Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “niobium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Design of Silicide-Strengthened Nb–Si–Cr–(Mo) alloys for additive manufacturing

Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Commissioning of a two-target DC cylindrical magnetron sputter coater for depositing Nb 3 Sn film on Nb superconducting radiofrequency cavities

A DC cylindrical magnetron sputter coater was commissioned and used to coat Nb 2.6 GHz superconducting radiofrequency (SRF) cavity with Nb 3 Sn. The sputter coater has two identical cylindrical magnetrons that can move, with a controlled speed, along the axis of the SRF cavity to coat the inside surface of the cavity. The design of the sputter coater is discussed, along with its performance. Initially, a sample holder that allows coating on flat substrates at positions similar to the equator and beam tubes of a 2.6 GHz SRF cavity was used to test conditions for fabricating Nb 3 Sn layers. Multilayers of Nb and Sn were sequentially sputtered on flat Nb and sapphire substrates mounted on the equivalent positions of the cavity's beam tubes and the equator using the two identical cylindrical magnetrons. Then, the Nb/Sn multilayers were annealed at 950 °C for 3 h. Here, the ~1.2 μm thick Nb 3 Sn film did not show any other Nb–Sn compounds and had a superconducting transition temperature of 17.61–17.76 K. The 2.6 GHz SRF cavity was coated using similar conditions as flat samples. Cryogenic RF testing of the Nb 3 Sn-coated cavity demonstrated a quality factor of 3.2 × 10 8 at an accelerating gradient of 5 MV/m at 4.4 K.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Insights into Dopant-Mediated Tuning of Silica-Supported Mo Metal Centers for Enhanced Olefin Metathesis

Here, we show that the electronic environment around active Mo centers supported on mesoporous silicates can be tuned by the addition of transition metals creating highly dispersed bimetallic catalysts that display enhanced activity for ethylene + 2-butene metathesis to propylene. The bimetallic catalysts are prepared by incorporating electrophilic Lewis acid metals (M) such as Nb, Ta, Zr, or Hf as dopant promoters into mesoporous KIT-6 supports using a one-pot sol–gel technique followed by impregnation of the Mo species. All the bimetallic Mo/M-KIT-6 catalysts display better activity than monometallic Mo/KIT-6 catalyst (28.7 ± 1.1 mmol (mol Mo s ) –1 ), with (Mo/Nb-KIT-6) catalysts exhibiting maximum propylene formation rates (54.2 ± 0.5 mmol (mol Mo s ) –1 ) at an identical Mo loading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Low-loss millimeter-wave resonators with an improved coupling structure

Millimeter-wave superconducting resonators are a useful tool for studying quantum device coherence in a new frequency domain. However, improving resonators is difficult without a robust and reliable method for coupling millimeter-wave signals to 2D structures. We develop and characterize a tapered transition structure coupling a rectangular waveguide to a planar slotline waveguide with better than 0.5 dB efficiency over 14 GHz, and use it to measure ground-shielded resonators in the W band (75–110 GHz). Having decoupled the resonators from radiative losses, we consistently achieve single-photon quality factors above 10 5 , with a two-level-system loss limit above 10 6 , and verify the effectiveness of oxide removal treatments to reduce loss. These values are 4–5 times higher than those previously reported in the W band, and much closer to typical planar microwave resonators. The improved losses demonstrated by these on-chip millimeter-wave devices shed new light on quantum decoherence in a different frequency regime, offer increased selectivity for high-frequency detectors, and enables new possibilities for hybrid quantum experiments integrating millimeter-wave frequencies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Analysis of thermal grooving effects on vortex penetration in vapor-diffused Nb 3 Sn

While Nb 3 Sn theoretically offers better superconducting radio-frequency (RF) cavity performance (Q 0 and E acc ) to Nb at any given temperature, peak RF magnetic fields consistently fall short of the ~400 mT prediction. The relatively rough topography of vapor-diffused Nb 3 Sn is widely conjectured to be one of the factors that limit the attainable performance of Nb 3 Sn-coated Nb cavities prepared via Sn vapor diffusion. Here we investigate the effect of coating duration on the topography of vapor-diffused Nb 3 Sn on Nb and calculate the associated magnetic field enhancement and superheating field suppression factors using atomic force microscopy topographies. It is shown that the thermally grooved grain boundaries are major defects which may contribute to a substantial decrease in the achievable accelerating field. Further, the severity of these grooves increases with total coating duration due to the deepening of thermal grooves during the coating process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Design of Stand-Alone Cryomodule based on Superconducting Quarter-Wave Resonator

Present superconducting accelerators require a central refrigeration system and piping to distribute liquid helium and nitrogen. Stand-alone cryocooler-based systems are of significant interest both to scientific and industrial customers, as they allow applications at facilities where no cryogenic equipment and expertise exists, where it is undesirable to develop additional cryogenic systems, or where a mobile system that can be transported between beamlines or facilities is required. The technical challenge of this approach is to minimize the heat losses to the liquid helium so that commercially available, self-contained cryocoolers are able to handle the thermal load. This paper presents an improved design for a stand-alone quarter-wave resonator (QWR) cryomodule a based on commercially available cryocoolers. This cryomodule has a particular application in the ATLAS intensity upgrade project where it will house a 72.75 MHz QWR for beam energy adjustments to experimental areas, where no helium cryogenic systems exist. The described cryomodule may also be the critical part of a turnkey system with application to material processing, semiconductor manufacturing, food irradiation and homeland security. The development of low heat loss peripheral components reduces cost and widens applicability of the system. We will discuss the cryomodule and RF coupler designs, including numerical thermal and structural analyses.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Reassembly and Test of High-Field Nb3Sn Dipole Demonstrator MDPCT1

In the framework of the U.S. Magnet Development Program (MDP), Fermilab has developed and tested a high-field Nb$_3$Sn dipole demonstrator MDPCT1 for a post-LHC Hadron Collider. The magnet was first assembled with a lower coil pre-load to minimize the risk of coil damage during assembly and test. In the first test the magnet reached its test goal producing a world record field of 14.1 T at 4.5 K. Next the magnet was reassembled with nominal pre-load to achieve its design field limit of 15 T. This paper describes the details of MDPCT1 inspection, design modifications and reassembly. The magnet quench performance, including training, ramp rate and temperature dependences in the temperature range of 1.9-4.5 K, is presented and discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Effects of Grain Size and Interstitial Content on Recrystallization in Nb after Cold Rolling

A fully recrystallized microstructure with a fine grain size can improve the performance of superconducting radio-frequency (SRF) cavities produced from high-purity Nb (ASTM B393–18 Type 5 Nb) while providing mechanical strength. Recrystallization depends on impurity content, initial microstructure, deformation state, and annealing conditions. To better understand how fine-grained, fully recrystallized microstructures may be produced, the recrystallization behaviors of Type 5 and Type 2 Nb materials were studied. Type 5 Nb specimens were produced with both fine and coarse initial grain sizes. All were cold rolled and then annealed under vacuum for one hour to determine the rolling reductions and temperatures required for recrystallization. The recrystallized fraction exceeded 95% in fine-grained Type 5 Nb rolled to a 30% or greater thickness reduction and then annealed at 800 °C or higher. The coarse grained Type 5 Nb required greater rolling reductions to produce any recrystallized grains at 800 °C. The higher interstitial content of the Type 2 Nb required a temperature of 1000 °C or higher to reach a recrystallized fraction greater than 95% in specimens rolled to a 60% reduction. Recrystallization is more easily achieved during annealing at a given temperature for a set time by increasing rolling reduction, decreasing interstitial content, and decreasing initial grain size prior to cold rolling. In conclusion, to avoid grain growth following recrystallization, which increases grain size, the minimum time and temperature necessary for complete recrystallization should be applied.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Impacts to FeRAM design arising from interfacial dielectric layers and wake up modulation in ferroelectric hafnium zirconium oxide

As ferroelectric hafnium zirconium oxide (HZO) becomes more widely utilized in ferroelectric microelectronics, integration impacts of intentional and non-intentional dielectric interfaces and their effects upon the ferroelectric film wake up and circuit parameters become important to understand. In this work, the effect of the addition of a linear dielectric aluminum oxide, Al 2 O 3 , below a ferroelectric Hf 0.58 Zr 0.42 O 2 film in a capacitor structure for FeRAM applications with NbN electrodes was measured. Depolarization fields resulting from the linear dielectric is observed to induce a reduction of the remanent polarization of the ferroelectric. Addition of the aluminum oxide also impacts the wake up of the HZO with respect to the cycling voltage applied. Intricately linked to the design of a FeRAM 1C/1T cell, the metal-ferroelectric-insulator-metal (MFIM) devices are observed to significantly shift charge related to the read states based on aluminum oxide thickness and wake up cycling voltage. As a result, a 33% reduction in the separation of read states is measured, which complicates how a memory cell is designed and illustrates the importance of clean interfaces in devices.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

The Effect of Process History on Grain Boundaries and Dislocation Substructures on Functional Properties of Nb for SRF Cavities: Plastic Formability and Microstructural Evolution. Final report

While much progress has been made in improving the performance of cavities in the past decade, reproducible performance remains elusive. This renewal of “The cost of grain boundaries on the performance of superconducting cavities” examines in further depth the interactions between forming and annealing processes and functional performance at the scale of dislocation substructure and grain boundaries. There are five tasks identified in the renewal, which are: Characterization / analysis of current cavity technology: Effect of deformation, heat treatment, surface treatments, and residual damage on cavity function (Lee and Bieler) Characterization of dislocation mechanisms in single and bicrystals (Bieler) Quantifying effects of impurities and deformation mechanisms in Nb using density functional theory calculations (Solanki) Crystal plasticity constitutive model development (Pourboghrat and Eisenlohr) Modeling and measuring thermal conductivity in thin layers (Wright)

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of High Performance Medium Velocity Superconducting Elliptical Cavities for Hadron Linacs

There is a solid scientific need for continuous wave (CW) proton or heavy ion linear accelerators (linacs) in the energy range up to about 1 GeV per nucleon (GeV/u). Only superconducting (SC) cavities can provide cost-efficient acceleration in CW mode. While low velocity, bc < 0.5 (b is the relative velocity of a charged particle and c is the speed of light), and high velocity, bc > 0.9, SC accelerating structures are established, there is a need in high-performance medium velocity SC accelerating structures. Currently, no superconducting (SC) CW proton or ion accelerators operate in the medium velocity range. We have developed a robust technology for producing high-performance medium-velocity elliptical cavities operating in the frequency range between 600 and 700 MHz. The project was performed in collaboration with Fermi and Argonne National Laboratories. The 5-cell, βopt = 0.65, 644 MHz elliptical cavities built at MSU have been used for this research. An advanced surface treatment method based on nitrogen doping to achieve a high-quality factor and a high accelerating gradient has been demonstrated. The surface treatment has been performed at ANL, and nitrogen doping at FNAL. A stable resonance control with the slow and fast tuner system has also been verified. FNAL developed a dedicated resonance control system for the stable operation of the combined tuner.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Characterization of dissipative regions of a N-doped superconducting radio-frequency cavity

We report radio-frequency measurements of quality factors and temperature mapping of a nitrogen doped Nb superconducting RF cavity. Cavity cutouts of hot and cold spots were studied with low temperature scanning tunneling microscopy and spectroscopy, X-ray photoelectron spectroscopy and secondary electron microscopy. Temperature mapping revealed a substantial reduction of the residual resistance upon cooling the cavity with a greater temperature gradient and hysteretic losses at the quench location, pointing to trapped vortices as the dominant source of residual surface resistance. Analysis of the tunneling spectra in the framework of a proximity effect theory shows that hot spots have a reduced pair potential and a wider distribution of the contact resistance between the Nb and the top Nb oxide. Alone, these degraded superconducting properties account for a much weaker excess dissipation as compared with the vortex contribution. Based on the correlation between the quasiparticle density of states and temperature mapping, we suggest that degraded superconducting properties may facilitate vortex nucleation or settling of trapped flux during cooling the cavity through the critical temperature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Phase Stability in U-6Nb Alloy Doped with Ti from the First Principles Theory

First-principles calculations within the density-functional-theory (DFT) approach are conducted in order to explore and explain the effect of small amounts of titanium on phase stability in the U-6Nb alloy. During rapid quenching from high to room temperature, metastable phases α' (orthorhombic), α" (monoclinic), and γ 0 (tetragonal) can form, depending on Nb concentration. Important mechanical properties depend on the crystal structure and, therefore, an understanding of the effect of impurities on phase stability is essential. Insights on this issue are obtained from quantum-mechanical DFT calculations. The DFT framework does not rely on any material-specific assumptions and is therefore ideal for an unbiased investigation of the U-Nb system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the Sintering Behavior of Nb2O5 and Ta2O5 Mixed Oxide Powders

A mixed oxide system consisting of Nb2O5 and Ta2O5, was subjected to annealing in air/hydrogen up to 950 °C for 1–4 h to study its sintering behavior. The thermogravimetric–differential scanning calorimetry (TGA–DSC) thermograms indicated the formation of multiple endothermic peaks at temperatures higher than 925 °C. Subsequently, a 30% Ta2O5 and 70% Nb2O5 (mol%) pellet resulted in good sintering behavior at both 900 and 950 °C. The scanning electron microscope (SEM) images corroborated these observations with necking and particle coarsening. The sintered pellets contained a 20.4 and 20.8% mixed oxide (Nb4Ta2O15) phase, along with Ta2O5 and Nb2O5, at both 900 and 950 °C, indicating the possibility of the formation of a solid solution phase. In situ high-temperature X-ray diffraction (XRD) scans also confirmed the formation of the ternary oxide phase at 6 and 19.8% at 890 and 950 °C, respectively. The Hume–Rothery rules could explain the good sintering behavior of the Ta2O5 and Nb2O5 mixed oxides. An oxide composition of 30% Ta2O5 and 70% Nb2O5 (mol%) and a sintering temperature of 950 °C appeared adequate for fabricating well-sintered oxide precursors for subsequent electrochemical polarization studies in fused salts.

36 MATERIALS SCIENCE↗
NASA NTRS1960

DETERMINATION OF EMISSIVITY OF MATERIALS.

During the third quarter of the contractual year of Contract NASW-104 for the determination of emissivity of materials, the emittance of nine specimens was measured at temperatures ranging up to 2200F and at pressures averaging 10(exp -8) mm Hg. The materials tested included columbium, columbium with an oxidized surface, molybdenum, graphite varnish on Type 310 stainless steel, stainless steel with an oxidized surface, and platinum black. In the spectral emittance rig, spectral as well as total emittance was measured on three specimens and total emittance only was measured on a fourth. In the total emittance rig, total emittance data was obtained on five specimens. Two of the specimens were endured. Investigations were made concerning the operational characteristics of both rigs in order to eliminate possible sources of error in the data. On the spectral emittance rig, tests were conducted to determine the exact magnitude of any error introduced in the spectral emittance values by beam intermixing resulting from imperfections in the optical system. On the total emittance rig, work was concentrated on the determination of the relative accuracy of the chromel-alumel and platinum-platinum 10% rhodium thermocouples used to measure the temperature of the specimen.

Emission↗