Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additive manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

System and method for high power diode based additive manufacturing

A system is disclosed for performing an Additive Manufacturing (AM) fabrication process on a powdered material forming a substrate. The system may make use of a diode array for generating an optical signal sufficient to melt a powdered material of the substrate. A mask may be used for preventing a first predetermined portion of the optical signal from reaching the substrate, while allowing a second predetermined portion to reach the substrate. At least one processor may be used for controlling an output of the diode array.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Reinforcement Learning for Generating Toolpaths in Additive Manufacturing

Generating toolpaths plays a key role in additive manufacturing processes. In the case of 3-Dimensional (3D) printing, these toolpaths are the pathways the printhead will follow to fabricate a part in a layer-by-layer fashion. Most toolpath generators use nearest neighbor (NN), branch-and-bound, or linear programming algorithms to produce valid toolpaths. These algorithms often produce sub-optimal results or cannot handle large sets of traveling points. In this paper, the researchers at Oak Ridge National Laboratory’s (ORNL) Manufacturing Demonstration Facility (MDF) propose using a machine learning (ML) approach called reinforcement learning (RL) to produce toolpaths for a print. RL is the process of two agents, the player and the critic, learning how to maximize a score based upon the actions of the player in a defined state space. In the context of 3D printing, the player will learn how to find the optimal toolpath that reduces printhead lifts and global print time.

Patrick, Steven↗
DOE OSTI2020

System and method for high power diode based additive manufacturing

A system is disclosed for performing an Additive Manufacturing (AM) fabrication process on a powdered material forming a substrate. The system may make use of a diode array for generating an optical signal sufficient to melt a powdered material of the substrate. A mask may be used for preventing a first predetermined portion of the optical signal from reaching the substrate, while allowing a second predetermined portion to reach the substrate. At least one processor may be used for controlling an output of the diode array.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Additive manufacturing system and method having toolpath analysis

An additive manufacturing (AM) system is disclosed for constructing a three dimensional (3D) part with optimized orthotropy. The system combines an electronic processor which calculates an optimal set of physically achievable toolpaths to meet a given design objective, and a 3D printing direct ink write machine capable of printing inks with reinforcing particles that result in orthotropic materials. The electronic processor may combine a Domain of Interest subsystem that transforms a mathematical description of a desired part orthotropy to a plurality of guidepaths, a toolpath generate subsystem that develops a plurality of physically realizable toolpaths from those guidepaths with a minimum number of starts and stops, a finite element subsystem that computes spatially varying material orthotropy from those toolpaths and then solves a boundary value problem to determine a figure of merit for the design, and an optimization subsystem that uses that figure of merit to update the mathematical description of the part orthotropy to iteratively develop an improved part. The optimization subsystem also includes convergence criteria to indicate when toolpaths have been achieved that yield a sufficiently optimal part has been achieved. The toolpath generate can then output the final toolpaths, which are converted to suitable code that controls the motion of the 3D printer toolhead and allows the optimized 3D part to be manufactured.

King, Michael J.↗
DOE OSTI2022

System and method for sub micron additive manufacturing

An apparatus is disclosed for performing an additive manufacturing operation to form a structure by processing a photopolymer resist material. The apparatus may incorporate a laser for generating a laser beam, and a tunable mask for receiving the laser beam which has an optically dispersive element. The mask splits the laser beam into a plurality of emergent beams each having a subplurality of beamlets of varying or identical intensity, with each beamlet emerging from a unique subsection of illuminated regions of the mask. A collimator collimates at least one of the emergent beams to form a collimated beam. One or more focusing elements focuses the collimated beam into a focused beam which is projected as a focused image plane on or within the resist material. The focused beam simultaneously illuminates a layer of the resist material to process an entire layer in a parallel fashion.

Saha, Sourabh Kumar↗
DOE OSTI2023

Multimaterial powder bed patterning for additive manufacturing method

The present disclosure relates to an additive manufacturing system. In one embodiment the system makes use of a reservoir for holding a granular material feedstock. A nozzle is in communication with the reservoir for releasing the granular material feedstock in a controlled fashion from the reservoir to form at least one layer of a part. An excitation source is included for applying a signal which induces a controlled release of the granular material feedstock from the nozzle as needed, to pattern the granular material feedstock as necessary to form a layer of the part.

Dudukovic, Nikola↗
DOE OSTI2023

System and method for microwave volumetric additive manufacturing

The present disclosure relates to a volumetric additive manufacturing system for forming a structure from a volume of resin using microwave energy. The system makes use of an electronic controller and at least one beam forming algorithm accessible by the electronic controller for generating information relating to an amplitude and a time delay for forming a microwave signal, where the microwave signal will be used in irradiating a build volume, and where the build volume is formed by the volume of resin. A microwave signal generating subsystem is included which is responsive to the information generated by the beam forming algorithm, and which generates a microwave signal using the amplitude and the time delay determined by the beam forming algorithm. An antenna is used to receive the microwave signal and project the microwave signal as a microwave beam, in accordance with the amplitude and time delay, into the build volume to form the structure.

Mukherjee, Saptarshi↗
DOE OSTI2025

Automated design of an additive manufactured compact broadband antenna for plasma reflectometry

Broadband antennas operating in the gigahertz frequency range are regularly used for plasma reflectometry diagnostics. Due to a lack of space and unique diagnostic constraints, these antennas are often custom in design and frequency range. Recent advances in additive manufacturing of high temperature copper alloys allow for expanded freedom in design of these diagnostic antennas. In this work, a heuristic simulated annealing algorithm is used alongside 3-D finite element simulation to automate the design of a double ridged rectangular horn antenna for a reflectometry diagnostic on the DIII-D tokamak. Optimization of antenna performance given the design constraints results in a compact broadband (6-20+ GHz) antenna design. Measured transmission from the additively manufactured antenna matches simulation within reasonable error, and experimental plasma electron density profiles from the DIII-D high-field side scrape-off layer are shown.

Additive manufacturing↗
NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

Additive Manufacturing↗
DOE OSTI2024

Adamantine 1.0: A Thermomechanical Simulator for Additive Manufacturing

Adamantine is a thermomechanical simulation code that is written in C++ and built on top of deal.II (Arndt et al., 2023), p4est (Burstedde et al., 2011), ArborX (Lebrun-Grandié et al., 2020), Trilinos (The Trilinos Project Team, 2020), and Kokkos (Trott et al., 2022). Adamantine was developed with additive manufacturing in mind and it is particularly well adapted to simulate fused filament fabrication, directed energy deposition, and powder bed fusion. Adamantine employs the finite element method with adaptive mesh refinement to solve a nonlinear anisotropic heat equation, enabling support for various additive manufacturing processes. It can also perform elastoplastic and thermoelastoplastic simulations. It can handle materials in three distinct phases (solid, liquid, and powder) to accurately reflect the physical state during different stages of the manufacturing process. To enhance simulation accuracy, adamantine incorporates data assimilation techniques (Asch et al., 2016). This allows it to integrate experimental data from sensors like thermocouples and infrared (IR) cameras. This combined approach helps account for errors arising from input parameters, material properties, models, and numerical calculations, leading to more realistic simulations that reflect what occurs in a particular print.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The performance of additively manufactured Haynes 282 in supercritical CO 2

The use of supercritical carbon dioxide (sCO 2 ) as a working fluid is garnering interest in next generation power production systems due to the possibility of increased operational efficiencies and lower associated costs. Its implementation requires alloys with excellent high temperature strength and corrosion resistance, which makes Haynes 282® (H282) a suitable candidate. With increasing adoption of additive manufacturing (AM) in the energy industry, there is a need to investigate long-term sCO2 exposure on AM produced materials. Additively manufactured H282 (AM-H282) samples built using laser powder bed fusion in two different orientations were analyzed through imaging, gravimetric analysis, and room-temperature tensile testing before and after 1000-h exposure to CO 2 at 750 °C and 20 MPa. Performed imaging included observation of the sample surfaces and of the material bulk (cross sections) through means of Scanning Electron Microscopy (SEM) and optical microscopy. In comparison to wrought H282, it was found that the exposed material exhibited a similar Cr 2 O 3 oxide protective layer about 2 μm in thickness with additional top-surface TiO 2 oxide and carbon-rich precipitates. It was also similarly observed that internal oxidation was present but limited to a depth of 20 μm, and a 1–3 μm γ’ denuded region appeared to surround all internal and surface oxidation. Thermal aging effects were noted with the precipitation of needle-like structures in the γ/γ’ matrix and a coarsening of the γ’ precipitates from 28 nm to 73 nm. Mass measurements analyzing oxide precipitation revealed a larger increase compared to wrought, representing an approximate 20% difference. Tensile testing results showed similar behavior to wrought with a slight increase in yield strength and a large reduction in elongation in the exposed samples.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Analysis on Part Distortion and Residual Stress in Big Area Additive Manufacturing with Carbon Fiber-Reinforced Thermoplastic using Dehomogenization Technique

Part distortion and bottom surface warpage often occur in extrusion-based additive manufacturing. The undesirable deformations during the printing process are due to residual stresses caused by material shrinkage. Analysis on residual stress and deformation requires accurate thermo-mechanical material properties. Polymer composites reinforced with short fibers have intrinsic inhomogeneities with nonuniform fiber orientation. Therefore, homogenized macro properties may not accurately represent the progressive damage behavior or distortion. In this study, fiber orientations in Acrylonitrile Butadiene Styrene (ABS) reinforced with 20%wt carbon fiber are calculated using a de-homogenization technique. Thermal expansion coefficients in multiple directions are obtained from Thermo-Mechanical Analysis (TMA) tests. Temperature dependent stiffness is measured, and temperature dependent strength is estimated. Thermal conductivities in multiple directions and thermal capacity are measured. The calibrated thermo-mechanical properties of the composite with de-homogenized technique are used to analyze the residual stress and distortion of a 4 ft-wide wall printed in the Big Area Additive Manufacturing (BAAM) system. For experimental measurement on the wall printing, Infra-Red (IR) camera captures the temperature field, and Linear Variable Differential Transformer (LVDT) is installed to measure the warpage at the bottom surface. The experimental data are compared to the numerical analysis results. The temperature profile and the distortion profile from experiment are close to the simulation results. Damages due to residual stress and distortion are analyzed.

Kim, Pum↗
NASA NTRSDate not supplied

Additive Manufacturing: Disrupting Global Supply Chains and Enabling Sustainable Development

The integration of new materials and innovative manufacturing technologies into product supply chains are critically needed to address human and societal needs and to promote sustainable development and economic competitiveness. Recently, there has been tremendous growth in the additive manufacturing (AM) landscape with the introduction of high- end machines suitable for industrial applications. In addition, availability of desktop 3-D printers as well as open source printers and platforms have also facilitated the large scale growth of distributed manufacturing. The paradigm shift in thinking, where one can turn their design into product on demand, is leading to new business models and challenging traditional models of product development and distribution. In this presentation, an overview of different AM technologies will be provided along with technical challenges and opportunities. Various examples of materials (polymers, ceramics, metals, hybrids, and multi material systems) and structures achieved from utilizing a wide variety of additive manufacturing approaches will be provided. Technical challenges and opportunities for the utilization of additive manufacturing as a powerful enabler for sustainable development and disruptive technological threat to global supply chains for different materials and systems will be presented.

Additive Manufacturing↗
NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

pragmatic method↗
DOE OSTI2024

Development of a Method for Shape Optimization for a Gas Turbine Fuel Injector Design Using Metal-Additive Manufacturing

Adjoint shape optimization has enabled physics-based optimal designs for aerodynamic surfaces. Additive manufacturing (AM) makes it possible to manufacture complex shapes. However, there has been a gap between optimal and manufacturable surfaces due to the inherent limitations of commercial computational fluid dynamics (CFD) codes to implement geometric constraints during adjoint computation. In such cases, the design sensitivities are exported and used to perform constrained shape modifications using parametric information stored in computer aided design (CAD) files to satisfy manufacturability constraints. However, modifying the design using adjoint methods in CFD solvers and performing constrained shape modification in CAD can lead to inconsistencies due to different shape parameterization schemes. This paper describes a method to enable the simultaneous optimization of the fluid domain and impose AM manufacturability constraints, resolving one of the key issues of geometry definition for isogeometric analysis. Similar to a grid convergence study, the proposed method verifies the consistencies between shape parameterization techniques present within commercial CAD and CFD software during mesh movement as a part of the adjoint shape optimization routine. By identifying the appropriate parameters essential to a shape optimization study, the error metric between the different parameterization techniques converges to demonstrate sufficient consistencies for justifiable exchange of data between CAD and CFD. For the identified shape optimization parameters, the error metric to measure the deviation between the two parameterization schemes lies within the AM laser-powder bed fusion (L-PBF) process tolerance. Additionally, comparison for subsequent objective function calculations between iterations of the optimization loop showed acceptable differences within 1% variation between the modified geometries obtained using the two parameterization schemes. This method provides justification for the use of multiphysics guided adjoint design sensitivities computed in CFD software to perform shape modifications in CAD to incorporate AM manufacturability constraints during the shape optimization loop such that optimal designs are also additively manufacturable.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS2019

Evaluation Studies of Solid Oxide-Based Fuel Cells for Light-Weight Electrical Power in Aviation: Concepts and Opportunities for the Application of Additive Manufacturing

Currently NASA is investigating the feasibility of hybrid-electric, solid oxide fuel cell power (SOFC) systems for generating electrical power for airborne propulsion and secondary/auxiliary power. As part of this project, researchers are investigating the performance of SOFC hardware in aviation-like environments, to establish the barriers, and potential suitability, of this technology. Immediate findings indicate the unsuitability of current SOFC stack architectures with regards to ease of manufacture, specific energy, as well as environmental and mechanical durability. One possible solution is to create light-weight high specific energy density solid oxide fuel cells. The possibility may be achievable by the use of modern processing techniques such as additive manufacturing. Here I discuss the use additive manufacturing to fabricate ceramic anode, electrolytes, and cathode cells supported on various metal foams with predicted performance based upon variable porosities

Goldsby, Jon C.↗
NASA NTRSDate not supplied

Evaluations of Additively Manufactured Superalloy Lattice Blocks

Cast lattice block structures made up of high-temperature superalloys were previously shown to offer advantages in density, efficiency, and tailored properties. However, inconsistencies in casting die-fill, composition, and microstructure were identified as persistent issues with the casting process path. Three candidate lattice designs were screened through additive manufacturing of a superalloy. Laser powder bed fusion was applied with superalloy powder to produce lattice blocks for three-dimensional octahedral unit-cell designs of three heights. Properties of the structural designs versus additively manufactured lattices were compared, including structural dimensions, densities, defects, grain structures, crystallographic texture, and surface residual stresses. Findings indicate this concept could produce useful superalloy structures for high-temperature-capable static components requiring tailored density, and thermophysical and mechanical properties.

superalloy↗
DOE OSTI2018

Additive manufacturing of anisotropic hybrid NdFeB-SmFeN nylon composite bonded magnets

In this work, we demonstrate a novel method of extrusion-based 3D printing additive manufacturing of bonded magnets comprising 65 vol% anisotropic composite powders of Dy-free magfine Nd-Fe-B and Sm-Fe-N in nylon. The 3D printing was performed using a big area additive manufacturing (BAAM) process. The effects of various post-printing alignment with different magnetic field intensities and temperatures on the properties of the anisotropic bonded Nd-Fe-B + Sm-Fe-N composite magnets were investigated. Remanence increases with alignment magnetic field leading to an increase in energy product, (BH) max . For anisotropic Nd-Fe-B + Sm-Fe-N composite bonded magnets with a 65 vol% loading fraction, (BH) max of up to 11.3 MGOe are obtained. In addition, the magnetic properties of the bonded magnets can be tuned through the post-printing alignment of anisotropic particles in different directions without impairing the original shape-changing effect. Finally, this technique shows great promise for producing anisotropic bonded magnets with enhanced magnetic properties.

36 MATERIALS SCIENCE↗