Results for “profilometry” — Page 8

NASA NTRS2018

In-Situ Diagnostic for Assessing Hall Thruster Wear

The design of a new diagnostic to measure the net erosion of Hall thruster surfaces is presented. This diagnostic consists of a pair of optical non-contact profilometer pens mounted to a set of motion stages, which can interrogate the surface features of multiple components of interest including the hollow cathode assembly, magnet front pole covers, and discharge channel. By comparing scans of these surfaces to reference features, estimates of the component erosion rates can be acquired throughout long-duration lifetime tests without venting and removing the thruster from the vacuum facility for external profilometry. This work presents a detailed overview of the diagnostic design including the precision positioning system. In addition, preliminary data are shown which verify diagnostic operation and establish a baseline that will be used to track the erosion of the Hall Effect Rocket with Magnetic Shielding (HERMeS) Technology Demonstration Unit 3 (TDU-3) during an ongoing long-duration wear test.

Ahern, Drew M.↗

NASA NTRS2016

Synthesis, Characterization and Evaluation of Urethane Co-Oligomers Containing Pendant Fluoroalkyl Ether Groups

Coatings with the ability to minimize adhesion of insect residue and other debris are of great interest for future aircraft. These aircraft will exhibit increased fuel efficiency by maintaining natural laminar flow over greater wing chord distances. Successful coatings will mitigate the adhesion of debris on laminar flow surfaces that could cause a premature transition to turbulent flow. The use of surface modifying agents (SMA) that thermodynamically orient towards the air side of a coating can provide specific surface chemistry that may lead to a reduction of contaminate adhesion. Aluminum surfaces coated with urethane co-oligomers containing various amounts of pendant fluoroalkyl ether groups were prepared, characterized and tested for their abhesive properties. The coated surfaces were subjected to controlled impacts with wingless fruit flies (drosophila melanogaster) using both a benchtop wind tunnel and a larger-scale wind tunnel test facility. Insect impacts were recorded and analyzed using high-speed digital photography and the remaining residues characterized using optical surface profilometry and compared to that of an aluminum control. It was determined that using fluorinated oligomers to chemically modify coating surfaces altered the adhesion properties relative to the adhesion of insect residues to the surface.

Jereme R Doss↗

NASA NTRS2019

Uncertainty in Electric Propulsion Erosion Measurements

Uncertainty in erosion rates as measured by different methods is discussed and quantified. The work focuses on case studies from components on the Hall Effect Rocket with Magnetic Shielding (HERMeS) Hall thruster, but the methods can be extended for many electric propulsion applications. The primary method used for evaluating erosion is non-contact profilometry of masked and exposed components. Accurate quantification of the erosion rates of components is critical to determining lifetime and is therefore critical to mission planning purposes.

Mackey, J.↗

NASA NTRS2019

Uncertainty in Electric Propulsion Erosion Measurements

Uncertainty in erosion rates as measured by different methods is discussed and quantified. The work focuses on case studies from components on the Hall Effect Rocket with Magnetic Shielding (HERMeS) Hall thruster, but the methods can be extended for many electric propulsion applications. The primary method used for evaluating erosion is non-contact profilometry of masked and exposed components. Accurate quantification of the erosion rates of components is critical to determining lifetime and is therefore critical to mission planning purposes.

Mackey, Jonathan A.↗

NASA NTRS2020

Uncertainty in Electric Propulsion Erosion Measurements

Uncertainty in erosion rates as measured by different methods is discussed and quantified. The work focuses on case studies from components on the Hall Effect Rocket with Magnetic Shielding (HERMeS) Hall thruster, but the methods can be extended for many electric propulsion applications. The primary method used for evaluating erosion is non-contact profilometry of masked and exposed components. Accurate quantification of the erosion rates of components is critical to determining lifetime and is therefore critical to mission planning purposes.

Jonathan A Mackey↗

NASA NTRS2019

Machine Learning Based AFP Inspection: A Tool for Characterization and Integration

Automated Fiber Placement (AFP) has become a standard manufacturing technique in the creation of large scale composite structures due to its high production rates. However, the associated rapid layup that accompanies AFP manufacturing has a tendency to induce defects. We forward an inspection system that utilizes machine learning (ML) algorithms to locate and characterize defects from profilometry scans coupled with a data storage system and a user interface (UI) that allows for informed manufacturing. A Keyence LJ-7080 blue light profilometer is used for fast 2D height profiling. After scans are collected, they are process by ML algorithms, displayed to an operator through the UI, and stored in a database. The overall goal of the inspection system is to add an additional tool for AFP manufacturing. Traditional AFP inspection is done manually adding to manufacturing time and being subject to inspector errors or fatigue. For large parts, the inspection process can be cumbersome. The proposed inspection system has the capability of accelerating this process while still keeping a human inspector integrated and in control. This allows for the rapid capability of the automated inspection software and the robustness of a human checking for defects that the system either missed or misclassified.

Sacco, Christopher↗

NASA NTRS2001

April 1998 Asian dust event: A southern California perspective

In late April 1998 an extreme Asian dust episode reached the U.S. western seaboard. This event was observed by several in situ and remote sensing atmospheric measurement stations. Dramatic reductions in boundary layer visibility were recorded and the resultant peak backscatter coefficients exceeded prevailing upper tropospheric background conditions by at least 2 orders of magnitude. An analysis of this event is given using lidar vertical backscatter profilometry, concurrent Sun photometer opacity data, and transport modeling.

aerosol↗

NASA NTRSDate not supplied

Understanding the Feasibility of MAB Phase Structures for Lunar Applications

During the ten-week internship, my work focused on synthesis, characterization, and tailoring the flowability of the MAB phase powders for improving the surface finish and decreasing porosity of 3D-printed MAB phase structures. My mentor for the project was Dr. Samuel Hocker from NASA Langley and my faculty advisor was Dr. Surojit Gupta from the University of North Dakota. I also collaborated with Daniel Trieff from the University of North Dakota in developing characterization paradigm of 3D printed samples. The microencapsulation was performed via novel solvent casting-based microencapsulation process pioneered in UND, wherein a polymer (PLA, PHA) was dissolved into dichloromethane and precipitated onto the surface of the MoAlB particles. Two 100mL samples of microencapsulated powder was outsourced to Particle Technology Labs for flowability testing along with a 100mL control sample to determine if microencapsulation is a valid method for improving the flowability. The microencapsulated powders were characterized using SEM, Differential Scanning Calorimetry, and optical microscopy. The SEM images showed no change between the pure and microencapsulated powders. The optical microscopy analysis indicated a reduction in reflectivity for the PLA microencapsulated powders as well as hydrophobic properties. Both results suggest that microencapsulation was successful as PLA is a hydrophobic polymer and the change in reflectivity could be a result of the light being dispersed through the polymer coating. A reflectivity analysis will be done to bring more perspective to these observations. If powder flowability is improved, then the project will move forward with testing the printability of the microencapsulated powders and characterizing the structures using the designed characterization protocol. We are waiting for the DSC results. The characterization protocol for the 3D-printed MAB structures included a visual inspection of the plates to rule out any samples that had spalled or delaminated, optical microscopy to document surface features, porosity, and decomposition, and cleaning of the plates using an ultrasonic bath in preparation for SEM, EDS, and profilometry analyses.

MAB Phase↗

NASA NTRSDate not supplied

High-Propellant Throughput Sub-kW Electric Propulsion System for Deep Space Science and Exploration

The National Aeronautics and Space Administration (NASA) is maturing high-propellant throughput sub-kilowatt electric propulsion technologies to enable small spacecraft deep space science and exploration missions with high delta-v requirements. The pathfinder model (PM) propulsion system consists of the H71M-PM Hall-effect thruster, a breadboard 1-kW power processing unit (PPU), and a propellant flow control system. The propulsion system requirements balance the needs of various high delta-v NASA and commercial industry mission concepts to achieve a design that both enables a variety of NASA small spacecraft deep space missions, while remaining viable for select commercial applications. The H71M-PM thruster has completed performance characterization and three 500-h short duration wear tests (SDWT). The propulsion system provides stable thrust generation over a wide range of operating conditions from 200 W to 1 kW, and 200 V to 400 V. The thruster has demonstrated a thrust as high as 68 mN at 300 V and 1 kW. The thruster has similarly demonstrated a specific impulse of 1850 s at 400 V and 1 kW. Key surfaces were machined between each SDWT to simulate accelerated discharge channel and pole cover erosion. Profilometry scans across masked pole cover surfaces were conducted to determine erosion rates. SDWT results support that a target thruster lifetime of 14 kh with 50% margin is achievable. Component testing has demonstrated propellant azimuthal flow uniformity better than ± 2 percent of the nominal value, azimuthal magnetic field uniformity better than ± 0.5 percent of the nominal value, and cathode heater cycle testing to greater than 30,000 cycles. Propulsion system integrated system testing is planned to use the H71M-PM and a breadboard 1-kW PPU. Pathfinder model test results are now supporting the design of the H71M-EM engineering model thruster. A second-generation breadboard PPU has been fabricated and is currently under test. NASA has made these technologies available to U.S. industry through a no cost, nonexclusive license agreement.

Hall↗

NASA NTRS2023

The Effect of Oxidation in Environmental Barrier Coatings Subject to Foreign Object Damage

Oxidation and foreign object damage (FOD) are two key failure modes for environmental barrier coatings (EBCs). For EBCs with a silicon (Si) bond coat, a thermally grown oxide (TGO) layer forms at the EBC –bond coat interface. The TGO layer is considered the weak interface, and directly influences the life of the EBC. Moreover, FOD has been shown to cause significant subsurface damage resulting in delamination or spallation of the EBC which can occur at the EBC -bond coat interface or the bond coat -substrate interface. The purpose of this work is to investigate the synergistic effects of oxidation and FOD in a ytterbium disilicate (𝑌𝑏2𝑆𝑖2𝑂7) EBC. FOD testing is conducted on as-deposited and steam oxidized samples at room temperature using a 1.59-mm hardened steel ball projectile. The resulting damage is characterized by optical profilometry and scanning electron microscopy (SEM). Additionally, a quasi-static, mechanical assessment of the EBC bond strength in the presence of a growing TGO is presented.

environmental barrier coatings (EBCs)↗

NASA NTRS2023

Using the Potassium-Argon Laser Experiment (KArLE) to Date Ancient, Low-K Chondritic Meteorites

Several laboratories have been investigating the feasibility of in situ K-Ar dating for use in future landing planetary missions. One drawback of these laboratory demonstrations is the insufficient analogy of the analyzed analog samples with expected future targets. We present the results obtained using the K-Ar laser experiment (KArLE) on two old and K-poor chondritic samples, Pułtusk and Hvittis, as better lunar analogs. The KArLE instrument uses laser ablation to vaporize rock samples and quantifies K content by laser-induced breakdown spectroscopy (LIBS), Ar by quadrupole mass spectrometry (QMS), and ablated mass by laser profilometry. We performed 64 laser ablations on the chondrites to measure spots with a range of K 2 O and Ar content and used the data to construct isochrons to determine the chondrite formation age. The KArLE isochron ages on Pułtusk and Hvittis are 5059 ± 892 Ma and 4721 ± 793 Ma, respectively, which is within the uncertainty of published reference ages, and interpreted as the age of their formation. The uncertainty (2σ) on the KArLE ages obtained in this study is better than 20% (18% for Pułtusk and 17% for Hvittis). The precision, which compares our obtained ages to the reference ages, is also better than 20% (11% for Pułtusk and 4% for Hvittis). These results are encouraging for understanding the limits of this technique to measure ancient planetary samples and for guiding future improvements to the instrument.

Fanny Cattani↗

NASA NTRSDate not supplied

Additive Manufacturing and Working Fluid Characterization of Ceramic Heat Pipes

In this work, additively manufactured (AM) aluminum nitride (AlN) ceramic heat pipes were developed to improve spacecraft heat rejection capabilities beyond the current state-of-the-art metal systems. A low sintering temperature aluminum nitride slurry is developed for digital light processing printing (DLP) and the optimal debinding curves are examined. Printed AlN parts are characterized via SEM and optical profilometry. AlN 3D-printed parts are also tested for compatibility with aluminum bromide, aluminum chloride, and iodine, among other proposed working fluids at 350-600 K in an inert atmosphere, with reactivity measured via SEM and Fourier transform infrared spectroscopy (FTIR).

Thermal Management↗

NASA NTRSDate not supplied

Additive Manufacturing and Working Fluid Characterization of Ceramic Heat Pipes

In this work, additively manufactured aluminum nitride (AlN) ceramic heat pipes are developed to improve spacecraft heat rejection capabilities beyond the current state-of-the-art metal systems. Printed AlN parts are characterized via SEM, EDS, X-ray diffraction, optical profilometry, thermal conductivity, and emissivity testing. AlN 3D-printed parts are also tested for compatibility with aluminum bromide, aluminum chloride, and iodine, among other proposed working fluids at 500-600 K in vacuum.

Thermal management↗

NASA NTRSDate not supplied

Foreign Object Damage in a Yb2Si2O7 Environmental Barrier Coating

Foreign object damage (FOD) is one of the key damage/failure modes in environmental barrier coatings (EBCs) developed for gas turbine engines. A limiting factor of EBC development is the growth of a SiO2 thermally grown oxide (TGO) layer which exacerbates spallation. While there has been extensive research on FOD in metals, ceramics, and ceramic matrix composites (CMCs), there is a limited understanding of the effects of FOD in EBC systems. Previous work studied the effects of TGO growth on FOD in NASA’s Generation II Ytterbium Disilicate EBC. Recently, it has been shown that the addition of oxide modifiers to the Ytterbium Disilicate EBC resulted in significant reduction in TGO growth. The present work will compare FOD in a modified Ytterbium Disilicate EBC to that of the baseline Ytterbium Disilicate EBC. FOD testing was conducted on both as-processed and steam cycled samples at room temperature using a 1.59mm steel ball projectile with particle velocities ranging from 50–300 m/s at a normal incidence angle. The impact damage was characterized by optical profilometry and scanning electron microscopy (SEM) of the cross-sections.

Leland Hoffman↗

NASA NTRSDate not supplied

A Dynamic Testing Approach for Particulate Erosion–Corrosion for Gas Turbine Coatings

Particle interactions in gas turbine engines can be multicomponent, complex phenomena leading to the degradation of thermal (TBCs) and environmental barrier coatings (EBCs) meant to protect engine components. Ingestion of particles into the engine can lead to recession of coatings due to particle erosion. Similarly, these same particles can become molten, adhere to coatings and result in thermochemical corrosion of coating materials. Particle erosion testing is often carried out where the particles are injected into a gas stream, accelerated within a nozzle, and impinge on sample. Conversely, most molten particle corrosion testing is often done in static laboratory furnaces, which does not capture the dynamic nature of deposition in application. Nevertheless, these damage mechanisms are often tested separately and no single standard exists to test both erosive and corrosive particle interactions with coating materials under relevant operating conditions for gas turbine engines. Understanding the synergies of particle interactions in engines is crucial in determining operating lifetimes of potential coating materials. Such considerations emphasize the need for realistic approaches in standardizing particle interaction testing in combustion environments. The current study outlines initial efforts at NASA Glenn’s Erosion Burner Rig Facility in improving dynamic erosion/corrosion testing methods by assessing the durability of state-of-the-art (SOA) TBC material 7 wt.% yttria stabilized zirconia (7YSZ) as a function of particle deposition rate, burner temperature, and particle size. Calibration data to determine particle deposition rate will be presented, and mass and optical profilometry measurements were utilized to estimate mass/volume loss versus deposition per increment of particulate used over time. Electron microscopy analyses were then carried out to assess coating damage after testing.

TBC↗

NASA NTRSDate not supplied

A Dynamic Testing Approach for Particulate Erosion–Corrosion for Gas Turbine Coatings

Particle interactions in gas turbine engines can be multicomponent, complex phenomena leading to the degradation of thermal (TBCs) and environmental barrier coatings (EBCs) meant to protect engine components. Ingestion of particles into the engine can lead to recession of coatings due to particle erosion. Similarly, these same particles can become molten, adhere to coatings and result in thermochemical corrosion of coating materials. Particle erosion testing is often carried out where the particles are injected into a gas stream, accelerated within a nozzle, and impinge on sample. Conversely, most molten particle corrosion testing is often done in static laboratory furnaces, which does not capture the dynamic nature of deposition in application. Nevertheless, these damage mechanisms are often tested separately and no single standard exists to test both erosive and corrosive particle interactions with coating materials under relevant operating conditions for gas turbine engines. Understanding the synergies of particle interactions in engines is crucial in determining operating lifetimes of potential coating materials. Such considerations emphasize the need for realistic approaches in standardizing particle interaction testing in combustion environments. The current study outlines initial efforts at NASA Glenn’s Erosion Burner Rig Facility in improving dynamic erosion/corrosion testing methods by assessing the durability of state-of-the-art (SOA) TBC material 7 wt.% yttria stabilized zirconia (7YSZ) as a function of particle deposition rate, burner temperature, and particle size. Calibration data to determine particle deposition rate will be presented, and mass and optical profilometry measurements were utilized to estimate mass/volume loss versus deposition per increment of particulate used over time. Electron microscopy analyses were then carried out to assess coating damage after testing.

TBC↗

NASA NTRSDate not supplied

A Dynamic Testing Approach for Particulate Erosion–Corrosion for Gas Turbine Coatings

Particle interactions in gas turbine engines can be multicomponent, complex phenomena leading to the degradation of thermal (TBCs) and environmental barrier coatings (EBCs) meant to protect engine components. Ingestion of particles into the engine can lead to recession of coatings due to particle erosion. Similarly, these same particles can become molten, adhere to coatings and result in thermochemical corrosion of coating materials. Particle erosion testing is often carried out where the particles are injected into a gas stream, accelerated within a nozzle, and impinge on sample. Conversely, most molten particle corrosion testing is often done in static laboratory furnaces, which does not capture the dynamic nature of deposition in application. Nevertheless, these damage mechanisms are often tested separately and no single standard exists to test both erosive and corrosive particle interactions with coating materials under relevant operating conditions for gas turbine engines. Understanding the synergies of particle interactions in engines is crucial in determining operating lifetimes of potential coating materials. Such considerations emphasize the need for realistic approaches in standardizing particle interaction testing in combustion environments. The current study outlines initial efforts at NASA Glenn’s Erosion Burner Rig Facility in improving dynamic erosion/corrosion testing methods by assessing the durability of state-of-the-art (SOA) TBC material 7 wt.% yttria stabilized zirconia (7YSZ) as a function of particle deposition rate, burner temperature, and particle size. Calibration data to determine particle deposition rate will be presented, and mass and optical profilometry measurements were utilized to estimate mass/volume loss versus deposition per increment of particulate used over time. Electron microscopy analyses were then carried out to assess coating damage after testing.

burner rig↗

NASA NTRS2026

Radiation-Conditioned Ti–hBN Coatings for Space Mechanisms: Bridging Tribology and Irradiation Effects from Laboratory to Low-Earth Orbit

The longevity of tribological components in extraterrestrial environments is challenged by abrasive regolith, extreme temperatures, and ionizing radiation. This study evaluates the performance of vacuum plasma sprayed (VPS) Ti-2vol.% hexagonal boron nitride (hBN) coatings applied to joint mechanisms such as rod and slot, ball and socket, and hinge assemblies, fabricated from Al6061 and Ti6Al4V for planetary structures. Coated and uncoated samples were tested under vacuum with lunar regolith simulant (JSC-1A), followed by environmental exposures including electron radiation and thermal cycling. Results show that coated samples consistently outperformed uncoated counterparts across all configurations. Wear depth in coated components was reduced by over 80%, as confirmed by 3D profilometry and surface imaging. SEM analysis revealed severe abrasion and localized plastic deformation in uncoated surfaces, while coated samples retained structural integrity due to synergy of hard protective phases formed during deposition and retained hBN providing solid lubrication in the sliding surface. Coated and exposed samples exhibited smoother actuation profiles and reduced friction, indicating a beneficial "conditioning" effect from environmental exposure. The coatings-maintained performance even on complex geometries with minimal delamination. These findings demonstrate the potential of VPS Ti-hBN coatings to extend the operational life of lunar mechanisms, bridging laboratory-scale tribology with flight-relevant mechanical applications.

tribology↗