Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “error rate calculations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Rotational temperature determination in flowing nitrogen using an electron beam

The measurement of rotational temperature by the electron-beam fluorescence technique is investigated for temperatures between 78 K and 300 K by using the 0-0 band of the nitrogen first negative system. Existing methods for calculating the rotational temperature from electron-beam spectra result in values which are higher than the true temperature and the error increases with density and electron-beam current. The errors are believed to arise through neglect of the effects of secondary electrons. Excitation by low-energy secondary electrons can increase the population of the sparsely populated rotational ground states at the expense of the abundantly populated states. This secondary excitation is proposed as the cause of the error in the calculated rotational temperature and a theoretical study determines that the density and beam current govern the excitation rate. Rotational-temperature measurements are made in a flowing stream of nitrogen at a known temperature for a range of densities and beam currents.

Lillicrap, D. C.↗
NASA NTRS1982

Vortex simulation of an inviscid shear layer

The accuracy of the vortex-blob method was tested by simulating a free-shear-layer instability, Kirchhoff's elliptical vortex, and a circular vortex. The main numerical parameters in the vortex-blob method are the density of the vortices, and the distribution of vorticity within each vortex core. The growth rate of a periodic unstable mode of the shear layer was calculated numerically and compared with the exact result. The error is only a few percent for about 10 rows of vortex blobs. The error is reduced by decreasing the spacing between vortices and, correspondingly, the core size. In the simulation of the motion of the elliptical vortex, the rotation of the boundary, without change of shape, and the circular particle paths of the vortical fluid were well simulated. For the circular vortex, optimum sets of parameters were obtained by comparing them with the exact velocity. The results are consistent with convergence theories of the vortex-blob method. In particular, second-order convergence is observed with a Gaussian core from velocity calculation.

Nakamura, Y.↗
NASA NTRS1989

Error detecting capabilities of the shortened Hamming codes adopted for error detection in IEEE Standard 802.3

The error-detecting capabilities of the shortened Hamming codes adopted for error detection in IEEE Standard 802.3 are investigated. These codes are also used for error detection in the data link layer of the Ethernet, a local area network. The weight distributions for various code lengths are calculated to obtain the probability of undetectable error and that of detectable error for a binary symmetric channel with bit-error rate between 0.00001 and 1/2.

Fujiwara, Toru↗
NASA NTRS1989

GPS measurements of strain accumulation across the Imperial Valley, California: 1986-1989

The Global Positioning System (GPS) data collected in southern California from 1986 to 1989 indicate considerable strain accumulation across the Imperial Valley. Displacements are computed at 29 stations in and near the valley from 1986 to 1988, and at 11 sites from 1988 to 1989. The earlier measurements indicate 5.9 +/- 1.0 cm/yr right-lateral differential velocity across the valley, although the data are heavily influenced by the 1987 Superstition Hills earthquake sequence. Some measurements, especially the east-trending displacements, are suspects for large errors. The 1988 to 1989 GPS displacements are best modeled by 5.2 +/- 0.9 cm/yr of valley crossing deformation, but rates calculated from conventional geodetic measurements (3.4 to 4.3 cm/yr) fit the data nearly as well. There is evidence from GPS and Very Long Base Interferometry (VLBI) observations that the present slip rate along the southern San Andreas fault is smaller than the long-term geologic estimate, suggesting a lower earthquake potential than is currently assumed. Correspondingly, a higher earthquake potential is indicated for the San Jacinto fault. The Imperial Valley GPS sites form part of a 183 station network in southern California and northern Baja California, which spans a cross-section of the North American-Pacific plate boundary.

Larsen, Shawn↗
NASA NTRS1992

Global Positioning System measurements of strain accumulation across the Imperial Valley, California - 1986-1989

The Global Positioning System (GPS) data collected in southern California from 1986 to 1989 indicate considerable strain accumulation across the Imperial Valley. Displacements are computed at 29 stations in and near the valley from 1986 to 1988, and at 11 sites from 1988 to 1989. The earlier measurements indicate 5.9 =/- 1.0 cm/yr right-lateral differential velocity across the valley, although the data are heavily influenced by the 1987 Superstition Hills earthquake sequence. Some measurements, especially the east-trending displacements, are suspects for large errors. The 1988 to 1989 GPS displacements are best modeled by 5.2 =/- 0.9 cm/yr of valley crossing deformation, but rates calculated from conventional geodetic measurements (3.4 to 4.3 cm/yr) fit the data nearly as well. There is evidence from GPS and Very Long Base Interferometry (VLBI) observations that the present slip rate along the southern San Andreas fault is smaller than the long-term geologic estimate, suggesting a lower earthquake potential than is currently assumed. Correspondingly, a higher earthquake potential is indicated for the San Jacinto fault. The Imperial Valley GPS sites form part of a 183 station network in southern California and northern Baja California, which spans a cross-section of the North American-Pacific plate boundary.

Larsen, Shawn↗
NASA NTRS1992

A three-parameter approximation for radiative transfer in nonhomogeneous atmospheres - Application to the O3 9.6-micron band

A three-parameter scaling approximation is developed in conjunction with random models for the computation of transmittance along nonhomogeneous atmospheres. In addition to the scaled path length and pressure, a third parameter is introduced to account for intermediate absorption. With reference to the results derived from line-by-line calculations, the accuracy of this scaling approximation is assessed in different atmospheric conditions. For the O3 9.6-micron band where the Curtis-Godson and other conventional scaling methods usually produce large errors, the present model can achieve relative accuracies within about 1 percent in transmittance and the downward surface flux. Accuracy of about 0.15 K/d can be obtained in cooling rate calculations. The present three-parameter approximation is well suited for radiative transfer parameterizations in which the demand for high accuracy is required in the transmittance and flux calculations.

Fu, Qiang↗
DOE OSTI2021

WSF PISA example for SAFER pilot

On October 15, 2021, the Radioactive and Hazardous Waste Management Facility Manager declared a Potential Inadequacy in the Safety Analysis (PISA) due to a new information relating to an error discovered in calculation AB-WSF-20-002. Calculation AB-WSF-20-002 is used to determine source terms and heat release rates for vehicle and aircraft impacts with fuel fires involving TRU waste containers. The source term for an aircraft’s impact has different source terms factors (i.e., DR, ARF, RF, LPF) that are applied to multiple categories of drums impacted in the accident scenario based on the physical stresses of the aircraft impact and involvement in the subsequent fuel pool fire. The source terms of the multiple categories of affected drums are summed to determine the final source term for the accident scenario. Certain categories of affected drums are modeled to lose their lid, causing material to eject and burn unconfined on the ground. For these specific categories, a lower ARF value was incorrectly applied in AB-WSF-20-002 (i.e., an ARF value of 1E-3 was used instead of the DOE-STD-5506-2007 directed ARF value of 1E-2). For these categories, the ARF is applied to a relatively small number of low-activity drums (i.e., 17 drums at 2.9 PE-Ci each) compared to the total number of drums affected (i.e., 166 drums totaling 621.8 PE-Ci). Therefore, this error is not expected to significantly increase final dose for the accident scenario. No immediate actions or compensatory measures are required to maintain the facility in a safe condition.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

In Situ Ion Counting for Improved Implanted Ion Error Rate and Silicon Vacancy Yield Uncertainty

An in situ counted ion implantation experiment improving the error on the number of ions required to form a single optically active silicon vacancy (SiV) defect in diamond 7-fold compared to timed implantation is presented. Here, traditional timed implantation relies on a beam current measurement followed by implantation with a preset pulse duration. It is dominated by Poisson statistics, resulting in large errors for low ion numbers. Instead, our in situ detection, measuring the ion number arriving at the substrate, results in a 2-fold improvement of the error on the ion number required to generate a single SiV compared to timed implantation. Through postimplantation analysis, the error is improved 7-fold compared to timed implantation. SiVs are detected by photoluminescence spectroscopy, and the yield of 2.98% is calculated through the photoluminescence count rate. Hanbury–Brown–Twiss interferometry is performed on locations potentially hosting single-photon emitters, confirming that 82% of the locations exhibit single photon emission statistics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Developing a complete AI-accelerated workflow for superconductor discovery

The quest to identify new superconducting materials with enhanced properties is hindered by the prohibitive cost of computing electron-phonon spectral functions, severely limiting the materials space that can be explored. Here, we introduce a Bootstrapped Ensemble of Equivariant Graph Neural Networks (BEE-NET), a machine-learning model trained to predict the Eliashberg spectral function and superconducting critical temperature with a mean-absolute-error of 0.87 K relative to DFT-based Allen-Dynes calculations. Intriguingly, BEE-NET achieves a true-negative-rate of 99.4%, enabling highly efficient screening for the rare property of superconductivity. Integrated into a multi-stage, AI-accelerated discovery pipeline that incorporates elemental-substitution strategies and machine-learned interatomic potentials, our workflow reduced over 1.3 million candidate structures to 741 dynamically and thermodynamically stable compounds with DFT-confirmed T c > 5 K. We report the successful synthesis and experimental confirmation of superconductivity in two of these previously unreported compounds. This study establishes a data-driven framework that integrates machine learning, quantum calculations, and experiments to systematically accelerate superconductor discovery.

Gibson, Jason B. [Quantum Formatics, Cambridge, MA↗
DOE OSTI2025

Q-Cluster: Quantum Error Mitigation Through Noise-Aware Unsupervised Learning

Quantum error mitigation (QEM) is critical in reducing the impact of noise in the pre-fault-tolerant era, and is expected to complement error correction in fault-tolerant quantum computing (FTQC). In this work, we propose a novel QEM approach, Q-Cluster, that uses unsupervised learning (clustering) to reshape the measured bit-string distribution. Our approach starts with a simplified bit-flip noise model. It first performs clustering on noisy measurement results, i.e., bit-strings, based on the Hamming distance. The centroid of each cluster is calculated using a qubit-wise majority vote. Next, the noisy distribution is adjusted with the clustering outcomes and the bitflip error rates using Bayesian inference. Our simulation results show that Q-Cluster can mitigate high noise rates (up to 40% per qubit) with the simple bit-flip noise model. However, real quantum computers do not fit such a simple noise model. To address the problem, we (a) apply Pauli twirling to tailor the complex noise channels to Pauli errors, and (b) employ a machine learning model, ExtraTrees regressor, to estimate an effective bit-flip error rate using a feature vector consisting of machine calibration data (gate & measurement error rates), circuit features (number of qubits, numbers of different types of gates, etc.) and the shape of the noisy distribution (entropy). Our experimental results show that our proposed Q-Cluster scheme improves the fidelity by a factor of 1.46x, on average, compared to the unmitigated output distribution, for a set of low-entropy benchmarks on five different IBM quantum machines. Our approach outperforms the state-of-art QEM approaches RZNE [28], M3 [24], Hammer [35], and QBEEP [33] by 1.26x,1.29x,1.47x, and 2.65 x, respectively.

42 ENGINEERING↗
DOE OSTI2021

Impact of Flux Wire Selection on Neutron Spectrum Adjustment

In reactor dosimetry, spectrum unfolding methods are used to assess the energy-dependent neutron flux following the irradiation of flux wires or foils. For some spectrum unfolding methods, an a priori, or initial guess, spectrum is necessary. However, if the a priori spectrum is not representative of the irradiation spectrum experienced by the flux wires, the spectrum unfolding method may fail or create a nonphysical adjusted spectrum. The unfolded spectrum is dependent on flux wire reaction rates, and therefore cross section. As a result, each selection or combination of flux wires will have a different sensitivity to the group-wise fluence difference between the a priori spectrum and the irradiation spectrum. Therefore, a selection of flux wires that are insensitive to errors in the a priori spectrum would be considered robust choices for reactor dosimetry. In this work, flux wire reaction rates are calculated using a simulated neutron spectrum from the High Flux Isotope Reactor (HFIR) and spectrum unfolding methods are used in each flux wire combinations. The flux wire combinations are compared against a traditional flux wire set of Ti, Fe, and Co, with a summary table of the deemed “good” wire combinations that are insensitive to number of a priori neutron energy groups, group-wise difference between the a priori and irradiation, and magnitude of difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Rigorous constraints on three-nucleon forces in chiral effective field theory from fast and accurate calculations of few-body observables

We explore the constraints on the three-nucleon force (3NF) of chiral effective field theory (χ EFT) that are provided by bound-state observables in the A = 3 and A = 4 sectors. Our statistically rigorous analysis incorporates experimental error, computational method uncertainty, and the uncertainty due to truncation of the χ EFT expansion at next-to-next-to-leading order. A consistent solution for the 3 H binding energy, the 4 He binding energy and radius, and the 3 H β-decay rate can only be obtained if χ EFT truncation errors are included in the analysis. Here, the β-decay rate is the only one of these that yields a nondegenerate constraint on the 3NF low-energy constants, which makes it crucial for the parameter estimation. We use eigenvector continuation for fast and accurate emulation of no-core shell model calculations of the few-nucleon observables. This facilitates sampling of the posterior probability distribution, allowing us to also determine the distributions of the parameters that quantify the truncation error. We find a χ EFT expansion parameter of Q = 0.33 ± 0.06 for these observables.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRSDate not supplied

Recent Improvements and Verification of A Full Body Model in Opensim

BACKGROUND: The dynamic feasibility [1,2] criterion, that the subject’s Center of Pressure (COP) be located within the Base of Support (BOS) which outlines the feet, has aided in assessing the stability of human motion recorded on earth while performing the recorded tasks in lunar gravity or as countermeasures exercises on a vibration isolation and stabilization system in microgravity. The convex hull of the BOS on the platform under the subject’s feet was estimated using virtual markers on the feet of the scaled subject model. The COP was calculated using the ground reaction forces and moments determined from motion capture data with biomechanical modeling tools [3]. Occasionally, large-amplitude oscillatory spikes or “artifacts” were observed in the subject’s linear and angular momentum derivatives, affecting some COP data derived from motion capture. The purpose of this investigation was to assess and improve the accuracy of model scaling and BOS estimation as well as to determine the efficacy of model adjustments in mitigating artifacts influencing motion capture-derived ground reaction force and COP results. METHODS: To aid evaluation of proposed process and model updates, motion capture data were collected for two subjects during unit test and range of motion trials, lunar tasks, and countermeasures exercise motions. Markers were added to the full body Plug-in Gait marker set [4] during data collection. New markers were placed on the front, back, sides, and top of the head to improve scaling using distances between marker pairs. Medial elbow markers were added to stabilize the upper arm during OpenSim Inverse Kinematics (IK) [5]. Finally, markers were added on the outer edge of the heels and on the outside edges of the first and last toes on each foot. These additional foot markers were made available to test new automated foot scaling techniques and to calculate the error between the subject’s estimated and recorded BOS. The modified unscaled OpenSim Full Body Rajagopal Model [6,7] was adjusted using some previously investigated techniques [8] to mitigate rapid shifts in joint angles occurring during IK, as these were found to cause the spike artifacts observed in subsequent stages of analysis. Since OpenSim models use Euler angles and rotation sequences, the arm axes of rotation were adjusted, and the pelvis order of rotation was changed to minimize the likelihood of encountering “gimbal lock” during common human motion. The model clavicle, arm, elbow, wrist, pelvis, and ankle angle limits were adjusted to better accommodate the full human range of motion seen in exercise and lunar data. The shoulder joint center was calculated using a “pivoting” algorithm [9], and both shoulder joint center and upper arm markers were included during IK to provide additional shoulder stability on a case-by-case basis. The quality of IK results was assessed by three criteria: minimizing error between recorded motion capture markers and model markers, checking for reasonable rates of change in joint angles between fames (i.e., no IK artifacts), and ensuring the absence of spikes in the inertial forces and angular momentum derivatives calculated using a custom OpenSim plugin [10]. RESULTS: The additional markers placed on the subject during data collection allowed the head and feet to be scaled more accurately using distances between new marker pairs. Scaling with BOS markers placed on the subject and removing the limit on subtalar angle resulted in more accurate BOS determination. Unrealistically large changes in joint angles between frames could be reduced by including clavicle, sternum, and medial elbow markers during IK. In cases with large arm ranges of motion, results could be further improved by running IK using medial elbow and virtual shoulder joint center markers. Model adjustments significantly improved the IK results affecting COP calculation and increased the accuracy of BOS estimation.

C A Bell↗
NASA NTRS1994

In Situ Measurements of the NO2/NO Ratio for Testing Atmospheric Photochemical Models

Simultaneous in situ measurements of NO2, NO, O3, ClO, pressure and temperature have been made for the first time, presenting a unique opportunity to test our current understanding of the photochemistry of the lower stratosphere. Data were collected from several flights of the ER-2 aircraft at mid-latitudes in May 1993 during NASA's Stratospheric Photochemistry, Aerosols and Dynamics Expedition (SPADE). The daytime ratio of NO2/NO remains fairly constant at 19 km with a typical value of 0.68 and standard deviation of +/- 0.17. The ratio observations are compared with simple steady-state calculations based on laboratory-measured reaction rates and modeled NO2 photolysis rates. At each measurement point the daytime NO2/NO with its measurement uncertainty overlap the results of steady-state calculations and associated uncertainty. However, over all the ER-2 flights examined, the model systematically overestimates the ratio by 40% on average. Possible sources of error are examined in both model and measurements. It is shown that more accurate laboratory determinations of the NO + O3 reaction rate and of the NO2 cross-sections in the 200-220 K temperature range characteristic of the lower stratosphere would allow for a more robust test of our knowledge of NO(x) photochemistry by reducing significant sources of uncertainties in the interpretation of stratospheric measurements. The present measurements are compared with earlier observations of the ratio at higher altitudes.

Jaegle, L.↗
DOE OSTI2022

Signal-Compensation-Based Adaptive PID Control for Fused Magnesia Smelting Processes

For fused magnesia smelting processes, the proportional-integral-derivative (PID) controller is difficult to regulate the smelting currents within desired ranges due to unexpected variations of the dynamics caused by material feeding operations. To solve this problem, we first proposed its dynamic model composed of a linear model and an uncertain nonlinear dynamic system that describes the unknown time-varying dynamics of nonlinearity and strong couplings among controlled variables. Then, using the accurately calculated value of the uncertain part at the previous sampling time instant and the tracking error that reflects the influence of its change rate, we developed a feedforward and a one-step optimal control to obtain two signal compensators to eliminate the impact of frequent variations of the uncertainties. For the compensators, we proposed a weight selection method to minimize the sum of the squared tracking error with ensured closed-loop stability. Based on the abovementioned modeling and control structure, we finally developed a novel adaptive PID controller augmented with signal compensators to control the whole process. Industrial applications have shown that the proposed method can always keep the tracking error and the control input within their targeted ranges, leading to a significantly reduced energy consumption per ton and increased fused magnesia production.

Wang, Weizhou↗
NASA NTRS1993

Calculation of molecular excitation rates

State-to-state collisional excitation rates for interstellar molecules observed by radio astronomers continue to be required to interpret observed line intensities in terms of local temperatures and densities. A problem of particular interest is collisional excitation of water which is important for modeling the observed interstellar masers. In earlier work supported by a different NASA Grant, excitation of water in collisions with He atoms was studied; after many years of successively more refined calculations that problem now seems to be well understood, and discrepancies with earlier experimental data for related (pressure broadening) phenomena are believed to reflect experimental errors. Because of interstellar abundances, excitation by H2, the dominant interstellar species, is much more important than excitation by He, although it has been argued that rates for excitation by these are similar. Under the current grant theoretical study of this problem has begun which is greatly complicated by the additional degrees of freedom which must be included both in determining the interaction potential and also in the molecular scattering calculation. We have now computed the interaction forces for nearly a thousand molecular geometries and are close to having an acceptable global fit to these points which is necessary for the molecular dynamics calculations. Also, extensive modifications have been made to the molecular scattering code, MOLSCAT. These included coding the rotational basis sets and coupling matrix elements required for collisions of an asymmetric top with a linear rotor. A new method for numerical solution of the coupled equations has been incorporated. Because of the long-ranged nature of the water-hydrogen interaction it is necessary to integrate the equations to rather large intermolecular separations, and the integration methods previously available in MOLSCAT are not ideal for such cases. However, the method used by Alexander in his HIBRIDON code is particularly suited for such cases. We have obtained this code and incorporated that part which solves the coupled differential equations as an option in the MOLSCAT program.

Flynn, George↗
NASA NTRS1988

Precise interferometric tracking of spacecraft at low sun-earth-probe angles

When a spacecraft is at low sun-earth-probe (SEP) angle, phase perturbations induced in the spacecraft's signal by the solar plasma can impede the acquisition of meaningful spacecraft Very Long Baseline Interferometry (VLBI) measurements. This phenomenon imposes limitations on our ability to successfully acquire the spacecraft signal, and also introduces unmodeled errors into data that are successfully acquired. In this paper, an analysis of the solar plasma induced error on interferometric delay rate as a function of SEP angle is performed. In addition, the probability of correct signal phase connection as a function of SEP angle and plasma variability is calculated for 2.3 GHz and 8.4 GHz signals. In December 1986, an experiment was conducted to demonstrate VLBI navigation at low SEP angles, using the Voyager 2 spacecraft. The results of this experiment are consistent with the conclusions reached in the low SEP analysis and are also consistent with a theoretical error model for water vapor fluctuations in the earth's troposphere.

Kahn, Robert D.↗
NASA NTRS1977

Turbulent viscosity and Jupiter's tidal Q

A recent estimate of tidal dissipation by turbulent viscosity in Jupiter's convective interior predicts that the current value of the planet's tidal Q is roughly 5 million. We point out a fundamental error in this calculation, and show that turbulent dissipation alone implies that at present Q is about 50 trillion. Our reduced estimate for the rate of tidal dissipation shows conclusively that tidal torques have produced only negligible modifications of the orbits of the Galilean satellites over the age of the solar system.

Goldreich, P.↗