SEARCH · Engineering Papers

Results for “furnaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Evaluation of low cost/high temperature fiber and blanket insulation

Twelve fiber materials comprising water-felted fiber cakes and blanket insulation were subjected to furnace exposures at 1000, 1200, 1400, and 1600 C for up to 500 hours to establish the time-temperature limits below which these insulation materials can withstand repeated thermal cycles without detrimental shrinkage, thermal conductivity increase, or physical changes. Test samples were inspected periodically during the exposure cycles and weight loss and dimensional shrinkage were measured. Density, fiber crystallography, and thermal conductivity were measured after exposure and properties were compared with those of unexposed controls.

Strauss, E. L.↗

NASA NTRS1977

Open-Cycle Gas Turbine/Steam Turbine Combined Cycles with synthetic fuels from coal

The Open-Cycle Gas Turbine/Steam Turbine Combined Cycle can be an effective energy conversion system for converting coal to electricity. The intermediate step in this energy conversion process is to convert the coal into a fuel acceptable to a gas turbine. This can be accomplished by producing a synthetic gas or liquid, and by removing, in the fuel conversion step, the elements in the fuel that would be harmful to the environment if combusted. In this paper, two open-cycle gas turbine combined systems are evaluated: one employing an integrated low-Btu gasifier, and one utilizing a semi-clean liquid fuel. A consistent technical/economic information base is developed for these two systems, and is compared with a reference steam plant burning coal directly in a conventional furnace.

Shah, R. P.↗

NASA NTRS1978

Measurement of the time-temperature dependent dynamic mechanical properties of boron/aluminum composites

A relatively simple flexural vibration test is developed for accurate measurement of the low-strain dynamic modulus and damping capacity of B/Al composite bar specimens from -200 C to over 500 C. The specimens are prepared from 8-ply unidirectional panels containing 50 volume percent fibers composed of 203-micron commercial boron-on-tungsten fibers. The basic test technique consists of the forced flexural vibration of the composite bar specimens at their two lowest free-free symmetrical resonant modes in a high-vacuum cryostat furnace. Specimen damping is determined from oscilloscope photographs of the free decay obtained after simultaneously removing the resonant drive signal and grounding the vibration-drive electrode. The availability of time-temperature dynamic data coupled with the predictive accuracy of composite theory suggests a future potential for using such data in examining environmental effects on composite macrostructure and microstructure.

Dicarlo, J. A.↗

NASA NTRS1977

Dynamic crystallization experiments bearing on the origin of textures in impact-generated liquids

Dynamic crystallization experiments on a synthetic glass of 14310 composition show that the density and distribution of crystals present at the initiation of cooling can drastically affect the texture of the crystallized product. Experiments were performed in one-atmosphere gas-mixing furnaces at an oxygen fugacity slightly below iron-wustite, and precooling crystallization, cooling history, and melt history were systematically varied. When cooled from a complete liquid, the experimental charges were porphyritic with 1-2 mm phenocrysts set in a very fine-grained matrix (less than 0.1 mm). This result suggests that 14310 did not cool from a complete melt. When cooled from a crystal-liquid mixture, the experimental charges had widely varying textures depending on the density and distribution of crystals that act as nucleation sites. It is suggested that the close spatial association of widely divergent textures in the matrices of some breccias and rocks might arise in this manner; local variations in cooling rates are not required.

Lofgren, G. E.↗

NASA NTRS1975

Experimental modeling of the cooling history of Apollo 12 olivine basalts

An analog of the Apollo 12 olivine vitrophyres has been crystallized in a 1-atm gas-mixing furnace at cooling rates ranging between 1250 and 0.7 C/hr and isothermally at degrees of supercooling ranging from 10 C to 325 C. Mineral chemistry, crystal shapes, grain sizes and textures are systematically related to cooling rate and degree of supercooling. At linear cooling rates not exceeding 40 C/hr the texture is porphyritic - large olivine crystals are set in a groundmass of finer-grained pyroxene, plagioclase, and ilmenite; a later generation of olivine never crystallizes. There are three shapes of olivine crystals in the Apollo 12 olivine vitrophyres: glomerocrysts of subhedral crystals, large subequant skeletons, and highly elongate skeletons. These result from three generations of nucleation and a two-stage cooling history - a slow preeruption stage and a rapid continuously increasing posteruption stage. It seems likely that the Apollo 12 olivine basalt magmas were erupted with olivine crystals in suspension. The nucleation temperature of olivine in cooling-rate experiments is dependent on the experimental technique, and hence results of cooling experiments should be applied with caution.

Donaldson, C. H.↗

NASA NTRS1979

Differential oil flowmeter

Difference in oil flow volume through two mechanical flowmeters is converted to analog signal by simple inexpensive circuit. Circuit can be implemented with only minor changes to conventional oil flowmeters and used to measure fuel consumed by oil fired furnace or water heater.

Powers, W. T.↗

NASA NTRS1980

Repairing ceramic insulating tiles

Fused-silica tiles containing large voids or gauges are repaired without adhesives by plug insertion method. Tiles are useful in conduits for high-temperature gases, in furnaces, and in other applications involving heat insulation.

Dunn, B. R.↗

NASA NTRS1980

Thermal jack

Auxiliary furnace tool forces part to match length of mating part during brazing. As brazed assembly cools, jack contracts faster and disengages from fitting studs.

Armenoff, C. T.↗

NASA NTRS1978

Application of semiconductor diffusants to solar cells by screen printing

Diffusants were applied onto semiconductor solar cell substrates, using screen printing techniques. The method was applicable to square and rectangular cells and can be used to apply dopants of opposite types to the front and back of the substrate. Then, simultaneous diffusion of both dopants can be performed with a single furnace pass.

Evans, J. C., Jr.↗

NASA NTRS1978

Shear rupture of a directionally solidified eutectic gamma/gamma prime - alpha (Mo) alloy

Directionally solidified Mo alloys are evaluated to determine the shear rupture strength and to possibly improve it by microstructural and heat treatment variations. Bars of the alloy containing nominally 5.7% Al and 33.5% Mo by weight with balance Ni were directionally solidified at rates between 10 and 100 mm per hour in furnaces with thermal gradients at the liquid-solid interface of 250 or 100 C per cm. A limited number of longitudinal shear rupture tests were conducted at 760 C and 207 MPa in the as - solidified and in several heat treated conditions. It is shown that shear rupture failures are partly transgranular and that resistance to failure is prompted by good fiber alignment and a matrix structure consisting mainly of gamma prime. Well aligned as - solidified specimens sustained the shear stress for an average of 81 hours. A simulated coating heat treatment appeared to increase the transformation of gamma to gamma prime and raised the average shear life of aligned specimens to 111 hours. However, heat treatments at 1245 C and especially at 1190 C appeared to be detrimental by causing partial solutioning of the gamma prime, and reducing lives to 47 and 10 hours, respectively.

Harf, F. H.↗

NASA NTRS1978

Silicon Sheet Growth Development for the Large Area Sheet Task of the Low Cost Solar Array Project. Heat Exchanger Method - Ingot Casting Fixed Abrasive Method - Multi-Wire Slicing

Solar cells fabricated from HEM cast silicon yielded up to 15% conversion efficiencies. This was achieved in spite of using unpurified graphite parts in the HEM furnace and without optimization of material or cell processing parameters. Molybdenum retainers prevented SiC formation and reduced carbon content by 50%. The oxygen content of vacuum cast HEM silicon is lower than typical Czochralski grown silicon. Impregnation of 45 micrometers diamonds into 7.5 micrometers copper sheath showed distortion of the copper layer. However, 12.5 micrometers and 15 micrometers copper sheath can be impregnated with 45 micrometers diamonds to a high concentration. Electroless nickel plating of wires impregnated only in the cutting edge showed nickel concentration around the diamonds. This has the possibility of reducing kerf. The high speed slicer fabricated can achieve higher speed and longer stroke with vibration isolation.

Schmid, F.↗

NASA NTRS1978

System Design Package for SIMS Prototype System 3, Solar Heating and Domestic Hot Water

A collation of documents and drawings are presented that describe a prototype solar heating and hot water system using liquid flat plate collectors and a gas or electric furnace energy subsystem. The system was designed for installation into a single-family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system are packaged for evaluation of the system with information sufficient to assemble a similar system.

Source record↗

NASA NTRS1978

Analysis and evaluation of process and equipment in tasks 2 and 4 of the Low Cost Solar Array project

Several experimental and projected Czochralski crystal growing process methods were studied and compared to available operations and cost-data of recent production Cz-pulling, in order to elucidate the role of the dominant cost contributing factors. From this analysis, it becomes apparent that substantial cost reductions can be realized from technical advancements which fall into four categories: an increase in furnace productivity; the reduction of crucible cost through use of the crucible for the equivalent of multiple state-of-the-art crystals; the combined effect of several smaller technical improvements; and a carry over effect of the expected availability of semiconductor grade polysilicon at greatly reduced prices. A format for techno-economic analysis of solar cell production processes was developed, called the University of Pennsylvania Process Characterization (UPPC) format. The accumulated Cz process data are presented.

Goldman, H.↗

NASA NTRS1979

LSA Large Area Silicon Sheet Task Continuous Liquid Feed Czochralski Growth

A process for the continuous growth of crystals by the Czochralski method, suitable for producing single silicon crystals for use in solar cells was studied. Continuous growth is the growth of 100 Kg of single silicon crystals, 10 cm in diameter, from one container. A furnace with continuous liquid replenishment of the growth crucible, accomplished by a melt-down system and a liquid transfer mechanism, with associated automatic feedback controls was developed. Elements of the transfer system were further developed and tested during actual transfer runs. Considerable simplification of the heating element of the transfer tube was achieved. Accuracy and reliability of the temperature sensor, which is part of the power input control system for the transfer tube, was improved. Electrical and thermal effectiveness were increased while assembly of the transfer tube system was further simplified.

Fiegl, G.↗

NASA NTRS1979

Large Area Silicon Sheet by EFG

Progress made in the development of EFG ribbon growth is discussed. Specific areas covered include: (1) demonstration of multiple growth for ribbons 5 cm wide in runs of 12 and 20 hours duration; (2) a single cartridge crystal growth station was built expanding observational capacity by virtue of an anamorphic optical-video system which allows close observation of the meniscus over 7.5 cm wide, as well as video taping of the ribbon growth process; (3) growth station no.1 achieved reproducible and reliable growth of 7.5 cm wide ribbon at speeds up to 4 cm/min; (4) introduction of the 'mini cold shoe'; (5) increases in cell efficiency due to interface shaping using the 'displaced die' concept; and (6) clarification of the role of gaseous impurities in cartridge furnaces and stabilization of their destabilizing influence on growth.

Wald, F. V.↗

NASA NTRS1979

Thermal analysis of Bridgman-Stockbarger growth

A thermal analysis of a cylindrical HgCdTe sample in a Bridgman-Stockbarger crystal growth configuration was conducted with emphasis on the thermal profile, interface shape and position, and the thermal gradients at the liquid-solid interface. Alloys of HgTe and CdTe with compositions approximating 20 percent CdTe, 80 percent HgTe were used. This composition results in a bandgap suited for the detection of 10.6 micron CO2 radiation. The sensitivity of the sample thermal characteristics to important growth parameters, such as thermal diffusivities, thermal conductivities, furnace temperature profile, ampoule dimensions, and growth velocity was assessed. Numerical techniques and associated computational models necessary to analyze the heat transfer process within the sample and the Bridgman-Stockbarger boundary conditions were developed. This thermal analysis mode was programmed in FORTRAN V, and is currently operational on the MSFC Univac 1100 system.

Knopf, F. W.↗

NASA NTRS1979

Large Area Silicon Sheet by EFG

Displaced die concepts were explored along with some initial work on buckle characterization. Convective impurity redistribution was further studied. Growth from single cartridges was continued to create a quality baseline to allow comparison of the results with those in the upcoming multiple run and to choose the most appropriate die design. Fabrication and assembly work on the actual five ribbon furnace continued. Progress was made toward the development of the video optical system for edge position and meniscus height control. In preparation for a detailed program, designed to explore the buckling problem, ribbon guidance in the machine was improved. Buckle free, full width ribbon was grown under stable conditions without a cold shoe, an achievement essential to finally arrive at quantitative correlations between growth conditions and buckle formation.

Wald, F. V.↗

NASA NTRS1979

Development of Pulsed Processes for the Manufacture of Solar Cells

The development status of the process based upon ion implantation for the introduction of junctions and back surface fields is described. A process sequence is presented employing ion implantation and pulse processing. Efforts to improve throughout and descrease process element costs for furnace annealing are described. Design studies for a modular 3,000 wafer per hour pulse processor are discussed.

Source record↗