Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Ablative overlays for Space Shuttle leading edge ascent heat protection

Ablative overlays were evaluated via a plasma-arc simulation of the ascent pulse on the leading edge of the Space Shuttle Orbiter. Overlay concepts included corkboard, polyisocyanurate foam, low-density Teflon, epoxy, and subliming salts. Their densities ranged from 4.9 to 81 lb per cu ft, and the thicknesses varied from 0.107 to 0.330 in. Swept-leading-edge models were fabricated from 30-lb per cu ft silicone-based ablators. The overlays were bonded to maintain the surface temperature of the base ablator below 500 F during ascent. Foams provided minimum-weight overlays, and subliming salts provided minimum-thickness overlays. Teflon left the most uniform surface after ascent heating.

Strauss, E. L.↗
NASA NTRS1975

Flow rates for sharp-edged orifices

Two charts are proposed for calculating the flow coefficient and the area correction factor used in the equation for the flow rate through a sharp-edged orifice. The proposed charts account for variations in the discharge coefficient of sharp-edged orifices and can be used with any pressure ratio for both subcritical and supercritical flow conditions. They can also be used for any gas by using the appropriate gas constant and ratio of specific heats. The application of the charts is illustrated by examples.

Groesbeck, W. A.↗
NASA NTRS1976

Wind-tunnel investigation of control-surface characteristics. 5: The use of a beveled trailing edge to reduce the hinge moment of a control surface

Wind tunnel tests have been made to investigate the possibility of reducing the hinge moments of a control surface by beveling the trailing edge. The tests were made with a 9 percent thick airfoil having a 30 percent chord plain flap. A faired beveled shape, 5 percent of the airfoil chord in width and having a thickness of 21/2 percent of the airfoil chord, was found to give approximately 50 percent reduction in the hinge moment caused by a given deflection of the flap and 80 percent reduction in the hinge moment due to the angle of attack of this airfoil for a wide range of angles. Elliptical trailing edge shapes were also tried but were found to be somewhat less effective.

Jones, R. T.↗
NASA NTRS1976

Static force tests of a sharp leading edge delta-wing model at ambient and cryogenic temperatures with a description of the apparatus employed

A sharp leading edge delta-wing model was tested through an angle-of-attack range at Mach numbers of 0.75, 0.80, and 0.85 at both ambient and cryogenic temperatures in the Langley 1/3-meter transonic cryogenic tunnel. Total pressure was varied with total temperature in order to hold test Reynolds number constant at a given Mach number. Agreement between the aerodynamic data obtained at ambient and cryogenic temperatures indicates that flows with leading-edge vortex effects are duplicated properly at cryogenic temperatures. The test results demonstrate that accurate aerodynamic data can be obtained by using conventional force-testing techniques if suitable measures are taken to minimize temperature gradients across the balance and to keep the balance at ambient (warm) temperatures during cryogenic operation of the tunnel.

Kilgore, R. A.↗
NASA NTRS1976

The Effects of Blowing Over Various Trailing-edge Flaps on an NACA 0006 Airfoil Section, Comparisons with Various Types of Flaps on other Airfoil Sections, and an Analysis of Flow and Power Relationships for Blowing Systems

The results are presented of a two-dimensional investigation conducted to determine the effect of blowing over various types of trailing-edge flaps on a wing having the NACA 0006 airfoil section and a drooped-nose flap. The position and profile of the trailing-edge flap, the nozzle height, and the location of the flap with respect to the nozzle were found to be important variables. Data from many investigations were used to make an evaluation of the effects of blowing on lift. An analysis was made of flow and power relationships for blowing systems.

Dods, J. B., Jr.↗
NASA NTRS1975

Hypersonic incipient separation on delta wing with trailing-edge flap

The paper reviews the experimental data on the incipient separation characteristics of planar delta wings of 75 degree sharp leading edges, with full-span trailing edge flap deflected into the windward flow. The local Reynolds number range for these investigations covered laminar, transitional and turbulent conditions. It is shown that, while turbulent boundary layer data correlates with two dimensional results, in the laminar and transitional cases, there is a nearly parallel shift to higher flap angles for incipient separation.

Rao, D. M.↗
NASA NTRS1976

On thermal edge effects in composite laminates

Results are presented for a finite-element investigation of the combined influence of edge effects due to mechanical and thermal mismatch in composite laminates with free edges. Laminates of unidirectional boron/epoxy symmetrically bonded to sheets of aluminum and titanium were studied. It is shown that interlaminar thermal stresses may be more significant than the interlaminar stresses due to loading only. In addition, the stresses due to thermal mismatch may be of the same sign as those due to Poisson's mismatch or they may be of opposite sign depending upon material properties, stacking sequence, and direction of loading. The paper concludes with a brief discussion of thermal stresses in all-composite laminates.

Herakovich, C. T.↗
NASA NTRS1977

Extruded edge members for honeycombs

Edge members in bonded honeycomb panel structures are conventionally made by machining channels in aluminum bars. Open ends are stuffed with honeycomb core, using intumescent adhesive. Less expensive technique eliminates need for stuffing. Extended edges are more reliable, lighter, and easier to install. New manufacturing method may prove useful in fabricating structures such as air-frames, recreational-vehicle frame members, and the like in which weight savings is primary goal.

Haskell, D. R.↗
NASA NTRS1976

Computer simulation and evaluation of edge detection algorithms and their application to automatic path selection

The construction of an autonomous roving vehicle requires the development of complex data-acquisition and processing systems, which determine the path along which the vehicle travels. Thus, a vehicle must possess algorithms which can (1) reliably detect obstacles by processing sensor data, (2) maintain a constantly updated model of its surroundings, and (3) direct its immediate actions to further a long range plan. The first function consisted of obstacle recognition. Obstacles may be identified by the use of edge detection techniques. Therefore, the Kalman Filter was implemented as part of a large scale computer simulation of the Mars Rover. The second function consisted of modeling the environment. The obstacle must be reconstructed from its edges, and the vast amount of data must be organized in a readily retrievable form. Therefore, a Terrain Modeller was developed which assembled and maintained a rectangular grid map of the planet. The third function consisted of directing the vehicle's actions.

Longendorfer, B. A.↗
NASA NTRS1977

Analysis of the separated boundary layer flow on the surface and in the wake of blunt trailing edge airfoils

The viscous flow phenomena associated with sharp and blunt trailing edge airfoils were investigated. Experimental measurements were obtained for a 17 percent thick, high performance GAW-1 airfoil. Experimental measurements consist of velocity and static pressure profiles which were obtained by the use of forward and reverse total pressure probes and disc type static pressure probes over the surface and in the wake of sharp and blunt trailing edge airfoils. Measurements of the upper surface boundary layer were obtained in both the attached and separated flow regions. In addition, static pressure data were acquired, and skin friction on the airfoil upper surface was measured with a specially constructed device. Comparison of the viscous flow data with data previously obtained elsewhere indicates reasonable agreement in the attached flow region. In the separated flow region, considerable differences exist between these two sets of measurements.

Goradia, S. H.↗
NASA NTRS1977

Subsonic longitudinal aerodynamic characteristics of a vectored-engine-over-wing configuration having spanwise leading-edge vortex enhancement

A configuration which integrates a close coupled canard wing combination, spanwise blowing for enhancement of the wing leading edge vortex, an engine-over-wing concept, and a wing trailing edge coanda-effect flap is studied. The data on the configuration are presented in tabular from without discussion. The investigation was conducted in the Langley 7- by 10-foot high speed tunnel at a Mach number of 0.166 through an angle-of-attack range from -2 to 22 deg. Rectangular main engine nozzles of aspect ratio 4, 6, and 8 were tested over a momentum coefficient range from 1.0 to 1.8.

Huffman, J. K.↗
NASA NTRS1976

A fractographic study of the edge-sliding mode in fracture toughness testing

A fractographic study of Mode II fracture surfaces has been conducted for the purpose of identifying the microstructural mechanisms responsible for fracture in the edge-sliding mode. A compact shear (CS) specimen was employed to generate the fracture surfaces and also to establish Mode II fracture toughness values for Ti-6Al-4V, A533-B steel, and several aluminum alloys. In all tests, one of the two edge cracks sustained complete Mode II fracture while the other exhibited only a limited amount of subcritical crack growth. Mode II fracture surfaces, which were unique in appearance, have been examined by optical and scanning electron microscopy. It was determined that shear (or parabolic) microvoid coalescence was the dominant mechanism for Mode II fracture. It was also established that most of the surface abrasions were created by the relative sliding of the fracture surfaces during unstable fracture rather than the crack initiation process.

Jones, D. L.↗
NASA NTRS1977

On the 'edge-on' configuration of the nuclei of comet West /1975n/

Observations made when earth crossed the orbital plane of comet West in 1976, providing an 'edge-on' view of the multiple nucleus, are used to calculate improved orbital elements for nucleus A at the time of crossing, for nucleus B relative to A and to D, and for nucleus D relative to A. The results appear to confirm that the motions of the fragments normal to the orbital plane were rather insignificant. Difficulties created by this finding for the solar-attraction theory on the rate of separation of split-comet fragments are discussed. The motion of a comet fragment off the orbital plane of the principal nucleus is analyzed in terms of both the initial-impulse and the nongravitational-acceleration hypotheses. Prospects for observing the nuclei of this comet at the next favorable edge-on projection (July 21, 1977) are evaluated.

Sekanina, Z.↗
NASA NTRS1977

A numerical study of the unsteady leading edge separation bubble on an oscillating airfoil

A preliminary study of the unsteady viscous flow in the region of an airfoil leading edge was performed, in which the interaction between the viscous and inviscid flow fields is neglected. The solution method uses the finite difference form of the governing equations throughout the separated flow field and incorporates a transition model based on the integral turbulence kinetic energy equation. The validity of the numerical procedure is verified by making comparisons with analytical solutions to several test problems, including unsteady flow over a plate oscillating in its own plane. The method was then applied to the problem of unsteady viscous flow over a NACA 0012 airfoil oscillating sinusoidally in pitch. The flow field characteristics were in qualitative agreement with experimental results. The bubble moved forward on the airfoil and decreased in size as incidence was increased. Viscous flow in the leading edge region was found to be quasi-steady, while bubble height varied inversely with Reynolds number.

Kreskovsky, J. P.↗
NASA NTRS1978

Edge geometry of turbomachine blades

Computer program calculates leading- and trailing-edge circle radii, tangency angles on leading- and trailing-edge circles, and stagger angle of turbomachinery blade sections, using only spline points defining blade surfaces.

Schumann, L. F.↗
NASA NTRS1978

Effect of leading-edge contour and vertical-tail configuration on the low-speed stability characteristics of a supersonic transport model having a highly-swept arrow wing

A low-speed investigation was made on a highly-swept arrow-wing model to determine the effect of wing leading-edge contour and vertical-tail configuration on the aerodynamic characteristics in pitch and sideslip. The investigation was made with the trailing-edge flaps deflected over a range of angles of attack from 8 deg to 32 deg. The tests were made at a Mach number of 0.13, which corresponds to a Reynolds number of about 3,000,000 based on the wing reference chord.

Lockwood, V. E.↗
NASA NTRS1978

A review of the theory of trailing edge noise

Literature on the theory of the generation of sound by the interaction of low Mach number turbulent flow with the edge of a semi-infinite rigid plate is critically reviewed. Three different approaches to the subject are identified, consisting of theories based on (1) Lighthill's acoustic analogy; (2) the solution of special, linearized hydroacoustic problems; and (3) ad hoc aerodynamic source models. When appropriately interpreted, all relevant theories produce essentially identical predictions in the limit of very small Mach numbers. None of the theories discusses the implications of the Kutta condition, however, nor of the effect of forward flight and source motion relative to the trailing edge. An outline of a redevelopment of the theory is included to give a unified view of the problem, exhibit the significance of the various approximations, and incorporate the effect of mean motion and of the Kutta condition.

Howe, M. S.↗
NASA NTRS1978

Effects of wing leading-edge deflection on the low-speed aerodynamic characteristics of a low-aspect-ratio highly swept arrow-wing configuration

Wing leading-edge deflection effects on the low-speed aerodynamic characteristics of a low-aspect-ratio highly swept arrow-wing configuration were determined. Static force tests were conducted in a V/STOL tunnel at a Reynolds number of about 2.5 x 1 million for an angle-of-attack range from -10 deg to 17 deg and an angle-of-sideslip range from -5 deg to 5 deg. Limited flow visualization studies were also conducted in order to provide a qualitative assessment of leading-edge upwash characteristics.

Coe, P. L., Jr.↗