Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICON OXIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Heavy carbon in individual oxide grains from the Murchison meteorite

The carbon isotopic composition of individual oxide grains from Murchison HF-HCl acid residue CFOc has been measured in the ion microprobe. Many grains contain carbon with large C-13 excesses ranging to 7000 per mil. In most cases the carbon is present as micron-sized subgrains. The association of silicon with the anomalous carbon points towards SiC as carrier. If this tentative identification is correct, then the SIC grains most likely originated in the circumstellar atmospheres of red giants. Oxide grains in which the O-18/O-16 ratio has also been measured show variable O-16 excesses which are not correlated with the C-13 excesses. This indicates that the sources of the anomalous carbon and oxygen isotopic compositions of the oxide grains are unrelated.

Zinner, Ernst↗
NASA NTRS1987

Resistivity and thickness effects in dendritic web silicon solar cells

The decrease of minority carrier lifetime as resistivity decreases in dendritic-web silicon solar cells is addressed. This variation is shown to be consistent with the presence of defect levels in the bandgap which arise from extended defects in the web material. The extended defects are oxide precipitates (SiOx) and the dislocation cores they decorate. Sensitivity to this background distribution of defect levels increases with doping because the Fermi level moves closer to the majority carrier band edge. For high-resistivity dendritic-web silicon, which has a low concentration of these extended defects, cell efficiencies as high as 16.6 percent (4 sq cm, 40 ohm-cm boron-doped base, AM1.5 global, 100 mW/sq cm, 25 C JPL LAPSS1 measurement) and a corresponding electron lifetime of 38 microsec have been obtained. Thickness effects occur in bifacial cell designs and in designs which use light trapping. In some cases, the dislocation/precipitate defect can be passivated through the full thickness of web cells by hydrogen ion implantation.

Meier, D. L.↗
NASA NTRS1985

Oxidation resistant slurry coating for carbon-based materials

An oxidation resistant coating is produced on carbon-base materials, and the same processing step effects an infiltration of the substrate with silicon containing material. The process comprises making a slurry of nickel and silicon powders in a nitrocellulose lacquer, spraying onto the graphite or carbon-carbon substrate, and sintering in vacuum to form a fused coating that wets and covers the surface as well as penetrates into the pores of the substrate. Optimum wetting and infiltration occurs in the range of Ni-60 w/o Si to Ni-90 w/o Si with deposited thicknesses of 25-100 mg/sq. cm. Sintering temperatures of about 1200 C to about 1400 C are used, depending on the melting point of the specific coating composition. The sintered coating results in Ni-Si intermetallic phases and SiC, both of which are highly oxidation resistant.

Smialek, J. L.↗
NASA NTRS1986

On the sintering of silicon carbide

This document deals with the sintering of silicon carbide using pressureless sintering. This technique makes it possible to sinter a primarily covalent material to usable densities up to over 98% thD without having to use a high amount of sinter additives as is the case with other non-oxide ceramic materials. The process takes place rapidly, and it is also possible to produce relatively thick-walled structural parts without major problems. This sheds more light on the true characteristics of silicon carbide in one structural part, since there is no second or nearly no second phase. Heat pressing has improved stability.

Gugel, E.↗
NASA NTRS1987

Friction and wear behaviour of ion beam modified ceramics

In the present study, the sliding friction coefficients and wear rates of carbide, oxide, and nitride materials for potential use as sliding seals (ring/liner) were measured under temperature, environmental, velocity, and loading conditions representative of a diesel engine. In addition, silicon nitride and partially stabilized zirconia discs were modified by ion mixing with TiNi, nickel, cobalt and chromium, and subsequently run against carbide pins, with the objective of producing reduced friction via solid lubrication at elevated temperature. Unmodified ceramic sliding couples were characterized at all temperatures by friction coefficients of 0.24 and above. However, the coefficient at 800 C in an oxidizing environment was reduced to below 0.1, for certain material combinations, by the ion implantation of TiNi or cobalt. This beneficial effect was found to derive from lubricious titanium, nickel, and cobalt oxides.

Lankford, J.↗
DOE OSTI2021

Efficient passivation of n-type and p-type silicon surface defects by hydrogen sulfide gas reaction

An efficient surface defect passivation is observed by reacting clean Si in a dilute hydrogen sulfide-argon gas mixture (< 5% H2S in Ar) for both n-type and p-type Si wafers with planar and textured surfaces. Surface recombination velocities of 1.5 and 8 cm/s are achieved on n-type and p-type Si wafers, respectively, at an optimum reaction temperature of 550oC that are comparable to the best surface passivation quality used in high efficiency Si solar cells. Surface chemical analysis using x-ray photoelectron spectroscopy shows that sulfur is primarily bonded in a sulfide environment, and synchrotron-based soft x-ray emission spectroscopy of the adsorbed sulfur atoms suggests the formation of S-Si bonds. Furthermore, the sulfur surface passivation layer is unstable in air, attributed to surface oxide formation and a simultaneous decrease of sulfide bonds. However, the passivation can be stabilized by a low-temperature (300oC) deposited amorphous silicon nitride (a-Si:NX:H) capping layer.

14 SOLAR ENERGY↗
NASA NTRS2003

From Oxygen Generation to Metals Production: In Situ Resource Utilization by Molten Oxide Electrolysis

For the exploration of other bodies in the solar system, electrochemical processing is arguably the most versatile technology for conversion of local resources into usable commodities: by electrolysis one can, in principle, produce (1) breathable oxygen, (2) silicon for the fabrication of solar cells, (3) various reactive metals for use as electrodes in advanced storage batteries, and (4) structural metals such as steel and aluminum. Even so, to date there has been no sustained effort to develop such processes, in part due to the inadequacy of the database. The objective here is to identify chemistries capable of sustaining molten oxide electrolysis in the cited applications and to examine the behavior of laboratory-scale cells designed to generate oxygen and to produce metal. The basic research includes the study of the underlying high-temperature physical chemistry of oxide melts representative of lunar regolith and of Martian soil. To move beyond empirical approaches to process development, the thermodynamic and transport properties of oxide melts are being studied to help set the limits of composition and temperature for the processing trials conducted in laboratory-scale electrolysis cells. The goal of this investigation is to deliver a working prototype cell that can use lunar regolith and Martian soil to produce breathable oxygen along with metal by-product. Additionally, the process can be generalized to permit adaptation to accommodate different feedstock chemistries, such as those that will be encountered on other bodies in the solar system. The expected results of this research include: (1) the identification of appropriate electrolyte chemistries; (2) the selection of candidate anode and cathode materials compatible with electrolytes named above; and (3) performance data from a laboratory-scale cell producing oxygen and metal. On the strength of these results it should be possible to assess the technical viability of molten oxide electrolysis for in situ resource utilization on the Moon and Mars. In parallel, there may be commercial applications here on earth, such as new green technologies for metals extraction and for treatment of hazardous waste, e.g., fixing heavy metals.

Khetpal, Deepak↗
NASA NTRS2003

Silicon Carbide Fiber-Reinforced Silicon Nitride Composites

The fabrication and thermo-mechanical properties of SiC monofilament- and SiC fiber tow-reinforced reaction-bonded silicon nitride matrix composites (SiC/RBSN) and fully dense SiC monofilament-reinforced silicon nitride matrix composites (SiC/Si3N4) have been reviewed. The SiC/RBSN composites display high strength and toughness, and low thermal conductivity in the as-fabricated condition, but are susceptible to internal oxidation and mechanical property degradation in the intermediate temperature range from 400 to 1100 C. The internal oxidation problem can be avoided by applying functionally graded oxidation resistant coatings on external surfaces of the composite. On the other hand, the fully dense SiC/SiC3N4 composites fabricated by using SiC monofilaments and pressure assisted sintering methods display moderate strength and limited strain capability beyond matrix cracking stress. Advantages, disadvantages, and potential applications of SiC fiber-reinforced silicon nitride matrix composites fabricated using various fiber types and processing methods are discussed.

Bhatt, Ramakrishna T.↗
DOE OSTI2022

Control of High-Temperature Static and Transient Thermomechanical Behavior of SiMo Ductile Iron by Al Alloying

Abstract Silicon and molybdenum ( SiMo ) ductile iron is commonly used for exhaust manifolds because these components experience thermal cycling in oxidizing environment, which requires resistance to fatigue during transient thermomechanical loads. Previous studies have demonstrated that alloying elements, such as Al , to SiMo ductile iron reduces the amount of surface degradation during static high-temperature exposure. However, deterioration of sphericity of the graphite nodules and a decrease in ductility could affect the tendency of cracking during thermal cycling. In this article, the effect of Al alloying on static and transient thermomechanical behavior of SiMo ductile iron was investigated to optimize the amount of Al alloying. A thermodynamic approach was used to confirm the effect of the Al alloying on the phase transformations in two SiMo cast irons, alloyed by 1.8% Al and 3% Al . These two alloys were cast in a laboratory along with the baseline SiMo ductile iron. Several experimental methods were used to evaluate the dimensional stability, physical properties, static oxidation, and failure resistance during constrained thermal cycling testing to compare their high-temperature capability. Experimental results verified that Al alloying increases the temperature range and decreases volume change during eutectoid transformation, which together with enhancement of oxidation protection improved the dimensional stability. Thermocycling tests showed that the number of cycles to failure depends on the amount of Al alloying and the applied high-temperature exposure during each cycle. SEM/EDX, high-resolution TEM and µCT analysis were used to verify the mechanism resulting from the Al alloying protection. It was shown that an optimal level of Al alloying for balancing oxidation and thermal cracking resistance depends on thermomechanical conditions of application.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Surface Reconstruction in Hydrated Amphiphilic Block Copolymer Thin Films Probed by Fluid Cell Atomic Force Microscopy

In many thin film materials, nuanced interplays of interfacial energies control the surface morphology and rearrangement. This work evaluates polymer−solvent interactions and solvent-driven surface reconstructions via ex situ and in situ fluid cell Atomic Force Microscopy (fc-AFM) analysis of amphiphilic block copolymer (BCP) thin films upon exposure to deionized (DI) water. We examine the differences in surface morphology, whole-film swelling, and force response in thin films of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) and polystyrene- block-poly[(allyl glycidyl ether)-co-(ethylene oxide)] (PS-b- P[AGE-co-EO]) processed into standing-up cylinder morphologies perpendicular to a silicon substrate (⊥C). Using Amplitude Modulation AFM (AM-AFM) and Amplitude-Phase Distance (APD) force spectroscopy, this work probes the mechanoresponsive nature of the dynamic surface layers of these films, unveiling surface layer stratification and surface chain rearrangement via minimal tip−sample stimulation. To help rationalize the observed reconfigurations, the energetic driving forces were estimated using the harmonic mean approximations of interfacial energies. Given the nonionizable nature of the minority P(AGE-co-EO) block and the energetic driving forces for chain mobility, this work shows how the elimination of unfavorable PS−water interfaces drives chain rearrangement and coverage of the PS surface by chains of the hydrophilic block. This work highlights considerations for increasing the heterogeneity and complexity of BCP thin films via random blocks and how those changes to local interfacial energies may drive larger scale film morphology reconstructions, with broader implications for tuning interface hydrophilicity.

Copolymers↗
DOE OSTI2022

High-resolution Compton spectroscopy using x-ray microcalorimeters

X-ray Compton spectroscopy is one of the few direct probes of the electron momentum distribution of bulk materials in ambient and operando environments. Herein, we report high-resolution inelastic x-ray scattering experiments with high momentum and energy transfer performed at a storage-ring-based high-energy x-ray light source facility using an x-ray transition-edge sensor (TES) microcalorimeter detector. The performance was compared with a silicon drift detector (SDD), an energy-resolving semiconductor detector, and Compton profiles were measured for lithium and cobalt oxide powders relevant to lithium-ion battery research. Spectroscopic analysis of the measured Compton profiles demonstrates the high-sensitivity to the low- Z elements and oxidation states. The line shape analysis of the measured Compton profiles in comparison with computed Hartree–Fock profiles is usually limited by the resolution of the semiconductor detector. We have characterized an x-ray TES microcalorimeter detector for high-resolution Compton scattering experiments using a bending magnet source at the Advanced Photon Source with a double crystal monochromator, providing monochromatic photon energies near 27.5 keV. The momentum resolution below 0.16 atomic units (a.u.) was measured, yielding an improvement of more than a factor of 7 over a state-of-the-art SDD for the same scattering geometry. Furthermore, the lineshapes of narrow valence and broad core electron profiles of sealed lithium metal were clearly resolved using an x-ray TES compared to smeared and broadened lineshapes observed when using the SDD. High-resolution Compton scattering using the energy-resolving area detector shown here presents new opportunities for spatial imaging of electron momentum distributions for a wide class of materials with applications ranging from electrochemistry to condensed matter physics.

47 OTHER INSTRUMENTATION↗
NASA NTRS1979

Fibrous refractory composite insulation

A refractory composite insulating material was prepared from silica fibers and aluminosilicate fibers in a weight ratio ranging from 1:19 to 19:1, and about 0.5 to 30% boron oxide, based on the total fiber weight. The aluminosilicate fiber and boron oxide requirements may be satisfied by using aluminoborosilicate fibers and, in such instances, additional free boron oxide may be incorporated in the mix up to the 30% limit. Small quantities of refractory opacifiers, such as silicon carbide, may be also added. The composites just described are characterized by the absence of a nonfibrous matrix.

Leiser, D. B.↗
NASA NTRS1981

CADAT field-effect-transistor simulator

CADAT field-effect transistor simulator (FETSIM) analyzes dc and transient behavior of metal-oxide-semiconductor (MOS) circuits. Both N-MOS and P-MOS transistor configurations in either bulk of silicon-on-sapphire (SOS) technology and almost any combination of R/C elements are analyzed.

Source record↗
NASA NTRS1990

MCT/MOSFET Switch

Metal-oxide/semiconductor-controlled thyristor (MCT) and metal-oxide/semiconductor field-effect transistor (MOSFET) connected in switching circuit to obtain better performance. Offers high utilization of silicon, low forward voltage drop during "on" period of operating cycle, fast turnon and turnoff, and large turnoff safe operating area. Includes ability to operate at high temperatures, high static blocking voltage, and ease of drive.

Rippel, Wally E.↗
NASA NTRS1990

Optical property measurements as a diagnostic tool for control of materials processing in space and on Earth

A new method is described, including results, to measure, control, and follow containerless processing in ground based levitators. This technique enables instantaneous optical property measurements from a transient solid or liquid surface concurrent with true temperature measurement. This was used successfully as a diagnostic tool to follow processing of Al, Si, and Ti during electromagnetic levitation. Experiments on Al show the disappearance of the oxide (emittance 0.33) at ca. 1300 C leaving a liquid surface with an emittance of 0.06. Electromagnetic levitation of silicon shows a liquid with a constant emittance (0.2) but with a solid whose emittance decreases very rapidly with increasing temperature. Consequently, the processing of materials at high temperatures can be controlled quite well through the control of surface optical properties.

Krishnan, Shankar↗
NASA NTRS2000

Reliable, Low-Cost, Low-Weight, Non-Hermetic Coating for MCM Applications

Through an Air Force Research Laboratory sponsored STM program, reliable, low-cost, low-weight, non-hermetic coatings for multi-chip-module(MCK applications were developed. Using the combination of Sandia Laboratory ATC-01 test chips, AvanTeco's moisture sensor chips(MSC's), and silicon slices, we have shown that organic and organic/inorganic overcoatings are reliable and practical non-hermetic moisture and oxidation barriers. The use of the MSC and unpassivated ATC-01 test chips provided rapid test results and comparison of moisture barrier quality of the overcoatings. The organic coatings studied were Parylene and Cyclotene. The inorganic coatings were Al2O3 and SiO2. The choice of coating(s) is dependent on the environment that the device(s) will be exposed to. We have defined four(4) classes of environments: Class I(moderate temperature/moderate humidity). Class H(high temperature/moderate humidity). Class III(moderate temperature/high humidity). Class IV(high temperature/high humidity). By subjecting the components to adhesion, FTIR, temperature-humidity(TH), pressure cooker(PCT), and electrical tests, we have determined that it is possible to reduce failures 50-70% for organic/inorganic coated components compared to organic coated components. All materials and equipment used are readily available commercially or are standard in most semiconductor fabrication lines. It is estimated that production cost for the developed technology would range from $1-10/module, compared to $20-200 for hermetically sealed packages.

Jones, Eric W.↗
NASA NTRS2002

Measurements of Optically Transparent and Mirrored Specimens from the POSA and EOIM III Space Flight Experiments

A selected set of optically transparent specimens and first surface mirror specimens have been examined subsequent to on-orbit exposure. Certain specimens were from the Passive Optical Sample Assembly I and II experiments flown on the MIR Space Station. Other specimens were from the Energetic Oxygen Interaction with materials III experiment flown on the STS in August 1992. A comparison of pre- and post-flight transmission of reflectance measurements, as appropriate, has been carried out. Data from different specimens includes results of measurements for IR, optical, UV and/or vacuum UV wavelength intervals. Results of these measurements clearly show the effects of molecular contamination deposits on the surfaces during the on-orbit exposures. Surface analysis on a attracted set of specimens provides and estimate of contaminant thickness and composition and provides an insight into on-orbit deposition rates and surface oxidation reactions. For both the EOIM III and POSA I & II experiments, the primary source of contamination were outgassed silicones. Both experiments received approximately the same fluence of atomic oxygen (approx. 1-2 x 1020 atoms per square centimeter). ROSA specimens received between approx. 400 and 580 equivalent sun hours (ESH) of solar radiation over an 18 month period in orbit. The EOIM specimens were on an STS flight of about 1 week duration and received only approx. 5-10 ESH of solar radiation.

Pippin, Gary↗
NASA NTRS2004

Microstructural Optimization of High Temperature SiC/SiC Composites

Advanced materials and process approaches are described that have allowed NASA to develop five state-of-the-art silicon carbide (SiC) fiber-reinforced hybrid-SiC matrix composite systems that can operate under mechanical loading and oxidizing conditions for hundreds of hours at upper use temperatures from 1200 to 1450 C. Key data are presented that demonstrate the ability of these materials to meet the first-level property requirements for hot-section components in advanced gas turbine engines.

DiCarlo, James A.↗