Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrochemical analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Performance Losses and Current-Driven Recovery from Cation Contaminants in PEM Water Electrolysis

Water contaminants are a common cause of failure for polymer electrolyte membrane (PEM) electrolyzers in the field as well as a confounding factor in research on cell performance and durability. In this study, we investigated the performance impacts of feed water containing representative tap water cations at concentrations ranging from 0.5–500 μ M, with conductivities spanning from ASTM Type II to tap-water levels. We present multiple diagnostic signatures to help identify the presence of contaminants in PEM electrolysis cells. Through analysis of polarization curves and impedance spectroscopy to understand the origins of performance losses, we found that a switch from the acidic to alkaline hydrogen evolution mechanism is a key factor in contaminated cell behavior. Finally, we demonstrated that this mechanism switching can be harnessed to remove cation contaminants and recover cell performance without the use of an acid wash. We demonstrated near-complete recovery of cells contaminated with sodium and calcium, and partial recovery of a cell contaminated with iron, which was further investigated by post-mortem microscopy. The improved understanding of contaminant impacts from this work can inform development of strategies to mitigate or recover performance losses as well as improve the consistency and rigor of electrolysis research.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Lithium-Ion Battery Life Model with Electrode Cracking and Early-Life Break-in Processes

This paper develops a physically justified reduced-order capacity fade model from accelerated calendar- and cycle-aging data for 32 lithium-ion (Li-ion) graphite/nickel-manganese-cobalt (NMC) cells. The large data set reveals temperature-, charge C-rate-, depth-of-discharge-, and state of charge (SOC)-dependent degradation patterns that would be unobserved in a smaller test matrix. Model structure is informed by incremental capacity analysis that shows loss of lithium inventory and cathode-material loss as the dominant capacity fade mechanisms. The model includes terms attributable to solid-electrolyte interface (SEI) growth, electrode cracking, cycling-driven acceleration of SEI growth, and "break-in" mechanisms that slightly decrease or increase available Li inventory early in life. The study explores what mathematical couplings of these mechanisms best describe calendar aging, cycle aging, and mixed calendar/cycle aging. Various approaches are discussed for extracting relevant stress factors from complex cycling profiles to predict lifetime during real-world battery loads using models trained on constant-current laboratory test results. The complexity of the present human-driven model identification process motivates future work in machine learning to more widely search and statistically discern the optimal model that correctly extrapolates capacity fade based on physical knowledge.

25 ENERGY STORAGE↗
DOE OSTI2026

Gas-driven short disconnection mitigates thermal runaway in Li-ion batteries under mechanical abuse

Mechanical abuse poses a critical safety risk to Li-ion batteries by inducing internal short circuits that initiate thermal runaway. Remarkably, voltage recovery frequently emerges during thermal runaway initiation, a phenomenon that conventional theories fail to explain. Here, our study develops a new multiphysics mechanism to explain voltage recovery, termed gas-driven short disconnection, whereby internal gas pressure mechanically disengages short-circuit contacts and causes the cell voltage to rebound. This mechanism incorporates gas generation and its structural impact on the short circuit. Real-time optical and thermal imaging and X-ray computed tomography reveal fluid-structure interaction between internal gas flow and adjacent shorting contacts. We establish a mechanistic framework linking gas-driven short disconnection to cell-level voltage and temperature responses, elucidating the extension–truncation pattern of voltage recovery. Furthermore, thermal regime maps show that a voltage recovery duration exceeding 5 s correlates with limited temperature rise below 150 °C, indicating that sustained short-circuit disconnection suppresses Joule heating. Additionally, a dimensionless criterion is deduced from scaling analysis for physical plausibility of gas-driven short disconnection in mechanically abused cells. This finding inspires smart venting control, which regulates gas release to maintain the internal pressure while dissipating gas enthalpy, thereby providing a device-level strategy for thermal runaway mitigation.

Gas-driven short disconnection↗
DOE OSTI2020

Intensified Flue Gas Desulfurization Water Treatment for Reuse, Solidification, and Discharge

The goal of this final project report is to summarize the work conducted on project DE-FE0031555. In accordance with the Statement of Project Objectives (SOPO), the University of Kentucky Center for Applied Energy Research (UK CAER) (Recipient) developed a hybrid electrochemical-membrane technology for treating wet flue gas desulfurization (WFGD) blowdown from coal-fired power generation plants that (1) removes government-regulated species and total suspended solids (TSS) via electrocoagulation with solid/liquid separation to avoid further treatments by a biological method specifically for selenium, and (2) reduces total dissolved solids (TDS) in a nanofiltration unit to promote water recycle and reduce freshwater intake. Additional technological configurations were pursued, including (1) nanofiltration combined with zeolite dewatering for a near-zero liquid discharge (ZLD) scenario, and (2) polishing discharge from zeolite dewatering using capacitive deionization (CDI) with 90+% salt rejection to produce water with less than 100ppm TDS for more beneficial use. Project results verified that UK CAER’s hybrid approach addressed the complexities of WFGD blowdown with simplified unit operation at relatively low capital investment by demonstrating: (1) an effective in-situ generated solid sorbent material, green-rust (GR), that specifically removes regulated dissolved species in WFGD blowdown, including selenium, arsenic, and nitrates; (2) a low-cost, high flux nanofiltration treatment that removes both monovalent and divalent species at >80% rejection to adequately provide water recycle and extend the life of FGD equipment by mitigating chloride aided pitting corrosion mechanisms; and (3) a solidification and stabilization process using pozzolanic agents that retain regulated species and satisfy the Resource Conservation and Recovery Act (RCRA) leachate requirements. UK CAER proved electrocoagulation with GR to be an intensified solution for effluent limit guidelines (ELG), and based on preliminary techno-economic analysis (TEA), in comparison to DOE’s Case 1 for Biological Wastewater Treatment that had a purchased equipment cost (PEC) of $\$$5.26 million and a Total plant cost (TPC) of $\$$30.0 million, the EC process had a PEC of $\$$2.67 million and the TPC of $\$$17.0 million. While the electricity consumption for Case 1 was 53 kW, it was 110 kW for the EC process due to dissolving iron for a three-stage reaction design. However, electricity consumption for the EC process could be significantly reduced by adopting a counter-current reactor design for at least a 6-stage chemical reaction operation.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Electrocoagulation Combined with Ultrafiltration Membranes as Pretreatment for RO Desalination of Synthetic Cooling Tower Blowdown Water

Electrocoagulation (EC), an electrochemical water treatment process, is commonly used to remove particulate and colloidal matter from water. Here, in this study, we demonstrate that EC, when coupled with membrane filtration, is also capable of removing dissolved species, such as Ca + , Mg 2+ , and SiO x . The removal of such species is important for downstream membrane-based desalination treatment of the water that can suffer from reduced performance due to membrane scaling. Here, we describe how EC can be combined with a low-pressure membrane (LPM) system to offer efficient (and potentially universal) pretreatment for downstream membrane desalination. Synthetic water, simulating cooling tower blowdown (CTBD) with elevated concentrations of hardness and silicates (Ca: 418 ppm, Mg: 63 ppm, SiO 2 : 50 ppm) is treated using EC coupled to ultrafiltration (UF) to remove Mg up to 30 ± 1%, Ca up to 29 ± 1%, and silica up to 99 ± 1%. We evaluated the effectiveness of the EC-UF pretreatment system in reducing downstream RO scaling using thermodynamic modeling to predict the saturation index (SI) at the RO membrane/water interface. An SI value below zero (SI < 0) indicates under-saturated conditions (with respect to a particular mineral) where mineral scaling does not take place, which correlates with improved water recovery. Our findings suggest that the EC-UF pretreatment system was able to increase water recovery by up to 30%, compared to 0% recovery without pretreatment, under optimal conditions (feed solution pH of 7 and an EC charge loading of 1800 C/L). Finally, we conducted an economic analysis showing that implementing an EC-UF system for CTBD water could yield a cost benefit of up to $\$$14.13 per m 3 compared to direct brine disposal.

cooling tower blowdown↗
DOE OSTI2021

Multi-objective Bayesian optimization of ferroelectric materials with interfacial control for memory and energy storage applications

Optimization of materials’ performance for specific applications often requires balancing multiple aspects of materials’ functionality. Even for the cases where a generative physical model of material behavior is known and reliable, this often requires search over multidimensional function space to identify low-dimensional manifold corresponding to the required Pareto front. In this work, we introduce the multi-objective Bayesian optimization (MOBO) workflow for the ferroelectric/antiferroelectric performance optimization for memory and energy storage applications based on the numerical solution of the Ginzburg–Landau equation with electrochemical or semiconducting boundary conditions. MOBO is a low computational cost optimization tool for expensive multi-objective functions, where we update posterior surrogate Gaussian process models from prior evaluations and then select future evaluations from maximizing an acquisition function. Using the parameters for a prototype bulk antiferroelectric (PbZrO 3 ), we first develop a physics-driven decision tree of target functions from the loop structures. We further develop a physics-driven MOBO architecture to explore multidimensional parameter space and build Pareto-frontiers by maximizing two target functions jointly—energy storage and loss. This approach allows for rapid initial materials and device parameter selection for a given application and can be further expanded toward the active experiment setting. The associated notebooks provide both the tutorial on MOBO and allow us to reproduce the reported analyses and apply them to other systems (https://github.com/arpanbiswas52/MOBO_AFI_Supplements).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Low Melting Temperature Gallium–Indium Liquid Metal Anode for Solid-State Li-Ion Batteries

Solid-state Li-ion batteries are attracting attention for their enhanced safety features, higher energy density, and broader operational temperature range compared to systems based on liquid electrolytes. However, current solid-state Li-ion batteries face performance challenges, such as suboptimal cycling and poor rate capabilities, often due to inadequate interfacial contact between the solid electrolyte and electrodes. To address this issue, we incorporated a gallium–indium (Ga–In) liquid metal as the anode in a solid-state Li-ion battery setup, employing Li 6 PS 5 Cl as the solid electrolyte. Operating at room temperature, this configuration achieved an initial capacity of 389 mAh g –1 and maintained 88% of this capacity after 30 cycles at a 0.05 C rate. It also demonstrated a capacity retention of 66% after 500 cycles at a 0.5 C rate. In comparison to solid anode materials, such as tin, the Ga–In liquid metal exhibited superior cycling stability and rate capacity, which is due to the self-healing and fluid properties of the alloy that ensure stable interfacial contact with solid electrolytes. In situ X-ray diffraction (XRD) and ex situ scanning electron microscope (SEM) analyses revealed that indium does not directly participate in the lithiation/delithiation process. Instead, it helps maintain the alloy’s low melting point, facilitating its return to a liquid state after delithiation. In a comparative analysis of stack pressure during cycling in cells utilizing Ga–In liquid metal and tin, the Ga–In liquid metal cell demonstrated an ability to buffer pressure increases associated with deformation. In conclusion, these findings suggest a promising approach for enhancing solid-state batteries by integrating liquid metal anodes, which improve interfacial contact and stability.

Alloys↗
DOE OSTI2021

(Invited) Understanding Multi-Component Transport and Reaction Phenomena in Bipolar Membranes Used for Electrosynthesis

Bipolar membranes (BPMs), which have long seen usage in electrodialysis reactors for the generation of acid and base, have recently demonstrated potential to become critical components in electrochemical synthesis devices. Because they can operate under large pH gradients, BPMs enable favorable environments for electrocatalysis at the individual electrodes. Critical to the implementation of BPMs in these devices is understanding the kinetics of water dissociation that occurs within the BPM junction as well as the co- and counter-ion crossover through the BPM, which both present significant obstacles to developing efficient and stable BPM-devices for electrosynthesis applications. Prior work has modeled ion transport in bipolar membranes in neutral salt solutions for electrodialysis. However, no model exists for the BPM under the harsh applied pH gradients that would be present in electrosynthesis, and there is significant need to explore the effects of the internal hydration on the lifetime and performance of BPMs in such environments. Additionally, a mechanistic understanding of water dissociation catalysis will be required to develop interfacial catalysts that enable the high current density operation required for scalable electrosynthesis of fuels. In this talk, we discuss modeling methodologies and physics inherent in BPMs and present our recent model of ion transport and water dissociation catalysis in BPMs across the pH scale. Specifically, we simulate multi-ion transport for a BPM with various electrolyte combinations on each side of the membrane, demonstrating the significance of co- and counter-ion crossover in BPMs operating under harsh pH gradients. We then investigate effects caused by hydration gradients that occur due to internal ion-exchange and examine potential methods for improving performance and mitigating crossover. Finally, we examine the impact of the interfacial water dissociation catalyst and perform sensitivity analysis on the key properties (catalyst point of zero charge and pKa) that dictate catalyst performance. These results provide information that is critical to developing a comprehensive understanding of multi-component phenomena in BPMs and to informing the design and implementation of BPMs in next-generation devices for the numerous electrosynthesis chemistries that benefit from operation under an applied pH gradient.

Bui, Justin C↗
NASA NTRS2014

Propagation of Radiosonde Pressure Sensor Errors to Ozonesonde Measurements

Several previous studies highlight pressure (or equivalently, pressure altitude) discrepancies between the radiosonde pressure sensor and that derived from a GPS flown with the radiosonde. The offsets vary during the ascent both in absolute and percent pressure differences. To investigate this problem further, a total of 731 radiosonde-ozonesonde launches from the Southern Hemisphere subtropics to Northern mid-latitudes are considered, with launches between 2005 - 2013 from both longer-term and campaign-based intensive stations. Five series of radiosondes from two manufacturers (International Met Systems: iMet, iMet-P, iMet-S, and Vaisala: RS80-15N and RS92-SGP) are analyzed to determine the magnitude of the pressure offset. Additionally, electrochemical concentration cell (ECC) ozonesondes from three manufacturers (Science Pump Corporation; SPC and ENSCI-Droplet Measurement Technologies; DMT) are analyzed to quantify the effects these offsets have on the calculation of ECC ozone (O3) mixing ratio profiles (O3MR) from the ozonesonde-measured partial pressure. Approximately half of all offsets are 0.6 hPa in the free troposphere, with nearly a third 1.0 hPa at 26 km, where the 1.0 hPa error represents 5 persent of the total atmospheric pressure. Pressure offsets have negligible effects on O3MR below 20 km (96 percent of launches lie within 5 percent O3MR error at 20 km). Ozone mixing ratio errors above 10 hPa (30 km), can approach greater than 10 percent ( 25 percent of launches that reach 30 km exceed this threshold). These errors cause disagreement between the integrated ozonesonde-only column O3 from the GPS and radiosonde pressure profile by an average of +6.5 DU. Comparisons of total column O3 between the GPS and radiosonde pressure profiles yield average differences of +1.1 DU when the O3 is integrated to burst with addition of the McPeters and Labow (2012) above-burst O3 column climatology. Total column differences are reduced to an average of -0.5 DU when the O3 profile is integrated to 10 hPa with subsequent addition of the O3 climatology above 10 hPa. The RS92 radiosondes are superior in performance compared to other radiosondes, with average 26 km errors of -0.12 hPa or +0.61 percent O3MR error. iMet-P radiosondes had average 26 km errors of -1.95 hPa or +8.75 percent O3MR error. Based on our analysis, we suggest that ozonesondes always be coupled with a GPS-enabled radiosonde and that pressure-dependent variables, such as O3MR, be recalculated-reprocessed using the GPS-measured altitude, especially when 26 km pressure offsets exceed 1.0 hPa 5 percent.

pressure measurements↗
DOE OSTI2020

Descriptor-Based Analysis of Atomic Layer Deposition Mechanisms on Spinel LiMn 2 O 4 Lithium-Ion Battery Cathodes

Protective coatings have been shown to effectively suppress Mn ion dissolution from the spinel LiMn 2 O 4 lithium-ion battery cathode by stabilizing the surface against undesired side reactions with the electrolyte. In spite of extensive study, however, there remains a lack of atomic-scale understanding of how such coatings are deposited, and no molecular-level descriptor to predict trends in deposition mechanisms has been identified. We have recently shown that Al 2 O 3 coatings grown by atomic layer deposition (ALD) with alternating trimethylaluminum (TMA) and water exposures exhibit submonolayer growth because of precursor decomposition on the lithium manganate spinel (LMO) surface during early ALD pulses. In the present work, we elucidate the underlying mechanisms of this Al 2 O 3 ALD process using density functional theory (DFT) calculations and X-ray photoelectron spectroscopy (XPS) experiments, and we introduce a generalized descriptor-based framework to understand the resulting trends across a spectrum of surface structures and functionalities. We demonstrate that all decomposition products, including CH 3 -aluminum adducts and dissociated CH 3 groups, are Lewis bases and are coordinated to oxygen atoms on the LMO surface, leading to charge transfer to Lewis acidic Mn 3d states. Inert-transfer XPS supports these theoretical predictions, showing an increase in near-surface Mn 3+ content following TMA exposure and shifts in C is spectra consistent with C-O bond formation. We extend the DFT studies to various low- and high-index LMO surface facets, as a proxy for tuning the Lewis acid-base interactions between surface-bound CH 3 * and near-surface Mn ions. The thermochemistry for TMA reactions on these chemically distinct LMO surfaces demonstrates that ALD is structure-sensitive and that there is higher reactivity for TMA decomposition and Al 2 O 3 nucleation near LMO steps and defects. Motivated by the Lewis basic character of the decomposition products, we introduce the oxygen vacancy formation energy as a descriptor for decomposition energetics, and we demonstrate that all energetics are correlated to this quantity through the number of electrons that are transferred along the reaction coordinate. Finally, based on these findings, we hypothesize that improved electrochemical cycling with only 1-2 ALD cycles may be due to selective passivation of defect sites on the LMO surface that are more susceptible to Mn dissolution, and we suggest that similar descriptor-based analyses could be useful for the study of other ALD coatings on oxide substrates.

25 ENERGY STORAGE↗
DOE OSTI2024

The Influence of Alkyl Spacers and Molecular Weight on the Charge Transport and Storage Properties of Oxy‐Bithiophene‐Based Conjugated Polymers

Conjugated polymers (CPs) with polar side chains can conduct electronic and ionic charges simultaneously, making them promising for bioelectronics, electrocatalysis and energy storage. Recent work showed that adding alkyl spacers between CP backbones and polar side chains improved electronic charge carrier mobility, reduced swelling and enhanced stability, without compromising ion transport. However, how alkyl spacers impact polymer backbone conformation and, subsequently, electronic properties remain unclear. In this work, we design two oxy-bithiophene-based CP series, each featuring progressively extended alkyl spacer lengths and two distinct molecular weight (MW) distributions. Using operando characterisations, we evaluate the (spectro)electrochemical and swelling properties of the polymer thin films, and their performance in organic field-effect transistors and organic electrochemical transistors. Surprisingly, alkyl spacers negatively impact the hole mobility of our polymers, with higher MW amplifying this effect. Using molecular dynamics simulations, we show that it is thermodynamically favourable for adjacent non-polar alkyl spacers to aggregate in polar electrolytes, leading to backbone twisting. Further spectroscopic measurements corroborate this prediction. Our findings demonstrate the active interactions between side chain structure, MW and electrolyte/solvent polarity in influencing polymer performance, underscoring the importance of considering solvation environment effects on polymer conformation when designing new mixed conducting CPs for electrochemical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Insights into the Cathode–Electrolyte Interphases of High-Energy-Density Cathodes in Lithium-Ion Batteries

Here we present a comprehensive study of cycled high-Ni (LiNi 1–x M x O 2 , M = metals), Li-rich (Li 1+x Mn y M 1–x–y O 2 ), and high-voltage spinel (LiMn 1.5 Ni 0.5 O 4 ) electrodes with time-of-flight secondary ion mass spectrometry (TOF-SIMS) and X-ray photoelectron spectroscopy in conjunction with electrochemical techniques to better understand their evolving cathode–electrolyte interphase structure during cycling. TOF-SIMS provides fragment-specific information regarding the surface film content for each of the electrodes. High-Ni cathodes show thick surface films initially containing Li 2 CO 3 , later developing oxidized organic carbonates throughout cycling. Li-rich electrode surface films develop strong characteristics during their first activation cycles, where released O 2 oxidizes organic carbonates to form polymeric carbons and decomposes LiPF 6 . High-voltage spinel electrodes operate outside the standard electrolyte stability window, generating reactive oxidized electrolyte species that further decompose LiPF 6 . The distribution and concentration of these different chemical fragments measured by TOF-SIMS are finally summarized by color-coded high-resolution images of cycled high-Ni, Li-rich, and high-voltage spinel electrodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Pressure-Tolerant 3D Anodes Enable Short-Circuit Prevention and Low Heat Generation in Argyrodite Solid-State Batteries

Solid-state batteries (SSBs) offer a safer, higher-energy-density alternative to lithium-ion batteries, yet commercialization is hindered by incompatibility with lithium metal. Here, to overcome these challenges, we developed a cost-effective, commercially available prelithiated micro carbon fiber framework (Li-Cf) anode featuring a high-pressure-tolerance, for use with argyrodite solid-state electrolytes (SSEs). This 3D structure accommodates uniform lithium deposition, simplifies cell assembly under elevated pressure, inhibits dendrite growth toward SSEs, reduces heat generation, and enhances overall compatibility. Notably, our architecture enables the cell to tolerate pressures up to 400 MPa without short-circuiting during assembly. Meanwhile, the 3D framework serves as a preferential pathway for lithium deposition, thereby reducing lithium growth toward the SSEs and mitigating the risk of dendrite formation in SSEs. Operando calorimetry and distribution of relaxation times analysis reveal that lithium morphology degradation at the interface with the SSEs is a key failure mechanism in lithium metal argyrodite SSBs, leading to increased diffusion resistance and heat generation. In contrast, the Li-Cf anode mitigates these issues by reducing both heat flux and charge transfer resistance. Full cells with LiNi 0.8 Co 0.1 Mn 0.1 O 2 /Li 6 PS 5 Cl/Li-Cf retain ~79% capacity after 600 cycles, demonstrating significantly improved cycling stability and strong potential for practical energy storage applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Operando Analysis of Gas Evolution in TiNb 2 O 7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb 2 O 7 (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. Furthermore, this enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO 2 , C 2 H 4 , and O 2 . A solid–electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO 2 and C 2 H 4 evolution by ~2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Mission Analysis for Marine Renewable Energy to Provide Power for Marine Carbon Dioxide Removal

The mission of this project was to provide a preliminary feasibility assessment of powering different marine carbon dioxide removal (mCDR), marine carbon capture, and marine carbon sequestration strategies with marine energy. In this report, carbon capture refers to methods that can separate or capture carbon dioxide (CO 2 ) from the air or ocean; carbon sequestration refers to methods that store CO 2 obtained by capture methods out of the atmosphere for long periods of time; and carbon dioxide removal (CDR) refers to methods that do both. The project found that mCDR powered by marine energy and offshore wind energy available in the United States could meet global CDR scales needed by 2040 and 2050 to limit warming to 1.5 degrees C by 2100. Note that this preliminary estimate assumes that it is possible to harvest all the marine and offshore wind resources available in the United States with existing technology options, and it does not account for the power needed for monitoring these methods, as these power needs are not yet well defined and require further research. Additionally, these CDR scales will still require emissions reductions.

16 TIDAL AND WAVE POWER↗
DOE OSTI2025

Kinetic Investigation by Batch Processing of Film Growth during the Electrodeposition of Titanium from Ethaline

Titanium electrodeposition as a technological advance has been out of reach due to the poor film quality obtained when using previously developed methods. This study shows that the electrodeposition of Ti is possible and feasible from the deep eutectic solvent ethaline. Moreover, this study shows through batch analysis that this deposition has temperature-dependent aspects that alter the film deposition kinetics upon modest heating. This ultraviolet–visible spectroscopic study is highlighting the more facile reduction of Ti 4+ to Ti 3+ and then to Ti 2+ at elevated temperatures. Understanding the underlying kinetics of electrodeposition opens up new venues for the application of this important metal.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanistic Insight into Lignin Slow Pyrolysis by Linking Pyrolysis Chemistry and Carbon Material Properties

As a highly abundant renewable carbon source, lignin can be converted to a variety of advanced carbon materials with tailorable properties through slow pyrolysis. In this study, slow pyrolysis of kraft lignin, for the first time, was investigated with a commercial pyrolysis–gas chromatography–mass spectrometry (Py–GC–MS) system through evolved gas analysis-MS (EGA-MS) and heart-cutting-GC–MS (HC-GC–MS) analyses. These analyses allow recovery and examination of the multiphased gas products generated from thermal decomposition of lignin during slow pyrolysis at a controlled heating rate over a long time course, thus making it possible to link operation conditions, pyrolysis chemistry, and carbon material properties. The overall product distributions, including volatiles and solid products, were quantitatively tracked at different heating rates (2, 20, and 40 °C/min) and different temperature regions (100–200, 200–300, and 300–600 °C). Solid residues were further characterized using a suite of analytical tools, in correlation with the investigation of formation mechanisms of volatiles to reveal the reaction chemistry of lignin during slow pyrolysis and to determine the morphology, pore structure, and interfacial chemical properties. This study provides critical insights into the slow pyrolysis chemistry of lignin and the properties of the resulting carbon material. These results will facilitate a better design and control of the lignin slow pyrolysis process for synthesizing functional carbon materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗