Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Route optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Demonstration of MgCr 2– x Mn x O 4 Spinel Oxide Cathodes in High-Voltage Mg Batteries

Solid-solution oxide spinels with high redox voltages and facile Mg 2+ mobility have been identified as promising candidates for practical, high-voltage cathodes in Mg batteries. In this work, we discuss the development of MgCr 2-x Mn x O 4 [x = 0.5, 1, 1.2] solid-solution spinel oxides as a cathode material and their electrochemical performance paired with an Mg anode in a full cell. This work presents the first demonstration of full cells with these materials. Mg-Cr-Mn spinel oxides with varying Cr and Mn contents were synthesized using alternative synthetic routes for optimal electrochemical performance. High-resolution synchrotron powder X-ray diffraction (PXRD), solid-state nuclear magnetic resonance (NMR) spectroscopy, and electron microscopy showed that these different synthetic routes resulted in changes in structures and particle morphologies, which in turn affect the electrochemical performance. Particularly, the urea coprecipitation synthetic route resulted in high-surface-area particles that enabled lower overpotentials and increased discharge capacity. The high surface area also resulted in expedited structural degradation caused by the irreversible migration of Mg 2+ into normally vacant 16c sites in the spinel lattice. This structural degradation was lessened by using a hydrosauna-urea synthesis method, which decreased the Mg/Mn inversion ratio while retaining high-surface-area particles with good cycling performance. Furthermore, our findings highlight the necessity for high surface area or nanostructured spinel oxide cathodes with minimized Mg-Mn inversion to enable spinel oxide cathodes in Mg full cells.

Mg anode↗
NASA NTRS1999

Satellite ATM Networks: Architectures and Guidelines Developed

An important element of satellite-supported asynchronous transfer mode (ATM) networking will involve support for the routing and rerouting of active connections. Work published under the auspices of the Telecommunications Industry Association (http://www.tiaonline.org), describes basic architectures and routing protocol issues for satellite ATM (SATATM) networks. The architectures and issues identified will serve as a basis for further development of technical specifications for these SATATM networks. Three ATM network architectures for bent pipe satellites and three ATM network architectures for satellites with onboard ATM switches were developed. The architectures differ from one another in terms of required level of mobility, supported data rates, supported terrestrial interfaces, and onboard processing and switching requirements. The documentation addresses low-, middle-, and geosynchronous-Earth-orbit satellite configurations. The satellite environment may require real-time routing to support the mobility of end devices and nodes of the ATM network itself. This requires the network to be able to reroute active circuits in real time. In addition to supporting mobility, rerouting can also be used to (1) optimize network routing, (2) respond to changing quality-of-service requirements, and (3) provide a fault tolerance mechanism. Traffic management and control functions are necessary in ATM to ensure that the quality-of-service requirements associated with each connection are not violated and also to provide flow and congestion control functions. Functions related to traffic management were identified and described. Most of these traffic management functions will be supported by on-ground ATM switches, but in a hybrid terrestrial-satellite ATM network, some of the traffic management functions may have to be supported by the onboard satellite ATM switch. Future work is planned to examine the tradeoffs of placing traffic management functions onboard a satellite as opposed to implementing those functions at the Earth station components.

vonDeak, Thomas C.↗
DOE OSTI2023

Fort Erie On-Demand Transit Case Study

Rural and smaller-sized communities in North America face unique mobility challenges due to their low population density, lower public transit spending per capita compared to major cities, and a high reliance on private vehicles. In recent years, communities such as Fort Erie, Ontario have restructured or advanced their public transit systems using on-demand services. Fort Erie is a relatively sparsely populated region of 32,901 residents, spread across a land area of 166 square kilometers (64 square miles), for an average population density of 193 residents per square kilometer (500 per square mile). In October 2021, the town implemented a mobility-on-demand system integrated with smartphone software to replace its fixed-route community bus system, which consisted of four buses with three routes, each with a roughly one-hour, one way loop. The new service utilizes a fleet of six minivans, two of which are retrofitted with wheelchair-accessible ramps. The system may require that a passenger requesting a standard van walk up to 400 meters (a quarter mile) to their pickup location to optimize vehicle routing while providing origin-to-destination service. The on-demand system proved effective in providing service, eclipsing pre-pandemic ridership by 40%, decreasing greenhouse gas emissions per ride by 63%, and decreasing the cost per ride to the town by 29%. This report documents both the previous system and the new system in terms of routes, ridership, costs, fuel, and other notable system parameters. This work is part of an ongoing series of case studies on providing small communities with on-demand, right-sized vehicle service coupled with a smartphone application.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Fort Erie Case Study - Transition from Fixed-Route to On-Demand Transit

Rural and smaller-sized communities in North America face unique mobility challenges due to their low population density, lower public transit spending per capita compared to major cities, and a high reliance on private vehicles. In recent years, communities such as Fort Erie, Ontario, have restructured or advanced their public transit systems using on-demand services. Fort Erie is a relatively sparsely populated region of 32,901 residents, spread across a land area of 166 square kilometers (64 square miles), for an average population density of 193 residents per square kilometer (500 per square mile). In October 2021, the town implemented a mobility-on-demand system integrated with smartphone software to replace its fixed-route community bus system, which consisted of four buses with three routes, each with a roughly 1-hour, one-way loop. The new service utilizes a fleet of six minivans, two of which are retrofitted with wheelchair-accessible ramps. The system may require that a passenger requesting a standard van walk up to 400 meters (a quarter mile) to their pickup location to optimize vehicle routing while providing origin-to-destination service. The on-demand system proved effective in providing service, eclipsing pre-pandemic ridership by 40%, decreasing greenhouse gas emissions per ride by 63%, and decreasing the cost to the town per ride by 29%. This report documents both the previous system and the new system in terms of routes, ridership, costs, fuel, and other notable system parameters. This work is part of an ongoing series of case studies on providing small communities with on-demand, right-sized vehicle service coupled with a smartphone application.

ADVANCED PROPULSION SYSTEMS,ENERGY PLANNING, POLIC↗
DOE OSTI2023

NREL On-Demand Transit Research and Fort Erie Case Study

On-demand systems have increased in popularity in recent years, especially in rural and smaller-sized communities. This presentation provides a brief introduction to NREL's on-demand mobility research and an in-depth case study of the town of Fort Erie, Ontario. Fort Erie is a relatively sparsely populated region of 32,901 residents, spread across a land area of 166 square kilometers (64 square miles), for an average population density of 193 residents per square kilometer (500 per square mile). In October 2021, the town implemented a mobility-on-demand system integrated with smartphone software to replace its fixed-route community bus system, which consisted of four buses with three routes, each with a roughly 1-hour, one-way loop. The new service utilizes a fleet of six minivans, two of which are retrofitted with wheelchair-accessible ramps. The system may require that a passenger requesting a standard van walk up to 400 meters (a quarter mile) to their pickup location to optimize vehicle routing while providing origin-to-destination service. The on-demand system proved effective in providing service, eclipsing pre-pandemic ridership by 40%, decreasing greenhouse gas emissions per ride by 63%, and decreasing the cost to the town per ride by 29%. This presentation documents both the previous system and the new system in terms of routes, ridership, costs, fuel, and other notable system parameters. This work is part of an ongoing series of case studies on providing small communities with on-demand, right-sized vehicle service coupled with a smartphone application.

emerging technology↗
NASA NTRS2016

Design and Development of a Flight Route Modification, Logging, and Communication Network

There is an overwhelming desire to create and enhance communication mechanisms between entities that operate within the National Airspace System. Furthermore, airlines are always extremely interested in increasing the efficiency of their flights. An innovative system prototype was developed and tested that improves collaborative decision making without modifying existing infrastructure or operational procedures within the current Air Traffic Management System. This system enables collaboration between flight crew and airline dispatchers to share and assess optimized flight routes through an Internet connection. Using a sophisticated medium-fidelity flight simulation environment, a rapid-prototyping development, and a unified modeling language, the software was designed to ensure reliability and scalability for future growth and applications. Ensuring safety and security were primary design goals, therefore the software does not interact or interfere with major flight control or safety systems. The system prototype demonstrated an unprecedented use of in-flight Internet to facilitate effective communication with Airline Operations Centers, which may contribute to increased flight efficiency for airlines.

Merlino, Daniel K.↗
DOE OSTI2015

Synthesis, characterization and rate capability performance of the micro-porous MnO{sub 2} nanowires as cathode material in lithium batteries

Graphical abstract: Translating MnO{sub 2} nanowires as cathode materials in coin cell and studying their discharge behavior and cycling stability at different C-rates. - Highlights: • MnO{sub 2} nanowires have been synthesized via hydrothermal route. • The nanowires were employed as cathode materials in Li-batteries. • Discharge and cycling stability were studied at different C-rates. • Specific capacity and power density of 251 mAh g{sup −1} and 200 W kg{sup −1} were attained. - Abstract: A peculiar architecture of one-dimensional MnO{sub 2} nanowires was synthesized by an optimized hydrothermal route and has been lucratively exploited to fabricate highly efficient microporous electrode overlays for lithium batteries. These fabricated electrodes comprised of interconnected nanoscale units with wire-shaped profile which exhibits high aspect ratio in the order of 10{sup 2}. Their outstanding intercalation/de-intercalation prerogatives have also been studied to fabricate lithium coin cells which revealed a significant specific capacity and power density of 251 mAh g{sup −1} and 200 W kg{sup −1}, respectively. A detailed electrochemical study was performed to elucidate how surface morphology and redox reaction behaviors underlying these electrodes influence the cyclic behavior of the electrode. Rate capability tests at different C-rates were performed to evaluate the capacity and cycling performance of these coin cells.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Mechanical Characteristics of Additively Manufactured ODS 316L and 316H Alloys with and Without Post-build Processing

This research aims to explore an accelerated development path for oxide dispersion-strengthened (ODS) alloys by integrating additive manufacturing (AM) technologies with recent advances in ODS materials and traditional manufacturing methods. Novel AM and post-build processing routes have been developed for ODS austenitic alloys, specifically Fe-Cr-Ni alloys like 316L and 316H. Electron microscopy and mechanical characterizations were conducted to evaluate the effects of process variables on microstructure and properties, aiming for an economically feasible route property optimization. Traditionally, ODS alloy production involves multi-day high-energy mechanical milling of alloy powder with yttria (Y 2 O 3 ) followed by powder consolidation via extrusion or other methods and additional thermomechanical processing (TMP) for property control. Here, to address these challenges associated with this complex and costly approach, we propose exploring alternative, cost-effective processing routes focusing on AM and traditional TMP methods. The new ODS alloy processing routes have achieved up to a 400% increase in yield strength and a 60% increase in ultimate tensile strength compared to wrought stainless steels while still maintaining significant ductility and fracture toughness. This paper details the novel and economical AM-based processing routes for ODS austenitic alloys, combined with post-build TMPs, and discusses the mechanical and microstructural characteristics of the developed materials.

Byun, Thak Sang [Oak Ridge National Laboratory (OR↗
DOE OSTI2025

Bridging interfacial properties and cell performance: A multiscale model for proton-exchange-membrane fuel cells

Here, to elucidate the impact of local interfaces on mass-transport resistance and overall cell performance of low-loaded proton-exchange-membrane fuel cells (PEMFCs), we present a multiscale modeling framework incorporating a novel modified agglomerate model. The model considers three distinct Pt-electrolyte interfaces: Pt on the carbon surface covered by either ionomer or water film and Pt inside carbon nanopores. Detailed mass-transport voltage-loss breakdowns reveal that coupled agglomerate-interface-scale mass transport dominates the mass-transport loss. The ionomer poisons the exterior-Pt surface through suppressing O 2 adsorption and intrinsic ORR activity, leading to low current-density performance. Conversely, interior-Pt interface enhances the kinetic performance but limits high current-density performance due to its low interfacial permeability. The exterior-Pt/water interface demonstrates superior kinetic performance and mass transport, though its practical implementation requires ensuring proton transport. By coupling the multiscale CL properties with ink parameters, the model identifies an optimal I to C ratio of approximately 0.5, a moderate value where the ionomer content is sufficient to guarantee proton transport without fully covering the Pt surface and forming large agglomeration, thus allowing the utilization of the Pt-water interface and avoiding high mass-transport loss. Overall, the model helps unravel limiting phenomena across different operating regimes and provides routes for optimizing performance.

Cell diagnostic↗
DOE OSTI2026

Uncertainty quantification and reliability assessment for intermodal freight transportation

Intermodal freight optimization models support cost-effective, low-emission, and timely goods movement by coordinating trucks, rail, and barges. These models determine optimal flows, routing, and modal switches while respecting infrastructure and operational constraints. However, their real-world utility is often undermined by pervasive uncertainties-such as fluctuating transportation costs and emissions, variable terminal capacities, and uncertain freight demand-that distort key performance outcomes, including total system cost, carbon footprint, and transit time reliability. This study presents a structured framework for quantifying uncertainty in intermodal freight transportation (IFT) optimization. The framework evaluates how input uncertainty affects system performance and reliability, a critical need for ensuring that model-based decisions remain robust under real-world variability, especially amid volatile fuel prices, shifting demand, and growing disruptions. It integrates three complementary methods: (1) Sobol-based global sensitivity analysis to identify influential parameters affecting cost, emissions, and transit time, (2) Monte Carlo-based capacity perturbation analysis to assess robustness under probabilistic facility disruptions, and (3) Monte Carlo filtering with Bayesian inference to detect threshold-based performance vulnerabilities. The results highlight diesel truck unit cost as the dominant driver of variability. To improve system resilience, planners should prioritize uncertainty in fuel-related parameters when designing intermodal strategies.

Intermodal freight transportation↗
DOE OSTI2023

Phase-based design of CO 2 capture, transport, and storage infrastructure via SimCCS 3.0

The design of optimal infrastructure is essential for the deployment of commercial and large-scale carbon capture and storage (CCS) technology. During the design process, it is important to consider CO 2 capture and storage locations and CO 2 transportation pipelines to minimize the total project cost. SimCCS, first introduced in 2009, is an integrated open-source tool to optimize CCS infrastructure. The core CCS infrastructure design problem in SimCCS is structured as a mixed-integer linear programming problem by selecting the optimal pipeline routes, searching CO 2 source capture and storage locations, and determining the corresponding CO 2 amounts to meet desired capture targets. Multiple important and practical features have been developed to the latest version of SimCCS, SimCCS 3.0 . One of these features is phase-based modeling which enables users to dynamically design the CCS infrastructure. We demonstrate the phased-based modeling capability using two CCS infrastructure optimization case studies. The results from these case studies reveal that the phase-based modeling capability in SimCCS is particularly useful to optimize the dynamic deployment of CCS projects.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Optimized System for On-Route Fast Charging of Battery-Electric Shuttle Buses

Electrifying cars, buses, and trucks is an attractive means of reducing energy use and emissions because it involves more efficient drivetrain components and minimal restructuring of the transportation network. Transit buses, driving fixed routes, help minimize driver range anxiety by properly sizing energy storage systems. A major challenge to fully electrifying transit buses is providing the amount of energy they consume in a day of driving. To enable a full day of operation without charging, batteries need to be large, which could be expensive and heavy. This work utilizes real-world transit bus data used in a battery-electric drivetrain model to co-optimize charger locations, charger power levels, and vehicle battery sizes.

ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1977

Simulator evaluation of optimal thrust management/fuel conservation strategies for airbus aircraft on short haul routes

The feasibility of incorporating optimal concepts into a practical system was determined. Various earlier theoretical analyses were confirmed, and insight was gained into the sensitivity of fuel conservation strategies to nonlinear and second order aerodynamic and engine characteristics. In addition to the investigation of optimal trajectories the study ascertained combined fuel savings by utilizing various procedure-oriented improvements such as delayed flap/decelerating approaches and great circle navigation.

Bochem, J. H.↗
DOE OSTI2026

Benchmarking quantum trial wavefunctions for phaseless auxiliary-field quantum Monte Carlo

The phaseless auxiliary-field quantum Monte Carlo (ph-AFQMC) method is a stochastic imaginary-time projection technique for computing ground-state properties of strongly correlated quantum systems, with accuracy that depends critically on the choice of trial wavefunction. Here, we investigate ph-AFQMC with trial states prepared using parameterized quantum circuits. In this work, we present a comprehensive benchmarking study of quantum trial wavefunctions spanning unitary coupled-cluster, Hamiltonian-informed, Jastrow-inspired, and adaptively constructed ansatze. The benchmarking evaluates accuracy, expressibility, and scalability of these ansatze within the QC-AFQMC framework. We test these ansatze on linear hydrogen chains under bond stretching and find that several ansatz families produce chemically accurate ph-AFQMC energies across the dissociation curve. We have performed simulations using the CUDA-Q quantum development platform on the GPU partition of the Perlmutter supercomputer. When comparing ansatze at similar numbers of variational parameters, we find that different ansatz families yield comparable ph-AFQMC results despite exhibiting substantially different variational energies, optimization costs, and circuit depths. Our results indicate that the variational energy of an ansatz is not always a reliable indicator of its quality for ph-AFQMC and reveal instances of over-parameterization. In the strongly correlated regime, trial wavefunctions obtained from adaptive ansatze, exemplified here by ADAPT-VQE with the UCCSD operator pool, can outperform their fixed-ansatz counterparts (UCCSD) in terms of projected energies while using substantially more compact circuits, providing a flexible route to optimize quantum resources within the ph-AFQMC framework.

Rofougaran, Rod [LBNL, Berkeley; Columbia U.; PNL,↗
DOE OSTI2025

Tunable high Néel temperature and large anomalous Hall response in antiferromagnetic Weyl semimetal Mn 3 Sn 1− x Ga x thin films

Antiferromagnetic Weyl semimetals based on Mn 3 X(X = Ge, Sn, Ga) kagome compounds exhibit the same ferromagnetic-like responses, including anomalous Hall, Nernst, and magneto-optical effects, as recently discussed for altermagnets. Driven by the Berry curvature due to Weyl fermions, these materials show a disproportionately large magnitude of electromagnetic effects even in the absence of large magnetization. For applications it is crucial to realize these responses in a wide range of temperatures both below and above 300 K. While stoichiometric Mn 3 X materials do not offer optimal performance, we show that Mn 3 Sn 1−x Ga x sputtered films with a variable composition offers a tunable Néel temperature, T N ≈ 425 ± 6–500 ± 15 K, which is crucial for device applications, together with a large tunable anomalous Hall effect. Our thin film growth method enables continuous and precise control over the film composition between x = 0 and x = 1. Through a detailed magnetization and Hall transport, we establish the magnetic phase diagram for the hexagonal Mn 3 Sn 1−x Ga x . Our results reveal an enhanced T N and antichiral magnetic phase in Ga-doped Mn 3 Sn and an enhanced anomalous Hall magnitude in Sn-doped Mn 3 Ga compared to their stoichiometric undoped forms. Our work demonstrates a route to optimize the technologically relevant antiferromagnets for various applications.

Magnetic properties and materials↗
DOE OSTI2014

Solid waste bin detection and classification using Dynamic Time Warping and MLP classifier

Highlights: • Solid waste bin level detection using Dynamic Time Warping (DTW). • Gabor wavelet filter is used to extract the solid waste image features. • Multi-Layer Perceptron classifier network is used for bin image classification. • The classification performance evaluated by ROC curve analysis. - Abstract: The increasing requirement for Solid Waste Management (SWM) has become a significant challenge for municipal authorities. A number of integrated systems and methods have introduced to overcome this challenge. Many researchers have aimed to develop an ideal SWM system, including approaches involving software-based routing, Geographic Information Systems (GIS), Radio-frequency Identification (RFID), or sensor intelligent bins. Image processing solutions for the Solid Waste (SW) collection have also been developed; however, during capturing the bin image, it is challenging to position the camera for getting a bin area centralized image. As yet, there is no ideal system which can correctly estimate the amount of SW. This paper briefly discusses an efficient image processing solution to overcome these problems. Dynamic Time Warping (DTW) was used for detecting and cropping the bin area and Gabor wavelet (GW) was introduced for feature extraction of the waste bin image. Image features were used to train the classifier. A Multi-Layer Perceptron (MLP) classifier was used to classify the waste bin level and estimate the amount of waste inside the bin. The area under the Receiver Operating Characteristic (ROC) curves was used to statistically evaluate classifier performance. The results of this developed system are comparable to previous image processing based system. The system demonstration using DTW with GW for feature extraction and an MLP classifier led to promising results with respect to the accuracy of waste level estimation (98.50%). The application can be used to optimize the routing of waste collection based on the estimated bin level.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Optimal sensing on an asymmetric exceptional surface

We study the connection between exceptional points (EPs) and optimal parameter estimation, in a simple system consisting of two counterpropagating traveling wave modes in a microring resonator. The unknown parameter to be estimated is the strength of a perturbing cross-coupling between the two modes. Partially reflecting the output of one mode into the other creates a non-Hermitian Hamiltonian that exhibits a family of EPs, creating an exceptional surface (ES). We use a fully quantum treatment of field inputs and noise sources to obtain a quantitative bound on the estimation error by calculating the quantum Fisher information (QFI) in the output fields, whose inverse gives the Cramér-Rao lower bound on the mean-squared error of any unbiased estimator. We determine the bounds for two input states, namely, a semiclassical coherent state and a highly nonclassical NOON state. We find that the QFI is enhanced in the presence of an EP for both of these input states and that both states can saturate the Cramér-Rao bound. We then identify idealized yet experimentally feasible measurements that achieve the minimum bound for these two input states. We also investigate how the QFI changes for parameter values that do not lie on the ES, finding that these can have a larger QFI, suggesting alternative routes to optimize the parameter estimation for this problem.

Exceptional points↗
DOE OSTI2017

Quality Optimization of Commercial FeCrAl Tube Production

The objectives of this report are to summarize the various process parameters and conditions that trigger premature failures during the production steps for Generation II ATF FeCrAl seamless tubes in commercially available manufacturing processes, and to suggest optimized processing routes and parameters to improve the quality and the material yield of commercial tube production. The production process steps include (1) the heat production process, (2) the master bar production process, and (3) the tube reduction process. For heat production, not only chemical composition control but also elimination of solidification defects in the vacuum induction–melted ingot are key. A hot-isostatic press helped in reducing and eliminating the internal, preexisting cracks in the ingot, which could be a source of premature failure (e.g., crack initiation from oxide particles) in the latter part of the tube production process. The master bars were produced by a hot-extrusion process. The area reduction ratio and the extrusion temperature are key to controlling the quality of the master bars and the grain structure. Because of the limited deformation ability of FeCrAl alloys, especially at ambient temperatures, a controlled, uniform grain structure with relatively small grains (<100 µm) is required at the beginning of the tube reduction process. Furthermore, a relatively small amount of area reduction per pass, combined with controlled inter-pass annealing, is important to achieve a reduction in failure events, a highly uniform wall thickness, concentricity, and a high-quality surface finish. Based on the knowledge obtained regarding process conditions, FeCrAl tube production with optimized process parameters is currently in progress. A portion of the final tube inventory was delivered in late June 2017. Cross-sectional microstructural characterization was completed for screening the quality of as-received tubes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗