Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Feed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

sCO2 Primary Power Large-Scale Pilot Plant FEED Summary

Echogen Power Systems and its project partners the Electric Power Research Institute, CDM Smith, Riley Power Inc. (a Babcock Power Inc. company), and the University of Missouri completed the Front-End Engineering Design (FEED) study of a nominal 10 MWe supercritical carbon dioxide (sCO2) large-scale pilot plant based on Recompression Brayton Cycle (RCBC) architecture. The FEED study was completed under Phase II of the U.S. Department of Energy Fossil Fuel Large-Scale Pilots program. The FEED study scope included the preliminary design of the combustion and environmental control systems, the primary heater, the sCO2 power cycle and its associated turbomachinery, and the balance of plant equipment to determine accurate cost and schedule requirements for fabrication and installation of the system at the University of Missouri’s Combined Cooling, Heat, and Power Plant, located in Columbia, Missouri. The RCBC sCO2 cycle presents superior thermodynamic efficiency compared to steam-Rankine cycles and is adaptable to a broad range of heat sources. The risk aversion of the power generation industry requires a successful large-scale pilot plant demonstration to enable financing and deployment of commercial-scale plants. Therefore, successful construction and demonstration of a 10 MWe RCBC sCO2 power plant would empower a transformational step forward for the efficiency of the next generation of utility power plants. This paper provides details on the primary heater, environmental control systems, and sCO2 power cycle design and performance.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Optimizing feed modulation for coupled methane and NO x conversion over Pd-Pt/Mn 0.5 Fe 2.5 O 4 /Al 2 O 3 monolith catalyst

Here the impacts of feed modulation (frequency, amplitude) and catalyst design (composition and architecture) parameters are reported for the conversion of methane and NO x over a dual-layer Pt+Pd/Al 2 O 3 + Mn 0.5 Fe 2.5 O 4 /Al 2 O 3 monolith. CH 4 and NO x conversion data show that the dual-layer catalyst outperforms single-layer samples having the same catalyst loadings, with and without spinel. Close proximity of the PGM and MFO functions in the mixed-layer catalyst lowers the CH 4 conversion at high temperature while separating the PGM and spinel layers with an intermediate Al 2 O 3 layer does not. Methane conversion enhancement is linked to its nonmonotonic dependence on O 2 . The performance gains are tied to a transient activity spike that occurs during the lean-to-rich feed transition when water is present in the feed. The transient spike is attributed to the removal of CO and H 2 products via reactions with stored O 2 in the spinel, eliminating inhibition of methane steam reforming.

03 NATURAL GAS↗
DOE OSTI2026

Computational flow modeling of triply periodic minimal surfaces as feed channel spacers in ultra-high pressure reverse osmosis applications

Triply periodic minimal surfaces (TPMS) are a special class of mathematical surfaces characterized by a high surface area-to-volume ratio. They have generated considerable interest in fields such as acoustics, heat transfer, and membrane-based filtration processes. This study evaluates the performance of four different TPMS designs—Schoen Gyroid, Schoen Crossed Layers of Parallels (CLP), Schoen Transverse Crossed Layers of Parallels (tCLP), and Schwarz-Primitive—when used as feed channel spacers under ultra-high pressure reverse osmosis (UHPRO) conditions, at approximately 200 bar. Our experimentally validated computational fluid dynamics model reveal different flow patterns within the feed channels for each of the four TPMS designs, leading to varying hydrodynamic and permeation properties. Under the simulated UHPRO conditions, the Gyroid and tCLP designs yield up to a 23% increase in average permeate velocity and a 14% reduction in average membrane-surface concentration relative to a non-woven spacer of the same porosity. Furthermore, the enhanced performance comes with an increased feed channel pressure drop, although it only constitutes less than 4% of the operating pressure when extrapolated for a meter-long membrane module. Additionally, the study analyzes the effects of varying inlet velocity and spacer porosity on membrane performance. Overall, this research provides valuable insights into the potential use of TPMS spacers in UHPRO applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Alternative reductants for foam control during vitrification of high-iron High Level Waste (HLW) feeds

Foaming during vitrification of radioactive waste in Joule-Heated Ceramic Melters (JHCM) is exacerbated by trapping of evolving gases, such as CO 2 , NO x and O 2 , beneath a viscous reaction layer. Foaming restricts heat transfer during melting. Sucrose is employed as the baseline additive at the Hanford site in Washington State, USA to reduce foaming. Alternative carbon-based reductant additives were explored in simulated, inactive Hanford high-iron HLW-NG-Fe2 feeds, for both their effect on foaming and to give insight to the behaviour of multivalent species in glass melts under different redox conditions. Graphite, coke (93% C), formic acid and HEDTA additives were compared with sucrose, and a feed with no additive. Graphite and coke additions proved most effective in reducing the maximum foam volume by 51 ± 3% and 54 ± 2%, respectively, compared with 24 ± 5% for sucrose. Lower foaming could result in more efficient vitrification in JHCMs. Reductants also affected redox ratios in the multivalent species present in the feed. The order of reduction, Mn 3+ /Mn 2+ > Cr 6+ /Cr 3+ > Ce 3+ /Ce 4+ > Fe 3+ /Fe 2+ was as predicted on the basis of their redox potentials. There is less reduction overall, particularly in the Fe 3+ → Fe 2+ , than predicted by the calculations, attributed to the oxygenated atmosphere of the experiments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Acquisition of Rickettsia rickettsii (Rickettsiales: Rickettsiaceae) by Haemaphysalis longicornis (Acari: Ixodidae) through co-feeding with infected Dermacentor variabilis (Acari: Ixodidae) in the laboratory

Abstract Haemaphysalis longicornis (Neumann) is an invasive ixodid tick originating from eastern Asia which recently has become established in the United States. In its native range, this tick can transmit several pathogens to animals and humans, but little is known about its ability to acquire and transmit pathogens native to the United States. Geographic overlap with ticks such as Dermacentor variabilis (Say), a known vector of Rickettsia rickettsii, makes investigation into the interactions between H. longicornis and D. variabilis of interest to the public health community. Previous studies have shown that H. longicornis can serve as a competent vector of R. rickettsii under laboratory settings, but there is little information on its ability to acquire this pathogen via other biologically relevant routes, such as co-feeding. Here, we assess the ability of H. longicornis nymphs to acquire R. rickettsii through co-feeding with infected D. variabilis adults on a vertebrate animal model under laboratory conditions. The median infection prevalence in engorged H. longicornis nymphs across 8 cohorts was 0% with an interquartile range (IQR) of 4.13%. Following transstadial transmission, the median infection prevalence in flat females was 0.7% (IQR = 2.4%). Our results show that co-feeding transmission occurs at low levels in the laboratory between these 2 species. However, based on the relatively low transmission rates, this may not be a likely mechanism of R. rickettsii introduction to H. longicornis.

Entomology↗
DOE OSTI2020

Technical Gaps in Hanford High-Level Waste Solids Settling Behavior and Settling Time Evaluation for Direct Feed High-Level Waste (DFHLW) Operations

Settling of high-level waste (HLW) solids in process vessels is a key conceptual process step in providing HLW feed directly to the Hanford Waste Treatment and Immobilization Plant (WTP) HLW Vitrification Facility. Direct Feed High-Level Waste (DFHLW) is a potential approach to initiating HLW vitrification prior to completing of the WTP Pretreatment Facility. Settling would be used with subsequent supernatant decant to concentrate HLW feed. To support planning for DFHLW, Washington River Protection Solutions (WRPS) requested support from the Pacific Northwest National Laboratory to evaluate the current data set available to predict the time needed for HLW solids to settle, to identify gaps in the understanding and predictive capability of HLW solids waste settling times, and to provide scoping estimates of the potential settling time. Eight technical gaps were identified for predicting settling times and characteristics of the formed sediment layers including: Gap 1: In-Tank Settling Rates Faster than Settling of Laboratory Samples, Gap 2: Effect of Sludge Leaching/Washing on Predicted Settling Times, Gap 3: Predicting Waste Settling from Waste Chemistry (Waste Type), Gap 4: Predicting Waste Settling from Particle Size and Density Distributions (PSDDs), Gap 5: Insufficient Laboratory and In-Tank Settling Data to Represent Hanford Waste, Gap 6: Methods for Real-Time, In-Tank Tracking of Settling, Gap 7: Prediction of Sediment Erosion Resistance as a Function of Settling Time, and Gap 8: Prediction of Sediment Solids Content as a Function of Settling Time. In addition to the data gaps, an overarching observation of the settling rate and settled layer data is the significant variation in behavior. At similar solids concentrations, settling rates can vary by as much as 3 orders of magnitude depending on the source waste tank, and significantly different settling rates are noted between laboratory and in situ tests for the same waste tank. The range of average solids concentration in existing HLW sediment, which may have been quiescent for decades, can vary from less than 7 wt% to greater than 74 wt% solids. The shear strengths (or yield stresses) measured on laboratory samples range from less than 27 Pa to greater than 6400 Pa. These variations can challenge process planning for the application of a settle/decant process for DFHLW. This report describes the significance of the gaps to the settle/decant process and presents uncertainties by way of examples. Potential technical approaches for resolving these gaps are described and the estimated difficulty in resolving these gaps is evaluated. Based on the significance of the gap and the difficulty of resolution, recommendations are made to address specific gaps. Scoping estimates of the potential settling times for DFHLW solids have been made based on the existing data set with its associated gaps. Depending on the process vessel depth and final sediment concentration, substantial fractions of the scoping estimate results for settling times for characterized HLW exceed the 2-week period that has been previously assumed for process planning. There is also significant disparity, potentially greater than a factor of 5000 difference, in the estimated settling times depending on process vessel depth and final sediment solid concentration. This variation in results underscores the significance of the identified gaps and uncertainties with respect to process planning for utilizing settle/decant operations for DFHLW.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Technical Information Needs and Regulatory Considerations for Front-End Transportation Activities of HALEU Fuel Feed Material

This report fulfills task order number 31310022F0033 Task 1 Assessment of technical information needs and considerations for front-end transportation activities for HALEU fuel feed material. This assessment primarily focuses on the transportation outlook and packaging requirements for transporting high-assay low-enriched uranium (HALEU) fuel feed material. The regulatory framework is described in section 3.0. In section 4.0 the specific issues associated with reviewing HALEU feed material packages are discussed. The rest of the report discusses the need for new packages and Department of Energy progress on HALEU production. Through this evaluation it is shown that the 5% enrichment barrier between low-enriched uranium and HALEU is a significant challenge to transportation packaging. However, there are licensed designs and concepts that can be used to transport HALEU feedstock. No significant issues were identified through the HALEU range up to 20% enriched.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Compositional Variation Tests on DuraMelter 100 with LAW Sub-Envelope B1 Feed in Support of the LAW Pilot Melter, VSL-02R62N0-5, Rev. 0 (May 2003)

The principal objective of the DM100 tests was to demonstrate the robustness of the vitrification process with respect to feed and glass compositional changes resulting from variations in the simulant-to-additive ratio. The DM100-WV unit was selected for these tests; this melter was used for all of the Part B 1 tests on LAW Envelopes A, B, and C sulfate incorporation that were used to support the subsequent tests on the Pilot Melter as well as for the more recent LAW Sub-Envelope Al, A2, A3 and Cl tests. The same melter was selected for the present tests in order to maintain comparisons between the data sets. In addition, the somewhat smaller glass volume for the same melt surface area as compared to the DM100-BL melter means that more glass turnovers are achieved for a given test duration. The DM100 tests used nominal feed and feed with a 15% surplus in waste simulant. Previous Pilot Melter tests on Envelope A with 10% variations (but with sulfate removal) showed significant impacts on glass production rates that were ultimately corrected by adjustments in the sugar additions. Consequently, robustness with respect to throughput as well as sulfate tolerance are important motivations for these tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Compositional Variation Tests on DuraMelter 100 with LAW Sub-Envelope C2 Feed in Support of the LAW Pilot Melter (Final Report)

One of the principal objectives of the DM100 melter tests was to demonstrate that the LAW Sub-Envelope C2 feeds with ± 15% variations in the amounts of waste simulant are suitable for large-scale tests on the LAW Pilot melter. The other principle objective for the DM100 tests was to determine the relative effects of sugar versus waste organics on glass redox state, NOx emissions, sulfur emissions, sulfur retention in the glass, secondary sulfate layer formation, and glass-melt foaming. Additional objectives included measurement of the feed rheological properties and collection of melter emissions data. Screening tests are conducted at the DM100 scale in order to identify and correct potential problems before testing at the larger scale LAW Pilot melter. Testing goals were met in that the results of the DM100 melter test resulted in selection of LAW Sub-Envelope C2 feed suitable for Pilot Melter testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

FEED Study of CarbonCapture Inc DAC and CarbonCure Utilization Technologies Using United States Steel’s Gary Works Plant Waste Heat (Final Report)

The University of Illinois at Urbana-Champaign (UIUC) led this project to produce a front-end engineering design (FEED) study of an advanced Direct Air Capture and Utilization System (DACUS) system that can remove a minimum of 5,000 tonnes/yr net of carbon dioxide from air (based on cradle-to-gate LCA) and utilizing the CO 2 to produce low carbon intensity ready mix concrete. The designed system, if built, would be larger than any currently existing Direct Air Capture (DAC) collector in the U.S. Such carbon capture technologies are critical to meeting the goals of the DOE’s program to accelerate climate-critical technology. In addition to the power sector, industrial facilities for the manufacture of steel and cement/concrete are among the major sources of anthropogenic CO 2 . DAC is a promising new technology for reducing CO 2 , a potent greenhouse gas, in the atmosphere but is expensive, in part due to the energy required to adsorb and desorb captured CO 2 during cycles. By integrating CarbonCapture Inc. (CCI) DAC modules at United States Steel's Gary Works (USS) and utilizing the site's waste heat, energy, and location this project evaluates the feasibility of utilizing the captured CO 2 and the logistics of transportation. CarbonCapture Inc. has developed an innovative DAC system using novel adsorbents to cost-effectively capture CO 2 . The captured, liquified gas will be trucked to ready-mix concrete plants within the region, the closest of which is approximately 3.5 miles away, where CarbonCure will inject it into concrete during the mixing process at the facilities. The carbon dioxide reacts with concrete, mineralizing into calcium carbonate (CaCO 3 ), permanently locking the greenhouse gas into the matrix of the building material. This FEED study demonstrated a full CO 2 value chain for DACUS from industrial facilities. It also provided a means for Visage Energy Corp. (Visage) to assess the impact of this holistic approach on job creation, regional economic impact, and environmental justice. The project team also included Sargent & Lundy (S&L) to provide the constructability review and costing of the integration of the DAC with the steel plant. Ecotek Engineering USA, LLC designed the outside battery limit (OSBL) infrastructure to connect the DAC and the plant. Activities performed during the project included: (1) Project Management Plan; (2) Technology Maturation Plan (TMP); (3) Initial Workforce Readiness Plan; (4) Workforce Readiness Plan; (5) Front-End Engineering Design (FEED) Study; (6) Project Design Basis; (7) Hazards and Operability (HAZOP) Study; (8) Constructability Review; (9) Project Cost Assessment; (10) Logistics Analysis of CO 2 Transportation to the Utilization Site; (11) Business Case Analysis; (12) Life Cycle Analysis (LCA); (13) Environmental Health and Safety (EH&S) Analysis; (14) Environmental Justice Analysis; and (15) Economic Revitalization and Job Creation Outcomes Analysis. This report provides a summary of the outcomes and results of the project, which was performed between Oct. 1, 2022, through Sept. 30, 2024.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Iodine Speciation Effects in LAW Feeds

Tests were conducted on a DM10 vitrification system with prototypical off-gas treatment system, which includes an SBS, WESP, and evaporator based on the design of the evaporator to be installed at the WTP for concentration of the liquid effluents. This allowed determination of the partitioning and speciation of iodine between the melter and the off gas system components, including liquid effluents from the SBS and WESP as well as in the evaporator condensate and concentrate. Evaporator testing was decoupled from melter testing to permit filtration and pH adjustments of process solutions prior to evaporation. In addition, a slip stream was pulled from the exhaust downstream of the WESP and High-Efficiency Particulate Air (HEPA) filters and passed through a caustic scrubber simulating the WTP caustic scrubber to assess iodine partitioning to the caustic scrubber liquid effluent. The tests were conducted using simulated Hanford LAW from tank AP-107, which is the planned first feed for Direct Feed LAW (DFLAW) operations, at a nominal feed concentration of 5.6 molar Na over about 120 hours of testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Filtration Performance of Simulated 200 West Area Waste Feeds

This report describes the scaled experimental system and approach used to examine dead-end filtration performance of representative 200W waste feeds. The scaled system, which was originally designed and assembled to test Tank Side Cesium Removal (TSCR) system performance with higher-than-expected solid loadings in 2021 (Schonewill et al. 2021), was repurposed to conduct the current experiments at ~1/145 of full scale (based on throughput). Six experimental runs were conducted with five different 200W waste feed simulants: three using a DEF module scaled for TSCR and three using a DEF module scaled for the 200W process modules (based on the current design for the Advanced Modular Pretreatment System). Each experiment was run continuously for multiple days with an operating approach prototypic of the full-scale system. Staff performing the experimental runs monitored performance, obtained data from calibrated process instruments, and collected samples for observation and analysis. The measured data are presented with a focus on assessing DEF performance – specifically, the filters’ differential pressure response to the five waste simulants, frequency and efficacy of backwashing, and baseline recovery between experimental runs; data related to ion exchange column performance are also discussed in cases where the opportunity arose. The experimental campaign demonstrated that the DEFs satisfied their primary function of protecting the ion exchange column from solid intrusion for all the representative simulants used. The filters readily handled solids loadings of =500 ppm (and even greater), especially the modules scaled to the 200W process modules. Adjustments to the processing flow rate and reductions in feed temperature were observed to affect the rate of differential pressure increase on the filters, but neither adversely affected the ability of the DEFs to perform their primary function. Backflushing reliably recovered filter performance in all runs, although it did not prevent irreversible fouling for one simulant. The run that exhibited irreversible fouling established that both the quantity and the nature of the solids being filtered need to be considered when projecting filter performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1967

Computer programs for antenna feed system design and analysis

Fourteen computer programs have been developed for antenna feed system design and analysis. The programs cover a large spectrum of feed design problems, from primary feed pattern synthesis to the farfield pattern of the main reflector, including analyses of structural distortions.

Ludwig, A.↗
NASA NTRS1968

Dual wire weld feed proportioner

Dual feed mechanism enables proportioning of two different weld feed wires during automated TIG welding to produce a weld alloy deposit of the desired composition. The wires are fed into the weld simultaneously. The relative feed rates of the wires and the wire diameters determine the weld deposit composition.

Nugent, R. E.↗
NASA NTRS1969

Multi-feed cone for Cassegrainian antenna

Multiple-cone feed horn system for a cassegrainian antenna using a rotable hyperboloid in conjunction with a multiple cone system is possible by moving hyperboloid relative to fixed multiple feeds and paraboloid. The hyperboloid can be adjusted so that, for each feed, it is in the best possible position.

Stelzried, C. T.↗
NASA NTRS1972

Propellant feed systems transients

Program was written to assist in analysis of fluid feed line transients initiated by operation of valves. Program output consists of printout of transient pressures and velocities through feed system as function of time. Optional CRT plot output provides for display of transient pressures and velocities as function of time at any desired location in feed system.

Shumway, R. A.↗
NASA NTRS1972

Pioneer F/G feed movement mechanism

The Pioneer F/G spacecraft achieves the desired earth-pointing direction through a system requiring the shifting of the main antenna feed 1 in. off axis. The feed is pivoted to this position by an electrically heated thermal actuator consisting of an electroless nickel bellows in a copper housing and filled with Freon 21. The actuator overtravels and maintains the feed in the offset position in a thermostatic limit cycle operation mode until commanded off. The mechanism is expected to operate in a -240 F environment near Jupiter and was successfully tested at such temperatures.

R. M. Acker↗
NASA NTRS1974

Dual frequency dichroic feed performance

The NASA Deep Space Net (DSN) in support of the Viking Mars Project in 1976, and for science and technology demonstrations during the Mariner-Venus-Mercury mission in 1974, has developed and implemented a dual (S- and X-band) feed for large ground microwave antennas. This feed provides for a multiplicity of functions; very low listening capability at each downlink (spacecraft-to-earth) band as well as simultaneous diplexed very high cw power uplink (earth-to-spacecraft) at the S-band frequency. Total 64-m antenna system performance, is considered in terms of gain, operating noise temperature and dual beam pointing or boresight coincidence. Because of the unique ability to fold or stow the dual band feed elements for single band operations, the performance definition between single and dual band operations will be reliable and accurate.

Bathker, D. A.↗