Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “directed assembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Test Capabilities of the NASA Langley Direct Connect Supersonic Combustion Test Facility

In 1969 a combustion-heated direct-connect test facility was assembled at the NASA Langley Research Center and used to support NASA’s Hypersonic Research Engine program. Later, the facility was used to support NASA’s generic hypersonic program, assessing the mixing, ignition, flame holding, and combustion characteristics of ramjet and scramjet combustors. Over the years, the facility has been updated and modified to conduct increasingly complicated tests. Today, the facility is known as the Direct Connect Supersonic Combustion Test Facility (DCSCTF) and is part of the NASA Langley Scramjet Test Complex. Recently, the facility has been used by external customers to test fuel-cooled and uncooled, flight-like test articles. Tests have been conducted at nominal Mach 5 flight conditions for up to 15 minutes of continuous operation. The facility remains a viable and useful tool in the support of various Department of Defense projects.

Diego P Capriotti↗
NASA NTRS2004

Inducer Hydrodynamic Forces in a Cavitating Environment

Marshall Space Flight Center has developed and demonstrated a measurement device for sensing and resolving the hydrodynamic loads on fluid machinery. The device - a derivative of the six-component wind tunnel balance - senses the forces and moments on the rotating device through a weakened shaft section instrumented with a series of strain gauges. This rotating balance was designed to directly measure the steady and unsteady hydrodynamic loads on an inducer, thereby defining the amplitude and frequency content associated with operating in various cavitation modes. The rotating balance was calibrated statically using a dead-weight load system in order to generate the 6 x 12 calibration matrix later used to convert measured voltages to engineering units. Structural modeling suggested that the rotating assembly first bending mode would be significantly reduced with the balance s inclusion. This reduction in structural stiffness was later confirmed experimentally with a hammer-impact test. This effect, coupled with the relatively large damping associated with the rotating balance waterproofing material, limited the device s bandwidth to approximately 50 Hertz Other pre-test validations included sensing the test article rotating assembly built-in imbalance for two configurations and directly measuring the assembly mass and buoyancy while submerged under water. Both tests matched predictions and confirmed the device s sensitivity while stationary and rotating. The rotating balance was then demonstrated in a water test of a full-scale Space Shuttle Main Engine high-pressure liquid oxygen pump inducer. Experimental data was collected a scaled operating conditions at three flow coefficients across a range of cavitation numbers for the single inducer geometry and radial clearance. Two distinct cavitation modes were observed symmetric tip vortex cavitation and alternate-blade cavitation. Although previous experimental tests on the same inducer demonstrated two additional cavitation modes at lower inlet pressures, these conditions proved unreachable with the rotating balance installed due to the intense dynamic environment. The sensed radial load was less influenced by flow coefficient than by cavitation number or cavitation mode although the flow coefficient range was relatively narrow. Transition from symmetric tip vortex to alternate-blade cavitation corresponded to changes in both radial load magnitude and radial load orientation relative to the inducer. Sensed moments indicated that the effective load center moved downstream during this change in cavitation mode. An occurrence of "higher+rdex cavitation" was also detected in both the stationary pressures and the rotating balance data although the frequency of the phenomena was well above the reliable bandwidth of the rotating balance. In summary the experimental tests proved both the concept and device s capability despite the limitations and confirmed that hydrodynamically-induced forces and moments develop in response to the unbalanced pressure field, which is, in turn, a product of the cavitation environment.

Skelley, Stephen E.↗
NASA NTRS1992

Structure and kinematics of a major tectonic contact, Michipicoten greenstone belt, Ontario

The Michipicoten greenstone belt, Ontario, experienced a complex history of folding, faulting, and fabric development. Near Wawa, a major east-west contact, here named the Steep Hill Falls (SHF) contact, extends entirely across the belt. The SHF contact is both an angular unconformity and a fault and is interpreted to be a regionally significant tectonic contact separating distinct northern and southern terranes, both of which include volcanic rocks of probable island-arc origin. The amount of horizontal transport involved in bringing the two terranes together along the SHF contact is not known. Mapping and structural analysis suggest that regionally significant horizontal displacements took place, with movement vectors that changed with time. Early faults, folds, and fabrics imply north-south to northeast-southwest (with respect to present directions) convergence, with a vergence reversal occurring during this complex event. The most likely models infer early south vergence and later north vergence. Transecting the earliest structures are younger (but still Archean) northeast-striking steep cleavages with associated upright folds that may relate to northwest-southeast assembly of the Superior Province craton. The craton assembly event thus involved a transport direction at a high angle to that inferred for the earlier assembly of the Michipicoten greenstone belt.

Mcgill, George E.↗
NASA NTRS1974

Scanning nozzle plating system

A plating system is described in which a substrate to be plated is supported on a stationary platform. A nozzle assembly with a small nozzle is supplied with a plating solution under high pressure, so that a constant-flow stream of solution is directed to the substrate. The nozzle assembly is moved relative to the substrate at a selected rate and movement pattern. A potential difference (voltage) is provided between the substrate and the solution in the assembly. The voltage amplitude is modulated so that only when the amplitude is above a minimum known value plating takes place.

Oliver, G. D.↗
NASA NTRS1985

Variable length strut with longitudinal compliance and locking capability

A variable length strut device is illustrated for connecting two associated structures which includes an outer load bearing shell, a drive assembly, a length varying compliance assembly positioned by drive assembly, and a strut rod locking assembly. The load bearing shell includes a connecting part adapted for connection to a first associated structure. A strut connection rod has a connecting part adapted for connection to a second associated structure and a distal end having a piston driver slidably carried in a housing of compliance assembly. Two compliance pistons act in opposing directions on the piston driver to provide longitudinal compliance in a compliance mode of operation. Locking assembly includes locking balls which are urged in a locking ring as locking bolt is urged to the left by fluid pressure. Microswitches sense the displacement of pistons away from the internal ring to bring the pistons to a neutral position wherein the pistons are in contact with the internal ring when it is desired to do so as affected by a control source.

Belew, R. R.↗
NASA NTRS2014

Partial Arc Curvilinear Direct Drive Servomotor

A partial arc servomotor assembly having a curvilinear U-channel with two parallel rare earth permanent magnet plates facing each other and a pivoted ironless three phase coil armature winding moves between the plates. An encoder read head is fixed to a mounting plate above the coil armature winding and a curvilinear encoder scale is curved to be co-axis with the curvilinear U-channel permanent magnet track formed by the permanent magnet plates. Driven by a set of miniaturized power electronics devices closely looped with a positioning feedback encoder, the angular position and velocity of the pivoted payload is programmable and precisely controlled.

Sun, Xiuhong↗
NASA NTRS1978

Some results from 1/8-scale Shuttle model vibration studies

Highlights of experimental and analytical vibration studies of a 1/8-scale structural dynamic model of the Space Shuttle are presented. The Space Shuttle is a launch vehicle with elements assembled in an asymmetric manner. Responses of the assembled vehicle are characterized by directional coupling and high modal density at low frequencies. Effects of distortion of structure near element interfaces are shown to be significant and predictable with highly detailed mathematical models. Acquisition of modal data by single-point random excitation is shown to be viable for these complex structures. Element studies reveal large liquid-structure interactions and a wide range of structural damping.

Pinson, L. D.↗
NASA NTRS1981

A BAPTA employing rotary transformers, stepper motors and ceramic ball bearings

The utilization of rotary transformers as an alternative to slip rings for the power transfer from solar panels to a satellite's main body could be advantageous, especially if an ac bus system is taken into consideration. Different approaches with main emphasis on the electromagnetic design were investigated and showed efficiencies of up to 99% with a 3 kW power capability. A solidly preloaded pair of ball bearings with ceramic balls assures proper transformer air gaps and acceptable torque changes over temperature and temperature gradients. The bearing and power transfer assembly is driven by a direct drive stepper motor with inherent redundancy properties and needs no caging mechanism.

Auer, W.↗
NASA NTRS1985

Manipulator for Heating and Cooling in Ultrahigh Vacuum

In sample-transfer system for use in ultrahigh vacuum, samples mounted on threaded circular holder transferred to flip mechanism of manipulator by simple translation and rotation. Flip mechanism contains electrode assembly and thermocouple that make direct contact with sample. Copper plate and flexible strap attached to receiving block to cool sample. Simple modifications allow broad range of sample temperatures (150 to 1,750 K) and direct temperature measurements, while retaining advantage of additional degree of freedom provided by flip mechanism of precise manipulator.

Outlaw, R.↗
NASA NTRS2005

Parallel Domain Decomposition Formulation and Software for Large-Scale Sparse Symmetrical/Unsymmetrical Aeroacoustic Applications

The overall objectives of this research work are to formulate and validate efficient parallel algorithms, and to efficiently design/implement computer software for solving large-scale acoustic problems, arised from the unified frameworks of the finite element procedures. The adopted parallel Finite Element (FE) Domain Decomposition (DD) procedures should fully take advantages of multiple processing capabilities offered by most modern high performance computing platforms for efficient parallel computation. To achieve this objective. the formulation needs to integrate efficient sparse (and dense) assembly techniques, hybrid (or mixed) direct and iterative equation solvers, proper pre-conditioned strategies, unrolling strategies, and effective processors' communicating schemes. Finally, the numerical performance of the developed parallel finite element procedures will be evaluated by solving series of structural, and acoustic (symmetrical and un-symmetrical) problems (in different computing platforms). Comparisons with existing "commercialized" and/or "public domain" software are also included, whenever possible.

Nguyen, D. T.↗
NASA NTRS1999

Multifunction automated crawling system

The present invention is an automated crawling robot system including a platform, a first leg assembly, a second leg assembly, first and second rails attached to the platform, and an onboard electronic computer controller. The first leg assembly has an intermittent coupling device and the second leg assembly has an intermittent coupling device for intermittently coupling the respective first and second leg assemblies to a particular object. The first and second leg assemblies are slidably coupled to the rail assembly and are slidably driven by motors to thereby allow linear movement. In addition, the first leg assembly is rotary driven by a rotary motor to thereby provide rotary motion relative to the platform. To effectuate motion, the intermittent coupling devices of the first and second leg assemblies alternately couple the respective first and second leg assemblies to an object. This motion is done while simultaneously moving one of the leg assemblies linearly in the desired direction and preparing the next step. This arrangement allows the crawler of the present invention to traverse an object in a range of motion covering 360 degrees.

Bar-Cohen, Yoseph↗
NASA NTRS2009

Improved Joining of Metal Components to Composite Structures

Systems requirements for complex spacecraft drive design requirements that lead to structures, components, and/or enclosures of a multi-material and multifunctional design. The varying physical properties of aluminum, tungsten, Invar, or other high-grade aerospace metals when utilized in conjunction with lightweight composites multiply system level solutions. These multi-material designs are largely dependent upon effective joining techAn improved method of joining metal components to matrix/fiber composite material structures has been invented. The method is particularly applicable to equipping such thin-wall polymer-matrix composite (PMC) structures as tanks with flanges, ceramic matrix composite (CMC) liners for high heat engine nozzles, and other metallic-to-composite attachments. The method is oriented toward new architectures and distributing mechanical loads as widely as possible in the vicinities of attachment locations to prevent excessive concentrations of stresses that could give rise to delaminations, debonds, leaks, and other failures. The method in its most basic form can be summarized as follows: A metal component is to be joined to a designated attachment area on a composite-material structure. In preparation for joining, the metal component is fabricated to include multiple studs projecting from the aforementioned face. Also in preparation for joining, holes just wide enough to accept the studs are molded into, drilled, or otherwise formed in the corresponding locations in the designated attachment area of the uncured ("wet') composite structure. The metal component is brought together with the uncured composite structure so that the studs become firmly seated in the holes, thereby causing the composite material to become intertwined with the metal component in the joining area. Alternately, it is proposed to utilize other mechanical attachment schemes whereby the uncured composite and metallic parts are joined with "z-direction" fasteners. The resulting "wet" assembly is then subjected to the composite-curing heat treatment, becoming a unitary structure. It should be noted that this new art will require different techniques for CMC s versus PMC's, but the final architecture and companion curing philosophy is the same. For instance, a chemical vapor infiltration (CVI) fabrication technique may require special integration of the pre-form and

Semmes, Edmund↗
NASA NTRS2017

Development of the European Service Module Propulsion Subsystem for the Multi-Purpose Crew Vehicle

Hardware Heritage Schedule limitations and budget constraints drove the need for extensive use of heritage hardware designs. In some cases (OMS and TVC) flight hardware reuse (from Shuttle) was required,and will be delta-qualified for use on Orion Primary sources of heritage: ATV Shuttle Orion CM PSS Ariane 5 EPS Targeted Development Testing Component development testing was performed to address the highest risk areas of heritage design compliance with Orion requirements Assembly level development testing was performed to understand complex assemblies and component interactions Heritage Direct re-use of assets from Shuttle Orbiters, all assets have varying flight history. Orion Use Used by Orion to gimbal the main engine during major translational maneuvers Development Testing Random vibration on controller box (lead to card retention design mod) Design Changes (only as required) Circuit board retention in controller box (single instance from Shuttle flight history) New, longer harnesses Basic Specs(8) fixed position engines Thrust: 105 lbf Nozzle area ratio: 164:1 Orion Use Nominally used for separation maneuvers and mid-course correction maneuvers In contingency scenario (failed main engine), used for major translational maneuvers Drives the need for long continuous duration firing Drives the need for off-pulsing (to steer) Control authority requires 50 duty cycle Development Testing Random Vibration (added vibration isolation bracket) Hot fire, duty cycle (changed MR)

pressure fed↗
NASA NTRS1948

Measurements of the Lateral and Directional Stability and Control Characteristics of a P-51H Airplane (AAF No. 44-64164)

Flight tests of a P-51H airplane with two different vertical-tail assemblies were made to determine lateral and directional stability and control characteristics. The airplane had satisfactory directional stability in the landing, approach, and wave-off conditions with either tail. In the power-on clean and glide conditions, however, the airplane had weak directional stability with the original tail. The production tail, which had a 7-inch fin extension and a shorter span rudder, improved the directional stability in the power-on clean and glide conditions, but the stability was still weak in the power-on clean condition. Increased altitude in either case caused a slight decrease in the stability. The rudder-trim-force change with speed with either vertical-tail assembly was high. The general aileron control characteristics were satisfactory but the aileron effectiveness failed to meet the Army handling-qualities requirements.

Kraft, Christopher C., Jr.↗
NASA NTRS2003

Method for providing concentricity of pilot fuel assembly in a combustor

Concentric installation of a pilot fuel assembly in an opening in a gas turbine combustor casing is achieved by providing a boss having at least two flat surfaces which are perpendicular to each other on the combustor casing surrounding the opening and a mounting flange having at least two flat surfaces which are perpendicular to each other on the pilot fuel assembly. The pilot fuel assembly is concentrically installed to the combustor casing by inserting the assembly into the combustor casing opening, and moving the pilot fuel assembly as far as it will go in a first direction substantially parallel to one of the flat boss surfaces. The distance between the other flat boss surface and one of the flat flange surfaces is then taken. Next, the pilot fuel assembly is moved in the direction opposite the first direction, at which point, the distance between the same two flat surfaces is again measured. Lastly, the pilot fuel assembly is located at a position where the distance between the two measuring surfaces is equal to the average of the first and second measurements. If desired, these steps can be repeated back and forth along an axis perpendicular to the first and second directions.

Halila, Ely E.↗
NASA NTRS1978

High-temperature solar converter

Converter has parabolic concentrator that directs sunlight on three-dimensional absorber assembly within an evacuated glass cylinder. No tracking mechanism is required. Concentrator aperture is adjustable to modify concentration in direct or diffuse sunlight. Range of adjustment is small.

Ascher, G.↗
NASA NTRS2013

Demonstrating the Effect of Particle Impact Dampers on the Random Vibration Response and Fatigue Life of Printed Wiring Assemblies

In a recent experimental study, small Particle Impact Dampers (PID) were bonded directly to the surface of printed circuit board (PCB) or printed wiring assemblies (PWA), reducing the random vibration response and increasing the fatigue life. This study provides data verifying practicality of this approach. The measured peak strain and acceleration response of the fundamental out of plane bending mode was significantly attenuated by adding a PID device. Attenuation of this mode is most relevant to the fatigue life of a PWA because the local relative displacements between the board and the supported components, which ultimately cause fatigue failures of the electrical leads of the board-mounted components are dominated by this mode. Applying PID damping at the board-level of assembly provides mitigation with a very small mass impact, especially as compared to isolation at an avionics box or shelf level of assembly. When compared with other mitigation techniques at the PWA level (board thickness, stiffeners, constrained layer damping), a compact PID device has the additional advantage of not needing to be an integral part of the design. A PID can simply be bonded to heritage or commercial off the shelf (COTS) hardware to facilitate its use in environments beyond which it was originally qualified. Finite element analysis and test results show that the beneficial effect is not localized and that the attenuation is not due to the simple addition of mass. No significant, detrimental reduction in frequency was observed. Side-by-side life testing of damped and un-damped boards at two different thicknesses (0.070" and 0.090") has shown that the addition of a PID was much more significant to the fatigue life than increasing the thickness. High speed video, accelerometer, and strain measurements have been collected to correlate with analytical results.

Knight, Brent↗
NASA NTRS2019

Direct-Write Printing on Three-Dimensional Geometries for Miniaturized Detector and Electronic Assemblies

Aerosol Jet Printing (AJP) and other additive electronics technologies will enable new detector assemblies that were not previously possible with traditional assembly processes. This technology has the potential to reduce mass and volume for fabrication and assembly of detector, instrument and electronics concepts by reducing trace widths down to 10 microns, printing on complex geometries, and allowing new concept production. This poster summarizes development efforts of printed interconnects for space applications.

Printed Hybrid Electronics↗