Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel assembly design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Introduction of the PELICAN loop, a Full-Scale Pressure Drop Test Facility

The Versatile Test Reactor (VTR) is a test reactor currently under development by the US Department of Energy. This reactor will rely on fast neutrons enabling novel and wide-ranging experiment to support the development of the various advanced reactor technologies. With the high flux achievable, accelerated testing of fluid and materials will be made possible. To support VTR design efforts [1], an experimental facility has been designed and constructed at Argonne National Laboratory to recreate the hydraulic flow conditions within the VTR’s primary heat transport system (PHTS). This facility, the Pressure drop Experimental Loop for Investigations of Core Assemblies in advanced Nuclear reactors, PELICAN, measures the pressure drop across a full-scale fuel assembly containing prototypic axial reflectors, fuel, and plena components. Here, we first describe the design considerations required to recreate aspects of the VTR. Then we discuss the design and construction of PELICAN to address these design requirements, the design and construction of the test articles placed inside PELICAN’s test section, and finally present some of the first experimental results.

Grannan, A. M.↗
NASA NTRS2000

Defect Characterization in a Thin Walled Composite RP-1 Tank: A Case Study

A full scale thin walled composite tank, designed and fabricated for the storage of pressurized RP- I rocket fuel, was fully inspected with digital infrared thermography (IR) during assembly and prior to proof testing. The tank featured a "pill capsule" design with the equatorial bondline being overwrapped on both the inner and outer surfaces. A composite skirt was bonded to the aft dome of the tank to serve as a structural support when the tank was stood on end in service. Numerous anomalies were detected and mapped prior to proof testing, some along bondlines and some scattered throughout the acreage. After the tank was intentionally burst, coupons were cut from the regions including thermographic anomalies. These coupons were again inspected thermographically to document the growth of any indications due to proof testing. Ultrasonic inspections (UT) were also performed on the coupons for comparison to thermography. Several coupons were dissected and micrographed. Relationships between IR and UT indications and the physical nature of the dissected material are presented.

Langsing, Matthew D.↗
DOE OSTI2023

MCNP Neutronic Design Optimization of an Accelerator-Driven Subcritical Assembly for Mo-99 Production

Molybdenum-99 (99Mo) has been in short supply in the recent decades. The most common productionmechanism, irradiation in a reactor fueled by highly enriched uranium (HEU), raisesproliferation concerns. Novel efforts are being pursued to meet the demand for 99Mo withoutHEU irradiation, relying on the processing of low-enriched uranium or natural uranium. Onesuch concept is to use an electron linear accelerator to generate bremsstrahlung that, through aphotonuclear reaction, can help multiply neutrons in a subcritical assembly. The goal of this workwas to neutronically optimize the subcritical assembly for keff and 99Mo production. This optimizationis unique for The design was optimized in terms of reflector type, pitch, and LEU andNU mass. Results of the paper show the effects of fuel mass, pitch, and reflector material on keffand the NU fission fraction. keff was found to be mostly driven by LEU mass, and the NU fissionfraction was dependent on several parameters, primarily pitch and mass.

Conant, Andrew↗
NASA NTRS1993

Viper cabin-fuselage structural design concept with engine installation and wing structural design

This report describes the process and considerations in designing the cabin, nose, drive shaft, and wing assemblies for the 'Viper' concept aircraft. Interfaces of these assemblies, as well as interfaces with the sections of the aircraft aft of the cabin, are also discussed. The results of the design process are included. The goal of this project is to provide a structural design which complies with FAR 23 requirements regarding occupant safety, emergency landing loads, and maneuvering loads. The design must also address the interfaces of the various systems in the cabin, nose, and wing, including the drive shaft, venting, vacuum, electrical, fuel, and control systems. Interfaces between the cabin assembly and the wing carrythrough and empennage assemblies were required, as well. In the design of the wing assemblies, consistency with the existing cabin design was required. The major areas considered in this report are materials and construction, loading, maintenance, environmental considerations, wing assembly fatigue, and weight. The first three areas are developed separately for the nose, cabin, drive shaft, and wing assemblies, while the last three are discussed for the entire design. For each assembly, loading calculations were performed to determine the proper sizing of major load carrying components. Table 1.0 lists the resulting margins of safety for these key components, along with the types of the loads involved, and the page number upon which they are discussed.

Marchesseault, B.↗
DOE OSTI2025

Design of a High-Assay Low-Enriched Uranium Tri-Structural Isotropic Critical Experiment for Advanced Reactor Validation

High-assay low-enriched uranium (HALEU) fuel is a key component of many small modular reactor designs. Critical experiments are an important way to understand the neutronic performance of systems by obtaining nuclear data validations through measurements. Data reduce uncertainty and risk by showing that systems respond as predicted to changes such as temperature, subsequently advancing the overall technology readiness level of the materials within. Numerous critical experiments have been performed at the National Criticality Experiments Research Center (NCERC) operated by Los Alamos National Laboratory at the Nevada National Security Site since it became operational in 2011. However, the first experiment with HALEU fuel did not occur until 2024. Through extensive engineering, the experiment described in this paper was successfully designed and executed for the Comet vertical lift assembly at NCERC to perform measurements with HALEU tri-structural isotropic fuel that will assist in validation of nuclear data and computational modeling of small modular reactors for years to come.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2003

Performance of WPA Conductivity Sensor during Two-Phase Fluid Flow in Microgravity

The Conductivity Sensor designed for use in the Node 3 Water Processor Assembly (WPA) was based on the existing Space Shuttle application for the fuel cell water system. However, engineering analysis has determined that this sensor design is potentially sensitive to two-phase fluid flow (gadliquid) in microgravity. The source for this sensitivity is the fact that gas bubbles will become lodged between the sensor probe and the wall of the housing without the aid of buoyancy in l-g. Once gas becomes lodged in the housing, the measured conductivity will be offset based on the volume of occluded gas. A development conductivity sensor was flown on the NASA Microgravity Plan to measure the offset, which was determined to range between 0 and 50%. Based on these findings, a development program was initiated at the sensor s manufacturer to develop a sensor design fully compatible with two-phase fluid flow in microgravity.

Carter, Layne↗
DOE OSTI2021

Neutronic Performance of a Compact 10 MWe Nuclear Reactor with Low Enrichment (ThxU1−x)N Fuel

Abstract Recent interest in compact nuclear reactors for applications in space or in remote locations drives innovation in nuclear fuel design, especially non-oxide ceramic nuclear fuels. This work details neutronic modeling designed to support the development of a new nuclear fuel concept based on a mixture of thorium and uranium nitride. A Monte Carlo N-Particle Version 6.2 (MCNP-6) model of a compact 10 MWe reactor design which incorporates (Th x U 1− x )N fuel is presented. In this context, a “compact” reactor is a completely assembled reactor which may be emptied of coolant and transported by specialized commercial vehicle, deployed by a C130J aircraft, or launched into space. Core geometry, reflector barrels, and the heat exchange zones are designed to support reduction of overall reactor volume of core components while maintaining criticality with a fixed total fuel mass of 4500 kg. Dense mixed nitrides of thorium nitride (ThN) additions in uranium nitride (UN) in 5 wt.% increments between $$0.05 \le x \le 0.5$$ 0.05 ≤ x ≤ 0.5 have been considered for calculation of $$k_{\infty }$$ k ∞ and $$k_{{{\text{effective}}}}$$ k effective . ThN additions in UN results in a slight increase in the magnitude of the temperature coefficient of reactivity, which is negative by design. The isotopic distribution of the principal actinide inventory as a function of burnup, time, and initial fuel composition is presented and discussed within the context of the proliferation risk of this core design.

Parker, S. S. (ORCID:000000018597440X)↗
DOE OSTI2022

Light Water Reactor LEU+ Lattice Optimization

Commercial light water reactor (LWR) operators and fuel vendors in the United States are exploring potential changes to nuclear fuel that include low-enriched uranium plus (LEU+) designs to further improve operational economics (e.g., extend cycle length). LEU+ fuel is fuel with a maximum enrichment between 5 wt% and 10 wt% 235 U; it allows for higher assembly burnup but likely requires additional reactivity control, e.g., increased burnable absorbers. This report examines possible LEU+ fuel lattice design changes using the lattice physics code, SCALE/Polaris. An optimization driver called the Metaheuristic Optimization Tool (MOT) is used to automate domain space exploration and optimization of LEU+ lattice designs. Heuristics from previous LWR lattice optimization studies were used to construct the objective function and define the domain space for optimization. This work successfully demonstrated that the optimization algorithms of MOT can generate feasible, nonproprietary LEU+ lattice designs (GE14 10 × 10 and Westinghouse 17 × 17) that meet the constraints of traditional LWR lattices while extending cycle length.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

3D-Printable Fluoropolymer Gas Diffusion Layers for CO 2 Electroreduction

The electrosynthesis of value-added multicarbon products from CO 2 is a promising strategy to shift chemical production away from fossil fuels. Particularly important is the rational design of gas diffusion electrode (GDE) assemblies to react selectively, at scale, and at high rates. However, the understanding of the gas diffusion layer (GDL) in these assemblies is limited for the CO 2 reduction reaction (CO 2 RR): particularly important, but incompletely understood, is how the GDL modulates product distributions of catalysts operating in high current density regimes > 300 mA cm -2 . Here, 3D-printable fluoropolymer GDLs with tunable microporosity and structure are reported and probe the effects of permeance, microstructural porosity, macrostructure, and surface morphology. Under a given choice of applied electrochemical potential and electrolyte, a 100× increase in the C 2 H 4 :CO ratio due to GDL surface morphology design over a homogeneously porous equivalent and a 1.8× increase in the C 2 H 4 partial current density due to a pyramidal macrostructure are observed. Overall, these findings offer routes to improve CO 2 RR GDEs as a platform for 3D catalyst design.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Design and analysis of a scramjet engine

Design concepts defined for the cooled-structures assembly of a hydrogen fueled, regeneratively cooled, airframe-integrated Scramjet engine are considered. Engine subsystems, in particular, the fuel subsystem associated with the operating engine are included along with the engine mounting and the interfacing with the airplane. The engine structure and thermal protection system, including the fuel injection struts are emphasized.

Buchmann, O. A.↗
DOE OSTI2020

Thermal Analysis Evaluations Using the Dry Cask Simulator

Different thermal analysis models were developed to simulate the dry cask simulator (DCS). The DCS is an experiment designed to simulate dry storage of a single boiling water reactor fuel assembly under a variety of heat loads and internal pressures. The DCS was set up and tested in both a vertical and horizontal configuration to determine cladding temperatures in vertical and horizontal dry cask storage systems. The models included a detailed STAR-CCM+ model with the fuel assembly geometry explicitly modeled, a porous STAR-CCM+ model with the fuel assembly geometry modeled as porous media region with calculated effective properties, and a COBRA-SFS model. COBRA-SFS is a thermal-hydraulic code developed for steady-state and transient analysis of multi assembly spent-fuel storage and transportation systems. STAR-CCM+ is a commercial computation fluid dynamics (CFD) code. Both a detailed and porous STARCCM+ model were developed to look at the effective thermal conductivity (keff) approach to modeling a fuel assembly. A keff fuel model is typically model in CFD thermal analyses due to its significantly lower computational costs. The models were run for a combination of low and high canister pressures (100 kPa and 800 kPa) and low and high internal heat loads (0.5 kW and 5 kW). Results from all three models were compared against experimental data taken from the DCS for the peak cladding temperature (PCT) and inlet air mass flow.

Suffield, Sarah R.↗
DOE OSTI2023

CFD Benchmark of Pressure Drop in a 61-Pin Wire-Wrapped Assembly with Blocked Channels Using NekRS

Thermal hydraulic behaviors of wire-wrapped rod bundles continue to be a subject of intense research. One of the leading next-generation designs, the sodium fast reactor, relies on a hexagonal assembly of wire-wrapped fuel pins. The issue of potential channel blockage has been raised as a safety concern due to the tightly packed arrangement of the fuel pins. This has led to several recent experimental and computational studies working to quantify the potential impact on the fluid flow and heat transfer behaviors of such blockages. The objective of the present study is to benchmark the high-fidelity NekRS CFD solver in predicting pressure drop for large blockages against available experimental data. A 61-pin wire-wrapped fuel assembly with two flow blockage configurations has been simulated and investigated at various low to moderate Reynolds numbers. The NekRS solver has been shown to yield exponentially decreasing spatial discretization errors with increasing polynomial order. All simulated results agreed well with measured data, which indicates that the overall methodology is adequate and consistent. The results of this benchmark study demonstrate the accuracy of NekRS for sodium fast reactor hydrodynamic simulations, increasing the confidence in its use for design, licensing, and analysis activities.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Full-Scale Assembly 30 cm Drop Test

Can Spent Nuclear Fuel withstand the shocks and vibrations experienced during normal conditions of transport? This question was the motivation for the multi-modal transportation test (MMTT) (Summer 2017), 1/3-scale cask 30 cm drop test (December 2018), and full-scale assembly 30 cm drop tests (June 2019). The full-scale ENSA ENUN 32P cask with 3 surrogate 17x17 PWR assemblies was used in the MMTT. The 1/3-scale cask was a mockup of this cask. The 30 cm drop tests provided the accelerations on the 1/3-scale dummy assemblies. These data were used to design full-scale assembly drop tests with the goal to quantify the strain fuel rods experience inside a cask when dropped from a height of 30 cm. The drop tests were first done with the dummy and then with the surrogate assembly. This paper presents the preliminary results of the tests.

Transportation↗
DOE OSTI2025

Conceptual Design of a Water Tank Critical Facility for SPARC

Critical experiments, sometimes referred to zero-power reactors, are crucial tools in developing and validating nuclear physics predictions and thus an indispensable capability to ensure criticality safety during all parts of the nuclear fuel cycle and in reducing uncertainties in reactor physics predictions toward optimizing nuclear energy production. The System Physics Advanced Reactor Facility (SPARC) project was recently initiated to enable large-scale criticality experiments using a horizontal split table machine well suited toward solid core materials systems (fuel, moderator, reflector). The facility selected for this mission was a former pool-type research reactor building and thus also well suited toward a second critical experiment capability able to house full-size light-water reactor (LWR) fuel bundles. A conceptual design study was undertaken to review past water tank critical experiments used for LWR physics experiments and to develop an early engineering design for a new critical assembly tank (CAT). The work described here shows that a relatively simple CAT concept can be constructed and deployed in the SPARC facility to meet the urgent demands for new critical experiments on advanced LWR fuel bundles designs. The SPARC facility layout is conducive to the receipt and upending of LWR fuel bundles using existing containers and equipment from the LWR industry. The facility’s overhead crane can then be used to handle fuel bundles and place them in a vertical storage rack or in the CAT for critical experiments, both of which fit within the building’s “open basement” alongside other equipment planned for SPARC and the horizontal split table. A slightly lower area in the basement can serve as a large drain tank so that fail-safe valves drain the CAT reactor tank for safe shutdown. Neutronic configurations were determined where a 3 × 3 array of fuel bundles can be surrounded by full-length “loose rods” to adjust reactivity so that critical is achieved when the bundles are fully submerged. Viable configurations were determined for both pressurized- and boiling-water-reactor-type fuel bundles. This design concept was used to develop an early planning basis for establishing the CAT capability alongside the otherwise planned SPARC project in order to help streamline the process. Recent presidential executive orders have highlighted the need to achieve power uprates in LWR plants and the CAT capability will be a crucial element of these initiatives. Based on the work described herein, it is recommended that an earnest and timely project begin in order to establish this urgently needed capability.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Pressurized Water Reactor Gadolinia Pin Location Optimization

This report presents the results of lattice optimization studies performed to find optimum locations for gadolinia burnable absorber (BA) rods in pressurized water reactor (PWR) lattice fuel designs. Initial excess reactivity suppression allows core designers to further improve operational economics by extending cycle length. Gadolinia BAs are commonly used in boiling water reactor assembly designs for this purpose. In recent years, gadolinia absorbers have been used in PWR designs owing to their longer effectiveness for reactivity suppression compared with common BAs used in PWR assemblies. This report examines the optimum gadolinia pin placement in 17 × 17 PWR lattices at different fuel and gadolinia concentrations for optimized lattice performance, using the SCALE/Polaris lattice physics code. The completed work is continuation of the Light Water Reactor LEU+ Lattice Optimization (ORNL/TM-2021/2366) project. An optimization driver called the metaheuristic optimization tool (MOT) is used to automate domain space exploration and optimization of the lattice designs. Heuristics from previous light-water reactor (LWR) lattice optimization studies were used to construct the objective function and define the domain space for optimization. This work successfully demonstrated that the optimization algorithms of MOT can generate feasible, nonproprietary PWR lattice designs with gadolinia.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1991

Heat transfer and core neutronics considerations of the heat pipe cooled thermionic reactor

The authors summarize the results of detailed neutronic and thermal-hydraulic evaluations of the heat pipe cooled thermionic (HPTI) reactor design, identify its key design attributes, and quantify its performance characteristics. The HPTI core uses modular, liquid-metal core heat transfer assemblies to replace the liquid-metal heat transport loop employed by in-core thermionic reactor designs of the past. The nuclear fuel, power conversion, heat transport, and heat rejection functions are all combined into a single modular unit. The reactor/converter assembly uses UN fuel pins to obtain a critical core configuration with in-core safety rods and reflector controls added to complete the subassembly. By thermally bonding the core heat transfer assemblies during the reactor core is coupled neutronically, thermally, and electrically into a modular assembly of individual power sources with cross-tied architecture. A forward-facing heat pipe radiator assembly extends from the reactor head in the shape of a frustum of a cone on the opposite side of the power system from the payload. Important virtues of the concept are the absence of any single-point failures and the ability of the core to effectively transfer the TFE waste heat load laterally to other in-core heat transfer assemblies in the event of multiple failures in either in-core and radiator heat pipes.

Determan, W. R.↗
DOE OSTI2021

Isotopic and Fuel Lattice Parameter Trends in Extended Enrichment and Higher Burnup LWR Fuel, Volume II: BWR

Commercial light water reactor (LWR) operators and fuel vendors in the United States are pursuing changes to nuclear fuel that include extended enrichment (EE) and accident-tolerant fuel (ATF) designs to further improve reactor safety and plant economics. Extended fuel enrichments above 5% 235 U pin enrichment and up to 10% 235 U are a subset of high assay low-enriched uranium (HALEU) that may be deployed in commercial US LWRs in the near term. ATF features, such as cladding coatings or alternative cladding materials, are designed to improve fuel system performance under accident conditions. One goal of EE is to improve fuel cycle economy by enabling fuel to be depleted to higher burnup than the typical current limits (62 gigawatt-days per metric ton of uranium [GWd/MTU]). Adoption of EE, ATF, and high burnup (HBU) fuels in the US commercial fleet requires a clear understanding of the effects on core physics parameters and used fuel isotopic content, as well as confidence in the accuracy of computer code predictions over an expanded range of materials, enrichment, and burnup. A thorough understanding of the applicability and adequacy of benchmark data (e.g., criticality, decay heat, isotopic content) for computer code validation is necessary to ensure that appropriate safety margins are maintained. As part of the US Nuclear Regulatory Commission (NRC) agreement number 31310019N0008, “SCALE Code Development, Assessment and Maintenance,” the effects of EE, ATF, and HBU are being assessed for selected representative LWR fuel designs. The project is divided into phases, and this report summarizes the findings of the Phase 1 work, which focuses on lattice physics parameter and used fuel isotopic changes for a conventional GE14 10 x 10 boiling water reactor (BWR) design with GNF-2 part length rod patterns to model a modern BWR assembly design.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

PELICAN Status Report for Year 2021

The Pressure Drop Experimental Loop for Investigations of Core Assemblies in Advanced Nuclear Reactors, PELICAN, is a novel experimental facility designed and constructed to recreate the prototypic full scale hydraulic flow conditions for the Versatile Test Reactor (VTR) currently under development by the U.S. Department of Energy. To support VTR design efforts, PELICAN is used to replicate VTR’s primary heat transport system (PHTS) in the core assembly region. The measurement objectives for data generated from this test facility are to mimic the prototypic VTR assembly and to meet the validation needs for code calculations and simulations of the reference design for the VTR core. These objectives focus on the need to validate pressure drop results across the various segments of the fuel assembly, including the axial reflectors, fuel, and transition regions, as they relate directly to the pumping power and safety behavior of the reactor. In the following sections, the major milestones for the experimental work performed on PELICAN over the calendar year (CY) 2021 are presented. In the next section, we discuss the assembly and shakedown testing of the facility. In Section 3, an analysis of the errors in the major measurements is performed. In Section 4 and 5 we present the results from the first set of test articles placed inside the loop. The design of the remaining test articles as part of the full assembly are shown in Section 6 and the conclusion and path forward for the following year, CY22 is given in the final section.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗