Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TABLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,405 records · Page 78

SCA Test Report: H4RG-21319 WFIRST

This report summarizes the measured performance for the Sensor Chip Assembly (SCA), which is identified in Table 1. The SCA architecture is a substrate-removed HgCdTe detector with an area of 4096x4096 pixels (with a reference pixel area of four pixels deep around all four sides, available to substitute corresponding image pixels) and a pixel pitch of 10 µm. This SCA has been tested at the Goddard Space Flight Center (GSFC/NASA) Detector Characterization Laboratory (DCL). Teledyne (the vendor) classifies its detectors into different grades based on testing performed at its facility. The classification of this SCA and the tested dates are included in Table 1 below. The tests performed on this array are derived from the document WFIRST-PROC-09220_WFIRST-SCA-ATP_-.docx. A summary of the test parameters, requirements, and test results is presented in Table 2. The details of each test are subsequently described in the report. In the Summary (Table 2), SCA results are reported at an operating temperature of 95K, and 1.0 V bias voltage. In the detailed section of each test, the results for 95 K and 0.5V bias voltage is also reported. The data for the result reported in this document was acquired in pixel reset mode. For all cases, the frame time used is 2.830 seconds. Reference pixel correction was applied to every raw frame.

Laddawan Miko↗

Modal Test and Model Correlation of NASA Plum Brook Station Mechanical Vibration Facility Head Expander –Lessons Learned from the Perspective of an Early-Career Engineer

In preparation for the Sierra Nevada Corporation’s (SNC) Dream Chaser spacecraft vibration test campaign at the Mechanical Vibration Facility (MVF) at NASA Plum Brook Station (PBS) in Sandusky, Ohio, a test-verified model of MVF is needed in order to be able to perform accurate pretest analysis used for determining response limits and abort levels. MVF was designed to vibration test MPCV Orion and was used to perform the system level vibration test of the European Service Module Structural Test Article (E-STA) in 2016. MVF is comprised of an 18 ft diameter annulus table that is driven with sixteen hydraulic vertical actuator assemblies and four hydraulic horizontal actuator assemblies, which allow it to perform single axis vibration testing in the vertical axis and in each of the two orthogonal horizontal axes without the need for reconfiguring the test article. A head expander for the MVF Table has been designed and built that fills in the center opening providing a continuous flat mounting surface with a maximum diameter of 16.25feet that expands the vibration testing capabilities of MVF. The MVF Table with this head expander will be used during the SNC Dream Chaser spacecraft vibration test campaign. Therefore, a critical element in a test-verified model of the MVF will be a test correlated finite element model (FEM) of the head expander. To obtain this, engineers from the Structural Dynamics Lab (SDL) at NASA Glenn Research Center (GRC) in Cleveland, Ohio performed a modal pretest analysis, conducted a modal test in July 2019, and most recently correlated the head expander finite element model to the modal test data up to 300 Hz. From the initial test preparations to the final delivery of a correlated finite element model, all efforts mentioned were led by the same early-career engineers at NASA GRC. From the viewpoint of an early-career engineer, lessons learned about modal pretest analysis, modal testing, and finite element model correlation of the MVF Table expander head will be presented and discussed. This will include the importance of understanding the limitations of using uncorrelated finite element models in the modal pretest analysis and planning, the importance of orthogonality metrics in judging adequacy and accuracy of test mode shapes, and the importance of having the FEM match the as built hardware in the model correlation effort.

Emma L Pierson↗

Applications of the Dynamic N-Dimensional K-Vector

The n-dimensional k-vector (NDKV) is an appealing alternative to binary tress for resolving complex queries in large relational databases. The method has excelled in several applications involving static databases. The present paper extends the theory supporting the NDKV to handle dynamic databases, where the data is updated frequently. This includes deleting records, adding new entries, or editing existing elements. The merit of this new version of the NDKV, the dynamic n-dimensional k-vector (DNDKV), is that it is no longer necessary to recompute the entire k-vector (the main structure that indexes the data) every time a record changes. The algorithm updates the four constituents of the standard NDKV on the fly: the database, sorted database, index, and k-vector tables. As a result, the DNDKV becomes comparable in terms of capabilities and flexibility to stateof-the-art storage engines relying on structured query languages (SQL). The performance of the DNDKV is assessed by running typical read/write operations on a database that contains millions of pre-computed missions to celestial bodies. This database requires frequent updates whenever an orbit solution is refined or new bodies are discovered. The DNDKV is faster than rebuilding the k-vector tables completely, provided that the number of elements being added or removed is not excessively large. Direct runtime comparisons with MySQL suggest that the DNDKV is several times faster for reading but might be slower for writing and updating the database. One limit of the technique is the elements being added must be within the range of the current k-vector tables. If this is not the case, the technique cannot be used and the k-vector tables must be rebuilt from scratch.

Mortari, Daniele↗

SCA Test Report H4RG-21645 Roman Space Telescope

This report summarizes the measured performance for the Sensor Chip Assembly (SCA), which is identified in Table 1. The SCA architecture is a substrate-removed HgCdTe detector with an area of 4096x4096 pixels (with a reference pixel area of four pixels deep around all four sides, available to substitute corresponding image pixels) and a pixel pitch of 10 μm. This SCA has been tested at the Goddard Space Flight Center (GSFC/NASA) Detector Characterization Laboratory (DCL). Teledyne (the vendor) classifies its detectors into different grades based on testing performed at its facility. The classification of this SCA and the tested dates are included in Table 1 below. The tests performed on this array are derived from the document WFIRST-PROC-09220_WFIRST-SCAATP_-.docx. A summary of the test parameters, requirements, and test results is presented in Table 2. The details of each test are subsequently described in the report. In the Summary (Table 2), SCA results are reported at an operating temperature of 95K, and 1.0 V bias voltage. In the detailed section of each test, the results for 95 K and 0.5V bias voltage is also reported. The data for the result reported in this document was acquired in pixel reset mode. For all cases, the frame time used is 2.830 seconds. Reference pixel correction was applied to every raw frame.

Laddawan Miko↗

SCA Test Report H4RG-21813: Roman Space Telescope

This report summarizes the measured performance for the Sensor Chip Assembly (SCA), which is identified in Table 1. The SCA architecture is a substrate-removed HgCdTe detector with an area of 4096x4096 pixels (with a reference pixel area of four pixels deep around all four sides, available to substitute corresponding image pixels) and a pixel pitch of 10 μm.This SCA has been tested at the Goddard Space Flight Center (GSFC/NASA) Detector Characterization Laboratory (DCL). Teledyne (the vendor) classifies its detectors into different grades based on testing performed at its facility. The classification of this SCA and the tested dates are included in Table 1 below. The tests performed on this array are derived from the document WFIRST-P ROC-09220_WFIRST-SCA-ATP_-.docx.A summary of the test parameters, requirements, and test results is presented in Table 2. The details of each test are subsequently described in the report. In the Summary ( Table 2), SCA results are reported at an operating temperature of 95K, and 1.0 V bias voltage. In the detailed section of each test, the results for 95 K and 0.5V bias voltage is also reported. The data for the result reported in this document was acquired in pixel reset mode. For all cases, the frame time used is 2.830 seconds. Reference pixel correction was applied to every raw frame.

Laddawan Miko↗

SCA Test Report H4RG-21814: Roman Space Telescope

This report summarizes the measured performance for the Sensor Chip Assembly (SCA), which is identified in Table 1. The SCA architecture is a substrate-removed HgCdTe detector with an area of 4096x4096 pixels (with a reference pixel area of four pixels deep around all four sides, available to substitute corresponding image pixels) and a pixel pitch of 10 μm.This SCA has been tested at the Goddard Space Flight Center (GSFC/NASA) Detector Characterization Laboratory (DCL). Teledyne (the vendor) classifies its detectors into different grades based on testing performed at its facility. The classification of this SCA and the tested dates are included in Table 1 below. The tests performed on this array are derived from the document WFIRST-P ROC-09220_WFIRST-SCA-ATP_-.docx.A summary of the test parameters, requirements, and test results is presented in Table 2. The details of each test are subsequently described in the report. In the Summary ( Table 2), SCA results are reported at an operating temperature of 95K, and 1.0 V bias voltage. In the detailed section of each test, the results for 95 K and 0.5V bias voltage is also reported. The data for the result reported in this document was acquired in pixel reset mode. For all cases, the frame time used is 2.830 seconds. Reference pixel correction was applied to every raw frame.

Laddawan Miko↗

SCA Test Report H4RG-21815: Roman Space Telescope

This report summarizes the measured performance for the Sensor Chip Assembly (SCA), which is identified in Table 1. The SCA architecture is a substrate-removed HgCdTe detector with an area of 4096x4096 pixels (with a reference pixel area of four pixels deep around all four sides, available to substitute corresponding image pixels) and a pixel pitch of 10 μm.This SCA has been tested at the Goddard Space Flight Center (GSFC/NASA) Detector Characterization Laboratory (DCL). Teledyne (the vendor) classifies its detectors into different grades based on testing performed at its facility. The classification of this SCA and the tested dates are included in Table 1 below. The tests performed on this array are derived from the document WFIRST-PROC-09220_WFIRST-SCA-ATP_-.docx.A summary of the test parameters, requirements, and test results is presented in Table 2. The details of each test are subsequently described in the report. In the Summary (Table 2), SCA results are reported at an operating temperature of 95K, and 1.0 V bias voltage. In the detailed section of each test, the results for 95 K and 0.5V bias voltage is also reported. The data for the result reported in this document was acquired in pixel reset mode. For all cases, the frame time used is 2.830 seconds. Reference pixel correction was applied to every raw frame.

Laddawan Miko↗

Models, In situ, and Remote Sensing of Aerosols (MIRA)

There is a natural partitioning of scientific interest amongst three specialties of aerosol re-search: modeling, in situ measurements, and remote sensing. The broader aerosol community benefits when these groups interact, and this strengthens overall scientific impact on climate and air quality research and predictions. The new MIRA working group establishes a forum for identifying collaborations and improving discussions amongst specialties and across regional boundaries. One area of keen interest is uniting satellite and ground-based lidar groups with other aerosol disciplines. Elastic backscatter lidars depend upon a priori knowledge of aerosol properties to convert measured lidar profiles into aerosol extinction profiles. Acquiring additional insight on aerosol properties and transport is highly valuable to these lidar groups to improve the data quality and aid in their scientific interpretation. Another area of interest is to facilitate the incorporation of measurements into global aerosol models. Modelers need aerosol optical look-up tables that enable quick conversions of hydrated (and dry) polydisperse size distributions into aerosol optical properties (extinction, scattering, etc.), but many of the existing tables are based upon outdated measurements. Thus, MIRA is building the Tables of Aerosol Optics (TAO), which is a community collection of aerosol optical calculations. This expands on the historical efforts of Shettle and Fenn, d’Almeida, GADS, OPAC, etc., except that TAO seeks continual input from the community. Thus, as aerosol measurement and computational techniques advance, so does the TAO collective. Since TAO is a community collective, it is expected that users will optionally upload computations for aerosol type as well as computations for all of the traditional aerosol species(like amm sulfate, amm nitrate, organics, etc.). The near-term purpose of the MIRA working group is to: *Characterize regional aerosol lidar ratios to support improvements of aerosol extinction profiles and understanding of aerosol typing. *Create TAO --a community cooperative of aerosol optical tables. *Facilitate international communications between aerosol measurement and modeling groups. *Encourage the use of regional knowledge to develop and improve remote sensing techniques for current and future backscatter lidars located in space. *Enable and foster communication between the scientists who run global aerosol models and scientists who analyze space-based lidar data. We will discuss how a collaborative aerosol working group will be organized on this topic. Those who are interested in MIRA can sign up for the MIRA email listserver at https://forms.gle/qdbCnngzNJc5YJi57.

Greg Schuster↗

Deep Neural Network Based Unsteady Flamelet Progress Variable Approach in a Supersonic Combustor

Higher dimensional flamelet manifolds are essential in capturing the coupled effects of pressure gradients and unsteady chemical kinetics observed in supersonic combustion applications. Previous studies have validated the feasibility of using deep neural networks as an alternative to computation-ally intensive multidimensional flamelet table storage and lookup. This approach has demonstrated a significant reduction in memory footprint and enabled the use of larger dimensional tabulated manifolds for supersonic combustion in canonical problems. In this study, the Unsteady Flamelet Progress Variable (UFPV)-ANN model implemented in the VULCAN-CFD code is validated by the Burrows-Kurkov supersonic mixing/combustion configuration. The well characterized experimental problem consists of hydrogen injection into a supersonic vitiated crossflow that results in a lifted flame structure. The initial model consists of a 4-dimensional table where the independent variables Z, C, Xst, P are tabulated using an unsteady flamelet code with boundary conditions corresponding to the vitiated air conditions. The results show the development of a lifted flame structure and over-all acceptable agreement with finite-rate chemistry (FRC) simulation and the experimental data. Moreover, direct mapping between the independent variables and the flamelet table is replaced by a deep neural network for significant memory reduction. The results indicate that the UFPV-ANN approach can retrieve the same solution as the memory intensive lookup table approach.

Flamelet↗

Microbial Monitoring of New Cleanrooms Used to Curate Astrobiologically Relevant Asteroid Samples from Bennu and Ryugu

Introduction: NASA has constructed two new cleanrooms to house materials from the OSRIS-REx and Hayabusa2 missions to the asteroids Ryugu (162173) and Bennu (101955), respectively. In accordance with standard astromaterials curation practices, these cleanrooms will be monitored for particulate contamination and maintained to ISO 5 equivalent standards1. Since the samples in these collections are expected to contain prebiotic organic compounds that may help explain the origin of life on Earth, these labs will also be monitored for organic and biological contamination2. Samples from Ryugu arrived on Earth in December, 2020. After basic characterization in Japan, NASA received a subset of these samples at the astromaterials curation facility in Houston in December of 2021. OSIRIS-REx is expected to return samples in September, 2023. Here we present preliminary microbial monitoring results from monthly monitoring of these new labs and the connected microtomy and staging areas that support them, as they are being commissioned. We also compare these results to baseline values for other astromaterials curation labs. We will also briefly describe additional cleaning efforts employed to reduce the bioburden in these new cleanrooms. Methods: Microbial samples were collected from surfaces using a dry macrofoam swab (Puritan Brand 2518051PFRNDFD). Swabs were also opened in the lab but not touched to any surfaces to function as negative controls. Samples and controls were processed inside a class II biosafety cabinet to avoid inadvertent cross contamination. The swabs were suspended in 15 ml of PBS (Phosphate Buffered Saline) and vortexed for 20 seconds to remove cells from the swab surface. The PBS was used to inoculate Petri dishes filled with TSA (Tryptic Soy Agar), Blood Agar, or Reasoners 2 agar to check for microbial growth. Each plate was inoculated with 0.1 ml of PBS. The TSA and blood agar plates were incubated at 35˚C and the Reasoners 2 agar plates were incubated at 25˚C for seven days. Petri dishes filled with Potato dextrose agar, Saboraud dextrose agar, or Saboraud dextrose agar with 0.1 mg/ml of chloramphenicol, an antibiotic, were used to check for fungal growth. These plates were inoculated with 0.3 ml of PBS and incubated at 30˚C. The remaining PBS was frozen at -80 ˚C for DNA sequencing. After incubation, isolates were counted and reisolated for identification. Isolates were identified using the VITEK23 system or by sequencing a portion of the 16S rRNA gene for bacteria or the ribosomal internal transcribed spacer (ITS) for fungi. Sequencing was performed with an ABI 3500 Sanger sequencer. Results: During our initial sampling, six of the seven sites sampled (86%) displayed bacterial or fungal growth. Samples collected from the staging areas and microtomy labs are not included in this calculation since those areas are maintained at a lower ISO 7 equivalent cleanliness standard. A month later, only three of the seven sites (43%) displayed bacterial growth. No fungal growth was detected in the second sampling. Since new equipment had been introduced to the Hayabusa2 lab since the first round of sampling, an additional three sampling sites were included in the second round of sampling. None of these sites displayed microbial growth. These sites will be included in all future sampling efforts. Bacterial isolates have been identified from the following genera at multiple time points: Micrococcus, Staphylococcus, and Bacillus. Isolates from the genera: Microbacterium, Nocardioides, Methylocystis, and Microvirga were identified in the initial sampling, but were not present at later time points. Identification of fungal isolates is in progress. Results are summarized in Table 1. Discussion: The recovery rate or percentage of positive samples4 was initially 86%, which is higher than the median recovery rate for comparable ISO 5 equivalent curation labs like Stardust (33%), Hayabusa (33%), and Cosmic Dust (50%). However, after a month of operation, the recovery rate for these same sites decreased to 43%, which is similar to what we observe in comparable curation cleanrooms with no microbial control requirements. Adding in the new sampling sites further decreases the recovery rate to 30%. With the reduction in recovery rate, we also observed a decrease in microbial diversity. At the first time point, we observed at least 10 different bacterial species and at least two different fungi. This is a higher diversity than the median values for comparable ISO 5 equivalent labs (2-4 isolates per sampling event). After the second sampling, we observed at least 4 bacterial species and no fungi, which is more consistent with comparable labs. We expect the recovery rate and diversity in both labs to continue to decrease as routine operation continues. We will use ultrapure hydrogen peroxide to disinfect equipment and work areas prior to opening any sample containers. Most of the bacterial and fungal isolates were detected on samples from the cleanroom floors. This is consistent with baseline results from other curation labs. Organisms from the genera Bacillus, Staphylococcus, and Micrococcus that were repeatedly detected are common in cleanrooms and on human skin5,6. These organisms are generally thought to be introduced when people enter the cleanroom. Microbacterium, Nocardioides, and Microvirga have also previously been identified in astromaterials cleanrooms, but not as frequently as Bacillus, Staphylococcus, and Micrococcus. Methylocystis is a novel genus in the astromaterials cleanrooms, but it was identified with low accuracy (93% match in the sequenced region of the 16S rRNA gene) and further work is needed to confirm this identification. Microbacterium is a diverse genus with isolates identified from terrestrial and aquatic sediments. Some species of Microbacterium are capable of degrading complex organic compounds found in crude oil. The presence of these bacteria in the OSIRIS REx and Hayabusa2 cleanrooms should be closely monitored. Methylocystis is a genus of methanotrophic bacteria capable of oxidizing methane. If this identification proves to be correct and it is detected again, it should be closely monitored as well. Under nominal operating conditions, samples should not ever encounter the cleanroom floor or other high traffic areas. If we observe an increase in the bioburden in sensitive work areas that appears to be influenced by organism transfer from high traffic areas like the floors, we can employ additional hydrogen peroxide treatments to disinfect high traffic areas. Routine microbial monitoring of these labs will ensure that NASA’s astromaterials collections remain pristine and useful for scientific study. Table 1. Sampling Locations and Colony Counts Bacterial CFUa Fungal CFU Bacterial CFU Fungal CFU Lab - Location 11/2/2021 11/2/2021 12/13/2021 12/13/2021 H2b-Floor 4 8 1 0 H2-staging pass through 3 0 0 0 H2-microtomy pass through TNTCc 0 0 0 H2 Microscope 1 NA NA 0 0 H2 Microscope 2 NA NA 0 0 H2-Table NA NA 0 0 OREXd- microtomy pass through 0 0 6 0 OREX – Anteroom pass through 0 0 0 0 OREX – Floor 1 2 0 0 OREX Witness Foil Table 3 0 1 0 Staging-Floor 16 0 15 0 Microtomy-Floor 3 0 2 0 a: CFU = Colony Forming Unit b: H2 = Hayabusa2 Lab c: TNTC = too numerous to count d: OREX = OSIRIS-REx Lab References: 1. ISO 14644-1:2015 - Cleanrooms and associated controlled environments -- Part 1: Classification of air cleanliness by particle concentration. 37 (2015). 2. McCubbin, F. M. et al. Space Sci Rev 215, (2019). 3. Pincus, D. H. Encyclopedia of Rapid Microbiological Methods (2005). 4. The United States Pharmacopeial Convention. USP General Chapter <1116> 17, 784–794 (2013). 5. Sheraba, N. S., Yassin, A. S. & Amin, M. BMC Research Notes 3, 278 (2010). 6. Utescher, C. L. de A., Franzolin, M. R., Trabulsi, L. R. & Gambale, V. Brazilian Journal of Microbiology 38, 710–716 (2007).

A B Regberg↗

Models, In situ, and Remote sensing of Aerosols (MIRA): Formation of an International Working Group

There is a natural partitioning of scientific interest amongst three specialties of aerosol re- search: modeling, in situ measurements, and remote sensing. The broader aerosol community benefits when these groups interact, and this strengthens overall scientific impact on climate and air quality research and predictions. The new MIRA working group establishes a forum for identifying collaborations and improving discussions amongst specialties and across regional boundaries. One area of keen interest is uniting satellite and ground-based lidar groups with other aerosol disciplines. Elastic backscatter lidars depend upon a priori knowledge of aerosol properties to convert measured lidar profiles into aerosol extinction profiles. Acquiring additional insight on aerosol properties and transport is highly valuable to these lidar groups to improve the data quality and aid in their scientific interpretation. Another area of interest is to facilitate the incorporation of measurements into global aerosol models. Modelers need aerosol optical look-up tables that enable quick conversions of hydrated (and dry) polydisperse size distributions into aerosol optical properties (extinction, scattering, etc.), but many of the existing tables are based upon outdated measurements. Thus, MIRA is building the Tables of Aerosol Optics (TAO), which is a community collection of aerosol optical calculations. This expands on the historical efforts of Shettle and Fenn, d’Almeida, GADS, OPAC, etc., except that TAO seeks continual input from the community. Thus, as aerosol measurement and computational techniques advance, so does the TAO collective. Since TAO is a community collective, it is expected that users will optionally upload computations for aerosol type as well as computations for all of the traditional aerosol species (like amm sulfate, amm nitrate, organics, etc.). The near-term purpose of the MIRA working group is to: * Characterize regional aerosol lidar ratios to support improvements of aerosol extinction profiles and understanding of aerosol typing. * Create TAO -- a community cooperative of aerosol optical tables. * Facilitate international communications between aerosol measurement and modeling groups. * Encourage the use of regional knowledge to develop and improve remote sensing techniques for current and future backscatter lidars located in space. * Enable and foster communication between the scientists who run global aerosol models and scientists who analyze space-based lidar data. We will discuss how a collaborative aerosol working group will be organized on this topic. Send email to calipso_v5alr-join@lists.nasa.gov with the word `subscribe' in the subject line to join MIRA.

Gregory Schuster↗

Surface and Atmospheric Shortwave Radiative Fluxes From ISCCP Data and Fu-Liou Algorithm at Higher Spatial and Vertical Resolution

NASA/GEWEX Surface Radiation Budget (SRB) has provided surface and TOA shortwave and longwave radiative fluxes using International Satellite Cloud Climatology data as the primary input. Release 4.0 came out in 2019, with data from July 1983 through June 2017, and improved validation stats relative to Release 3.0 (Stackhouse et al., 2012). Release 4.0 used the newly reprocessed ISCCP H data set. The shortwave algorithm for versions 3 and 4 has been based on the Pinker and Laszlo (1992) algorithm, which relies on the satellite-measured shortwave radiance to produce a TOA albedo. This background TOA albedo is made utilizing the background clear-sky visible radiance (called clear-sky composite radiance in the ISCCP data) and applying narrowband-to-broadband angular distribution models. Using a climatological aerosol assumption, the surface albedo is estimated using radiative transfer based (i.e., Fu/Liou radiative transfer model; Fu and Liou, 1993) look-up tables. Using this surface albedo and an instantaneous TOA albedo, the look-up tables are used to adjust both the aerosol optical depth (for clear sky) and cloud optical depth (for cloudy sky) for each scene. These properties and look up tables are then used to generate surface fluxes. While this has worked well to provide useful fluxes, it has occasionally resulted in inaccurate direct and diffuse surface SW fluxes due to the overreliance on aerosol optical depth. With increased computational power and storage now available, a more direct approach is now possible. Here we present a different approach for a future high resolution SRB Release 5.0. We replace the Pinker-Laszlo lookup table approach with a forward call to the Fu-Liou radiative transfer model as modified by the CERES team (Rose et al., 2006). In addition to being a proven radiation code, Fu-Liou allows the calculation of fluxes at different atmospheric levels and spectral bands, which will provide more insight into the surface radiation budget, its variability and attribution. It is expected that horizontal resolution will increase to at least 0.5°x0.5° from the current 1°x1°. Here we demonstrate a preliminary look at the next SRB, and show comparisons with the current release.

Earth Radiation Budget↗

Converter/Compressor Building Solid Waste Management Unit (SWMU) #89 Monitoring Well 21 Area Interim Measure Work Plan

This Work Plan details the approach and design for the Interim Measure (IM) to remediate groundwater within the MW21 Area where VOC concentrations exceed Florida Department of Environmental Protection Natural Attenuation Default Concentrations. The IM includes in-situ bioremediation via injection of emulsified vegetable oil (EVO) and emulsified zero-valent iron (EZVI). The in-situ bioremediation technology consists of injecting an electron donor substrate into the subsurface to promote microbial breakdown of VOCs. The EVO injections for this IM are designed based on the use of Provectus ERD-CH4, which is a vegetable oil/carbon substrate mixture. The EZVI injections for this IM are designed based on the use of Provectus EZVI-CH4. The IM treatment layout consists of nine injection locations of EVO at approximately 10-foot radius of influence (ROI) and three injections locations of EZVI at approximately 6-foot ROI. The injection method will be direct push using a DPT rig. The overall injection depths range from 7 to 17 ft bls. The 7 ft bls top depth is designed to be 2 ft below the water table to prevent substrates from reaching the top of the water table. Injections are planned to be implemented using 2 ft intervals and will take place using a bottom-up approach to 2 ft below the water table. This work plan further describes the IM design, injection calculations, performance monitoring plan, and provides an injection layout. Revision 1 of this Work Plan includes quarterly performance sampling during Year 1 in accordance with F.A.C. 62-780. These changes are reflected in Section 7 and Table 2 of the Work Plan.

Mark J Jonnet↗

Forecast of Standard Atomic Weights for the Mononuclidic Elements – 2011

In this short report, I will provide an early warning about potential changes to the standard atomic weight values for the twenty mononuclidic and the so-called pseudo-mononuclidic ({sup 232}Th and {sup 231}Pa) chemical elements due to the estimated changes in the mass values to be published in the next Atomic Mass Tables within the next two years. There have been many new measurements of atomic masses, since the last published Atomic Mass Table. The Atomic Mass Data Center has released an unpublished version of the present status of the atomic mass values as a private communication. We can not update the Standard Atomic Weight Table at this time based on these unpublished values but we can anticipate how many changes are probably going to be expected in the next few years on the basis of the forthcoming publication of the Atomic Mass Table. I will briefly discuss the procedures that the Atomic Weights Commission used in deriving the recommended Standard Atomic Weight values and their uncertainties from the atomic mass values. I will also discuss some concern raised about a proposed change in the definition of the mole. The definition of the mole is now connected directly to the mass of a {sup 12}C isotope (which is defined as 12 exactly) and to the kilogram. A change in the definition of the mole will probably impact the mass of {sup 12}C.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Method and apparatus for determining a normal combustion characteristic for an internal combustion engine from an accelerometer signal

The method comprises operating a calibration engine, and collecting combustion characteristic data and reference accelerometer signals, which are correlated with each other and stored in a calibration table. The calibration table can be used by an engine to determine a real-time normal combustion characteristic when the engine is operating by collecting a real-time accelerometer sensor signal and cross correlating with the correlated data stored in the calibration table. Accordingly, the apparatus comprises a calibration engine comprising a calibration sensor, a reference accelerometer sensor and a data storage device for storing the collected calibration data that is correlated with the collected reference accelerometer signals, and an engine equipped with an accelerometer sensor, a calibration table and an electronic engine controller programmed to receive real-time accelerometer signals and cross correlate them with reference accelerometer signals to determine a real-time normal combustion characteristic.

Huang, Jian↗

Method and apparatus for fast context cloning in a data processing system

A data processing system includes a memory system, a first processing element, a first address translator that maps virtual addresses to system addresses, a second address translator that maps system address to physical addresses, and a task management unit. A first program task uses a first virtual memory space that is mapped to a first system address range using a first table. The context of the first program task includes an address of the first table and is cloned by creating a second table indicative of a mapping from a second virtual address space to a second range of system addresses, where the second range is mapped to the same physical addresses as the first range until a write occurs, at which time memory is allocated and the mapping of the second range is updated. The cloned context includes an address of the second table.

Beard, Jonathan Curtis↗

Optimizing branch re-wiring in a software instruction cache

A method includes a computer device receiving a branch instruction; the computer device managing two tables, where a first table relates to application blocks and a second table relates to available address slots; and the computer device calculating a target of the branch instruction using a branch-to-link register, the computer device optimizes re-wiring in a cache using the calculation and the managed two tables.

97 MATHEMATICS AND COMPUTING↗

Address-based filtering for load/store speculation

Address-based filtering for load/store speculation includes maintaining a filtering table including table entries associated with ranges of addresses; in response to receiving an ordering check triggering transaction, querying the filtering table using a target address of the ordering check triggering transaction to determine if an instruction dependent upon the ordering check triggering transaction has previously been generated a physical address; and in response to determining that the filtering table lacks an indication that the instruction dependent upon the ordering check triggering transaction has previously been generated a physical address, bypassing a lookup operation in an ordering violation memory structure to determine whether the instruction dependent upon the ordering check triggering transaction is currently in-flight.

Kalamatianos, John↗