the high strain hardenability is rationalized by the sandwiched LPSO structures together with stacking faults serving as effective obstacles to the motion of non-basal dislocations. The load transfer effect disappears at the temperature of 300 °C, resulting in the fast deterioration of strength of the alloy. The cracking of the LPSO phase along with the recrystallizing of α-Mg grains were found to be the main causes for the softening behavior of the alloy at 300 °C.

36 MATERIALS SCIENCE↗