Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Effects of multifunctional crosslinking agents on the thermomechanical properties of polyimide films

The potential of high temperature resistant polymers such as polyimides (PI) and polyphenylquinoxalines (PPQ) as matrix resins in fiber-reinforced composites has not been fully realized to date. One of the problems associated with these resins is that they exhibit creep, or thermoplastic yielding under load at temperatures approaching 316 C (600 F). The purpose of this investigation was to further reduce thermoplastic behavior of polyimide resins by substituting a controlled amount of the diamine monomer with crosslinking agents having a higher amine functionality. The knowledge gained from a study of the thermomechanical properties of the crosslinked resins would then be used in the fabrication of fiber-reinforced polyimide composites. This report describes the synthesis and characterization of three new polyfunctional amines. Polyimide films containing varying amounts of the cross-linking agents were prepared, and their properties compared with those of control samples prepared with difunctional amines. The effect of crosslink density on isothermal weight loss, polymer softening, and glass transition temperatures is discussed.

Delvigs, P.↗

Composite impact strength improvement through a fiber/matrix interphase

Research was conducted to improve the impact strength and toughness of fiber/resin composites by means of a fiber coating interphase. Graphite fiber/epoxy resin composites were fabricated with four different fiber coating systems introduced in a matrix-fiber interphase. Two graphite fibers, a high strength and a high modulus type, were studied with the following coating systems: chemical vapor deposited boron, electroless nickel, a polyamide-imide resin and a thermoplastic polysulfone resin. Evaluation methods included the following tests: Izod, flexure, shear fracture toughness, longitudinal and transverse tensile, and transverse and longitudinal compression. No desirable changes could be effected with the high strength fiber, but significant improvements in impact performance were observed with the polyamide-imide resin coated high modulus fiber with no loss in composite modulus.

Cavano, P. J.↗

Contamination control in hybrid microelectronic modules. Part 3: Specifications for coating material and process controls

Resin systems for coating hybrids prior to hermetic sealing are described. The resin systems are a flexible silicone junction resin system and a flexible cycloaliphatic epoxy resin system. The coatings are intended for application to the hybrid after all the chips have been assembled and wire bonded, but prior to hermetic sealing of the package. The purpose of the coating is to control particulate contamination by immobilizing particles and by passivating the hybrid. Recommended process controls for the purpose of minimizing contamination in hybrid microcircuit packages are given. Emphasis is placed on those critical hybrid processing steps in which contamination is most likely to occur.

Himmel, R. P.↗

Diterpenoid compounds and other lipids in deep-sea sediments and their geochemical significance

Cyclic diterpenoid compounds have been found by various investigators in the geosphere (e.g., fossil resins, coals, soil, shale, and deep-sea sediments). These compounds occur in significant amounts only in higher plants and are therefore potential markers of terrigenous plant lipids. Diterpenoids with the abietane skeleton (mainly dehydroabietic acid) have been identified in the lipids of sediment samples from the northeast Pacific Ocean, Black Sea, and North Atlantic Ocean. The presence of these resin-derived compounds was correlated with the terrigenous clay components and with the presence of pollen. The presence of polycyclic diterpenoids was also correlated with the distribution patterns and inferred sources of other sediment lipid constituents. Potamic transport, followed by turbidite redistribution, is the probable input mechanism of these resin-derived compounds to the deep-sea sediments. These diterpenoids appear to be excellent biological markers of resinous higher plants.

Simoneit, B. R. T.↗

ALC/50/ values for some polymeric materials

Apparent lethal concentrations for 50 per cent of the test animals within a 30-min exposure period (ALC/50/) were determined for seventeen samples of polymeric materials, using the screening test method. The materials evaluated included resin-glass composites, film composites, and miscellaneous resins. ALC(50) values, based on weight of original sample charged, ranged from 24 to 110 mg/l. Modified phenolic resins seemed to exhibit less toxicity than the baseline epoxy resins. Among the film composites evaluated, only flame modified polyvinyl fluoride appeared to exhibit less toxicity than the baseline polyvinyl fluoride film.

Hilado, C. J.↗

New High Temperature Cross Linking Monomers

This report describes the results of a one-year program designed to synthesize new, nonvolatile crosslinking monomers and to prove their feasibility in the development of lower temperature curing PMR-polyimide resins with high temperature capability. The objective of this program is to develop PMR-polyimide resins capable of being processed at a maximum temperature of 232C to 288C (450F to 500F) without sacrifice of the high temperature 316C (600F) capability of the state-of-the-art PMR-15 polyimide resin. Four monomethyl esters were synthesized and characterized for use in the crosslinking studies. It was found that all four crosslinkers were capable of entering into a crosslinking reaction to produce polymer specimens which were strong, dense and free of voids. The infrared and DSC studies of each crosslinker with monomers 4,4'-methylenedianiline (MDA) and the dimethyl ester of 3,3',4,4'-benzophenonetetracarboxylic acid (BTDE) comprising the resin systems, crosslinker/MDA/BTDE suggested that curing could be accomplished at 288C (550F). However, fabrication of dense, void free polymer specimens required a temperature of 316C (600F) and a pressure of 0.69 MPa (100 psi). The crosslinkers, monomethyl ester of 2,5-bicyclo[2.2.1]heptadiene-2,3-dicarboxylic acid (NDE) and monomethyl ester of maleic acid (MAE) were selected for evaluation in Celion 6000/PMR polyimide composites. These composites were characterized at RT, 288C (550F) and 316C (600F) initially and after isothermal aging at 288C (550F) and 316C (600F) for several hundred hours. The results of the isothermal aging studies suggested that both PMR systems NDE-MDA-BTDE and MAE-MDA-BTDE are promising candidates as matrices for addition type polyimide composites. These studies demonstrated that alternate crosslinkers to NE/MDA/BTDE are feasible, but mechanisms to lower the crosslinking temperature must be developed to provide lower temperature processing PMR-type polyimides.

Scola, Daniel A.↗

Thermal response of composite panels

The thermochemical and flammability characteristics of laminating resins and composites currently in use and others being considered for use as aircraft interior panels are described. The properties studied included: (1) limiting oxygen index of the composite constituents; (2) fire containment capability of the composite; (3) smoke evolution from the composite; (4) thermogravimetric analysis; (5) composition of the volatile products of thermal degradation; and (6) relative toxicity of the volatile products of pyrolysis. The performance of high-temperature laminating resins such as modified phenolics, polyimides and bismaleimides is compared with the performance of epoxies. The relationship of increased fire safety with the use of polymers with high anaerobic char yield is shown. Processing parameters of the state-of-the-art epoxy resin and the advanced resin composites are detailed.

Kourtides, D. A.↗

Burning characteristics and fiber retention of graphite/resin matrix composites

Graphite fiber reinforced resin matrix composites were subjected to controlled burning conditions to determine their burning characteristics and fiber retention properties. Two types of burning equipment were used. Small samples were burned with a natural gas fired torch to study the effects of fiber orientation and structural flaws such as holes and slits that were machined into the laminates. Larger laminate samples were burned in a Heat Release Rate Calorimeter. Unidirectional epoxy/graphite and polyimide/graphite composites and boron powder filled samples of each of the two composite systems were burn tested and exposed to a thermal radiation. The effects of fiber orientation, flaws, and boron filler additives to the resins were evaluated. A high char forming polyimide resin was no more effective in retaining graphite fibers than a low char forming epoxy resin when burning in air.

Bowles, K. J.↗

Lower-curing-temperature PMR polyimides

Studies were performed to achieve a lower-curing-temperature PMR polyimide. The use of m-aminostyrene as the end-cap instead of the monoalkyl ester of 5-normbornene-2,3 dicarboxylic acid was investigated in typical PMR formulations. Model compound studies were also performed. Differential scanning calorimetry studies were performed on model compounds and neat resins to establish their melting and curing characteristics. The elevated temperature weight loss characteristics of neat resins and graphite fiber composites were determined. The room temperature and short-time 260 C (500 F) mechanical properties of the composites were also determined. The use of m-aminostyrene end-caps reduced the final cure temperature of PMR resins by about 55 C (100 F), but the composites prepared with these resins are limited to use temperatures of about 260 C (500 F).

Serafini, T. T.↗

Characterization of aging effects of LARC-160

Specimens of freshly prepared polyimide precursor resin LARC-160 and resin aged at room temperature up to 45 days were characterized by high-pressure liquid chromatography and several different thermal analyses. Graphite reinforced composites were then fabricated from fresh and aged resin and tested to determine if changes observed by these techniques were significant. It was found that resin aging resulted in greater flow during processing and poorer composite isothermal stability. However, aging did not affect the room-temperature flexural or short-beam-shear strengths of the composites.

Young, P. R.↗

Novel improved PMR polyimides

A series of N-phenylnadimide (PN) modified PMR polyimide composites reinforced with graphite fibers was investigated. The improved flow matrix resins consist of N-phenylnadimide (PN), monomenthyl ester of 5-norbornene-2, 3-dicarboxylic acid (NE), dimethyl ester of 3,3, 4,4-benzophenonetetracarboxylic acide (BTDE), and 4,4 methylenedianiline (MDA). Five modified PMR resin systems were formulated by the addition of 4 to 20 mole percent N-phenylnadimide to the standard PMR-15 composition. These formulations and the control PMR resin were evaluated for rheological characteristics. The initial thermal and mechanical properties of the PN modified PMR and the control PMR/Celion 6000 composites were determined. The results show that the addition of N-phenylnadimide to PMR-15 significantly improved the resin flow characteristics without sacrificing the composites properties. Concentrations of 4 and 9 mole percent PN appear to improve the thermoxidative stability of PMR composites.

Pater, R. H.↗

Nonequilibrium material effects on the behavior of polymeric composite matrices and their related composites

The effects of physical aging on the material properties of some linear and network macromolecular glasses are discussed. The free volume concept is used to describe this behavior. The effect of physical aging on properties of some uniaxial graphite/fiber epoxy resin composites is investigated using stress relaxation in both tensile and flexural modes. The matrix polymers used were resins both of which are based on a 4,4-methylenedianiline derivative of epichlorohydrin with diamino diphenyl sulfone (DDS) as the curing agent. The matrix resin, as used in the practical application in composites, not fully cured and the glass transition of the network was dependent on the curing schedule. The physical aging of the bulk crosslinked epoxy was found to depend on the annealing temperature, and the T sub g of the resin. The physical aging of the composite, monitored by the stress relaxation method, was found to be dependent on the testing direction.

Wilkes, G. L.↗

Novel improved PMR polyimides

The development of a class of high-temperature-resistant resins known as PMR polyimides has been reported by Serafini et al. (1972). Serafini and Vannucci (1975) found that the lower formulated molecular weight (FMW) compositions exhibited increased resin flow, but with some sacrifice in elevated temperature thermo-oxidative stability. Vannucci (1977) reported that the resin flow characteristics of the PMR composition having an FMW of 1500 could be varied by controlling the degree of resin advancement or imidization. The current investigation is concerned with an alternative approach to obtain improved flow PMR polyimides without sacrificing the desirable thermo-oxidative characteristics. The new approach is based on the utilization of a chemically compatible flow modifying agent. This agent is N-phenylnadimide (PN). The determination of the processing characteristics and properties of PN modified PMR/Celion 6000 composites is discussed.

Pater, R. H.↗

Development of phosphorylated adhesives

The synthesis of epoxy prepolymers containing phosphorus was carried out in such a manner as to provide adhesives containing at least 5 percent of this element. The purpose of this was to impart fire retardant properties to the adhesive. The two epoxy derivatives, bis(4-glycidyl-oxyphenyl)phenylphosphine oxide and bis(4-glycidyl-2-methoxyphenyl)phenylphosphonate, and a curing agent, bis(3-aminophenyl)methylphosphine oxide, were used in conjunction with one another and along with conventional epoxy resins and curing agents to bond Tedlar and Polyphenylethersulfone films to Kerimid-glass syntactic foam-filled honeycomb structures. Elevated temperatures are required to cure the epoxy resins with the phosphorus-contaning diamine; however, when Tedlar is being bonded, lower curing temperatures must be used to avoid shrinkage and the concomitant formation of surface defects. Thus, the phosphorus-containing aromatic amine curing agent cannot be used alone, although it is possible to use it in conjunction with an aliphatic amine which would allow lower cure temperatures to be used. The experimental epoxy resins have not provided adhesive bonds quite as strong as those provided by Epon 828 when compared in peel tests, but the differences are not very significant. It should be noted, if optimum properties are to be realized. In any case the fire retardant characteristics of the neat resin systems obtained are quite pronounced, since in most cases the self-extinguishing properties are evident almost instantly when specimens are removed from a flame.

Bilow, N.↗

Modifying a silicone potting compound for space flight applications

RTV-615 has been devolatilized by subjecting the uncatalyzed resin to a temperature of between 125 and 150 C for 24 hours in a vacuum of about 10 to the -6th torr. The resultant resin can be catalyzed and after a room temperature cure the outgassing of the resin is sufficiently low when tested according to ASTM E-595 that it is suitable for space flight use. Tests of physical properties of the cured devolatilized resin were compared with those of the as received silicone. The devolatilized silicones are slightly harder, have a higher tear resistance and higher tensile strengths.

Park, J. J.↗

Silicon carbide-silicon nitride fibers: Preparation and characterization of polycarbosilazane precursors

This study examines the effect of modifications of the chemical structure of the monomers on the properties of the polymeric precursor and and ceramic fibers. A group of silaneamines, R'-Si (NH-R) sub 3, taken from the series where R' is methyl or phenyl and R is n-propyl, n-butyl, phenyl or allyl, are converted to polycarbosilazanes by heating in excess of 500 C. Resins obtained from this polymerization are characterized by NMR and IR spectroscopy and GPC. Each resin is tested for fiber-forming properties. Resin samples and fibers are hydrolytically cured. Thermogravimetric analyses are conducted on the cured resins to compare the relative thermal stability and examine the pyrolysis process. Cured fibers are tested for tensil strength.

Crouse, D. J.↗

Evaluation of experimental epoxy monomers

Future generation aircraft need higher performance polymer matrices to fully achieve the weight savings possible with composite materials. New resins are being formulated in an effort to understand basic polymer behavior and to develop improved resins. Some polymer/curing agent combinations that could be useful are difficult to process. In the area of epoxies, a major problem is that some components have physical properties which make them difficult to utilize as matrix resins. A previous study showed that the use of ultrasonic energy can be advantageous in the mixing of curing agents into a standard epoxy resin, such as MY 720 (Ciba-Geigy designation). This work is expanded to include three novel epoxides.

Hodges, W. T.↗

Measurements of the response of transport aircraft ceiling panels to fuel pool fires

Tests were performed to characterize the responses of various aircraft ceiling panel configurations to a simulated post-crash fire. Attention was given to one currently used and four new ceiling configurations exposed to a fuel pool fire in a circulated air enclosure. The tests were controlled to accurately represent conditions in a real fire. The panels were constructed of fiberglass-epoxy, graphite-phenolic resin, fiberglass-phenolic resin, Kevlar-epoxy, and Kevlar-phenolic resin materials. The phenolic resin-backed sheets performed the best under the circumstances, except when combined with Kevlar, which became porous when charred.

Bankston, C. P.↗