Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vapor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,369 records · Page 76
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Incorporating corrosion design constraints in desalination process optimization: A case study in mechanical vapor compression

Corrosion is an expensive and complex challenge for desalination, yet current design approaches do not explicitly account for corrosion mechanisms in process modeling and technoeconomic analysis. Here, to address this gap, we present a workflow for incorporating corrosion design constraints directly into desalination process optimization models. We develop surrogate models for general and localized corrosion metrics as functions of temperature, pH, salinity, dissolved oxygen, and material using data from OLI Systems’ Corrosion Analyzer. We then integrate these surrogates as corrosion design constraints in a cost-optimization MVC model that minimizes the levelized cost of water (LCOW). For a case study of mechanical vapor compression (MVC) treating seawater across a range of recoveries, we find dissolved oxygen (DO) is the dominant driver of localized corrosion, and thus of cost-optimal material choice and operating conditions. Reducing the DO from 8 mg/L to 0.5 mg/L reduces the LCOW by 15-35%, informing the breakeven costs for implementing DO removal or selecting highly corrosion-resistant alloys. This framework is broadly applicable across corrosion types, materials, and components and enables desalination process design that minimizes capital costs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Advanced defrosting techniques in air source heat pumps: A review of vapor injection, thermal energy storage, and experimental frost accumulation data

Electrification is a critical step for reducing greenhouse gas emissions from heating. Air source heat pumps (ASHPs) are a promising alternative to fossil fuel-based systems due to their high coefficients of performance (COP), dual heating and cooling capability, and lower carbon footprint. However, for ASHPs to achieve widespread adoption, they must operate reliably across all climates, including cold regions. Additionally, defrosting techniques should be energy efficient and minimally disruptive to indoor comfort. Vapor injection (VI) technology can address the high-pressure and high-temperature lift challenges encountered in low ambient conditions. More recently, in addition to enhancing heating performance, VI has also been shown to improve the speed and efficiency of reverse cycle defrosting. Likewise, thermal energy storage (TES) has steadily gained attention for its ability to serve as an auxiliary heat source during both normal operation and defrosting. This review analyzes the benefits and limitations of VI- and TES-assisted defrosting approaches. While both technologies show strong potential individually, no studies to date have explored their combined use in ASHP systems. Additionally, to support continued development of defrosting strategies, both in modeling and experimental work, it is critical to establish frost accumulation data under a range of operating conditions. By compiling the available data from the literature, this paper also highlights the limited availability of such experimental data and the wide variation in frosting and defrosting durations and termination criteria, which are often influenced by system design and test setups.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Vapor liquid equilibrium of pure and aqueous Methyl diethanolamine (MDEA), 2-Dimethylmonoethanolamine (DMMEA), N-Methylmonoethanolamine (MMEA) and 1-(2-Aminoethyl)piperazine (AEP): Experimental results and modeling

This work presents new vapor-liquid data for the pure components 2-dimethylmonoethanolamine (DMMEA) and N-methylethanolamine (MMEA) and for the binary systems of aqueous methyldiethanolamine (MDEA), DMMEA, MMEA, and 1-(2-aminoethyl)piperazine (AEP). New Antoine models are developed for the pure component systems, and new and improved NRTL models for the binary systems. In the model development, together with new data from this work, all available data on VLE, excess heat of mixing, H E , freezing point depression, and specific heat were gathered, evaluated and used selectively for parameter optimization. Emphasis has been put on a best possible representation of amine volatility to enable reasonable predictions of amine emissions from absorption plants and to form a basis for subsequent models of ternary systems with CO 2 . In conclusion, model predictions are compared with experimental results and other models, source by source, and the overall results are satisfactory.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Modeling and experimental validation of a W f /W-fabrication by chemical vapor deposition and infiltration

Tungsten (W) has a unique combination of excellent thermal properties, low sputter yield, low hydrogen retention, and acceptable activation. Therefore, W is presently the main candidate for the first wall material in future fusion devices. However, its intrinsic brittleness and its further embrittlement during operation bears the risk of a sudden and catastrophic component failure. As a countermeasure, tungsten fiber-reinforced tungsten (W f /W) with extrinsic toughening is being developed. A possible synthesis route is chemical vapor deposition (CVD) using heated W fabrics as substrate. The challenge is that the growing CVD-W can isolate domains from precursor access leading to strength-reducing pores. To deepen the process understanding and to optimize the CVD parameters, models were developed with COMSOL Multiphysics and validated experimentally. W deposition rate equations as function of the temperature and the partial pressures of the precursors H 2 and WF 6 were experimentally validated in previous work. In the present article, these equations are applied to obtain partial pressures within the CVD reactor. The results are taken as input for transient simulations in the microscale, in which W coatings, growing onto multiple adjacent W fibers, were simulated via mesh deformation and remeshing. The surface-to-surface contact of the W coatings and the corresponding potential pore formation were simulated by implementing sophisticated deposition rate stop conditions. Within the measuring uncertainties of ≃ ±1%, the models are validated successfully by experimental comparison regarding the deposition rate, pore structure, and relative densities ranging from 0.6 to 0.9.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Thermoluminescence and optically stimulated luminescence response of Al 2 O 3 coatings deposited by mist-chemical vapor deposition

Aluminum oxide (Al 2 O 3 ) is a widely used ceramic material which can be applied as a protective coating on metallic structures to improve corrosion resistance and mechanical properties. Al 2 O 3 also has great potential as a functional thin film device in optoelectronics. When it is doped with carbon (Al 2 O 3 :C), this material system can serve as a reliable radiation dosimeter. The combination of optoelectronic, dosimetric, and protective properties demonstrated by Al 2 O 3 uniquely positions it for dual use applications in nuclear forensics, nonproliferation and safeguards, emergency response, retrospective dosimetry, and nondestructive inspection. Here, in this study, an innovative ultrasonic mist-chemical vapor deposition (Mist-CVD) system was used to deposit thin (nm level) Al 2 O 3 coatings on 304 stainless steel substrates. The single aliquot regeneration (SAR) and additive dose reconstruction techniques were then used to investigate the thermoluminescence (TL) and optically stimulated luminescence (OSL) response of the coated substrates to increasing doses of β irradiation. This study demonstrates that nm-thick Al 2 O 3 coatings hold promise as novel nano-dosimeters which could be leveraged for a series of applications such as nonproliferation and safeguards, retrospective dosimetry, and nondestructive inspection.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Energy and exergy analysis of multi-stage vacuum membrane distillation integrated with mechanical vapor compression

Membrane distillation (MD) is a promising candidate for desalinating hypersaline brine, but its poor energy efficiency has remained a major barrier for widespread application. One possible solution to this issue is to recover the latent heat in the process. In this work, a multi-stage vacuum MD (MSVMD) was integrated with a mechanical vapor compressor (MVC) to enhance the latent heat recovery, and the energetic and exergetic performance of this integrated process was examined. A comprehensive energy and exergy analysis is provided to compare MSVMD and MSVMD-MVC processes for desalination of hypersaline brine. This analysis was conducted by examining the effect of the compression ratio on the energetic and exergetic performance, and the findings are reported in terms of specific thermal energy consumption (STEC), specific electricity consumption (SEC), and exergetic efficiency. The energy analysis shows that thermal energy consumption can be reduced as the compression ratio increases, due to the enhancement of latent heat recovery. The MSVMD-MVC process can be operated in a steady-state condition, without the need for thermal heat input; with STEC and SEC of 0 and 49 kWh/m 3 at the feed temperature of 50 °C and MVC compression ratio of 2.14. Moreover, exergy analysis demonstrates the efficacy of the eNRTL model in exergy calculation. Exergy destruction can be greatly reduced by increasing the compression ratio to an optimal value. For high salinity brine (124 g/L), MSVMD-MVC achieved a higher exergetic efficiency of 6.85%, compared to 2.42% in MSVMD. Furthermore, the result suggests that the application of MVC can intensify the energy efficiency and exergetic efficiency of the MSVMD system, although this process cannot outperform the current desalination technologies from the standard primary energy point of view.

42 ENGINEERING↗
DOE OSTI2021

Silicon Dioxide Deposited Using Atmospheric Pressure Plasma Chemical Vapor Deposition for Improved Adhesion and Water Intrusion Resistance for Lightweight Manufacturing

This work aims to demonstrate the barrier coating, and adhesion promoting properties of silica-based coatings deposited using an atmospheric pressure plasma torch (APPT). This is achieved by applying an industrial grade adhesive to silica thin films deposited, on the surfaces to be joined, using atmospheric pressure plasma chemical vapor deposition (APP-CVD), to make single joint lap shear samples of different metal combinations commonly found in lightweight manufacturing such as aluminum and magnesium as well as steel. To deposit these thin films, two separate silicon based organic precursors, hexamethyldisiloxane (HMDSO), and tetraehylorthosilicate (TEOS), are used. Here, samples are bonded using DuPont Betamate 1486 adhesive, and the lap shear results for these films are compared to the lap shear results of a chemically cleaned control using the same adhesive. The APPT uses a microwave power supply and gas mixtures of N 2 and Ar. The adhesion of the films are tested using lap shear, and elevated temperature water soaks are conducted on the joints as well to simulate environmental exposure. Lap shear results from samples with silica thin films max shear stress are 25%-115% increase compared to control samples depending on material. After exposure to water soak the max shear strength of the joints decreased by less than 15%, which demonstrates the films capabilities as a water barrier. Film morphology is examined using Scanning Electron Microscopy (SEM), and the film’s composition and approximate thickness are obtained using Rutherford Backscattering Spectroscopy (RBS).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hollow-cathode chemical vapor deposition of thick, low-stress diamond-like carbon films

A radio-frequency (RF), hollow-cathode plasma source with confining magnetic field is described for the chemical vapor deposition of thick ( > 10 µm), amorphous diamond-like carbon ablator films for inertial confinement fusion applications. Plasma is characterized by optical emission spectroscopy, while properties of the resultant films are measured by a combination of profilometry, Rutherford backscattering spectrometry, elastic recoil detection analysis, X-ray diffraction, Raman spectroscopy, and atomic force microscopy. The dependence of the deposition rate, film density, elemental composition, self-bias and residual stress is reported as a function of RF power. Higher density films were found when using Ar plasma, than N 2 or H 2 plasma. The coatings produced are x-ray amorphous, exhibit low compressive stress ( ~ 100 MPa), high density ( < 1.7 g/cm 3 ), hydrogen content of ~ 30 at.%, and a low average roughness of 0.75 nm. Finally, applications of these films as tunable-density ablators for inertial confinement fusion experiments are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Component innovations for lower cost mechanical vapor compression

Despite significant capital and operating costs, mechanical vapor compression (MVC) remains the preferred technology for challenging brine concentration applications. Here, this work seeks to assess the dependence of MVC costs on feedwater salinity and desired water recovery and to quantify the value of improved component performance or reduced component costs for reducing the levelized cost of water (LCOW) of MVC. We built a cost optimization model coupling thermophysical, heat and mass transfer, and technoeconomic models to optimize and identify low cost MVC system designs as a function of feedwater salinity and water recovery. The LCOW ranges over 3.6 to 6.1 $\$$/m 3 for seawater feed salinities of 25–150 g/kg and water recoveries of 40–80 %. We then perform sensitivity analysis on parameter inputs to isolate irreducible costs and determine high value component innovation targets. The LCOW was most sensitive to evaporator material costs and performance, including the overall heat transfer coefficient in the evaporator. Process and material innovations such as polymer-composite evaporator tubes that reduce evaporator costs by 25 % without reducing heat transfer performance by more than 10 % would result in MVC cost reductions of 8 %.

42 ENGINEERING↗
DOE OSTI2023

Design of Planarizing Growth Conditions on Unpolished and Faceted (100)-Oriented GaAs Substrates Using Hydride Vapor Phase Epitaxy

Here we performed a design of experiments (DoE) analysis to determine the effect of various growth parameters on in situ planarizing overgrowth of rough substrates using hydride vapor phase epitaxy (HVPE). We used two types of rough (100)-oriented GaAs substrates to compare the effect of the initial morphology on the epitaxial growth behavior: an irregular, as-cut surface resultant from cutting the wafer from a GaAs boule and a regularly faceted surface produced by controlled spalling. The DoE analysis identified trends in the overgrowth behavior with changing growth conditions, and we used these trends to design favorable planarization growth conditions for each surface type. These favorable conditions enabled full planarization of a spalled surface with >2.5 um facet height within 10.8 min of growth. The root mean squared (RMS) surface roughness of the resulting (100) surface was 24.5 nm over a 286 um x 215 um area. Our results show that planarization growth by HVPE is a promising technique to enable device growth directly on rough substrates, and the trends revealed through DoE analysis indicate a path toward further optimization of planarization growth conditions for as-cut and spalled surfaces.

14 SOLAR ENERGY↗
DOE OSTI2025

Halide Vapor Phase Epitaxy of Ge from an Elemental Source

Halide vapor phase epitaxy shows promise for low-cost photovoltaic device manufacturing because of its high growth rates and lower cost elemental precursors but previously has not been used to deposit epitaxial Ge. Here, we demonstrate Ge deposition by generating GeCl 2 in situ from solid Ge and HCl in a N 2 ambient. To achieve Ge growth, we inject AsH 3 and PH 3 as sources of active hydrogen to the growth surface to create a driving force for growth. We do not observe Ge growth unless a supply of hydrogen is added, consistent with thermodynamic calculations. Furthermore, we show the hydrogen source must crack readily on the substrate surface to enable growth; relatively stable sources such as H 2 do not cause growth. Unintentional group V doping is one drawback of using AsH 3 and PH 3 to drive the Ge reaction. We observed As or P concentrations in the Ge films ranging from 4 x 10 17 to 1 x 10 18 atoms/cm 3 , concentrations that can drastically influence device characteristics. However, we note there are numerous other "helper molecule" options that can provide active hydrogen without doping or etching the material. This work provides a path forward for Ge deposition for optoelectronic devices from an elemental source.

14 SOLAR ENERGY↗
DOE OSTI2021

Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons

Chemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming ultralong ribbon-like structures with the length to the width aspect ratio of up to 500. Computational modeling of the growth mechanism of a BP flake is also presented in support of the observed columnar growth. Calculation of the average energy of the molecule in the asymmetric flakes shows that the growth of the structure in the zigzag direction is more energetically favorable than in the armchair direction.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Engineering Self-Assembled Domain Asymmetry in Solvent Vapor Annealed Block Copolymer–Homopolymer Blend Films

Thin-film block copolymer (BCP) self-assembly is a powerful approach to generate highly uniform nanopatterns across large areas, yet the symmetries of these nanopatterns are constrained by the relative volume occupied by each polymer block. Here, we present a conceptually new approach to circumvent this limitation by combining homopolymer (HP) blending with solvent vapor annealing (SVA), demonstrated here for ternary blends of a near-symmetric BCP with athermal, low molar mass HPs. Screening of BCP–HP interactions by a weakly selective solvent promotes entropically driven delocalization of HP throughout both blocks and enables assembly of metastable lamellae for volume fractions as high as 0.78. Subsequent brief thermal annealing induces HPs to withdraw to their enthalpically favored domains, sharpening domain interfaces on a time scale much shorter than pattern coarsening. This renders lamellar nanopatterns with tunable widths that can be transferred to other materials with high fidelity. Furthermore, the persistence of the metastable asymmetric lamellae upon thermal annealing is sensitive to film confinement, as they are preserved in submonolayer films but transition to horizontal cylinders in films more than one monolayer thick. SVA using a strongly selective solvent results in assembled morphologies aligned closely with expectations based on the total polymer blend composition, underscoring the key role of BCP–HP interactions in dictating domain asymmetry. Overall, this work details important principles for using SVA to mediate BCP–HP interactions in thin films, thereby presenting opportunities to engineer pathways for the assembly of well-ordered nanopatterns with designer feature asymmetry for lithographic or nanotexturing applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Phase-Selective Synthesis of Rhombohedral WS 2 Multilayers by Confined-Space Hybrid Metal–Organic Chemical Vapor Deposition

Rhombohedral polytype transition metal dichalcogenide (TMDC) multilayers exhibit non-centrosymmetric interlayer stacking, which yields intriguing properties such as ferroelectricity, a large second-order susceptibility coefficient χ (2) , giant valley coherence, and a bulk photovoltaic effect. These properties have spurred significant interest in developing phase-selective growth methods for multilayer rhombohedral TMDC films. Here, in this study, we report a confined-space, hybrid metal–organic chemical vapor deposition method that preferentially grows 3R-WS 2 multilayer films with thickness up to 130 nm. We confirm the 3R stacking structure via polarization-resolved second-harmonic generation characterization and the 3-fold symmetry revealed by anisotropic H 2 O 2 etching. The multilayer 3R WS 2 shows a dendritic morphology, which is indicative of diffusion-limited growth. Multilayer regions with large, stepped terraces enable layer-resolved evaluation of the optical properties of 3R-WS 2 via Raman, photoluminescence, and differential reflectance spectroscopy. These measurements confirm the interfacial quality and suggest ferroelectric modification of the exciton energies.

3R-WS2↗
DOE OSTI2025

Overcoming the Conductance versus Crossover Trade-off in State-of-the-Art Proton Exchange Fuel-Cell Membranes by Incorporating Atomically Thin Chemical Vapor Deposition Graphene

Permeance–selectivity trade-offs are inherent to polymeric membranes. In fuel cells, thinner proton exchange membranes (PEMs) could enable higher proton conductance and increased power density with lower area-specific resistance (ASR), smaller ohmic losses, and lower ionomer cost. However, reducing thickness is accompanied by an increase in undesired species crossover harming performance and long-term efficiency. Here, we show that incorporating atomically thin monolayer graphene synthesized via scalable chemical vapor deposition (CVD) and tunable defect density into PEMs (Nafion, ~5–25 μm thick) can allow for reduced H 2 crossover (~34–78% of Nafion of a similar thickness) while maintaining adequate areal proton conductance for applications (>4 S cm –2 ). In contrast to most prior work using >50 μm symmetric Nafion sandwich structures, we elucidate the interplay of graphene defect density and Nafion proton transport resistance on the performance of Nafion|graphene composite membranes and find high-quality low-defect density CVD graphene (G) supported on Nafion 211 (~25 μm); i.e., N211|G has a high areal proton conductance (~6.1 S cm –2 ) and the lowest H 2 crossover (~0.7 mA cm –2 ). Fully functional centimeter-scale N211|G fuel-cell membranes demonstrate performance comparable to that of state-of-the-art Nafion N211 at room temperature as well as standard operating conditions (~80 °C, ~150–250 kPa-abs) with H 2 /air (power density ~0.57–0.63 W cm –2 ) and H 2 /O 2 feed (power density ~1.4–1.62 W cm –2 ) and markedly reduced H 2 crossover (~53–57%).

25 ENERGY STORAGE↗
DOE OSTI2022

Temperature-Dependent Phase Stable Hybrid Halide Perovskite Films by Chemical Vapor Deposition

Methylammonium lead iodide (MAPbI 3-x Cl x ) thin films were synthesized using chemical vapor deposition. Temperature-dependent grazing incidence synchrotron-based X-ray diffraction measurements confirm that the structure of MAP-bI 3-x Cl x , where Cl acts more like a dopant, remains throughout in the tetragonal phase in the temperature range of 20-300 K. Here these studies are further correlated with temperature-dependent photo-luminescence (PL) studies. The PL peak energy monotonically increases with temperature, suggestive of a single-phase behavior. Resistance measurements conducted as a function of temperature show an absence of inflection points, suggesting uniformity in its phase. Between 200 and 325 K, the resistance remains a constant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Catalysis of the Oxygen-Evolution Reaction in 1.0 M Sulfuric Acid by Manganese Antimonate Films Synthesized via Chemical Vapor Deposition

Manganese antimonate (Mn y Sb 1–y O x ) electrocatalysts for the oxygen-evolution reaction (OER) were synthesized via chemical vapor deposition. Mn-rich rutile Mn 0.63 Sb 0.37 O x catalysts on fluorine-doped tin oxide (FTO) supports drove the OER for 168 h (7 days) at 10 mA cm –2 with a time-averaged overpotential of 687 ± 9 mV and with >97% Faradaic efficiency. Time-dependent anolyte composition analysis revealed the steady dissolution of Mn and Sb. Extended durability analysis confirmed that Mn-rich Mn y Sb 1–y O x materials are more active but dissolve at a faster rate than previously reported Sb-rich Mn y Sb 1–y O x alloys.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Growth of AlGaAs, AlInP, and AlGaInP by Hydride Vapor Phase Epitaxy

In this work, we demonstrate hydride vapor phase epitaxy (HVPE) of Al x Ga 1-x As, Al x In 1-x P, and Al x Ga y In 1-x-y P using an AlCl 3 precursor. We study the growth of the Al x Ga 1-x As alloy system to elucidate the effects of deposition temperature, V/III ratio, and group V precursor species on Al solid incorporation via AlCl 3 . Crucially, the presence of group V hydride at the growth front kinetically promotes the solid incorporation of Al. We use these insights to demonstrate controlled deposition of Al x Ga 1-x As, and for the first time by HVPE, Al x In 1-x P and Al x Ga y In 1-x-y P. Finally, these results create exciting implications for HVPE-grown high-efficiency III-V solar cells and devices with reduced cost.

14 SOLAR ENERGY↗