Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Dispersion of Nano-Sized Oxide Particles in Ni-based Alloy

High temperature materials with a good resistance to oxidation or corrosion are crucial for the Generation IV nuclear system such as VHTR (Very High Temperature Reactor). While several commercial Ni-based high temperature alloys have been among the candidate ones for the IHX (intermediate heat exchanger) or HGD (hot gas duct) of VHTR, they disclose their insufficiency for the application to the anticipated outlet temperature range such as 900 deg. C or above. Unless the operating temperature is significantly lowered and the performance of the system drops in consequence, a breakthrough in the candidate materials for the key components shall be necessary for the realization of the system. Feasibility for the oxide dispersion strengthening (ODS) of Ni-based alloys was studied by fabrication of alloy 617-base ODS alloy. Alloy 617 powders were mechanically alloyed (MA) with 0.3 wt% Y{sub 2}O{sub 3} powders of around 30 nm in diameter using a horizontal ball mill (ZoZ CM 08). After degassing and canning procedure, MA powders were hot extruded. Extruded alloy samples were tensile tested at high temperatures as well as at room temperature. Also high temperature creep rupture tests were conducted at 950 deg. C in air under 20 and 25 MPa, respectively. The behavior of oxide particles within the Ni-based alloy matrix was investigated by mechanical alloying of Ni- Cr-Fe ternary alloy powders and pure Ni powders with oxide particles, respectively. Oxide such as Y{sub 2}O{sub 3}, Cr{sub 2}O{sub 3}, HfO{sub 2}, ZrO{sub 2}, TiO{sub 2}, La{sub 2}O{sub 3} were chosen from the thermodynamic point of view as the first stable candidates from more than twenty oxides, nitrides and carbides. The behavior of oxide particle within the MA powder matrix along with the temperature was characterized by using high temperature XRD (X-ray Diffractometer) and (HR)TEM (High Resolution Transmission Electron Microscope). Creep rupture tests of the ODS alloy samples at 950 deg. C showed one order of magnitude lower creep rates than those of the corresponding alloy. (authors)

36 MATERIALS SCIENCE↗

Structural Effects of Postulated Hydrogen Explosions in Process Piping and Vessels - 20274

At Savannah River Site (SRS), preparations to startup new liquid waste operations and recent advances in understanding thermolytic hydrogen generation have led to several recent studies on the structural effects of postulated hydrogen explosions. This paper reports on seven representative piping and vessel cases that are evaluated for deflagrations, detonations, and deflagration-to-detonation transition (DDT) assuming the initial mixture is stoichiometric hydrogen and air. The evaluations are based on the approach used by the Department of Defense for analyzing structures subjected to accidental explosions and include inelasticity, dynamic structural amplification, and material strain-rate effects. Evaluation criteria consider the potential for repeated explosions causing fatigue but also consider that some degree of permanent plastic deformation is acceptable as long as rupture is prevented. Specific conclusions depend on the assumed pre-ignition pressure. If the pre-ignition pressure is atmospheric and if the components are designed to a code from the American Society of Mechanical Engineers, the components evaluated are expected to plastically deform but not rupture under the explosion scenarios considered. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Contaminant Entrainment in a Liquid Fuel Fire with Multi-Component Evaporation Droplet Model

A number of fire scenarios can result in the release of hazardous chemical or radiological contaminants as sub-micron solid particulates, posing a significant danger of inhalation. These particulates may be entrained in the air around the fire through a variety of mechanisms including liquid droplet formation above the boiling surface of the contaminated fuel. The formation of both film drops from the rupture of a liquid film as a boiling bubble bursts and jet drops from the collapse of the cavity of a ruptured bubble may be involved. A 2015 study by Brown and Louie focused on such a fire scenario to investigate the physics of contaminant release. This paper extends that study by supplementing the existing physics models with a multicomponent evaporation mechanism, where liquid droplets formed near the boiling fuel surface experience evaporation of their various components at different rates based on distinct material properties (density, specific heat, heat of vaporization, etc.). As in the Brown and Louie study, the Sierra low-Mach module Fuego is used as the Lagrangian-Eulerian code for simulation of this scenario. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Computational Investigation of Fuel Dispersal Phenomena during Large-Break Loss of Coolant Accident in Light-Water Reactors

In the event of cladding rupture, which could occur in light water reactor fuel assemblies during a loss-of-coolant accident (LOCA), fuel particles, along with fission gases, can be expelled into the reactor core from the fractured fuel rod. This expulsion of fragmented fuel particles, referred as fuel dispersal, is the subject of investigation to evaluate the safety implications of increasing fuel burnup in light water reactors, with a specific focus on fuel fragmentation, relocation, and dispersal. Particle trajectories and the resulting mass distribution of the settled particles within the reactor pressure vessel can pose a long-term cooling challenge for the reactor core. The fuel dispersal phenomenon is significantly influenced by the ejection characteristics of the fuel fragments, as well as the size and shape of the cladding rupture and fuel rod depressurization history during LOCA transients. In this study, the transport of fuel particles within a scaled 5 × 5 lattice of a pressurized water reactor rod bundle geometry is modeled through a two-fluid Eulerian framework that treats the gas and solid phases as interpenetrating continua. The required boundary conditions are evaluated from the fuel performance code BISON in a postulated large-break LOCA scenario. The modeling framework considers solid fuel particles as granular matter, interacting with the gaseous dry steam phase and fission gases through the governing interfacial momentum and energy exchange between the gas and solid phases. The simulation results provide the volume fraction of the solids settled on the bottom surface of the fuel bundle, quantifying the deposition within the bundle geometry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

FY25 status report on the addition of candidate materials in Class B Code Case

This report provides the time-dependent allowable stress calculation strategy leveraging the limited creep rupture tests data generated to support the allowable stress for 100,000 hours in American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), Section II, Part D. A variable confidence index procedure to extrapolate material properties to support 500,000 hours design life is discussed. Time-dependent allowable stresses for Class B component design and analysis are presented for Grade 1 and Grade 2 of Alloy 625. The presented data extrapolation and allowable stress calculation method will support new material addition using limited creep rupture data in the new ASME Boiler and BPVC, Section III, Division 5, Class B rules.

Part D↗

Fuel Bonding and its Impact on Axial Gas Communication Behavior in Light-Water Reactor Fuel Rods

Axial gas communication concerns the flow along the axial axis of nuclear fuel rods during ramp and loss of coolant accident (LOCA) conditions. During power ramps, the higher linear heat generation rate may cause fuel-to-clad gap closure that may prevent transport of released fission gases to the plenum. Upon reduction in power the gas then can communicate to the plenum. This phenomenon has been experimentally observed by short power dips during ramp experiments completed at the Risø reactor. At higher burnups it is observed that the UO2 fuel and Zircaloy cladding forms a chemical bond. This bond results in complete closure of the gap. When these high burnup rods are subjected to a LOCA, the bond has implications on both the mechanical response (i.e., ballooning) of the cladding and subsequent fuel relocation and axial gas communication. In the LOCA scenario, gas communication is of interest in two different regimes: 1) pre-rupture communication from the plenum towards the lower pressure ballooning area and 2) the post-rupture depressurization of the plenum to the external system pressure. In both regimes the presence of a fuel-to-cladding bond will impact the rate of depressurization. In this work we present a fuel-to-clad bonding model that is coupled to an existing axial gas communication model framework in the BISON fuel performance code. The effect of considering the bond on fuel performance modeling predictions is presented through comparisons to existing experimental data. Experiments considered include several rods from the Halden IFA-650 test series. An evaluation on a full-length rod that explores the combined effect of plenum size and bonding status on axial gas communication behavior is also presented.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effects of Geometric Discontinuities on Creep Behavior of Alloy 617

Due to the excellent long-term high-temperature performance of Alloy 617, the Alloy has been identified as the primary structural material for the intermediate heat exchanger of the Very High Temperature Reactor (VHTR). Both the base and welded alloy has been qualified to be used up to 950 °C up to 100,000 hours by the American Society of Mechanical Engineer (ASME) Boiler and Pressure Vessel Code (BPVC). The qualification properties of the material were exclusively determined by uniaxial creep tests. The components may, however, experience multiaxial stress conditions in service due to the reactor geometry. This study used notched creep tests to investigate the effect of geometric discontinuities on creep behavior of both the base and welded Alloy 617. The V-notch tests reveal that the geometric discontinuities do not reduce the creep rupture live under high and intermediate stress conditions. The U-notch tests show that a larger radius notch behave in a similar way as a straight gauge section of a uniaxial test. The creep rupture live of the welded alloy was slightly longer than the base metal.

36 - MATERIALS SCIENCE↗

SELF-HEALING PNEUMATIC ACTUATOR DIAPHRAGMS

In the oil and gas industry, damaged diaphragms in pneumatic actuators can lead to unintended methane leaks, increasing emissions. In this work, replacement self-healing diaphragms are manufactured for a commercial pneumatic actuator. To enable self-healing, hollow microvascular networks are created within the diaphragms using sacrificial 3D printed PLA w/ tin(II) oxalate. These microvascular networks are filled with healing chemistries and, upon damage, rupture. After rupturing, the healing chemistries mix and cure to “heal” the damage and reduce leaks. Separate actuator test stands using nitrogen gas and using natural gas were developed to assess the healing performance of diaphragms. A fatigue stand was also developed to evaluate the effects of the different microvascular network geometries on the fatigue life of diaphragms. Our results demonstrate self-healing in diaphragms subjected to damage and tested for leaks. In fatigue testing, our results indicate that the introduction of microvascular networks does not influence the fatigue life.

Self-healing, pneumatic actuator↗

Flooding Experiments and Modeling for Improved Reactor Safety

Countercurrent two-phase flow and “flooding” phenomena in light water reactor systems are being investigated experimentally and analytically to improve reactor safety of current and future reactors. The aspects that will be better clarified are the effects of condensation and tube inclination on flooding in large diameter tubes. The current project aims to improve the level of understanding of flooding mechanisms and to develop an analysis model for more accurate evaluations of flooding in the pressurizer surge line of a Pressurized Water Reactor (PWR). Interest in flooding has recently increased because Countercurrent Flow Limitation (CCFL) in the AP600 pressurizer surge line can affect the vessel refill rate following a small break LOCA and because analysis of hypothetical severe accidents with the current flooding models in reactor safety codes shows that these models represent the largest uncertainty in analysis of steam generator tube creep rupture. During a hypothetical station blackout without auxiliary feedwater recovery, should the hot leg become voided, the pressurizer liquid will drain to the hot leg and flooding may occur in the surge line. The flooding model heavily influences the pressurizer emptying rate and the potential for surge line structural failure due to overheating and creep rupture. The air-water test results in vertical tubes are presented in this paper along with a semi-empirical correlation for the onset of flooding. The unique aspects of the study include careful experimentation on large-diameter tubes and an integrated program in which air-water testing provides benchmark knowledge and visualization data from which to conduct steam-water testing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Measurement of the flow properties within a copper tube containing a deflagrating explosive

We report on the propagation of deflagration waves in the high explosive (HE) PBX 9501 (95 wt % HMX, 5 wt% binder). Our test configuration, which we call the def1agration cylinder test (DFCT), is fashioned after the detonation cylinder test (DTCT) that is used to calibrate the JWL detonation product equation of state (EOS). In the DFCT, the HE is heated to a uniform slightly subcritical temperature, and is ignited at one end by a hot wire. For some configurations and initial conditions, we observe a quasi-steady wave that flares the tube into a funnel shape, stretching it to the point of rupture. This behavior is qualitatively like the DTCT, such that, by invoking certain additional approximations that we discuss, its behavior can be analyzed by the same methods. We employ an analysis proposed by G.I. Taylor to infer the pressure-volume curve for the burning, expanding flow. By comparing this result to the EOS of HMX product gas alone. we infer that only {approx}20 wt% of the HMX has burned at tube rupture. This result confirms pre-existing observations about the role of convective burning in HMX cookoff explosions.

66↗

Creeping faults: Good news, bad news?

The motion of the Earth's tectonic plates drive fault slip. Some faults slip in sudden movements, releasing great amounts of energy during large earthquake ruptures, while others slip in steadier movements which release energy more slowly. The latter, known as creeping faults, are believed to be less hazardous but there is mounting evidence that they are more complex than previously thought and can also pose a significant hazard. A recent review by Harris [2017] documents the earthquake potential of creeping faults in shallow continental fault zones from worldwide data. Furthermore, she presents a comprehensive review of prior studies; key insights into when, where, and why fault creep takes place and under which conditions creeping faults may represent high seismic hazard and suggests some directions for future research.

58 GEOSCIENCES↗

Hemp-Fiber-Reinforced Unsaturated Polyester Composites: Optimization of Processing and Improvement of Interfacial Adhesion

The processing variables for making hemp-fiber-reinforced unsaturated polyester (UPE) composites were optimized through orthogonal experiments. It was found that the usage of initiator, methyl ethyl ketone peroxide, had the most significant effect on the tensile strength of the composites. The treatment of hemp fibers with a combination of 1, 6-diisocyanatohexane (DIH) and 2-hydroxylethyl acrylate (HEA) significantly increased tensile strength, flexural modulus of rupture and flexural modulus of elasticity, and water resistance of the resulting hemp-UPE composites. FTIR spectra revealed that DIH and HEA were covalently bonded to hemp fibers. Scanning electronic microscopy graphs of the fractured hemp-UPE composites demonstrated that treatment of hemp fibers with a combination of DIH and HEA greatly improved the interfacial adhesion between hemp fibers and UPE. The mechanism of improving the interfacial adhesion is proposed.

1,6-diisocyanatohexane↗

Ball-on-ring test validation for equibiaxial flexural strength testing of engineered ceramics

The validation of a ball-on-ring, equibiaxial flexural strength method to obtain the transverse rupture strength (TRS) of right cylindrical ceramic specimens was performed in this study. Validation of the test method was achieved using commercially available engineered high purity alumina disks and finite element (FE) model analysis. The validated fixture was then used to obtain the TRS and Weibull statistical analysis of MgO-partially stabilized zirconia (MSZ) and Y 2 O 3 -partially stabilized zirconia (YSZ) ceramic disks. TRS data for alumina, MSZ, and YSZ agreed with the TRS values reported in the literature. A statistically relevant number of samples (N > 30) for each material were tested to allow for a Weibull statistical analysis. Weibull parameters for these materials were within the expected values for engineered ceramics. The characteristic strength for alumina, MSZ, and YSZ were determined to be 289, 786, and 814 MPa, respectively. The Weibull modulus was determined between 10 and 25 for each material, which is typical of engineered ceramics. In addition, FE model results were in close agreement with experimental fracture values for the three ceramic materials tested in this study.

36 MATERIALS SCIENCE↗

Engineering evaluation of the EQSIM simulated ground-motion database: The San Francisco Bay Area region

Ground-motion simulations for infrequent earthquake scenarios are gaining increasing interest in the engineering community for their potential to inform performance-based structural design and assessment, particularly in regions where major earthquakes are expected, but recordings from consistent historical events are not available. However, the absence of empirical data makes the evaluation of such scenarios and the interpretation of the simulation results very challenging. In this context, this paper presents the evaluation of the first EQSIM (v.1.1.0) ground-motion simulations generated for the San Francisco Bay Area (SFBA) region. The current database, which is at the first stages of development, includes eight realizations of a Hayward Fault M w 7 event. The evaluation of the simulated motions is first conducted on the average ground-motion amplitudes through comparison against the NGA-W2 GMPEs and a selected population of real records. A methodology for selecting a population of real records consistent with the simulated event is proposed. The objective of the proposed evaluation is twofold: (1) build confidence in the realistic character of the simulated motions for their use in engineering applications and (2) offer a critical physics-based interpretation of the simulation results that can help improve key features of the simulation models. To further investigate the implications of using the simulated ground motions for site-specific structural assessments, the ASCE7-16 approach is employed for the analysis of two hazard-consistent near-field sites in the SFBA. Results are discussed. Furthermore, this study offers a critical review of the EQSIM (v.1.1.0) SFBA ground-motion simulations and suggestions for improving the earthquake rupture models.

58 GEOSCIENCES↗

A Complicated Postsurgical Echinococcal Cyst Treated with Radiofrequency Ablation

Surgery of hydatid cysts is often complicated with intrabiliary rupture (IBR), which if not recognized may lead to biliary fistula with rather high rates of morbidity and mortality. We report our experience with the application of radiofrequency (RF) ablation for the treatment of an operated hepatic echinococcal cyst which was complicated with biliocystic communication and cysteocutaneous fistula with bile leakage. RF ablation was performed under CT guidance into the remaining cyst through the cutaneous fistula. Since ablation of the cyst and the fistula the patient has been asymptomatic.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Left Gastric Artery Aneurysm: Successful Embolization with Ethylene Vinyl Alcohol Copolymer (Onyx)

Patients with left gastric artery aneurysms present with hemorrhagic shock due to rupture or occasionally it is an incidental finding on abdominal CT examinations. Due to the increased morbidity and mortality from this condition, adequate diagnosis and treatment are essential. In this article we present a patient with a left gastric artery aneurysm treated with a new embolization agent, ethylene vinyl alcohol copolymer (Onyx)

62 RADIOLOGY AND NUCLEAR MEDICINE↗

The Endovascular Management of Iliac Artery Aneurysms

Background: Isolated aneurysms of the iliac arteries are uncommon. Previously treated by conventional surgery, there is increasing use of endografts to treat these lesions. Purpose: The purpose of this study was to assess the efficacy, safety, and durability of the stent-grafts for treatment of iliac artery aneurysms (IAAs). The results of endografting for isolated IAAs over a 10-year period were analyzed retrospectively. The treatment methods differed depending on the anatomic location of the aneurysms. Twenty-one patients (1 woman, 20 men) underwent endovascular stent-graft repair, with one procedure carried out under emergency conditions after acute rupture. The mean aneurysm diameter was 4.6 cm.Results:The procedural technical success was 100%. There was zero 30-day mortality. Follow-up was by interval CT scans. At a mean follow-up of 51.2 months, the stent-graft patency rate was 100%. Reintervention was performed in four patients (19%): one patient (4.7%) with a type I endoleak and three patients (14.3%) with type II endoleaks.Conclusion:We conclude that endovascular repair of isolated IAAs is a safe, minimally invasive technique with low morbidity rates. Follow-up results up to 10 years suggest that this approach is durable and should be regarded as a first treatment option for appropriate candidates.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Endovascular Treatment of a Carotid Dissecting Pseudoaneurysm in a Patient with Ehlers-Danlos Syndrome Type IV with Fatal Outcome

We present a patient with Ehlers-Danlos syndrome type IV (EDS IV) with a carotid dissecting pseudoaneurysm causing severe carotid stenosis. This lesion was treated endovascularly. Unfortunately, the patient died of remote vascular catastrophes (intracranial hemorrhage and abdominal aortic rupture). This unique case illustrates the perils of endovascular treatment of EDS IV patients and the need for preoperative screening for concomitant lesions. It also shows that a dissecting pseudoaneurysm can feasibly be treated with a covered stent and that closure is effective using Angioseal in patients with EDS IV.

62 RADIOLOGY AND NUCLEAR MEDICINE↗