Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “back stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

116 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

ADDITIVE MANUFACTURING AND REGULATORY TESTING OF CANISTERS FOR SPENT NUCLEAR FUEL MANAGEMENT

The back end of the fuel cycle focuses on the interim storage, transportation, and final disposition of the spent nuclear fuel from nuclear reactors. Commercial light water nuclear power stations across the United States operate with fuel assemblies being irradiated for up to 6 years (planned) in the reactor pressure vessel. After their planned irradiation, the fuel assemblies are moved to a spent fuel pool within the facility complex. After the spent nuclear fuel is removed from the fuel pool, it is typically inserted into a welded metal canister that can be transferred between overpacks for storage, transportation and possibly disposal. Most dry storage systems being used by industry today use dual purpose canisters (DPCs), designed for use in storage and transportation overpacks, but not specifically designed for disposal. Triple purpose-canisters, designed for disposal in addition to storage and transportation, have also been researched. Traditional manufacturing methods for spent fuel canisters involve fusion welding along the length or circumference of the canister which results in high tensile residual stresses in the joint weld zone (WZ) and heat affected zone (HAZ). In this paper, spent fuel canister designs were printed by wire arc additive manufacturing (AM) using the 316L SS welding wire to demonstrate: 1. Feasibility of spent nuclear fuel canister fabrication using this advanced manufacturing method, 2. Dynamic response of the additive manufacture canister design when subjected to the federally mandated Normal Conditions of Transport (NCT) and Hypothetical Accident Conditions (HAC) physical tests for Type B packages. This paper will focus on the canister printing design and structural tests. The AM 3D printed design, regulatory testing, and post-test evaluation of the canister tested to the 10 CFR 71.71 and 10 CFR 71.73 requirements will be presented. One AM canister design was subjected to the penetration, free drop, and puncture test. Before and after the dynamic structural tests, the AM canister design was scanned with a handheld scanner to capture a 3D CAD geometry to compare to the 3D printed canister design in the deformed shape. The scanned geometry was sectioned in areas with deformation and the cross-section profile was measured to determine accurate and repeated results of the deformed shape of the AM canister design.

Martinez, Oscar↗
DOE OSTI2022

Considerations for Hydride Moderator Readiness in Microreactors

The emergence of microreactor technology has helped to drive supporting nuclear materials qualification and acceptance processes. One essential component in these small reactors is a solid moderator, which typically consists of metal hydride and cladding. While the behavior and performance of metal-hydride moderators go back to early advanced reactor development for nuclear-powered aviation and space propulsion, there remains a knowledge gap in the understanding of hydrogen transport–related phenomena and irradiation performance for hydride moderators. This impacts the acceptance/qualification of hydride moderators for microreactors. The goal of this technical note is to lay out a potential path forward for advanced moderator qualification and acceptance for designers and developers of microreactors. The proposed approach has benefited from a model microreactor core with the design parameters of a hydride moderator. Based on the model core and design parameters, a simple chart was developed for the major challenges of hydride moderators where potential incidents, causes, effects, and resolutions are described. The relation between the offered resolutions and the maturity of the metal-hydride moderator technology was emphasized using technological readiness. Technological readiness levels (TRLs) were clustered to three sets: physical phenomena related, reactor irradiations, and system demonstration. Some essential needs to fill the knowledge gaps are discussed for physical phenomena–related TRLs. For reactor irradiations, the importance of identifying goals and priorities is stressed to reach certain TRLs. For system demonstration, it is noted that metal-hydride moderator qualification must comply with the overall microreactor design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Autonomous Inversion of In Situ Deformation Measurement Data for Injection-Induced Stress Change

Geologic carbon storage (GCS) is likely to play a key part of the global effort to dramatically reduce CO2 emissions and perhaps even reduce atmospheric CO2 concentrations through carbon negative operations. A critical part of effort to commercialize and widely deploy this technology is developing the capability to rapidly assimilate real-time monitoring data into a form that will enable site operators to make decisions to manage the safe and efficient operations. Two of the risks associate with GCS are the risk of inducing fractures in the sealing formations that can create leakage pathways and the risk of inducing earthquakes of sufficient magnitude to cause public concern, property damage, or safety risks. To properly manage these risks the site operator needs to know the initial state of stress, the change in stress induced by injection, and the relationship between operational parameters such as injection rate and pressure and the change in stress. Current methods of estimating the change in stress require choosing the type of constitutive model and the model parameters based on core, log, and geophysical data during the characterization phase, with little feedback from operational observations to validate or refine these choices. These characterization methods interrogate the geologic formations using length scales, loading rates or magnitudes that are quite different from those encountered by the actual storage system. It is shown that errors in the assumed constitutive response, even when informed by laboratory tests on core samples, are likely to be common, large, and underestimate the magnitude of stress change caused by injection. Recent advances in borehole-based strain instruments and borehole and surface-based tilt and displacement instruments have now enabled monitoring of the deformation of the storage system throughout its operational lifespan. This data can enable validation and refinement of the knowledge of the geomechanical properties and state of the system, but brings with it a challenge to transform the raw data into actionable knowledge. We demonstrate a method that uses automatic differentiation and a finite-element based geomechanical model perform a gradient-based deterministic inversion of geomechanical monitoring data. This approach allows autonomous integration of the instrument data without the need for time consuming manual interpretation and selection of updated model parameters. Furthermore, only isotropic linear elasticity is considered in this paper, the approach presented is very flexible as to what type of geomechanical constitutive response can be used. The approach is easily adaptable to nonlinear physics-based constitutive models to account for common rock behaviors such as creep and plasticity. The approach also enables training of machine learning-based constitutive models by allowing back propagation of errors through the finite element calculations. This enables strongly enforcing known physics, such as conservation of momentum and continuity, while allowing data-driven models to learn the truly unknown physics such as the constitutive or petrophysical responses.

Burghardt, Jeffrey A.↗
DOE OSTI2022

Design of Phase-Change Thermal Storage Device in a Heat Pump for Building Electric Peak Load Shaving: Preprint

Replacing carbon-intensive fossil fuel heating systems with electric heat pumps powered by renewables is a promising approach to decarbonize the building sector. However, one of the technical barriers of this approach is the large scale of heat demand, which will put excessive stress on the electricity grid. Integrating thermal energy storage (TES) into the heating systems can help alleviate this problem, by shifting thermal load and thus shaving peaks in the building electric load. Therefore, it is critical to understand how to design a thermal storage device in a heat pump for peak load shaving. In this study, we developed a numerical model for a cascaded vapor compression heat pump system integrating a phase change thermal storage device. This novel system can control the net thermal charging and discharging rate of the TES independently from the building's thermal load, which allows for precise control of electric power use. In the current study, we controlled the system to shave building electric peak load during a cold winter morning, and to charge TES during the relatively warm afternoon while still providing space heating. We used the model to evaluate the system performance with and without peak shaving. We also investigated the effect of PCM transition Tt on the peak reduction and electric energy saving potentials. The results show that peak shaving scheme effectively reduces the peak electric power consumption during a predefined discharge time window. When comparing to the no shaving case, for PCM Tt = 10 degrees C, the peak electric load reduction is 23.5%. When comparing to an air-source heat pump with back up electric heater, as Tt increases from 0 to 20 degrees C, the peak reduction increases from 46.1% to 50.9%. Integrating PCM Tt = 10 degrees C with peak shaving leads to the 45.5% of electric energy saving, which is the highest among the three transition temperatures.

electric energy saving↗
DOE OSTI2025

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗
DOE OSTI2020

Conifer water use patterns in the East River Watershed, Colorado US, based on stable water isotopes and cellulose isotopes

This data package contains a series of datasets aimed at understanding the seasonal origins of water used by the dominant conifer species, Abies lasiocarpa and Picea engelmannii, in the East River Watershed. There is a distinct difference in the stable isotopic ratio of summer rain and snowpack and thus by tracking the isotopic ratio of the xylem water in trees, it is possible to separate when a tree is using snow vs. summer rain. Following typical protocols, we sampled and extracted water from soils in the "Research Meadow" near Gothic, CO within the East River Watershed through the 2016 growing season. The stable isotopic ratio of these waters were then measured. Using values of the isotopic ratio of precipitation and snowpack from that season, we develop a mixing model to show how the trees transitioned from use of snowpack to summer in late July. We extended the information on the seasonal origins of water from 2016 back until 1980 by using measurements of the isotopic ratio of cellulose from trees in the Research Meadow. The isotopic ratio of tree ring cellulose records a signal both of the Vapor Pressure Deficit at the leaf-atmosphere boundary and also the source water for the trees. We concluded from this extended analysis that the trees underwent transitions between periods where snow was the dominant water source and summer rain was the dominant water source. More details on this analysis can be found in the publication: Persistence and Plasticity in Conifer Water Use Strategies. JGR Biogeoscience. DOI 10.1029/2018JG004845. The dataset specifically includes stable isotope measurements of xylem and soil water for Spruce and Fir trees at the Rocky Mountain Biological Lab's Research Meadow as well as snowpack and precipitation stable isotopes from nearby National Atmospheric Deposition Program sites. Associated meteorological data is included, which is needed to understand the source water for the trees based on the cellulose measurements.This dataset was updated in June 2021 also include intra-ring measurements of the d18O and d13C of cellulose these same species of trees at the Ziegler Reservoir site in Snowmass, CO. These are listed as files: "Interglaciald18OCellulose.csv", "Interglaciald13OCellulose.csv" and "Modernd13CCellulose.csv". The intent of these measurements was to assess whether common conifers (abies and picea) had undergone ecophysiological or ecohydrological changes during the last period in Earth's history was warmer than today, i.e. the last Interglacial (116,000 to 130,000 years ago). This site was chosen because it is a location where subfossil wood from this critical warm period was discovered. We measured the d18O and d13C of the subfossil trees following the same protocol as the modern samples which included chemical extraction of cellulose and isotope ratio mass spectrometry. We found that the trees showed little difference in water use efficiency but utilized more summer rain during the interglacial period. This analysis and detailed methods are provided in the following manuscript: Wetter summers mitigated temperature stress on Rocky Mountain forests during the last interglacial warm period which is in revision at GRL but is available as a preprint here: 10.1002/essoar.10506740.2

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Pilot Development Progress to Demonstrate Electric Thermal Energy Storage (ETES) Using Low-Cost Particles

The rapid growth of future energy demand increases the need to economically store electrical energy over durations up to several days in long-duration energy storage (LDES) applications. LDES can reduce the grid stress for improving the resilience of the grid. The integration of renewable power and storage has several significant and positive impacts including expanding the renewable energy portion of electricity generation, meeting peak-load demand, and coordinating supply and demand. Several energy storage approaches including mechanical, chemical and electrochemical methods are currently deployed or under development. However, LDES requirements pose unique challenges for scalability, energy capacity, and cost. Thermal energy storage (TES) has the ability to store a large capacity of energy with improved site flexibility compared to incumbent LDES technologies (i.e., pumped hydro) and has attracted significant interest. Our development in TES technology using solid particles as the storage medium has shown feasibility and potential in serving LDES purposes. Particle TES has various advantages over commercialized molten nitrate salt TES and has emerged as a promising storage technology originating from Generation 3 concentrating solar power (CSP) development. Stable, inexpensive silica sand produced in the Midwestern U.S. was identified as a suitable storage medium and has been validated through lab heating and cycling tests. We have successfully developed particle TES for bidirectional electric energy storage to broaden the applications for TES beyond CSP technologies and into standalone electric-thermal energy storage (ETES) systems. Key component designs and performance were verified with prototype testing and model simulations. The ETES system uses high-temperature, low-cost particle thermal energy storage coupled with a unique pressurized fluidized bed heat exchanger that supports a high-efficiency, air-Brayton combined power cycle. At times of low energy demand or high renewable production, an electric particle heater heats large quantities of solid particles to high temperatures in excess of 1100 degrees C. The particles are stored in internally insulated silos. At times of high electricity demand, the hot particles are gravity-fed through the heat exchanger where stored thermal energy is transferred to the power cycle working fluid to drive the gas turbine power generation system, thereby converting the thermal energy back into electricity for the grid. The cold particles leaving the heat exchanger are returned to the storage silos by a well-insulated particle conveyor. This ETES technology using particle TES can be sited anywhere and is predicted to be economic and efficient. Moreover, this ETES technology could be co-located with a retired coal or gas plant to leverage existing power generation and grid infrastructure. Our work has focused on the development of each of the key components (e.g., the electric particle heater, particle storage silos, and the particle-to-gas pressurized fluidized bed heat exchanger) through conceptual designs, prototype testing, and computational modeling. These developments demonstrate technological feasibility and are an important step towards the next phase of development of this promising LDES technology. This presentation will show the progress in developing a pilot demonstration of the ETES system on a commercially relevant scale.

25 ENERGY STORAGE↗
DOE OSTI2022

Computational Modeling of Multi-Pass Rolling Parameters Effect on Resulting Fuel Foil Shape

A focus of the U.S. Department of Energy is to improve production yield and reduce the cost of Low Enriched Uranium (LEU)-molybdenum alloy (U-10Mo) monolithic fuel plates that will be replacing High Enriched Uranium (HEU) oxide dispersion fuels used currently in the United States High Performance Research Reactors (USHPRR). One area of improvement is lowering the high transverse waviness and longitudinal waviness currently present within rolled foils prior to cladding to produce fuel plates. Traditional rolling manufacturing techniques for other metal foils use winders to pull and straighten the foil as it is rolled back and forth to the final thickness. This approach cannot be used to roll thin U-10Mo foils (0.008-0.025” thick) because only small castings can be rolled due to nuclear criticality safety concerns. As a result, the fuel foils are too short (1 m in length) to use traditional winders. Therefore, it is crucial to identify other rolling parameters (i.e., roller friction, axial tension load, roller diameter, and roll pass reduction percent) that might reduce transverse waviness and longitudinal waviness in the rolled fuel foil and develop a high-yield, low-cost multi-pass rolling manufacturing process. This report documents a systematic finite element modeling study to investigate the effects of numerous rolling parameters to reduce resulting transverse waviness and longitudinal waviness in the fuel foil during multi-pass rolling of U-10Mo foils. The rolling of a U-10Mo plate with initial dimensions of 1”x1”x 0.048” is modeled using Abaqus CAE. This rolling is modeled to undergo eight 20% reduction roll passes to a final fuel foil thickness of 0.01”. The elastic-plastic constitutive model of the U-10Mo alloy was input to the fuel foil rolling model. The rollers were modeled as rigid bodies. A comparison of rolling friction coefficients of 0.3 and 0.7 over a wide range of applied axial tension loads were investigated in order to evaluate the effect of using a lubricant during rolling. The effect of roller diameter on the resulting transverse waviness and longitudinal waviness of the fuel foil over a wide range of axial tension loads were also investigated by modeling rollers 7/8” and 3.75” in diameter. The results of this systematic finite element method study will aid manufacturers in producing low transverse waviness and reduced longitudinal waviness in U-10Mo fuel foils.

U-10Mo, FEA, Rolling, Residual Stress, Fuel Foil↗