Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cost-effectiveness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Deep Space Optical Communications (DSOC)

NASA’s future deep space science and exploration missions will require enhanced communications and navigation services. Laser communications offers expanded bandwidth and the potential for satisfying this need, with comparable mass and power as state of the art telecommunication systems. Consequently, NASA is planning a Deep Space Optical Communications (DSOC) technology demonstration, to retire the risk for future enhanced optical communication services. NASA’s upcoming Psyche Mission scheduled to launch in August of 2022 plans to host a DSOC flight laser transceiver (FLT) for demonstrating optical links from deep-space to earth. Existing ground assets retrofitted with laser transmitters and photon-counting receivers will be used for the technology demonstration. Advancing optical technology from near-Earth ranges to deep space (> 0.01 astronomical units or AU) involves orders of magnitude increased link difficulty (defined as data-rate squared distance). The plan to bridge the difficulty gap implements new technologies developed over the past two decades. These technologies emphasize high photon efficiency (HPE) with the use of high-peak-to-average power laser transmitters in space, and single photon counting sensitivity detectors, that together support signaling schemes for achieving approximately 23 information bits per detected photon. Implementing HPE schemes relies on accurate and stable pointing of narrow laser beams from space platforms using active control. Key developments needed for future technology infusion, following a successful DSOC technology demonstration, include, cost-effective ground infrastructure, long term reliability of space lasers and detection systems, and solutions for high precision laser ranging. The current status of the DSOC Project and plans for future development will be discussed in this paper.

Biswas, Abhijit↗
NASA NTRS2018

ASTERIA Operations Demonstrates the Value of Combining the Mission Assurance and Fault Protection Roles on CubeSats

On November 20, 2017, ASTERIA (Arcsecond Space Telescope Enabling Research in Astrophysics), a 6U CubeSat performing a technology demonstration of astrophysical measurements, deployed from the ISS. The technology demonstration goals to achieve precision photometry via arcsecond-level line-of-sight pointing error and highly stable focal plane temperature control were met by February 2018. Extended mission operations are ongoing, with the primary focus on observing nearby stars for transiting exoplanets. Throughout development and operations, the roles of mission assurance and fault protection have proven critical to achieving the primary technical goals and to maintaining a healthy spacecraft through multiple extended missions. Given the budget and schedule constraints typical of a CubeSat, innovative tailoring of processes has been critical to success throughout both development and operations of ASTERIA. Mission assurance plays an important role in identifying and evaluating risk and developing cost-effective mitigations. Flexibility in the fault protection design offers a variety of options for implementing risk mitigations as risks have been uncovered both in pre-delivery testing and in mission operations. This paper will discuss the approach taken on ASTERIA to implement mission assurance and fault protection and the resulting benefits to operational efficiency and success. It will briefly address the advantages of this approach during development, in which the combination of the roles provided mission assurance significant insight to system risks, which feeds back into testing methodologies and directly into fault protection design. Operations will be discussed in detail. During this phase, the roles merge to identify in-flight fault protection updates to efficiently respond to anomalies and improve the likelihood of successful technology demonstrations. The paper will also detail the tools that are used to analyse data, identify anomalies, and develop the updates to uplink to the spacecraft. Finally, the general operational approach will be discussed to highlight the usefulness of the ASTERIA processes and their applicability to future CubeSat missions.

Knapp, Mary↗
NASA NTRS2019

Application of GRACE to the Estimation of Groundwater Storage Change in a Data-poor Region: A Case Study of Ngadda Catchment in the Lake Chad Basin

The present study is to explore the feasibility of GRACE-based estimation of a groundwater storage change in a data-poor region using a case study of the Ngadda catchment in the Lake Chad Basin. Although the Ngadda catchment has only one set of in situ time series data of groundwater from 2006 to 2009 and a limited number of groundwater measurements in 2005 and 2009, GRACE-based groundwater storage change can be evaluated against thein situ groundwater measurements combined with specific yield data. The cross-correlation analysis in the Ngadda catchment shows that maximum rainfall reached in July and August, whereas both the maximum total water storage anomaly and the maximum groundwater storage anomaly occurred 2months later. Whereas the mean annual amplitude of total water storage anomaly is about 17cm from both the average total water storage anomaly from three mascon products and the one from three spherical harmonic products, the mean annual amplitude of soil moisture storage anomaly is substantially varied from5.58cm for CLM to about 14cm for NOAH and Mosaic. The goodness-of-fit tests show that CLM soil moisture produces the closest estimation of groundwater storage anomaly to thein situ groundwater measurements. The present study shows that GRACE-based estimation for groundwater storage anomaly can be a cost-effective and alternative tool to observe how groundwater changes in a basin scale under the limitation of modelling and in situ data availability.

GRACE↗
NASA NTRS2019

Uncooled Doped-Si Thermopiles for Thermal Land Imaging Applications

Sustained and enhanced land imaging is crucial for providing high-quality science data on change in land use, forest health, environment, and climate. Future thermal land imaging instruments operating in the 10-12 micron band will provide essential information for furthering our hydrologic understanding at scales of human influence, and producing field-scale moisture information through accurate retrievals of evapotranspiration (ET). To address the need for cost-effective future thermal land imaging missions we are developing novel uncooled doped-silicon thermopile detectors, an extension of a detector design concept originally developed at NASA-Goddard for planetary science applications. These doped-Si thermopile detectors have the potential to offer superior performance in terms of sensitivity, speed, and customization, when compared to current commercial-off-the-shelf uncooled detector technologies. Because cryocooler technology does not need to be fielded on the instrument, these and other uncooled detectors offer the benefit of greatly reduced instrument cost, mass, and power at the expense of some acceptable loss in detector sensitivity. We present the motivation for an uncooled thermal imaging instrument, our doped-Si thermopile detector concept, and performance expectations and comparisons. We also provide an update on the current status of this detector technology development.

Thermopiles↗
NASA NTRS2019

IceCube: Spaceflight Demonstration of 883-GHz Cloud Radiometer for Future Science

Cloud ice play important roles in Earth’s climate and weather systems through their interactions with atmospheric radiation, dynamics, energy and precipitation processes. Submillimeter (submm) wave remote sensing at 200-1000 GHz is able to provide the sensitivity not covered by visible (VIS)/infrared (IR) and low-frequency microwave (MW) sensors (10-183 GHz), and measure cloud ice in the middle-to-upper troposphere. The IceCube 883-GHz cloud radiometer is the latest of NASA’s efforts to advance the technology readiness level (TRL) of submm-wave receiver technology for future compact, low-cost implementation of Earth observing systems. Emerging CubeSat opportunities allow a fast-track development and spaceflight demonstration of IceCube on a 3-U CubeSat. Funded by NASA’s In-Space Validation of Earth Science Technologies (InVEST) program and Science Mission Directorate (SMD), IceCube is the first CubeSat developed and flown by Goddard Space Flight Center (GSFC) in 2.5 years, using commercial off-the-shelf (COTS) components and subsystems. It was successfully released from International Space Station (ISS) in May 2017, acquired 15-month science data and produced the first global map of the 883-GHz cloud ice. It achieved all mission objectives and provided a pathway for future cost-effective cloud observations from CubeSat constellation.

Submm-wave remote sensing↗
NASA NTRS2019

AMUSS - astrophysics miniaturized UV spatial spectrometer for spectroscopic studies of diffuse astrophysical objects

Traditional slit spectrographs lack the sensitivity for detecting the faint emission. We utilize a novel spectroscopic instrument, Astrophysics Miniaturized UV Spatial Spectrometer (AMUSS), which provides significant gains in sensitivity over a slit-spectrograph, and makes it possible in relatively short time, to study important UV lines in ultra-high spectral resolution that can probe the diffuse hot gas in these objects. AMUSS’s ultra-compact, the cost-effective design makes it a suitable instrument for CubeSats, SmallSats or as a small payload on large future UV missions. We describe two of the science cases in detail below that encompass the range of wavelengths and surface brightness that we expect to encounter.

Sahai, Raghvendra↗
NASA NTRS2025

Airports as Energy Nodes Activity Summary

Advanced aircraft concepts that use non-traditional aviation energy storage methods such as batteries or cryogenic hydrogen are in development and expected to enter regular service at airports worldwide within the next decade. The energy needs for these aircraft may quickly overwhelm the existing energy infrastructure at airports, particularly at smaller and more remote facilities. Without energy upgrades, these airports will not be able to host these advanced vehicles, but without the advanced vehicle traffic, these airports will not have the rationale or funding to build up their energy infrastructure. The Airports as Energy Nodes (ÆNodes) activity, a collaboration between the National Aeronautics and Space Administration (NASA) and the National Renewable Energy Laboratory (NREL), was executed to understand and model the energy needs that advanced aircraft concepts may levy on these smaller airports, determine cost-effective approaches to enhance the airport energy infrastructure, and demonstrate the enhanced resilience of these energy infrastructure upgrades to the airport and surrounding community via “digital twin” simulation at relevant energy and dynamic time scales. The ÆNodes team also investigated future reference aircraft designs and materials to enable cryogenic hydrogen storage for aircraft. The ÆNodes team conducted analysis at two U.S. airport partner sites — Winchester Regional Airport in Winchester, Virginia, and Tweed/New Haven Airport in New Haven, Connecticut. The goal of this partnership was to develop data and reference infrastructure designs that could accommodate advanced aircraft in the future at these airports while also enhancing the resiliency of the energy supply to the surrounding airport community, which could be used to capture funding to enable the infrastructure upgrades. Over the course of the study, a method was developed to estimate air traffic requiring advanced energy services over the course of a year using a mix of historical data and companion studies on advanced aircraft transportation networks. The study has concluded at NASA but continues at NREL, who will develop a final report discussing the energy infrastructure upgrades and digital twin results. Preliminary results indicate that unrestricted adoption of advanced battery-electric aircraft may double traffic at these airports and increase peak daily power usage by an order of magnitude, while increase electricity energy needs by a factor of two to four. The infrastructure upgrades necessary to accommodate these increased energy needs could be used to provide enhanced energy services to the airport community to offset the cost and increase the utility of the upgrades, which will be described in the NREL final report.

Airports↗
NASA NTRS2026

Remote Sensing-Driven Hydrodynamic Modeling in Data-Scarce Regions: Integrating ICESat-2, Sentinel-2, SWOT and Re-analysis Models for Coastal Monitoring

Hydrodynamic models in coastal and estuarine systems are typically constrained by sparse bathymetry, boundary, and validation data, especially in regions where field campaigns are costly or impractical. Here we develop and test a fully satellite-driven framework for hydrodynamic modeling in South Africa’s Langebaan Lagoon without using any local in situ measurements. Bathymetry is derived by training multispectral Sentinel-2 reflectance against ICESat-2 ATL24 photon-derived depths using an XGBoost model optimized with Bayesian search. The final satellite-derived bathymetry reproduces independent ATL24 points with RMSE = 0.45 m and R 2 = 0.97. This bathymetry was used in a depth-averaged Delft3D Flexible Mesh model driven at the open boundary by TPXO tidal harmonics and by ERA5 winds. We validate modeled water surface elevation against 16 SWOT low-rate (250 m, unsmoothed) passes in 2023. SWOT–model comparisons yield an overall RMSE of 0.11 m and R 2 = 0.61, with typical point differences <0.10 m (∼7% of the 1.5 m tidal range), and showed consistent spatial gradients in water level from the offshore boundary, through Saldanha Bay, and into the lagoon. At the offshore boundary, TPXO and SWOT sea surface heights agree closely (R 2 = 0.86). A simple phase adjustment of ∼26,min between TPXO and SWOT lowers the RMSE from 0.18,m to 0.11,m, showing that phase offset accounts for some of the discrepancy, with additional errors likely linked to non-tidal signals. Our results demonstrate that combining passive optical, photon-counting LiDAR, radar interferometry, and global tidal/atmospheric models enables robust, transferrable hydrodynamic modeling in data-scarce coastal systems, offering a cost-effective pathway for monitoring.

ICESat-2↗
NASA NTRS2026

Hybrid Modeling Study on Grain Evolution in the Metal Welding Process and Its Potential Lunar Application

Metal is most commonly used structural material in a wide range of spacecraft, and welding is the principal method for joining metal components into functional systems. However, conducting welding experiments under extreme environments—such as microgravity or vacuum conditions in space—is prohibitively expensive and experimentally challenging. To overcome these limitations, multi-physics computational welding models provide a cost-effective and versatile alternative. In this work, the authors have developed a coupled thermal (fluid) microstructure simulation framework to model metal welding under varying gravity conditions. The framework integrates a mixed-mode heat transfer formulation (conduction, convection, and radiation) with molten pool fluid dynamics, enabling accurate prediction of temperature fields and weld-pool geometry. A grain growth model is further incorporated to capture the spatial and temporal evolution of microstructure, including grain size distribution and morphological transitions during solidification. This approach provides detailed insight into molten pool evolution and grain-level microstructure development throughout the welding process. By explicitly parameterizing environmental conditions, the model supports extrapolation to off-Earth manufacturing scenarios such as welding on the lunar surface. Tantalum—chosen in this study due to its high melting point, oxidation resistance, and mechanical stability at elevated temperatures—serves as the material system for model demonstration. Beyond Tantalum, the integrated multi-physics framework offers broad applicability for predictive welding simulations of various structural and refractory metals or alloys used in extreme terrestrial or extraterrestrial environments.

kinetic Monte Carlo (SPPARKS)↗
NASA NTRSDate not supplied

Assembly and Integration Status of a High Fidelity Ground Test Bed for the Water Processor Assembly

The Water Recovery System (WRS) is a critical component of life support aboard the International Space Station (ISS) and will play an essential role in future missions beyond Low Earth Orbit (LEO). Its primary functional units – the Urine Processor Assembly (UPA), Brine Processor Assembly (BPA), and Water Processor Assembly (WPA) – must be evaluated for extended operation, dormancy resilience, material obsolescence, and reliability under exploration-driven constraints. Ground testing is vital for developing these technologies and generating statistically relevant reliability assessments, which requires extended runtime under integrated, Flight-like conditions. Currently, no high-fidelity, fully integrated WPA ground test bed exists to support these objectives. To address this gap, NASA is developing a WPA test bed at Marshall Space Flight Center (MSFC) that combines downgraded ISS flight hardware with functionally flight-like components in a cost-effective configuration while maintaining priority hardware investigations. This paper describes the current status of hardware assembly and integration, outlines key challenges such as simulating microgravity effects and mitigating obsolescence, and presents future test objectives including software development, reliability assessments, dormancy studies, and exploration-oriented upgrades.

Mary-Elizabeth Davis↗
NASA NTRS2026

Smart Process Planning for Automated Fiber Placement

Many industries, including aerospace, automotive, wind energy, maritime, and sporting goods, rely on strong, lightweight materials called composites. These materials are made by layering fibers, which can come in the form of narrow strips or wider sheets, and setting them in a polymer matrix. One of the most advanced ways to make these parts is through automated fiber placement, where a machine lays down the fibers in precise patterns. This method can create very efficient and strong designs, but it is complex, expensive, and often depends heavily on the experience of skilled engineers. Today, the design, manufacturing, and inspection stages of composite production are usually handled separately. This separation means that important information, such as how a part will be built or what defects might occur, is not always shared between stages. As a result, parts may not be as lightweight, strong, or defect-free as possible, and the process can take longer and cost more. This research develops a smart process planning system that connects design, manufacturing, and inspection into one continuous process. Built as software that works with existing tools, the system can automatically plan how the fibers are placed, predicting and reducing defects while improving both manufacturability and strength. The system optimizes not only individual layers but also how defects are distributed across all layers, preventing them from stacking up in ways that weaken the final part. It also uses inspection results from completed parts to improve future designs, creating a feedback loop where each stage informs the others. The system was tested by designing a composite panel using this new approach and comparing it to a panel made with state-of-the-art manual planning methods. The results showed that the system could intentionally control where defects appeared and increase the efficiency of the planning process. By unifying design, manufacturing, and inspection, this research shows a way to make advanced composite manufacturing more efficient, consistent, and cost-effective. This approach lowers the barrier to using automated fiber placement and opens the door for its wider adoption not only in aerospace but also in industries such as automotive, wind energy, maritime, and sporting goods, where strong and lightweight structures are essential.

Computer-Aided Process Planning↗
NASA NTRSDate not supplied

Assembly and Integration Status of a High Fidelity Ground Test Bed for the Water Processor Assembly

The Water Recovery System (WRS) is a critical component of life support aboard the International Space Station (ISS) and will play an essential role in future missions beyond Low Earth Orbit (LEO). Its primary functional units – the Urine Processor Assembly (UPA), Brine Processor Assembly (BPA), and Water Processor Assembly (WPA) – must be evaluated for extended operation, dormancy resilience, material obsolescence, and reliability under exploration-driven constraints. Ground testing is vital for developing these technologies and generating statistically relevant reliability assessments, which requires extended runtime under integrated, Flight-like conditions. Currently, no high-fidelity, fully integrated WPA ground test bed exists to support these objectives. To address this gap, NASA is developing a WPA test bed at Marshall Space Flight Center (MSFC) that combines downgraded ISS flight hardware with functionally flight-like components in a cost-effective configuration while maintaining priority hardware investigations. This paper describes the current status of hardware assembly and integration, outlines key challenges such as simulating microgravity effects and mitigating obsolescence, and presents future test objectives including software development, reliability assessments, dormancy studies, and exploration-oriented upgrades.

Water Processor Assembly↗
NASA NTRSDate not supplied

Characterization of Quicksounder ATMS at Instrument Level TVAC

QuickSounder (QS) is the pathfinder space mission for the next generation of NOAA LEO environmental satellites in the NEON program, follow-on to the JPSS program. It is a collaborative initiative between NASA and NOAA to verify rapid and cost-effective delivery of small Earth observation satellites. QuickSounder is focusing on mission elements other than science performance. In this context, an existing sensor, the refurbished ATMS EDU (Advanced Technology Microwave Sounder, Engineering Development Unit) was chosen as the QuickSounder payload. This poster discusses the performances of QuickSounder ATMS during thermal vacuum (TVAC) calibration to ensure that QS ATMS is characterized and calibrated in the same manner as JPSS ATMS units, even though science performance attributes are not the priority of this mission.

Saji Abraham↗
NASA NTRS2025

A Review of Direct Ink Writing of Polymer Derived Ceramics

With the growing demand for materials capable of withstanding extreme temperatures and pressures, ceramic components with exceptional corrosion resistance and reliable mechanical properties have experienced a significant surge in demand. However, traditional ceramic forming methods involve high-temperatures and energy-intensive processes that often struggle to produce complex parts or composites efficiently. Polymer-Derived Ceramics (PDCs) offer a transformative solution by using polymeric precursors that can be converted into a wide variety of silicon-based and non-silicon-based ceramics through heat treatment. The polymeric nature of PDC precursors enables the fabrication of geometrically intricate components using conventional polymer-forming techniques at significantly lower processing temperatures. Furthermore, PDCs are well-suited for additive manufacturing (AM), allowing the production of complex structural and functional components through cost-effective, low-temperature processes. By leveraging the diverse properties of PDC materials – each with unique advantages and limitations – manufacturers can optimise performance for specific applications. This review provides an overview of the types of PDCs developed to date and their broad range of applications. Specifically, it delves into the Direct Ink Writing (DIW) process, exploring its rheological requirements and the critical role of fillers in tailoring the rheological properties of polymeric precursors to meet the specific demands of DIW.

Victoria Bishop↗
NASA NTRS1995

Functions Performed by Mission Operations

We propose the series of three presentations described above for inclusion in your symposium. These presentations are similar to those we presented last November in plenary session at the Third International Symposium on Space Mission Operations and Ground Data Systems. Each presentation lasts 40 minutes and the presentations are designed to be given in order. The information in our presentations is extracted from a book of the same title scheduled for publication in August, 1995. Please note that since we have a book covering this topic, we will not prepare separate papers. An overview of each presentation is shown below.

Cost-Effective Mission↗