Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flight data analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Thermal Property Parameter Estimation of TPS Materials

Accurate knowledge of the thermophysical properties of TPS (thermal protection system) materials is necessary for pre-flight design and post-flight data analysis. Thermal properties, such as thermal conductivity and the volumetric specific heat, can be estimated from transient temperature measurements using non-linear parameter estimation methods. Property values are derived by minimizing a functional of the differences between measured and calculated temperatures. High temperature thermal response testing of TPS materials is usually done in arc-jet or radiant heating facilities which provide a quasi one-dimensional heating environment. Last year, under the NASA-ASEE-Stanford Fellowship Program, my work focused on developing a radiant heating apparatus. This year, I have worked on increasing the fidelity of the experimental measurements, optimizing the experimental procedures and interpreting the data.

Maddren, Jesse↗
NASA NTRS2002

Flexible-Wing-Based Micro Air Vehicles

This paper documents the development and evaluation of an original flexible-wing-based Micro Air Vehicle (MAV) technology that reduces adverse effects of gusty wind conditions and unsteady aerodynamics, exhibits desirable flight stability, and enhances structural durability. The flexible wing concept has been demonstrated on aircraft with wingspans ranging from 18 inches to 5 inches. Salient features of the flexible-wing-based MAV, including the vehicle concept, flexible wing design, novel fabrication methods, aerodynamic assessment, and flight data analysis are presented.

Ifju, Peter G.↗
NASA NTRS2003

Monte Carlo Methodology Serves Up a Software Success

Widely used for the modeling of gas flows through the computation of the motion and collisions of representative molecules, the Direct Simulation Monte Carlo method has become the gold standard for producing research and engineering predictions in the field of rarefied gas dynamics. Direct Simulation Monte Carlo was first introduced in the early 1960s by Dr. Graeme Bird, a professor at the University of Sydney, Australia. It has since proved to be a valuable tool to the aerospace and defense industries in providing design and operational support data, as well as flight data analysis. In 2002, NASA brought to the forefront a software product that maintains the same basic physics formulation of Dr. Bird's method, but provides effective modeling of complex, three-dimensional, real vehicle simulations and parallel processing capabilities to handle additional computational requirements, especially in areas where computational fluid dynamics (CFD) is not applicable. NASA's Direct Simulation Monte Carlo Analysis Code (DAC) software package is now considered the Agency s premier high-fidelity simulation tool for predicting vehicle aerodynamics and aerothermodynamic environments in rarified, or low-density, gas flows.

Source record↗
NASA NTRS2004

APMS 3.0 Flight Analyst Guide: Aviation Performance Measuring System

The Aviation Performance Measuring System (APMS) is a method-embodied in software-that uses mathematical algorithms and related procedures to analyze digital flight data extracted from aircraft flight data recorders. APMS consists of an integrated set of tools used to perform two primary functions: a) Flight Data Importation b) Flight Data Analysis.

Jay, Griff↗
NASA NTRSDate not supplied

OverFlight: Graphical Flight Operations Planning

OverFlight is an in-development graphical user interface (GUI) that implements a state-of-the-art rotorcraft maneuvering noise model using a source noise hemisphere approach coupled with the Aircraft NOise Prediction Program 2 (ANOPP2). This GUI stems from a demand for easy-to-use mission planning and community impact acoustic tools that can model the maneuvering flight of a rotary-wing vehicle. This paper covers the models used for the development of OverFlight and model validation efforts. Data from a joint NASA/Army flight test of an MD530F aircraft are used both for source noise hemispheres as well as maneuvering flight data. Analysis of the predicted maneuvering noise shows better agreement that traditional methods currently employed, while also demonstrating maneuvers where the underlying assumptions fail to hold.

rotorcraft↗
NASA NTRS2016

UAS Integration in the NAS Project: Flight Test 3 Data Analysis of JADEM-Autoresolver Detect and Avoid System

The Unmanned Aircraft Systems Integration in the National Airspace System project, or UAS Integration in the NAS, aims to reduce technical barriers related to safety and operational challenges associated with enabling routine UAS access to the NAS. The UAS Integration in the NAS Project conducted a flight test activity, referred to as Flight Test 3 (FT3), involving several Detect-and-Avoid (DAA) research prototype systems between June 15, 2015 and August 12, 2015 at the Armstrong Flight Research Center (AFRC). This report documents the flight testing and analysis results for the NASA Ames-developed JADEM-Autoresolver DAA system, referred to as 'Autoresolver' herein. Four flight test days (June 17, 18, 22, and July 22) were dedicated to Autoresolver testing. The objectives of this test were as follows: 1. Validate CPA prediction accuracy and detect-and-avoid (DAA, formerly known as self-separation) alerting logic in realistic flight conditions. 2. Validate DAA trajectory model including maneuvers. 3. Evaluate TCAS/DAA interoperability. 4. Inform final Minimum Operating Performance Standards (MOPS). Flight test scenarios were designed to collect data to directly address the objectives 1-3. Objective 4, inform final MOPS, was a general objective applicable to the UAS in the NAS project as a whole, of which flight test is a subset. This report presents analysis results completed in support of the UAS in the NAS project FT3 data review conducted on October 20, 2015. Due to time constraints and, to a lesser extent, TCAS data collection issues, objective 3 was not evaluated in this analysis.

flight test↗
NASA NTRS1994

Space flight risk data collection and analysis project: Risk and reliability database

The focus of the NASA 'Space Flight Risk Data Collection and Analysis' project was to acquire and evaluate space flight data with the express purpose of establishing a database containing measurements of specific risk assessment - reliability - availability - maintainability - supportability (RRAMS) parameters. The developed comprehensive RRAMS database will support the performance of future NASA and aerospace industry risk and reliability studies. One of the primary goals has been to acquire unprocessed information relating to the reliability and availability of launch vehicles and the subsystems and components thereof from the 45th Space Wing (formerly Eastern Space and Missile Command -ESMC) at Patrick Air Force Base. After evaluating and analyzing this information, it was encoded in terms of parameters pertinent to ascertaining reliability and availability statistics, and then assembled into an appropriate database structure.

Source record↗
NASA NTRS1981

Application of a flight test and data analysis technique to flutter of a drone aircraft

Modal identification results presented were obtained from recent flight flutter tests of a drone vehicle with a research wing (DAST ARW-1 for Drones for Aerodynamic and Structural Testing, Aeroelastic Research Wing-1). This vehicle is equipped with an active flutter suppression system (FSS). Frequency and damping of several modes are determined by a time domain modal analysis of the impulse response function obtained by Fourier transformations of data from fast swept sine wave excitation by the FSS control surface on the wing. Flutter points are determined for two different altitudes with the FSS off. Data are given for near the flutter boundary with the FSS on.

Bennett, R. M.↗
NASA NTRS1981

Application of a flight test and data analysis technique to flutter of a drone aircraft

Modal identification results are presented that were obtained from recent flight flutter tests of a drone vehicle with a research wing equipped with an active flutter suppression system (FSS). Frequency and damping of several modes are determined by a time domain modal analysis of the impulse response function obtained by Fourier transformations of data from fast swept sine wave excitation by the FSS control surfaces on the wing. Flutter points are determined for two different altitudes with the FSS off. Data are given for near the flutter boundary with the FSS on.

Bennett, R. M.↗
NASA NTRS1993

An examination of the aerodynamic moment on rotor blade tips using flight test data and analysis

The analysis CAMRAD/JA is used to model two aircraft, a Puma with a swept-tip blade and a UH-60A Black Hawk. The accuracy of the analysis in predicting the torsion loads is assessed by comparing the predicted loads with measurements from flight tests. The influence of assumptions in the analytical model is examined by varying model parameters and comparing the predicted results to baseline values for the torsion loads. Flight test data from a research Puma are used to identify the source of torsion loads. These data indicate that the aerodynamic section moment in the region of the blade tip dominates torsion loading in high-speed flight. Both the aerodynamic section moment at the blade tip and the pitch-link loads are characterized by large positive (nose-up) moments in the first quadrant with rapid reversal of load so that the moment is negative in the second quadrant. Both the character and magnitude of this loading are missed by the CAMRAD/JA analysis.

Maier, Thomas H.↗
NASA NTRS1986

Real-time open-loop frequency response analysis of flight test data

A technique has been developed to compare the open-loop frequency response of a flight test aircraft real time with linear analysis predictions. The result is direct feedback to the flight control systems engineer on the validity of predictions and adds confidence for proceeding with envelope expansion. Further, gain and phase margins can be tracked for trends in a manner similar to the techniques used by structural dynamics engineers in tracking structural modal damping.

Bosworth, J. T.↗
NASA NTRS1976

Teledyne Continental Motors emissions data and analysis and flight test results

Five different engine models were tested covering combinations of all engine categories in current production in the range from 100 to 435 brake horsepower. Engines were divided into five major types: carbureted, fuel injected, direct drive, geared, and turbocharged. Emissions data were categorized by three separate fuel system schedules: baseline, case 1, and case 2. Baseline was defined as the average fuel flow rate established by the fuel system's production tolerance band when operated with the mixture control at the full-rich position. Case 1 was defined as the minimum allowable fuel flow rate established by the engine certification. Case 2 was defined as the fuel rate corresponding to the leanest fuel-air ratio obtainable before a safety limit occurred with the engine operating on a propeller test stand. Safety limits that developed during testing were cylinder-head overheating or inadequate acceleration from a given mode of operation.

Rezy, B. J.↗
NASA NTRS1984

Comparison of viscous-shock-layer heating analysis with Shuttle flight data in slip flow regime

Comparison of STS-2 Shuttle flight heating data along the windward centerline has been made with two-dimensional nonequilibrium viscous shock-layer solutions obtained with shock and wall-slip conditions at an altitude range of 90 to 110 km. The shock slip condition used is the modified Rankine-Hugoniot relations of Cheng as used by Davis, and the wall-slip conditions are based on the first order consideration derived from kinetic theory as given by Scott and Hendricks. The results indicate that the calculated heating distributions with slip boundary conditions agree better with the flight data than those without slip conditions. The agreement improves when the accommodation coefficient or freestream density is decreased to one-half, suggesting the possibility of less than full accommodation for the tile surface and (or) an overestimate of freestream density using the Jacchia-Roberts model. Heating reduction due to the slip effect becomes very pronounced as the flow becomes more rarefied, and the effect is more significant for the stagnation region than the aft region of the vehicle.

Shinn, J. L.↗
NASA NTRS1989

Aerodynamic flight evaluation analysis and data base update

Research was conducted to determine the feasibility of replacing the Solid Rocket Boosters on the existing Space Shuttle Launch Vehicle (SSLV) with Liquid Rocket Boosters (LRB). As a part of the LRB selection process, a series of wind tunnel tests were conducted along with aero studies to determine the effects of different LRB configurations on the SSLV. Final results were tabulated into increments and added to the existing SSLV data base. The research conducted in this study was taken from a series of wind tunnel tests conducted at Marshall's 14-inch Trisonic Wind Tunnel. The effects on the axial force (CAF), normal force (CNF), pitching moment (CMF), side force (CY), wing shear force (CSR), wing torque moment (CTR), and wing bending moment (CBR) coefficients were investigated for a number of candidate LRB configurations. The aero effects due to LRB protuberances, ET/LRB separation distance, and aft skirts were also gathered from the tests. Analysis was also conducted to investigate the base pressure and plume effects due to the new booster geometries. The test results found in Phases 1 and 2 of wind tunnel testing are discussed and compared. Preliminary LRB lateral/directional data results and trends are given. The protuberance and gap/skirt effects are discussed. The base pressure/plume effects study is discussed and results are given.

Boyle, W. W.↗
NASA NTRS1990

Correlation of boundary layer stability analysis with flight transition data

Recently, NASA completed a boundary-layer transition flight test on an F-14 aircraft which has variable-sweep capability. Transition data were acquired for a wide variety of sweep angles, pressure distributions, Mach numbers, and Reynolds numbers. In this paper, the F-14 flight test is briefly described and N-factor correlations with measured transition locations are presented for one of two gloves flown on the F-14 wing in the flight program; a thin foam and fiberglass glove which provided a smooth sailplane finish on the basic F-14, modified NACA 6-series airfoil. For these correlations, an improved linear boundary-layer stability theory was utilized that accounts for compressibility and surface and streamline curvature effects for the flow past swept wings.

Collier, F. S., Jr.↗
NASA NTRS2003

Turbulence Lidar Development Status

This viewgraph provides an overview of efforts conducted by Coherent Technologies, Inc. in conjunction with NASA Langley Research Center to develop a robust turbulence detection capability that spans full range of turbulence environments. Topics covered include: general principles of infrared doppler radar (lidar) turbulence measurement, performance simulation, complete detection capability provided by dual wavelength radar, algorithm development, technology development needs and turbulence detection problems. Versions of this turbulence lidar system were flight tested. Data analysis from these flight tests are presented. Future flight tests aboard DC-8 and B-757 are planned as well as continued algorithm development and performance simulation activities.

Clark, Ivan↗