Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “routing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Aqueous ionic liquid–mediated depolymerization of textile waste

Textile waste, dominated by polyester-cotton blends, largely evades recycling and ends up in landfills or incinerators. Here, we demonstrate an aqueous ionic liquid–mediated route for selective depolymerization of textile waste, including polyester and polycotton (polyester/cotton blend). Using aqueous cholinium lysinate ([Ch][Lys]), we depolymerized poly(ethylene terephthalate) (PET) textiles with over 95 % terephthalic acid (TPA) yields, comparable to virgin PET resin. Notably, colored fabrics showed no inhibitory effect from dyes. While protic ionic liquids such as ethanolammonium acetate showed limited efficiency, their precursor amine enabled near-complete PET conversion—ethanolamine promoted aminolysis with byproduct formation whereas butylamine achieved higher TPA recovery through combined hydrolysis and aminolysis. Importantly, polycotton blends achieved complete PET depolymerization with TPA yield above 85 % and preserved cotton. These results establish aqueous ionic liquids as efficient, selective agents for deconstructing polyester in blended textiles, offering flexible product and ionic liquid management pathways toward scalable and facile textile recycling.

Amines↗
DOE OSTI2020

Manufacturing Process Design of a Micro-Scale Liquid-Liquid Extractor and Multi-phase Separator

Advances in process innovation within the chemical process industry are impeded by the cost of producing new innovative components. In this paper, various manufacturing process routes were evaluated for scaling up a micro-scale liquid-liquid extractor and multi-phase separator capable of separating immiscible phases that are used for the extraction of a chemical product into a lower boiling point solvent to make downstream distillation easier. A manufacturing process design methodology was used to evaluate both photochemical machining and binder jetting as a means for producing the micropost arrays within the separator. Cost curves show that for a 0.3 mm deep micropost array, photochemical machining was found to be much cheaper than binder jetting. However, because binder jetting processes enable microposts with over 13 times higher depth-to-width aspect ratios, binder jetting was found to decrease the overall costs of the extractor/separator by more than half for a 500 barrel per day plant, with breakeven as low as 15 barrels per day. These economics were confirmed by building extractor/separator plates and characterizing them dimensionally and functionally. The binder jet plates were found to perform better than photochemical plates leading to the complete separation of the organic phase from water. The utilization of slower sintering cycles combined with surface grinding provided acceptable dimensional tolerances for the binder jet plates. Using pressurized air during depowdering improved the economics for the binder jetting process.

42 ENGINEERING↗
DOE OSTI2026

Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism

Fabricating integrated aluminum-steel structures is difficult because of metallurgical incompatibilities that promote intermetallic compound (IMC) formation at their interfaces. This work introduces a practical route for additively manufacturing 6061-T6 aluminum alloy (AA6061-T6) directly onto 304 stainless steel (SS304) using a high shear strain rate-assisted interfacial bonding mechanism. Through the friction extrusion deposition-based additive manufacturing method, both single- and multi-layer deposits of AA6061-T6 were successfully fabricated on SS304, yielding a robust hybrid multi-material structure. Comprehensive analyses of deposition quality, interface porosity, and bonding performance showed that the interface achieved a tensile strength exceeding 154 MPa under quasi-static loading. Microstructural observations revealed that the deposited aluminum layers experienced severe plastic deformation, resulting in pronounced grain refinement. Importantly, the interfacial zone was found to be free of brittle IMCs, instead containing a thin amorphous layer that evolved through a non-linear reaction-zone growth law. This solid-state additive strategy establishes a promising pathway for lightweight structural systems, nuclear energy component cladding, and multifunctional engineering components, redefining how dissimilar metals can be integrated for advanced applications.

Aluminum alloy↗
DOE OSTI2026

From high-entropy ceramics to compositionally complex ceramics and beyond

Over the past decade, the field of high-entropy ceramics (HECs) has expanded rapidly to encompass a broad range of oxides, borides, silicides, and other ceramic solid solutions. In 2020, we proposed extending HECs to compositionally complex ceramics (CCCs), where non-equimolar compositions and the presence of long- or short-range order, although reducing configurational entropy, create new opportunities to tailor and enhance properties, often surpassing those of higher-entropy counterparts. Along these lines, several fundamental scientific questions arise. Is the entropy in HECs truly high? Is maximizing entropy always desirable? In this perspective article, I revisit key concepts and terminologies and highlight emerging directions, including dual-phase CCCs, ultrahigh-entropy phases, and novel processing routes such as ultrafast reactive sintering. I propose that exploring compositional complexity across vast non-equimolar spaces, together with exploiting correlated disorder (coupled chemical and structural short-range order), represents a transformative strategy for designing ceramics with superior performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhanced biomechanical performance of additively manufactured Ti-6Al-4V bone plates

As the global trauma fixation devices market expands rapidly, it is imperative to improve the production of fixation devices through enhanced design accuracy and fit for best performance and maximum patient comfort. Selective laser melting (SLM) is one of the mature additive manufacturing methods, which provides a viable route for the rapid production of such devices. In this work, the ability of SLM to produce near-net-shape parts, as desired for medical implants, was utilized for the fabrication of bone plates from Ti-6Al-4V alloy powder. Martensitic microstructure obtained after the printing of alloy resulted in poor ductility, limiting its application in the field of orthopedics. A specially designed repeated cyclic heating and cooling close to but below the β-transus was used to transform from acicular to a bimodal microstructure without the need for plastic deformation prior to heat treatment for improving the ductility. Bone plates subjected to this heat treatment were mechanically tested by means of tensile and 3-point bend tests and demonstrated large improvement in ductility, and the values were comparable to those similar plates prepared from wrought alloy. Other important properties required for implants were assessed, such as corrosion resistance in simulated body fluid and cytocompatibility in vitro using MC3T3-E1 cells. These results for the bone plate after heat treatment were excellent and similar to those of the additively manufactured and wrought plates. Taken together, the performance of the additively manufactured bone plates after subjecting to heat treatment was similar to those of bone plate manufactured using wrought alloy. These results have important implications for the fabrication of patient-specific metallic orthopedic devices using SLM without compromising their biomechanical performance by subjecting them to a tailored heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Decoupling the effects of texture and composition on magnetic properties of Fe-Si sheet processed by shear deformation

Soft magnetic Fe-Si alloys (electrical steels) possess exceptional functional properties such as high permeability, low coercivity, and low core loss, which generally improve with increasing Si content in the alloy. However, Fe-Si alloys containing > 3.5 wt% Si are also characterized by prohibitively low workability and poor ductility that have prevented their efficient commercial production in sheet form by rolling. This has limited their use for improving efficiency of motors and transformers. In this study, hybrid cutting-extrusion (HCE) is used as a single-step thermomechanical processing method to produce continuous Fe-Si alloy sheet with high Si compositions of 4 wt% to 6.5 wt%. HCE sheet is shown to have a homogeneous annealed grain structure and simple-shear crystallographic textures. By controlling the HCE deformation path, varied crystallographic shear textures are created in the sheet. Quasi-static magnetic properties of the HCE sheet are evaluated to decouple the effects of sheet texture and Si composition on resultant permeability and coercivity properties. The results suggest that HCE, with suitable process scaling, is a viable route for production of high-Si content electrical steel sheet for next-generation motors and transformers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling Ti–6Al–4V using crystal plasticity, calibrated with multi-scale experiments, to understand the effect of the orientation and morphology of the α and β phases on time dependent cyclic loading

Classically, crystal plasticity modeling has used a range of constitutive equations, in which the incorporation of additional physics-based relationships typically results in additional model parameters. These additional parameters need to be reliably calibrated, which often necessitates the use of a range of experimental data acquired at multiple length scales. In this work, a crystal plasticity based finite element (CPFE) model for a dual-phase Titanium alloy, Ti–6Al–4V, is developed. The α and β phases of the microstructure are explicitly modeled. The model is calibrated using a systematic optimization routine and experimental data that consist of macroscopic stress-strain curves coupled with lattice strains on different crystallographic planes for the two phases. These experimental data were obtained from in situ high energy X-ray diffraction experiments for multiple material pedigrees, with varying crystallographic orientation distribution and β volume fractions. Depending on the thermomechanical-processing route and the heat treatment used to manufacture the alloy, Ti–6Al–4V can exist in a wide number of microstructural forms, which often results in the α and β phases either having well aligned slip systems (following the Burgers orientation relationship (BOR)) or possessing no alignment of the slip systems across the interphase boundary (not following the BOR). In this study, the fully-calibrated CPFE model is used to gain a comprehensive understanding of the deformation behavior of Ti–6Al–4V, specifically, the effect of microstructures that follow the BOR (or not) on time-dependent cyclic loading (including the effects of dwell hold times).

36 MATERIALS SCIENCE↗
DOE OSTI2026

Binder-jetted AISI M2 tool steel during hot isostatic pressing: Densification and carbide transformation

Binder jetting (BJ) enables fabrication of complex components from high-alloy steels such as AISI M2; however, residual porosity after sintering limits mechanical performance. This study investigates the coupled effects of binder chemistry, sintering conditions, cooling rate, and subsequent hot isostatic pressing (HIP) on densification, microstructure, and mechanical response in binder-jetted M2 tool steel. HIP increased relative density from ∼93 to 95% to >99% and improved compressive strength by ∼40-70%. Densification was governed by initial pore morphology, where closed porosity was effectively eliminated, while interconnected porosity limited full consolidation. Microstructural analysis (XRD, EBSD, SEM) shows that HIP promotes dissolution of metastable carbides and redistribution of alloying elements (W, Mo, V), transforming heterogeneous carbide networks into finer and more uniformly distributed M 2 C, MC, and M 6 C phases through diffusion-assisted homogenization. Among the investigated conditions, the FluidFuse binder combined with sintering at 1270 °C for 60 min and furnace cooling produced the most balanced response, achieving ∼99.7% density, ∼855 HV hardness, ∼4130 MPa compressive strength, and ∼24% strain. In contrast, higher sintering temperatures promoted carbide coarsening, reducing ductility despite high density. HIP reduces microstructural heterogeneity and drives the system toward a near-equilibrium state with reduced sensitivity to prior processing history. A comparative assessment with conventional and additive manufacturing routes (LPBF, DED, EBM, FFF) shows that the BJ-HIP approach achieves competitive densification and mechanical performance. These findings provide a mechanistic basis for controlling densification and microstructure in high-alloy steels processed via BJAM.

AISI M2 tool steel↗
DOE OSTI2020

Microstructure and fracture toughness characterization of three 9Cr ODS EUROFER steels with different thermo-mechanical treatments

Ferritic martensitic ODS steels are one of the candidate structural materials for future Gen-IV nuclear fission and fusion reactors. Here, the dependence of fracture toughness on microstructure was investigated by comparing three 9Cr ODS EUROFER steels manufactured through different thermo-mechanical processing routes. Quasi-static fracture toughness testing was performed with sub-sized C(T) specimens and microstructural characterization was carried out using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy. It was found that at lower test temperatures (-100 – 22 °C), the fracture toughness was primarily controlled by crack initiation at sub-micron particles and by production of secondary cracks during fracture. At higher temperatures (above 100 °C), fracture toughness was predominantly controlled by the matrix ductility and the grain boundary strength with a relatively ductile coarse-grained alloy demonstrating higher fracture toughness compared to high-strength fine-grained alloys. These results and discussion show that variations in thermomechanical treatments can produce significant differences in microstructure and fracture toughness behavior of ferritic martensitic ODS steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

α-U and ω-UZr 2 in neutron irradiated U-10Zr annular metallic fuel

Here, to develop metallic fuel with ultra-high burnup of 30%-40%, an annular U-10Zr fuel with 55% smear density was fabricated through a casting route and irradiated at the Advanced Test Reactor at Idaho National Laboratory. The annular fuel design also serves as a demonstration of the feasibility to replace sodium bond with a helium bond to benefit the geological disposal of irradiated fuel, cut the cost of fuel fabrication, and boost the overall metallic fuel economy. This paper reports the results from transmission electron microscopy (TEM) based post-irradiation examination of this fuel type irradiated to a burnup of 3.3% fissions per initial heave metal atoms for initial screening purpose. After irradiation, the initial U-10Zr separated into an a-U annular region and an UZr 2+x center region with nanoscale spinodal decomposed microstructure. Because of the provided large amount of coherent interface areas, the fission gas atoms and vacancies generated in UZr 2+x phase are possibly pinned at the interface areas, leading to 20 times smaller fission gas bubbles than those in the neighboring a-U. The large bubbles in a-U become connected and merged into large pores that provide fast release paths for fission gas which prevents further fuel swelling. The fuel center still has open space to accommodate further fuel swelling from solid fission products at higher burnup. Other neutron irradiation induced phase and microstructure change are also characterized and compared with traditional solid fuel designs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of PyC/SiC interfaces with FIB-SEM tomography

Tristructural-isotropic (TRISO) fuel is being considered for multiple reactor designs due to its exceptional performance. This work studies pyrocarbon (PyC) and silicon carbide (SiC) substrates that are near-representative of the inner pyrocarbon (IPyC) and SiC in TRISO fuel. Focused ion beam (FIB)-scanning electron microscopy (SEM) tomography was used to understand the influence of different processing routes on the PyC/SiC interface structure. Additionally, this work outlines a methodology for characterizing the IPyC/SiC interface when considering fission product accommodation and retention in TRISO fuel design. The high-fidelity images collected with FIB-SEM tomography can be used to achieve a more in-depth interpretation of microstructural parameters and pore-shape analysis that can inform simulations and processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Uranium Oxide Synthetic Pathway Discernment through Unsupervised Morphological Analysis

We present a novel unsupervised machine learning method for quantitative representation of scanning electron micrographs and its applications and performance for nuclear forensic analysis of uranium ore concentrates. The method uses a vector quantizing variational autoencoder followed by a histogram operation to encode a micrograph into a single dimensional representation, called the latent vector. The method requires no extant labeling of the data and can be applied over large datasets of micrographs with minimal human interaction. The representations generated are broadly descriptive of each micrograph and the microstructure of the material imaged. In the case of uranium ore concentrate analysis, the representations were amenable to processing reagent and ore concentrate species classification with accuracy of 81:8%, which is competitive with state-of-the-art supervised networks. The representations were also used to classify previously unseen processing routes, were able to classify imaging parameters such as magnification (to 76:0% accuracy), were able to classify fine grained process parameters such as calcining temperature (to 74:4% accuracy), and their informatic properties indicate that they are generally descriptive of the image represented. This method can be applied across microstructure analysis fields to perform quantitative analysis without the need for labor intensive and possibly biased human analysis.

Scanning Electron Microscopy, Vector Quantizing Va↗
DOE OSTI2022

Investigating the stability of reoriented hydrides and their reprecipitation using in-situ heating experiments

The behavior of radial hydrides in Zr-2.5Nb pressure tube samples at elevated temperature has been studied. The aim of this work is to investigate the stability of stress-reoriented hydrides under heating without an external applied load. Using in-situ heating at beamline, 1-ID at Argonne National Laboratory, USA, it was shown that two populations of hydrides existed in the sample, naturally oriented and reoriented hydrides. At a relatively low temperature of 180 °C it was observed that the reoriented hydrides completely dissolved, leaving only the naturally oriented hydrides in the sample, when heated without an applied load. On subsequent cooling of the sample, only naturally oriented hydrides were observed. These observations were confirmed using in-situ scanning electron microscopy heating experiments and post-mortem transmission electron microscopy studies. The results presented here offer a potential route for ductility recovery of pressure tube materials where radial hydrides have been shown to significantly reduce fracture toughness of components.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impacts of annealing treatment on the microstructure of U-Mo monolithic fuel plates

The objective of this paper is to analyze the effect of different heat treatments on the fuel microstructure and texture in laboratory scale monolithic U-Mo fuel plates. Such analyses are relevant as they could possibly inform future fabrication methods for the optimization of microstructure and of material properties to ultimately improve fuel performance during irradiation. For this reason, detail characterization including Energy x-ray dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) techniques were applied on U-Mo plates fabricated with different heat treatments to understand the influence of fabrication on fuel microstructure. Here, U-Mo fresh fuel specimens with or without annealing treatments (homogenization and stress release annealing) after rolling were analyzed in this work. In this study for the first time EBSD was systematically used to analyze the heat treatments influence on texture present in fresh fuel monolithic U-Mo fuel plates. Such changes were connected to other known microstructural and chemical changes. In this work minimization of molybdenum concentration variation and gamma phase decomposition of the U-Mo fuel core after homogenization was observed. Also, an increase in the interaction layer of the U-Mo fuel core with the Zr interlayer diffusion barrier was observed with the UZr 2 growing up to 1 µm in thickness. Such microstructural changes were aligned to the changes in texture and grain structure. Indeed, common texture observed in body-centered cubic (BCC) metal after cold rolling (e.g., α, ξ, γ fibers) were minimized by the annealing/homogenization process. Moreover, grain structure was influenced by the fabrication route with elongated grains formed in the rolled sample and equiaxed grains found after annealing. Such features are relevant since the formation of microstructural features formed during fuel fabrication can impact fuel performance in reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Microstructure and phase evolution in the U-10Zr fuel investigated by in situ TEM heating experiments

The development of U-Zr metallic nuclear fuel for fast spectrum reactors is impacted by a lack of mechanistic understanding of the fuel behavior evolution under thermal irradiation conditions, despite previous works providing substantial fuel performance data. This work uses in-situ transmission electron microscopy heating experiments to study phase and microstructural evolution in several unirradiated U-10Zr specimens during rapid heating ramps (from room temperature to 1000 °C). The starting a-U + bcc-(Zr, U) eutectic microstructure began to decompose above 600 °C. The decomposition initiated from the bcc (U,Zr) phase. Similar results were observed for all specimens even when fabricated by different routes (e.g., cold rolled or annealed). As a result, the impact of observed microstructure and phase evolutions at high temperatures on fuel fabrication and in-pile fuel transient test was also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Structural features of early fuel cycle taggant incorporation for intentional nuclear forensics

To develop strategies for incorporating transition metal taggants (Fe, Cr, and Ni) into oxide fuels and to understand how these taggant candidates persist through early fuel cycle processes, synthetic procedures are modified from established production routes to yield intentionally tagged early fuel cycle intermediates including uranyl nitrate hexahydrate (UNH, UO 2 (NO 3 ) 2 ·6H 2 O), uranyl peroxide tetrahydrate (studtite, UO 2 O 2 ·4H 2 O), and uranyl peroxide dihydrate (metastudtite, UO 2 O 2 ·2H 2 O). First, Fe, Cr, and Ni nitrate solutions are introduced to an aqueous solution of UNH followed by precipitation to produce tagged UNH. Then, studtite is precipitated from UNH followed by dehydration to metastudtite. Structural influences of taggant incorporation within all synthesized phases are investigated using powder X-ray diffraction (PXRD) and Raman spectroscopy to provide insight into crystallographic modifications resulting from the addition of tags to these early fuel cycle materials and elucidate the chemical form of taggants introduced at these stages. The possibility of segregation of taggant species into discrete phases within U matrices was examined using scanning electron microscopy with energy dispersive X-ray spectroscopy. Taggant concentrations in solid-phase materials were determined using inductively coupled plasma-optical emission spectroscopy. Observations from Raman spectroscopy and PXRD indicate that introducing transition metal tags during uranyl nitrate precipitation results in potential impurity phase segregation in UNH, but transition metal incorporation is suggested by results for tagged uranyl peroxide materials. Further, results from this study will inform strategies for optimizing taggant incorporation in UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Identification of uranium oxidation states using oxygen K-edge scanning transmission X-ray microscopy

The field of nuclear forensics is growing in importance, and the increasing capabilities at synchrotron radiation light sources enable non-destructive characterization of oxide particles with better spatial, compositional, and oxidation state speciation resolution than ever before. Here, uranium oxide particles derived from multiple wet chemical processing methods were examined using a scanning transmission X-ray microscope (STXM), and a weakly-supervised method was developed to automatically analyze the collected data. Multiple uranium oxidation states were observed and quantified within and between samples, yielding information about differences between particles produced via the various processing routes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

High-temperature nanoindentation creep studies on castable and sintered nanostructured low-activation ferritic-martensitic alloys

In this article, we present the creep characteristics of two reduced activation ferritic-martensitic steels of identical starting compositions formed by different fabrication routes: a nanostructured ferritic alloy commonly referred to as a castable nanostructured alloy (CNA) and a sintered nanostructured alloy (SNA) variant. Through a series of nanoindentation experiments spanning a temperature range of 25 °C to 650 °C, with a maximum load of 100 mN, we find creep behaviors in the cast and sintered materials to be remarkably similar. The creep stress exponent (n) for CNA and SNA were found to be in the range of 8–35 and the activation volume was ∼14–42b 3 , underscoring a dominance of dislocation-mediated mechanisms in both alloys. Notably, we observed a decline in the creep stress exponent with increasing temperature, attributable to the heightened influence of thermally activated dislocations. This phenomenon suggests a potential transition in the deformation mechanism towards a thermally activated dislocation climb process, significantly impacting the observed creep behavior.

36 MATERIALS SCIENCE↗