Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “writing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Predicting multi-nodal in-nozzle particle interactions in high-viscosity fluid mediums for acoustophoretic direct-ink writing of line-patterned composites

Patterned functional materials offer improved properties (electrical, thermal, etc.) over their bulk counterparts in many applications, including energy storage, flexible electronics, and sensors. However, manufacturing approaches for patterning materials over large areas with features on the order of hundreds of microns or less are limited. Acoustophoresis, which uses acoustic forces to control particle arrangement in a fluid medium, is a pathway to address this challenge. This process is dependent on particle and fluid properties and enables patterning of a broad range of materials. Herein, a model with experimental validation is presented to demonstrate that acoustophoresis can be combined with direct-ink writing (DIW) to fabricate line patterns over large cm-scale areas. An in-nozzle particle interaction model was developed to investigate the impact of processing conditions on multi-nodal acoustophoretic DIW. The model predicts patterned line widths within a factor of two relative to experimental results for a high viscosity case study. Here, the model was used to investigate the impact of frequency, particle loading, particle radius, and acoustic pressure on line width and patterning time, providing critical feedback regarding the processing conditions suitable for a target application. Model results illustrate that frequency has the greatest impact on line patterns: increasing from 1 to 3 MHz resulted in a greater than 65% reduction in line width and a greater than 85% reduction in patterning time. Additionally, experiments were conducted with an alumina-epoxy ink and a ~21 cm 2 area pattern was rastered in ~5.5 minutes, demonstrating a path towards large-area line-patterned composite fabrication.

25 ENERGY STORAGE↗
DOE OSTI2026

Towards gradient multimaterial toolpath generation for direct ink writing with connected fermat spirals

This work describes advances towards a reproducible, parametrically defined algorithm for generating graded multimaterial toolpaths for direct ink writing. Expanding on the existing Fermat space-filling algorithm and coupling with image-driven processing techniques, we demonstrate the fabrication of multimaterial structures. Here, material composition is encoded within toolpaths by parsing hue values from a multi-colored image. By performing dynamic velocity compensation based on local curvature and Euclidean distance filtering, internal voids are mitigated while optimizing print fidelity. Here, the work opens new avenues for designing complex toolpaths with locally programmable composition.

3D Printing↗
DOE OSTI2022

Additive manufacturing of nanotube-loaded thermosets via direct ink writing and radio-frequency heating and curing

Direct Ink Writing (DIW) is an extrusion-based additive manufacturing method where the print medium is a liquid-phase ‘ink’ dispensed out of nozzles and deposited along digitally defined paths. Conventional DIW of thermosetting resins relies on viscosity modifying agents, novel crosslinking chemistries, and/or long curing schedules in an oven. Here we demonstrate the use of a co-planar radio frequency applicator to generate an electric field, which can be used to rapidly heat and cure nano-filled composite resins as they are printed. This method avoids the need for an oven or post- curing step. This process consists of a sequential print-and-cure cycle which allows for printing of high-resolution, multi-layered structures. Every extruded layer is partially cured using RF before depositing the next layer; this allows the printed part to maintain structural integrity. The process enables both increased throughput and decreased touch time relative to traditional manufacturing. Commercial epoxy resin with varied nano-filler loadings were examined as DIW candidates. After printing, the thermo-mechanical properties, surface finish, and shape retention of RF-cured samples were comparable to conventionally cured samples. Furthermore, this method of manufacturing establishes RF heating as a suitable alternative to conventional methods, facilitating rapid, free-form processing of thermosetting resins without a mold.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct ink writing of boron carbide monoliths

Direct ink writing – an extrusion-based additive manufacturing process – followed by pressureless sintering was investigated to produce boron carbide monoliths. The effects of ceramic powder loading and Pluronic binder concentration on the rheology of boron carbide pastes were studied and linked to both processing behaviour and final outcome in terms of sintered density and hardness. The effects of printing parameters, in particular orifice diameter and printing speed, were also investigated. Reducing the size of the extrusion nozzle from 584 μm to 406 μm led to significantly better shape retention, lower surface roughness, as well as higher density and hardness. A 203 μm printing orifice was also trialled but was unsuccessful due to faster drying kinetics that occurred with smaller ceramic struts resulting in rapid warping and nozzle clogging. Carbon-black – 8 wt% relative to B 4 C – acted as an effective sintering aid to increase both density and hardness. After optimisation of feedstock and printing parameters, few-layer samples (3–5 layers) had a density as high as ~ 97 % TD and a hardness of ~ 30 GPa. On the other hand, 18-layer specimens had a sintered density of ~ 87 % TD, despite a fully dense microstructure, due to the formation of a 3D array of inter-strut pores. Nevertheless, several issues that arose during manufacturing and post-processing were detrimental to the density and structural integrity of printed specimens; these issues were identified, discussed, and suggestions for future work are provided in this report.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct ink writing of aqueous-based Gadolinium (III) oxide slurries

Gadolinium (III) oxide (gadolinia, Gd 2 O 3 ) has recently been identified as an intriguing material for applications in the medical, solid oxide fuel cell, and nuclear industries. This interest drives the need for developing and understanding manufacturing techniques that can produce dense Gd 2 O 3 structures. Direct ink writing (DIW), an extrusion-based additive manufacturing method, has also garnered interest because of its capability to produce dense ceramic parts with increased complexity in an economical manner. In this study, DIW was explored as a manufacturing technique for Gd 2 O 3 . Experiments were performed to develop Gd 2 O 3 bearing inks capable of being processed via DIW. Ink solids loading and sintering temperatures were varied to assess their impact on the final density and microstructure. Optimum sintering conditions are proposed and were experimentally verified at a dwell temperature of 1500°C. Gd 2 O 3 samples were successfully manufactured using DIW, achieving densities greater than 96 % of the theoretical density.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct ink writing of shear exfoliated two-dimensional nanomaterial- elastomeric multifunctional nanocomposite

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman analysis. Incorporating exfoliated graphene (40 wt%) increased viscosity by ∼6 orders of magnitude due to enhanced particle–matrix interactions, leading to pronounced yield stress behavior and a yield stress of approximately 1598 Pa, which enabled excellent shape retention during extrusion. Using the DIW technique, porous structures such as desalination membranes, self-sensing bone scaffolds, thermal management coating, and serpentine strain sensors were fabricated. When tested in a direct contact membrane distillation setup, the fabricated membrane demonstrated a promising permeate flux of 21.85 Lm −2 h −1 and a salt rejection of 74.3 %. The fabricated serpentine sensor exhibited stable signal variations under cyclic tensile loading, with a working range of 0–200 % strain and a maximum gauge factor of 43,735. A cell culture test using the printed bone scaffold demonstrated promising cell attachment and proliferation. The DIW printed hBN nanocomposite exhibited reversible shape change under heat, demonstrating potential 4D printing capability and efficient thermal management when exposed to high heat or flame.

Desalination↗
DOE OSTI2020

Three-dimensional hierarchical nanoporous copper via direct ink writing and dealloying

Three-dimensional (3D) hierarchical nanoporous Cu (3DHNP-Cu) is synthesized using a combination of direct ink writing (DIW) based 3D printing, thermal sintering, and chemical dealloying of Mn–Cu alloys. Through tuning processing conditions such as ink composition and cooling rate (after sintering), with consideration of Mn loss during sintering, 3DHNP-Cu with fully bicontinuous nanostructures and negligible residual Mn can be produced after dealloying. The 3DHNP-Cu is comprised of structural features that span seven orders of magnitude, where DIW digitally controls macroscale porous features, thermal sintering and degradation of the binding polymer determines microscale porous features, and dealloying gives rise to nanoscale pores.

36 MATERIALS SCIENCE↗
DOE OSTI2023

One-Component, Vinyl-Functional Fluorosilicone Pastes for Direct Ink Write Additive Manufacturing

In this study, one-component (“all-in-one”) fluorosilicone pastes specifically designed for application in direct ink write (DIW) additive manufacturing (AM) have been developed. They consist of vinyl-functional, methyltrifluoropropyl-containing (MeTfpS) terpolysiloxane base polymer(s), hydrosilyl-functional cross-linker(s), UV-sensitive hydrosilylation catalyst, thixotropic additive, and trimethylsilylated fumed silica filler, with other additives that are optional. Their base polymers were completely amorphous and linear, with molecular weights (M n ) ranging from approximately 7000 to 50,000 and specifically targeted for the viscosity range ideal for DIW. These polymers were prepared by anionic ring-opening polymerizations (A-ROP) of appropriate mixtures of cyclic siloxanes initiated by oligomeric, difunctional tetramethylammonium silanolate in the presence of a difunctional tetramethyldivinyldisiloxane end-blocker and molecular weight regulator. Two series of these terpolymers were prepared: one containing 5 mol % MeTfpS repeat units but varying degrees of polymerization (DP) from 80 to 600 and the other containing 5, 10, and 15 mol % MeTfpS at a constant DP of 600. All polymers contained mostly random distributions of MeTfpS repeat units. The pastes were prepared by speed-mixing, ready for use in DIW, they exhibited ideal thixotropy, long-term (over a year) rheological stability, and can be quickly (within seconds) and permanently cured by room-temperature, UV-activated hydrosilylation in air. The resulting elastomers showed base polymer molecular weight- and composition-dependent stress-induced crystallization (SIC) at higher molecular weights and lower trifluoropropyl contents and tunable Shore A hardness (30A–40A) typical for soft polysiloxane rubbers. Preliminary DIW tests indicated excellent printability with high precision of printed shapes and clearly present these one-component pastes as prime candidates for simple and practical printing of silicone elastomer objects.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sub-100 mA/cm 2 CO 2 -to-CO Reduction Current Densities in Hierarchical Porous Gold Electrocatalysts Made by Direct Ink Writing and Dealloying

While most research efforts on CO 2 -to-CO reduction electrocatalysts focus on boosting their selectivity, the reduction rate, directly proportional to the reduction current density, is another critical parameter to be considered in practical applications. This is because mass transport associated with the diffusion of reactant/product species becomes a major concern at a high reduction rate. Nanostructured Au is a promising CO 2 -to-CO reduction electrocatalyst for its very high selectivity. However, the CO 2 -to-CO reduction current density commonly achieved in conventional nanostructured Au electrocatalysts is relatively low (in the range of 1–10 mA/cm 2 ) for practical applications. In this work, we combine direct ink writing-based additive manufacturing and dealloying to design a robust hierarchical porous Au electrocatalyst to improve the mass transport and achieve high CO 2 -to-CO reduction current densities on the order of 64.9 mA/cm 2 with CO partial current density of 33.8 mA/cm 2 at 0.55 V overpotential using an H-cell configuration. Although the current density achieved in our robust hierarchical porous Au electrocatalyst is one order of magnitude higher than the one achieved in conventional nanostructured electrocatalysts, we found that the selectivity of our system is relatively low, namely 52%, which suggests that mass transport remains a critical issue despite the hierarchical porous architecture. We further show that the bulk dimension of our electrocatalyst is a critical parameter governing the interplay between selectivity and reduction rate. In conclusion, the insights gained in this work shed new light on the design of electrocatalysts toward scale-up CO 2 reduction and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Single-Step Direct Laser Writing of Multimetal Oxygen Evolution Catalysts from Liquid Precursors

We investigate a laser direct-write method to synthesize and deposit metastable, mixed transition metal oxides and evaluate their performance as oxygen evolution reaction catalysts. This laser processing method enabled the rapid synthesis of diverse heterogeneous alloy and oxide catalysts directly from cost-effective solution precursors, including catalysts with a high density of nanocrystalline metal alloy inclusions within an amorphous oxide matrix. The nanoscale heterogenous structures of the synthesized catalysts were consistent with reactive force-field Monte Carlo calculations. By evaluating the impact of varying transition metal oxide composition ratios, we created a stable Fe 0.63 Co 0.19 Ni 0.18 O x /C catalyst with a Tafel slope of 38.23 mV dec -1 and overpotential of 247 mV, a performance similar to that of IrO 2 . Synthesized Fe 0.63 Co 0.19 Ni 0.18 O x /C and Fe 0.14 Co 0.46 Ni 0.40 O x /C catalysts were experimentally compared in terms of catalytic performance and structural characteristics to determine that higher iron content and a less crystalline structure in the secondary matrix decreases the charge transfer resistance and thus is beneficial for electrocatalytic activity. Furthermore, this conclusion is supported by density-functional theory calculations showing distorted active sites in ternary metal catalysts are key for lowering overpotentials for the oxygen evolution reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Direct-write 3D printing of NdFeB bonded magnets

We report a method to fabricate Nd-Fe-B bonded magnets of complex shape via extrusion-based additive manufacturing (AM), also known as 3D-printing. We have successfully formulated a 3D-printable epoxy-based ink for direct-write AM with anisotropic MQA NdFeB magnet particles that can be deposited at room temperature. The new feedstocks contain up to 40 vol.% MQA anisotropic Nd-Fe-B magnet particles, and they are shown to remain uniformly dispersed in the thermoset matrix throughout the deposition process. Ring, bar, and horseshoe-type 3D magnet structures were printed and cured in air at 100°C without degrading the magnetic properties. Lastly, this study provides a new pathway for fabricating Nd-Fe-B bonded magnets with complex geometry at low temperature, and presents new opportunities for fabricating multifunctional hybrid structures and devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fluid Mechanics Challenges in Direct-Ink-Writing Additive Manufacturing

Direct-ink writing (DIW) has rapidly become a versatile 3D fabrication method due to its ability to deposit a wide range of complex fluids into customizable 3D geometries. This review highlights key fundamental fluid mechanics and soft matter challenges across the different stages of the DIW printing process. The rheology of fluids and suspensions governs the flow behavior through narrow nozzles, posing questions about extrudability, confined flow dynamics, and clogging mechanisms. Downstream, the formation and deposition of extruded filaments involve extensional flows and potential instabilities, while postdeposition dynamics introduces complexities related to yield stress and structural stability. These stages are inherently interdependent, as optimizing material composition without considering filament stability risks compromising the final structure. As DIW applications expand through advanced ink formulations, developing fundamental fluid mechanics frameworks is essential to replace trial-and-error approaches with predictive design methodologies to enable more precise control and improved reliability of the printing process.

3D printing↗
DOE OSTI2021

Direct ink writing techniques for in situ gelation and solidification

Direct ink writing (DIW) is an extrusion-based 3D printing method which prints near ambient temperatures and has one of the broadest printable material selections among additive manufacturing techniques. However, DIW uses viscoelastic materials susceptible to collapse during printing. Overall, one promising route to improve the structural integrity of viscoelastic inks is using in situ curing methods to increase the yield strength of the printed structures after deposition. This review summarizes progress in three representative methods of in situ curing for DIW, including ultra-violet-induced crosslinking, rapid cure of reactive ingredients, and flash vaporization of a solution’s solvent to coagulate dissolved polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Towards a study protocol: A data-driven workflow to identify error sources in direct ink write mechatronics

Abstract Using Direct Ink Write (DIW) technology in a rapid and large-scale production requires reliable quality control for printed parts. Data streams generated during printing, such as print mechatronics, are massive and diverse which impedes extracting insights. In our study protocol approach, we developed a data-driven workflow to understand the behavior of sensor-measured X- and Y- axes positional errors with process parameters, such as print velocity and velocity control. We uncovered patterns showing that instantaneous changes in the velocity, when the build platform accelerates and decelerates, largely influence the positional errors, especially in the X- axis due to the hardware architecture. Since DIW systems share similar mechatronic inputs and outputs, our study protocol approach is broadly applicable and scalable across multiple systems. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Structure and Filler on Mechanical Properties of Direct Ink Write Pads

Direct ink write (DIW) is an extrusion-based additive manufacturing (AM) technique that enables superior repeatability, property tuning, and material customization compared to conventional manufacturing techniques. In this research, DIW is used to print silicone foams that must accommodate the thermal expansion of other parts. This expansion requires the material to compress and subsequently recover. Thus, a key performance metric is reducing “compression set” or deformation retained after the material is compressed. For this study, a silicone resin was compounded with a getter material, 1,4 bis(phenylethynyl)benzene (DEB) mixed with carbon-supported palladium (Pd) and printed in a variety of lattice structures. The effects of the filler and print structure on compression set were evaluated. In these experiments, 0.5-inch diameter coupons were compressed to 75% their original height for 22 hours at 70 °C, and the change in height calculated at intervals between 30 minutes and 24 hours post-decompression. The unfilled pad with skin layers had the best compression set at 0.7% ± 0.1%, followed by the unfilled pad with no skins at 1.5% ± 0.1%. As the number of filled layers increased, compression set performance degraded. The pad with filled skin layers and all filled layers had a compression set of 7.0% ± 0.3%. Additionally, the reaction extent of DEB was found to increase compression set, possibly due to the diffusion of DEB to the surface at elevated temperatures. Imaging reveals extensive crystallization at the surface. These investigations show that a non-reinforcing filler will increase compression set but that print structure can mitigate this effect.

36 MATERIALS SCIENCE↗
DOE OSTI2010

Final Report for Grant "Direct Writing via Novel Aromatic Ladder Polymer Precursors"

This report describes activities and findings under the above entitled grant. These pertain to the development of new synthetic routes to novel precursor polymers and oligomers that are applicable for conversion from electrical insulators to electrical conductors under the application of light (e.g. direct photolithographic writing)

36 MATERIALS SCIENCE↗
DOE OSTI2017

Direct Laser Writing of Magneto-Photonic Sub-Microstructures for Prospective Applications in Biomedical Engineering

Here, we report on the fabrication of desired magneto-photonic devices by a low one-photon absorption (LOPA) direct laser writing (DLW) technique on a photocurable nanocomposite consisting of magnetite ( Fe 3 O 4 ) nanoparticles and a commercial SU-8 photoresist. The magnetic nanocomposite was synthesized by mixing Fe 3 O 4 nanoparticles with different kinds of SU-8 photoresists. We demonstrated that the degree of dispersion of Fe 3 O 4 nanoparticles in the nanocomposite depended on the concentration of Fe 3 O 4 nanoparticles, the viscosity of SU-8 resist, and the mixing time. By tuning these parameters, the most homogeneous magnetic nanocomposite was obtained with a concentration of about 2 wt % of Fe 3 O 4 nanoparticles in SU-8 2005 photoresist for the mixing time of 20 days. The LOPA-based DLW technique was employed to fabricate on demand various magneto-photonic submicrometer structures, which are similar to those obtained without Fe 3 O 4 nanoparticles. The magneto-photonic 2D and 3D structures with sizes as small as 150 nm were created. Finally, we demonstrated the strong magnetic field responses of the magneto-photonic nanostructures and their use as micro-actuators when immersed in a liquid solution. View Full-Text

36 MATERIALS SCIENCE↗
DOE OSTI2022

Balancing Functionality and Printability: High-Loading Polymer Resins for Direct Ink Writing

Although direct ink writing (DIW) allows the rapid fabrication of unique 3D printed objects, the resins—or “inks”—available for this technique are in short supply and often offer little functionality, leading to the development of new, custom inks. However, when creating new inks, the ability of the ink to lead to a successful print, or the “printability,” must be considered. Thus, this work examined the effect of filler composition/concentration, printing parameters, and lattice structure on the printability of new polysiloxane inks incorporating high concentrations (50–70 wt%) of metallic and ceramic fillers as well as emulsions. Results suggest that strut diameter and spacing ratio have the most influence on the printability of DIW materials and that the printability of silica- and metal-filled inks is more predictable than ceramic-filled inks. Additionally, higher filler loadings and SC geometries led to stiffer printed parts than lower loadings and FCT geometries, and metal-filled inks were more thermally stable than ceramic-filled inks. The findings in this work provide important insights into the tradeoffs associated with the development of unique and/or multifunctional DIW inks, printability, and the final material’s performance.

36 MATERIALS SCIENCE↗